Merge branch 'spear/dt' into spear/clock

Conflicts:
	arch/arm/mach-spear3xx/clock.c
	arch/arm/mach-spear3xx/include/mach/generic.h
	arch/arm/mach-spear3xx/include/mach/misc_regs.h
	arch/arm/mach-spear3xx/spear320.c
	arch/arm/mach-spear6xx/clock.c
	arch/arm/mach-spear6xx/include/mach/misc_regs.h

Resolve even more merge conflicts.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/arm/spear-timer.txt

+* SPEAr ARM Timer
+
+** Timer node required properties:
+
+- compatible : Should be:
+	"st,spear-timer"
+- reg: Address range of the timer registers
+- interrupt-parent: Should be the phandle for the interrupt controller
+  that services interrupts for this device
+- interrupt: Should contain the timer interrupt number
+
+Example:
+
+	timer@f0000000 {
+		compatible = "st,spear-timer";
+		reg = <0xf0000000 0x400>;
+		interrupts = <2>;
+	};

arch/arm/boot/dts/spear300-evb.dts

@@ -87,6 +87,31 @@ sdhci@70000000 {
 
 		smi: flash@fc000000 {
 			status = "okay";
+			clock-rate=<50000000>;
+
+			flash@f8000000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xf8000000 0x800000>;
+				st,smi-fast-mode;
+
+				partition@0 {
+					label = "xloader";
+					reg = <0x0 0x10000>;
+				};
+				partition@10000 {
+					label = "u-boot";
+					reg = <0x10000 0x40000>;
+				};
+				partition@50000 {
+					label = "linux";
+					reg = <0x50000 0x2c0000>;
+				};
+				partition@310000 {
+					label = "rootfs";
+					reg = <0x310000 0x4f0000>;
+				};
+			};
 		};
 
 		spi0: spi@d0100000 {
@@ -119,87 +144,87 @@ i2c0: i2c@d0180000 {
 			};
 
 			kbd@a0000000 {
-				linux,keymap = < 0x00010000
-						 0x00020100
-						 0x00030200
-						 0x00040300
-						 0x00050400
-						 0x00060500
-						 0x00070600
-						 0x00080700
-						 0x00090800
-						 0x000a0001
-						 0x000c0101
-						 0x000d0201
-						 0x000e0301
-						 0x000f0401
-						 0x00100501
-						 0x00110601
-						 0x00120701
-						 0x00130801
-						 0x00140002
-						 0x00150102
-						 0x00160202
-						 0x00170302
-						 0x00180402
-						 0x00190502
-						 0x001a0602
-						 0x001b0702
-						 0x001c0802
-						 0x001d0003
-						 0x001e0103
-						 0x001f0203
-						 0x00200303
-						 0x00210403
-						 0x00220503
-						 0x00230603
-						 0x00240703
-						 0x00250803
-						 0x00260004
-						 0x00270104
-						 0x00280204
-						 0x00290304
-						 0x002a0404
-						 0x002b0504
-						 0x002c0604
-						 0x002d0704
-						 0x002e0804
-						 0x002f0005
-						 0x00300105
-						 0x00310205
-						 0x00320305
-						 0x00330405
-						 0x00340505
-						 0x00350605
-						 0x00360705
-						 0x00370805
-						 0x00380006
-						 0x00390106
-						 0x003a0206
-						 0x003b0306
-						 0x003c0406
-						 0x003d0506
-						 0x003e0606
-						 0x003f0706
-						 0x00400806
-						 0x00410007
-						 0x00420107
-						 0x00430207
-						 0x00440307
-						 0x00450407
-						 0x00460507
-						 0x00470607
-						 0x00480707
-						 0x00490807
-						 0x004a0008
-						 0x004b0108
-						 0x004c0208
-						 0x004d0308
-						 0x004e0408
-						 0x004f0508
-						 0x00500608
-						 0x00510708
-						 0x00520808 >;
+				linux,keymap = < 0x00000001
+						 0x00010002
+						 0x00020003
+						 0x00030004
+						 0x00040005
+						 0x00050006
+						 0x00060007
+						 0x00070008
+						 0x00080009
+						 0x0100000a
+						 0x0101000c
+						 0x0102000d
+						 0x0103000e
+						 0x0104000f
+						 0x01050010
+						 0x01060011
+						 0x01070012
+						 0x01080013
+						 0x02000014
+						 0x02010015
+						 0x02020016
+						 0x02030017
+						 0x02040018
+						 0x02050019
+						 0x0206001a
+						 0x0207001b
+						 0x0208001c
+						 0x0300001d
+						 0x0301001e
+						 0x0302001f
+						 0x03030020
+						 0x03040021
+						 0x03050022
+						 0x03060023
+						 0x03070024
+						 0x03080025
+						 0x04000026
+						 0x04010027
+						 0x04020028
+						 0x04030029
+						 0x0404002a
+						 0x0405002b
+						 0x0406002c
+						 0x0407002d
+						 0x0408002e
+						 0x0500002f
+						 0x05010030
+						 0x05020031
+						 0x05030032
+						 0x05040033
+						 0x05050034
+						 0x05060035
+						 0x05070036
+						 0x05080037
+						 0x06000038
+						 0x06010039
+						 0x0602003a
+						 0x0603003b
+						 0x0604003c
+						 0x0605003d
+						 0x0606003e
+						 0x0607003f
+						 0x06080040
+						 0x07000041
+						 0x07010042
+						 0x07020043
+						 0x07030044
+						 0x07040045
+						 0x07050046
+						 0x07060047
+						 0x07070048
+						 0x07080049
+						 0x0800004a
+						 0x0801004b
+						 0x0802004c
+						 0x0803004d
+						 0x0804004e
+						 0x0805004f
+						 0x08060050
+						 0x08070051
+						 0x08080052 >;
 			       autorepeat;
 			       st,mode = <0>;
 			       status = "okay";

arch/arm/boot/dts/spear310-evb.dts

@@ -103,11 +103,27 @@ smi: flash@fc000000 {
 			clock-rate=<50000000>;
 
 			flash@f8000000 {
-				label = "m25p64";
-				reg = <0xf8000000 0x800000>;
 				#address-cells = <1>;
 				#size-cells = <1>;
+				reg = <0xf8000000 0x800000>;
 				st,smi-fast-mode;
+
+				partition@0 {
+					label = "xloader";
+					reg = <0x0 0x10000>;
+				};
+				partition@10000 {
+					label = "u-boot";
+					reg = <0x10000 0x40000>;
+				};
+				partition@50000 {
+					label = "linux";
+					reg = <0x50000 0x2c0000>;
+				};
+				partition@310000 {
+					label = "rootfs";
+					reg = <0x310000 0x4f0000>;
+				};
 			};
 		};
 

arch/arm/boot/dts/spear320-evb.dts

@@ -110,6 +110,31 @@ sdhci@70000000 {
 
 		smi: flash@fc000000 {
 			status = "okay";
+			clock-rate=<50000000>;
+
+			flash@f8000000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xf8000000 0x800000>;
+				st,smi-fast-mode;
+
+				partition@0 {
+					label = "xloader";
+					reg = <0x0 0x10000>;
+				};
+				partition@10000 {
+					label = "u-boot";
+					reg = <0x10000 0x40000>;
+				};
+				partition@50000 {
+					label = "linux";
+					reg = <0x50000 0x2c0000>;
+				};
+				partition@310000 {
+					label = "rootfs";
+					reg = <0x310000 0x4f0000>;
+				};
+			};
 		};
 
 		spi0: spi@d0100000 {

arch/arm/boot/dts/spear3xx.dtsi

@@ -139,6 +139,12 @@ wdt@fc880000 {
 				interrupts = <12>;
 				status = "disabled";
 			};
+
+			timer@f0000000 {
+				compatible = "st,spear-timer";
+				reg = <0xf0000000 0x400>;
+				interrupts = <2>;
+			};
 		};
 	};
 };

arch/arm/boot/dts/spear600-evb.dts

@@ -33,6 +33,35 @@ gmac: ethernet@e0800000 {
 			status = "okay";
 		};
 
+		smi: flash@fc000000 {
+			status = "okay";
+			clock-rate=<50000000>;
+
+			flash@f8000000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xf8000000 0x800000>;
+				st,smi-fast-mode;
+
+				partition@0 {
+					label = "xloader";
+					reg = <0x0 0x10000>;
+				};
+				partition@10000 {
+					label = "u-boot";
+					reg = <0x10000 0x40000>;
+				};
+				partition@50000 {
+					label = "linux";
+					reg = <0x50000 0x2c0000>;
+				};
+				partition@310000 {
+					label = "rootfs";
+					reg = <0x310000 0x4f0000>;
+				};
+			};
+		};
+
 		apb {
 			serial@d0000000 {
 				status = "okay";

arch/arm/boot/dts/spear600.dtsi

@@ -177,6 +177,12 @@ i2c@d0200000 {
 				interrupts = <28>;
 				status = "disabled";
 			};
+
+			timer@f0000000 {
+				compatible = "st,spear-timer";
+				reg = <0xf0000000 0x400>;
+				interrupts = <16>;
+			};
 		};
 	};
 };

arch/arm/configs/spear3xx_defconfig

@@ -14,6 +14,9 @@ CONFIG_BINFMT_MISC=y
 CONFIG_NET=y
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
 CONFIG_MTD=y
+CONFIG_MTD_OF_PARTS=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
 CONFIG_MTD_NAND=y
 CONFIG_MTD_NAND_FSMC=y
 CONFIG_BLK_DEV_RAM=y
@@ -73,6 +76,7 @@ CONFIG_MSDOS_FS=m
 CONFIG_VFAT_FS=m
 CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
 CONFIG_TMPFS=y
+CONFIG_JFFS2_FS=y
 CONFIG_NLS_DEFAULT="utf8"
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ASCII=m

arch/arm/configs/spear6xx_defconfig

@@ -8,11 +8,13 @@ CONFIG_MODVERSIONS=y
 CONFIG_PARTITION_ADVANCED=y
 CONFIG_PLAT_SPEAR=y
 CONFIG_ARCH_SPEAR6XX=y
-CONFIG_BOARD_SPEAR600_DT=y
 CONFIG_BINFMT_MISC=y
 CONFIG_NET=y
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
 CONFIG_MTD=y
+CONFIG_MTD_OF_PARTS=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
 CONFIG_MTD_NAND=y
 CONFIG_MTD_NAND_FSMC=y
 CONFIG_BLK_DEV_RAM=y
@@ -64,6 +66,7 @@ CONFIG_MSDOS_FS=m
 CONFIG_VFAT_FS=m
 CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
 CONFIG_TMPFS=y
+CONFIG_JFFS2_FS=y
 CONFIG_NLS_DEFAULT="utf8"
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ASCII=m

arch/arm/mach-spear3xx/include/mach/generic.h

@@ -21,22 +21,13 @@
 #include <asm/mach/time.h>
 #include <asm/mach/map.h>
 
-/* spear3xx declarations */
-/*
- * Each GPT has 2 timer channels
- * Following GPT channels will be used as clock source and clockevent
- */
-#define SPEAR_GPT0_BASE		SPEAR3XX_ML1_TMR_BASE
-#define SPEAR_GPT0_CHAN0_IRQ	SPEAR3XX_IRQ_CPU_GPT1_1
-#define SPEAR_GPT0_CHAN1_IRQ	SPEAR3XX_IRQ_CPU_GPT1_2
-
 /* Add spear3xx family device structure declarations here */
 extern struct sys_timer spear3xx_timer;
 extern struct pl022_ssp_controller pl022_plat_data;
 extern struct pl08x_platform_data pl080_plat_data;
 
 /* Add spear3xx family function declarations here */
-void __init spear_setup_timer(void);
+void __init spear_setup_of_timer(void);
 void __init spear3xx_clk_init(void);
 void __init spear3xx_map_io(void);
 void __init spear3xx_dt_init_irq(void);

arch/arm/mach-spear3xx/include/mach/hardware.h

-/*
- * arch/arm/mach-spear3xx/include/mach/hardware.h
- *
- * Hardware definitions for SPEAr3xx machine family
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __MACH_HARDWARE_H
-#define __MACH_HARDWARE_H
-
-#include <plat/hardware.h>
-#include <mach/spear.h>
-
-#endif /* __MACH_HARDWARE_H */
+/* empty */

arch/arm/mach-spear3xx/include/mach/irqs.h

@@ -14,141 +14,14 @@
 #ifndef __MACH_IRQS_H
 #define __MACH_IRQS_H
 
-/* SPEAr3xx IRQ definitions */
-#define SPEAR3XX_IRQ_HW_ACCEL_MOD_0		0
+/* FIXME: probe all these from DT */
 #define SPEAR3XX_IRQ_INTRCOMM_RAS_ARM		1
-#define SPEAR3XX_IRQ_CPU_GPT1_1			2
-#define SPEAR3XX_IRQ_CPU_GPT1_2			3
-#define SPEAR3XX_IRQ_BASIC_GPT1_1		4
-#define SPEAR3XX_IRQ_BASIC_GPT1_2		5
-#define SPEAR3XX_IRQ_BASIC_GPT2_1		6
-#define SPEAR3XX_IRQ_BASIC_GPT2_2		7
-#define SPEAR3XX_IRQ_BASIC_DMA			8
-#define SPEAR3XX_IRQ_BASIC_SMI			9
-#define SPEAR3XX_IRQ_BASIC_RTC			10
-#define SPEAR3XX_IRQ_BASIC_GPIO			11
-#define SPEAR3XX_IRQ_BASIC_WDT			12
-#define SPEAR3XX_IRQ_DDR_CONTROLLER		13
-#define SPEAR3XX_IRQ_SYS_ERROR			14
-#define SPEAR3XX_IRQ_WAKEUP_RCV			15
-#define SPEAR3XX_IRQ_JPEG			16
-#define SPEAR3XX_IRQ_IRDA			17
-#define SPEAR3XX_IRQ_ADC			18
-#define SPEAR3XX_IRQ_UART			19
-#define SPEAR3XX_IRQ_SSP			20
-#define SPEAR3XX_IRQ_I2C			21
-#define SPEAR3XX_IRQ_MAC_1			22
-#define SPEAR3XX_IRQ_MAC_2			23
-#define SPEAR3XX_IRQ_USB_DEV			24
-#define SPEAR3XX_IRQ_USB_H_OHCI_0		25
-#define SPEAR3XX_IRQ_USB_H_EHCI_0		26
-#define SPEAR3XX_IRQ_USB_H_EHCI_1		SPEAR3XX_IRQ_USB_H_EHCI_0
-#define SPEAR3XX_IRQ_USB_H_OHCI_1		27
 #define SPEAR3XX_IRQ_GEN_RAS_1			28
 #define SPEAR3XX_IRQ_GEN_RAS_2			29
 #define SPEAR3XX_IRQ_GEN_RAS_3			30
-#define SPEAR3XX_IRQ_HW_ACCEL_MOD_1		31
 #define SPEAR3XX_IRQ_VIC_END			32
-
 #define SPEAR3XX_VIRQ_START			SPEAR3XX_IRQ_VIC_END
 
-/* SPEAr300 Virtual irq definitions */
-/* IRQs sharing IRQ_GEN_RAS_1 */
-#define SPEAR300_VIRQ_IT_PERS_S			(SPEAR3XX_VIRQ_START + 0)
-#define SPEAR300_VIRQ_IT_CHANGE_S		(SPEAR3XX_VIRQ_START + 1)
-#define SPEAR300_VIRQ_I2S			(SPEAR3XX_VIRQ_START + 2)
-#define SPEAR300_VIRQ_TDM			(SPEAR3XX_VIRQ_START + 3)
-#define SPEAR300_VIRQ_CAMERA_L			(SPEAR3XX_VIRQ_START + 4)
-#define SPEAR300_VIRQ_CAMERA_F			(SPEAR3XX_VIRQ_START + 5)
-#define SPEAR300_VIRQ_CAMERA_V			(SPEAR3XX_VIRQ_START + 6)
-#define SPEAR300_VIRQ_KEYBOARD			(SPEAR3XX_VIRQ_START + 7)
-#define SPEAR300_VIRQ_GPIO1			(SPEAR3XX_VIRQ_START + 8)
-
-/* IRQs sharing IRQ_GEN_RAS_3 */
-#define SPEAR300_IRQ_CLCD			SPEAR3XX_IRQ_GEN_RAS_3
-
-/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */
-#define SPEAR300_IRQ_SDHCI			SPEAR3XX_IRQ_INTRCOMM_RAS_ARM
-
-/* SPEAr310 Virtual irq definitions */
-/* IRQs sharing IRQ_GEN_RAS_1 */
-#define SPEAR310_VIRQ_SMII0			(SPEAR3XX_VIRQ_START + 0)
-#define SPEAR310_VIRQ_SMII1			(SPEAR3XX_VIRQ_START + 1)
-#define SPEAR310_VIRQ_SMII2			(SPEAR3XX_VIRQ_START + 2)
-#define SPEAR310_VIRQ_SMII3			(SPEAR3XX_VIRQ_START + 3)
-#define SPEAR310_VIRQ_WAKEUP_SMII0		(SPEAR3XX_VIRQ_START + 4)
-#define SPEAR310_VIRQ_WAKEUP_SMII1		(SPEAR3XX_VIRQ_START + 5)
-#define SPEAR310_VIRQ_WAKEUP_SMII2		(SPEAR3XX_VIRQ_START + 6)
-#define SPEAR310_VIRQ_WAKEUP_SMII3		(SPEAR3XX_VIRQ_START + 7)
-
-/* IRQs sharing IRQ_GEN_RAS_2 */
-#define SPEAR310_VIRQ_UART1			(SPEAR3XX_VIRQ_START + 8)
-#define SPEAR310_VIRQ_UART2			(SPEAR3XX_VIRQ_START + 9)
-#define SPEAR310_VIRQ_UART3			(SPEAR3XX_VIRQ_START + 10)
-#define SPEAR310_VIRQ_UART4			(SPEAR3XX_VIRQ_START + 11)
-#define SPEAR310_VIRQ_UART5			(SPEAR3XX_VIRQ_START + 12)
-
-/* IRQs sharing IRQ_GEN_RAS_3 */
-#define SPEAR310_VIRQ_EMI			(SPEAR3XX_VIRQ_START + 13)
-#define SPEAR310_VIRQ_PLGPIO			(SPEAR3XX_VIRQ_START + 14)
-
-/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */
-#define SPEAR310_VIRQ_TDM_HDLC			(SPEAR3XX_VIRQ_START + 15)
-#define SPEAR310_VIRQ_RS485_0			(SPEAR3XX_VIRQ_START + 16)
-#define SPEAR310_VIRQ_RS485_1			(SPEAR3XX_VIRQ_START + 17)
-
-/* SPEAr320 Virtual irq definitions */
-/* IRQs sharing IRQ_GEN_RAS_1 */
-#define SPEAR320_VIRQ_EMI			(SPEAR3XX_VIRQ_START + 0)
-#define SPEAR320_VIRQ_CLCD			(SPEAR3XX_VIRQ_START + 1)
-#define SPEAR320_VIRQ_SPP			(SPEAR3XX_VIRQ_START + 2)
-
-/* IRQs sharing IRQ_GEN_RAS_2 */
-#define SPEAR320_IRQ_SDHCI			SPEAR3XX_IRQ_GEN_RAS_2
-
-/* IRQs sharing IRQ_GEN_RAS_3 */
-#define SPEAR320_VIRQ_PLGPIO			(SPEAR3XX_VIRQ_START + 3)
-#define SPEAR320_VIRQ_I2S_PLAY			(SPEAR3XX_VIRQ_START + 4)
-#define SPEAR320_VIRQ_I2S_REC			(SPEAR3XX_VIRQ_START + 5)
-
-/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */
-#define SPEAR320_VIRQ_CANU			(SPEAR3XX_VIRQ_START + 6)
-#define SPEAR320_VIRQ_CANL			(SPEAR3XX_VIRQ_START + 7)
-#define SPEAR320_VIRQ_UART1			(SPEAR3XX_VIRQ_START + 8)
-#define SPEAR320_VIRQ_UART2			(SPEAR3XX_VIRQ_START + 9)
-#define SPEAR320_VIRQ_SSP1			(SPEAR3XX_VIRQ_START + 10)
-#define SPEAR320_VIRQ_SSP2			(SPEAR3XX_VIRQ_START + 11)
-#define SPEAR320_VIRQ_SMII0			(SPEAR3XX_VIRQ_START + 12)
-#define SPEAR320_VIRQ_MII1_SMII1		(SPEAR3XX_VIRQ_START + 13)
-#define SPEAR320_VIRQ_WAKEUP_SMII0		(SPEAR3XX_VIRQ_START + 14)
-#define SPEAR320_VIRQ_WAKEUP_MII1_SMII1		(SPEAR3XX_VIRQ_START + 15)
-#define SPEAR320_VIRQ_I2C1			(SPEAR3XX_VIRQ_START + 16)
-
-/*
- * GPIO pins virtual irqs
- * Use the lowest number for the GPIO virtual IRQs base on which subarchs
- * we have compiled in
- */
-#if defined(CONFIG_MACH_SPEAR310)
-#define SPEAR3XX_GPIO_INT_BASE			(SPEAR3XX_VIRQ_START + 18)
-#elif defined(CONFIG_MACH_SPEAR320)
-#define SPEAR3XX_GPIO_INT_BASE			(SPEAR3XX_VIRQ_START + 17)
-#else
-#define SPEAR3XX_GPIO_INT_BASE			(SPEAR3XX_VIRQ_START + 9)
-#endif
-
-#define SPEAR300_GPIO1_INT_BASE			(SPEAR3XX_GPIO_INT_BASE + 8)
-#define SPEAR3XX_PLGPIO_COUNT	102
-
-#if defined(CONFIG_MACH_SPEAR310) || defined(CONFIG_MACH_SPEAR320)
-#define SPEAR3XX_PLGPIO_INT_BASE		(SPEAR3XX_GPIO_INT_BASE + 8)
-#define SPEAR3XX_GPIO_INT_END			(SPEAR3XX_PLGPIO_INT_BASE + \
-							SPEAR3XX_PLGPIO_COUNT)
-#else
-#define SPEAR3XX_GPIO_INT_END	(SPEAR300_GPIO1_INT_BASE + 8)
-#endif
-
-#define SPEAR3XX_VIRQ_END	SPEAR3XX_GPIO_INT_END
-#define NR_IRQS			SPEAR3XX_VIRQ_END
+#define NR_IRQS			160
 
 #endif /* __MACH_IRQS_H */

arch/arm/mach-spear3xx/include/mach/misc_regs.h

@@ -14,9 +14,9 @@
 #ifndef __MACH_MISC_REGS_H
 #define __MACH_MISC_REGS_H
 
-#include <mach/hardware.h>
 #include <mach/spear.h>
 
 #define MISC_BASE		IOMEM(VA_SPEAR3XX_ICM3_MISC_REG_BASE)
+#define DMA_CHN_CFG		(MISC_BASE + 0x0A0)
 
 #endif /* __MACH_MISC_REGS_H */

arch/arm/mach-spear3xx/include/mach/spear.h

@@ -15,61 +15,26 @@
 #define __MACH_SPEAR3XX_H
 
 #include <asm/memory.h>
-#include <mach/spear300.h>
-#include <mach/spear310.h>
-#include <mach/spear320.h>
-
-#define SPEAR3XX_ML_SDRAM_BASE		UL(0x00000000)
-
-#define SPEAR3XX_ICM9_BASE		UL(0xC0000000)
 
 /* ICM1 - Low speed connection */
 #define SPEAR3XX_ICM1_2_BASE		UL(0xD0000000)
 #define VA_SPEAR3XX_ICM1_2_BASE		UL(0xFD000000)
 #define SPEAR3XX_ICM1_UART_BASE		UL(0xD0000000)
 #define VA_SPEAR3XX_ICM1_UART_BASE	(VA_SPEAR3XX_ICM1_2_BASE | SPEAR3XX_ICM1_UART_BASE)
-#define SPEAR3XX_ICM1_ADC_BASE		UL(0xD0080000)
 #define SPEAR3XX_ICM1_SSP_BASE		UL(0xD0100000)
-#define SPEAR3XX_ICM1_I2C_BASE		UL(0xD0180000)
-#define SPEAR3XX_ICM1_JPEG_BASE		UL(0xD0800000)
-#define SPEAR3XX_ICM1_IRDA_BASE		UL(0xD1000000)
-#define SPEAR3XX_ICM1_SRAM_BASE		UL(0xD2800000)
-
-/* ICM2 - Application Subsystem */
-#define SPEAR3XX_ICM2_HWACCEL0_BASE	UL(0xD8800000)
-#define SPEAR3XX_ICM2_HWACCEL1_BASE	UL(0xD9000000)
-
-/* ICM4 - High Speed Connection */
-#define SPEAR3XX_ICM4_BASE		UL(0xE0000000)
-#define SPEAR3XX_ICM4_MII_BASE		UL(0xE0800000)
-#define SPEAR3XX_ICM4_USBD_FIFO_BASE	UL(0xE1000000)
-#define SPEAR3XX_ICM4_USBD_CSR_BASE	UL(0xE1100000)
-#define SPEAR3XX_ICM4_USBD_PLDT_BASE	UL(0xE1200000)
-#define SPEAR3XX_ICM4_USB_EHCI0_1_BASE	UL(0xE1800000)
-#define SPEAR3XX_ICM4_USB_OHCI0_BASE	UL(0xE1900000)
-#define SPEAR3XX_ICM4_USB_OHCI1_BASE	UL(0xE2100000)
-#define SPEAR3XX_ICM4_USB_ARB_BASE	UL(0xE2800000)
 
 /* ML1 - Multi Layer CPU Subsystem */
 #define SPEAR3XX_ICM3_ML1_2_BASE	UL(0xF0000000)
-#define SPEAR3XX_ML1_TMR_BASE		UL(0xF0000000)
-#define SPEAR3XX_ML1_VIC_BASE		UL(0xF1100000)
+#define VA_SPEAR6XX_ML_CPU_BASE		UL(0xF0000000)
 
 /* ICM3 - Basic Subsystem */
-#define SPEAR3XX_ICM3_SMEM_BASE		UL(0xF8000000)
 #define SPEAR3XX_ICM3_SMI_CTRL_BASE	UL(0xFC000000)
 #define VA_SPEAR3XX_ICM3_SMI_CTRL_BASE	UL(0xFC000000)
 #define SPEAR3XX_ICM3_DMA_BASE		UL(0xFC400000)
-#define SPEAR3XX_ICM3_SDRAM_CTRL_BASE	UL(0xFC600000)
-#define SPEAR3XX_ICM3_TMR0_BASE		UL(0xFC800000)
-#define SPEAR3XX_ICM3_WDT_BASE		UL(0xFC880000)
-#define SPEAR3XX_ICM3_RTC_BASE		UL(0xFC900000)
-#define SPEAR3XX_ICM3_GPIO_BASE		UL(0xFC980000)
 #define SPEAR3XX_ICM3_SYS_CTRL_BASE	UL(0xFCA00000)
 #define VA_SPEAR3XX_ICM3_SYS_CTRL_BASE	(VA_SPEAR3XX_ICM3_SMI_CTRL_BASE | SPEAR3XX_ICM3_SYS_CTRL_BASE)
 #define SPEAR3XX_ICM3_MISC_REG_BASE	UL(0xFCA80000)
 #define VA_SPEAR3XX_ICM3_MISC_REG_BASE	(VA_SPEAR3XX_ICM3_SMI_CTRL_BASE | SPEAR3XX_ICM3_MISC_REG_BASE)
-#define SPEAR3XX_ICM3_TMR1_BASE		UL(0xFCB00000)
 
 /* Debug uart for linux, will be used for debug and uncompress messages */
 #define SPEAR_DBG_UART_BASE		SPEAR3XX_ICM1_UART_BASE

arch/arm/mach-spear3xx/include/mach/spear300.h

-/*
- * arch/arm/mach-spear3xx/include/mach/spear300.h
- *
- * SPEAr300 Machine specific definition
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifdef	CONFIG_MACH_SPEAR300
-
-#ifndef __MACH_SPEAR300_H
-#define __MACH_SPEAR300_H
-
-/* Base address of various IPs */
-#define SPEAR300_TELECOM_BASE		UL(0x50000000)
-
-/* Interrupt registers offsets and masks */
-#define SPEAR300_INT_ENB_MASK_REG	0x54
-#define SPEAR300_INT_STS_MASK_REG	0x58
-#define SPEAR300_IT_PERS_S_IRQ_MASK	(1 << 0)
-#define SPEAR300_IT_CHANGE_S_IRQ_MASK	(1 << 1)
-#define SPEAR300_I2S_IRQ_MASK		(1 << 2)
-#define SPEAR300_TDM_IRQ_MASK		(1 << 3)
-#define SPEAR300_CAMERA_L_IRQ_MASK	(1 << 4)
-#define SPEAR300_CAMERA_F_IRQ_MASK	(1 << 5)
-#define SPEAR300_CAMERA_V_IRQ_MASK	(1 << 6)
-#define SPEAR300_KEYBOARD_IRQ_MASK	(1 << 7)
-#define SPEAR300_GPIO1_IRQ_MASK		(1 << 8)
-
-#define SPEAR300_SHIRQ_RAS1_MASK	0x1FF
-
-#define SPEAR300_CLCD_BASE		UL(0x60000000)
-#define SPEAR300_SDHCI_BASE		UL(0x70000000)
-#define SPEAR300_NAND_0_BASE		UL(0x80000000)
-#define SPEAR300_NAND_1_BASE		UL(0x84000000)
-#define SPEAR300_NAND_2_BASE		UL(0x88000000)
-#define SPEAR300_NAND_3_BASE		UL(0x8c000000)
-#define SPEAR300_NOR_0_BASE		UL(0x90000000)
-#define SPEAR300_NOR_1_BASE		UL(0x91000000)
-#define SPEAR300_NOR_2_BASE		UL(0x92000000)
-#define SPEAR300_NOR_3_BASE		UL(0x93000000)
-#define SPEAR300_FSMC_BASE		UL(0x94000000)
-#define SPEAR300_SOC_CONFIG_BASE	UL(0x99000000)
-#define SPEAR300_KEYBOARD_BASE		UL(0xA0000000)
-#define SPEAR300_GPIO_BASE		UL(0xA9000000)
-
-#endif /* __MACH_SPEAR300_H */
-
-#endif /* CONFIG_MACH_SPEAR300 */

arch/arm/mach-spear3xx/include/mach/spear310.h

-/*
- * arch/arm/mach-spear3xx/include/mach/spear310.h
- *
- * SPEAr310 Machine specific definition
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifdef	CONFIG_MACH_SPEAR310
-
-#ifndef __MACH_SPEAR310_H
-#define __MACH_SPEAR310_H
-
-#define SPEAR310_NAND_BASE		UL(0x40000000)
-#define SPEAR310_FSMC_BASE		UL(0x44000000)
-#define SPEAR310_UART1_BASE		UL(0xB2000000)
-#define SPEAR310_UART2_BASE		UL(0xB2080000)
-#define SPEAR310_UART3_BASE		UL(0xB2100000)
-#define SPEAR310_UART4_BASE		UL(0xB2180000)
-#define SPEAR310_UART5_BASE		UL(0xB2200000)
-#define SPEAR310_HDLC_BASE		UL(0xB2800000)
-#define SPEAR310_RS485_0_BASE		UL(0xB3000000)
-#define SPEAR310_RS485_1_BASE		UL(0xB3800000)
-#define SPEAR310_SOC_CONFIG_BASE	UL(0xB4000000)
-
-/* Interrupt registers offsets and masks */
-#define SPEAR310_INT_STS_MASK_REG	0x04
-#define SPEAR310_SMII0_IRQ_MASK		(1 << 0)
-#define SPEAR310_SMII1_IRQ_MASK		(1 << 1)
-#define SPEAR310_SMII2_IRQ_MASK		(1 << 2)
-#define SPEAR310_SMII3_IRQ_MASK		(1 << 3)
-#define SPEAR310_WAKEUP_SMII0_IRQ_MASK	(1 << 4)
-#define SPEAR310_WAKEUP_SMII1_IRQ_MASK	(1 << 5)
-#define SPEAR310_WAKEUP_SMII2_IRQ_MASK	(1 << 6)
-#define SPEAR310_WAKEUP_SMII3_IRQ_MASK	(1 << 7)
-#define SPEAR310_UART1_IRQ_MASK		(1 << 8)
-#define SPEAR310_UART2_IRQ_MASK		(1 << 9)
-#define SPEAR310_UART3_IRQ_MASK		(1 << 10)
-#define SPEAR310_UART4_IRQ_MASK		(1 << 11)
-#define SPEAR310_UART5_IRQ_MASK		(1 << 12)
-#define SPEAR310_EMI_IRQ_MASK		(1 << 13)
-#define SPEAR310_TDM_HDLC_IRQ_MASK	(1 << 14)
-#define SPEAR310_RS485_0_IRQ_MASK	(1 << 15)
-#define SPEAR310_RS485_1_IRQ_MASK	(1 << 16)
-
-#define SPEAR310_SHIRQ_RAS1_MASK	0x000FF
-#define SPEAR310_SHIRQ_RAS2_MASK	0x01F00
-#define SPEAR310_SHIRQ_RAS3_MASK	0x02000
-#define SPEAR310_SHIRQ_INTRCOMM_RAS_MASK	0x1C000
-
-#endif /* __MACH_SPEAR310_H */
-
-#endif /* CONFIG_MACH_SPEAR310 */

arch/arm/mach-spear3xx/include/mach/spear320.h

-/*
- * arch/arm/mach-spear3xx/include/mach/spear320.h
- *
- * SPEAr320 Machine specific definition
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifdef	CONFIG_MACH_SPEAR320
-
-#ifndef __MACH_SPEAR320_H
-#define __MACH_SPEAR320_H
-
-#define SPEAR320_EMI_CTRL_BASE		UL(0x40000000)
-#define SPEAR320_FSMC_BASE		UL(0x4C000000)
-#define SPEAR320_NAND_BASE		UL(0x50000000)
-#define SPEAR320_I2S_BASE		UL(0x60000000)
-#define SPEAR320_SDHCI_BASE		UL(0x70000000)
-#define SPEAR320_CLCD_BASE		UL(0x90000000)
-#define SPEAR320_PAR_PORT_BASE		UL(0xA0000000)
-#define SPEAR320_CAN0_BASE		UL(0xA1000000)
-#define SPEAR320_CAN1_BASE		UL(0xA2000000)
-#define SPEAR320_UART1_BASE		UL(0xA3000000)
-#define SPEAR320_UART2_BASE		UL(0xA4000000)
-#define SPEAR320_SSP0_BASE		UL(0xA5000000)
-#define SPEAR320_SSP1_BASE		UL(0xA6000000)
-#define SPEAR320_I2C_BASE		UL(0xA7000000)
-#define SPEAR320_PWM_BASE		UL(0xA8000000)
-#define SPEAR320_SMII0_BASE		UL(0xAA000000)
-#define SPEAR320_SMII1_BASE		UL(0xAB000000)
-#define SPEAR320_SOC_CONFIG_BASE	UL(0xB3000000)
-
-/* Interrupt registers offsets and masks */
-#define SPEAR320_INT_STS_MASK_REG		0x04
-#define SPEAR320_INT_CLR_MASK_REG		0x04
-#define SPEAR320_INT_ENB_MASK_REG		0x08
-#define SPEAR320_GPIO_IRQ_MASK			(1 << 0)
-#define SPEAR320_I2S_PLAY_IRQ_MASK		(1 << 1)
-#define SPEAR320_I2S_REC_IRQ_MASK		(1 << 2)
-#define SPEAR320_EMI_IRQ_MASK			(1 << 7)
-#define SPEAR320_CLCD_IRQ_MASK			(1 << 8)
-#define SPEAR320_SPP_IRQ_MASK			(1 << 9)
-#define SPEAR320_SDHCI_IRQ_MASK			(1 << 10)
-#define SPEAR320_CAN_U_IRQ_MASK			(1 << 11)
-#define SPEAR320_CAN_L_IRQ_MASK			(1 << 12)
-#define SPEAR320_UART1_IRQ_MASK			(1 << 13)
-#define SPEAR320_UART2_IRQ_MASK			(1 << 14)
-#define SPEAR320_SSP1_IRQ_MASK			(1 << 15)
-#define SPEAR320_SSP2_IRQ_MASK			(1 << 16)
-#define SPEAR320_SMII0_IRQ_MASK			(1 << 17)
-#define SPEAR320_MII1_SMII1_IRQ_MASK		(1 << 18)
-#define SPEAR320_WAKEUP_SMII0_IRQ_MASK		(1 << 19)
-#define SPEAR320_WAKEUP_MII1_SMII1_IRQ_MASK	(1 << 20)
-#define SPEAR320_I2C1_IRQ_MASK			(1 << 21)
-
-#define SPEAR320_SHIRQ_RAS1_MASK		0x000380
-#define SPEAR320_SHIRQ_RAS3_MASK		0x000007
-#define SPEAR320_SHIRQ_INTRCOMM_RAS_MASK	0x3FF800
-
-#endif /* __MACH_SPEAR320_H */
-
-#endif /* CONFIG_MACH_SPEAR320 */

arch/arm/mach-spear3xx/spear300.c

@@ -19,7 +19,46 @@
 #include <asm/mach/arch.h>
 #include <plat/shirq.h>
 #include <mach/generic.h>
-#include <mach/hardware.h>
+#include <mach/spear.h>
+
+/* Base address of various IPs */
+#define SPEAR300_TELECOM_BASE		UL(0x50000000)
+
+/* Interrupt registers offsets and masks */
+#define SPEAR300_INT_ENB_MASK_REG	0x54
+#define SPEAR300_INT_STS_MASK_REG	0x58
+#define SPEAR300_IT_PERS_S_IRQ_MASK	(1 << 0)
+#define SPEAR300_IT_CHANGE_S_IRQ_MASK	(1 << 1)
+#define SPEAR300_I2S_IRQ_MASK		(1 << 2)
+#define SPEAR300_TDM_IRQ_MASK		(1 << 3)
+#define SPEAR300_CAMERA_L_IRQ_MASK	(1 << 4)
+#define SPEAR300_CAMERA_F_IRQ_MASK	(1 << 5)
+#define SPEAR300_CAMERA_V_IRQ_MASK	(1 << 6)
+#define SPEAR300_KEYBOARD_IRQ_MASK	(1 << 7)
+#define SPEAR300_GPIO1_IRQ_MASK		(1 << 8)
+
+#define SPEAR300_SHIRQ_RAS1_MASK	0x1FF
+
+#define SPEAR300_SOC_CONFIG_BASE	UL(0x99000000)
+
+
+/* SPEAr300 Virtual irq definitions */
+/* IRQs sharing IRQ_GEN_RAS_1 */
+#define SPEAR300_VIRQ_IT_PERS_S			(SPEAR3XX_VIRQ_START + 0)
+#define SPEAR300_VIRQ_IT_CHANGE_S		(SPEAR3XX_VIRQ_START + 1)
+#define SPEAR300_VIRQ_I2S			(SPEAR3XX_VIRQ_START + 2)
+#define SPEAR300_VIRQ_TDM			(SPEAR3XX_VIRQ_START + 3)
+#define SPEAR300_VIRQ_CAMERA_L			(SPEAR3XX_VIRQ_START + 4)
+#define SPEAR300_VIRQ_CAMERA_F			(SPEAR3XX_VIRQ_START + 5)
+#define SPEAR300_VIRQ_CAMERA_V			(SPEAR3XX_VIRQ_START + 6)
+#define SPEAR300_VIRQ_KEYBOARD			(SPEAR3XX_VIRQ_START + 7)
+#define SPEAR300_VIRQ_GPIO1			(SPEAR3XX_VIRQ_START + 8)
+
+/* IRQs sharing IRQ_GEN_RAS_3 */
+#define SPEAR300_IRQ_CLCD			SPEAR3XX_IRQ_GEN_RAS_3
+
+/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */
+#define SPEAR300_IRQ_SDHCI			SPEAR3XX_IRQ_INTRCOMM_RAS_ARM
 
 /* spear3xx shared irq */
 static struct shirq_dev_config shirq_ras1_config[] = {
@@ -298,7 +337,6 @@ static const char * const spear300_dt_board_compat[] = {
 static void __init spear300_map_io(void)
 {
 	spear3xx_map_io();
-	spear300_clk_init();
 }
 
 DT_MACHINE_START(SPEAR300_DT, "ST SPEAr300 SoC with Flattened Device Tree")

arch/arm/mach-spear3xx/spear310.c

@@ -20,7 +20,67 @@
 #include <asm/mach/arch.h>
 #include <plat/shirq.h>
 #include <mach/generic.h>
-#include <mach/hardware.h>
+#include <mach/spear.h>
+
+#define SPEAR310_UART1_BASE		UL(0xB2000000)
+#define SPEAR310_UART2_BASE		UL(0xB2080000)
+#define SPEAR310_UART3_BASE		UL(0xB2100000)
+#define SPEAR310_UART4_BASE		UL(0xB2180000)
+#define SPEAR310_UART5_BASE		UL(0xB2200000)
+#define SPEAR310_SOC_CONFIG_BASE	UL(0xB4000000)
+
+/* Interrupt registers offsets and masks */
+#define SPEAR310_INT_STS_MASK_REG	0x04
+#define SPEAR310_SMII0_IRQ_MASK		(1 << 0)
+#define SPEAR310_SMII1_IRQ_MASK		(1 << 1)
+#define SPEAR310_SMII2_IRQ_MASK		(1 << 2)
+#define SPEAR310_SMII3_IRQ_MASK		(1 << 3)
+#define SPEAR310_WAKEUP_SMII0_IRQ_MASK	(1 << 4)
+#define SPEAR310_WAKEUP_SMII1_IRQ_MASK	(1 << 5)
+#define SPEAR310_WAKEUP_SMII2_IRQ_MASK	(1 << 6)
+#define SPEAR310_WAKEUP_SMII3_IRQ_MASK	(1 << 7)
+#define SPEAR310_UART1_IRQ_MASK		(1 << 8)
+#define SPEAR310_UART2_IRQ_MASK		(1 << 9)
+#define SPEAR310_UART3_IRQ_MASK		(1 << 10)
+#define SPEAR310_UART4_IRQ_MASK		(1 << 11)
+#define SPEAR310_UART5_IRQ_MASK		(1 << 12)
+#define SPEAR310_EMI_IRQ_MASK		(1 << 13)
+#define SPEAR310_TDM_HDLC_IRQ_MASK	(1 << 14)
+#define SPEAR310_RS485_0_IRQ_MASK	(1 << 15)
+#define SPEAR310_RS485_1_IRQ_MASK	(1 << 16)
+
+#define SPEAR310_SHIRQ_RAS1_MASK	0x000FF
+#define SPEAR310_SHIRQ_RAS2_MASK	0x01F00
+#define SPEAR310_SHIRQ_RAS3_MASK	0x02000
+#define SPEAR310_SHIRQ_INTRCOMM_RAS_MASK	0x1C000
+
+/* SPEAr310 Virtual irq definitions */
+/* IRQs sharing IRQ_GEN_RAS_1 */
+#define SPEAR310_VIRQ_SMII0			(SPEAR3XX_VIRQ_START + 0)
+#define SPEAR310_VIRQ_SMII1			(SPEAR3XX_VIRQ_START + 1)
+#define SPEAR310_VIRQ_SMII2			(SPEAR3XX_VIRQ_START + 2)
+#define SPEAR310_VIRQ_SMII3			(SPEAR3XX_VIRQ_START + 3)
+#define SPEAR310_VIRQ_WAKEUP_SMII0		(SPEAR3XX_VIRQ_START + 4)
+#define SPEAR310_VIRQ_WAKEUP_SMII1		(SPEAR3XX_VIRQ_START + 5)
+#define SPEAR310_VIRQ_WAKEUP_SMII2		(SPEAR3XX_VIRQ_START + 6)
+#define SPEAR310_VIRQ_WAKEUP_SMII3		(SPEAR3XX_VIRQ_START + 7)
+
+/* IRQs sharing IRQ_GEN_RAS_2 */
+#define SPEAR310_VIRQ_UART1			(SPEAR3XX_VIRQ_START + 8)
+#define SPEAR310_VIRQ_UART2			(SPEAR3XX_VIRQ_START + 9)
+#define SPEAR310_VIRQ_UART3			(SPEAR3XX_VIRQ_START + 10)
+#define SPEAR310_VIRQ_UART4			(SPEAR3XX_VIRQ_START + 11)
+#define SPEAR310_VIRQ_UART5			(SPEAR3XX_VIRQ_START + 12)
+
+/* IRQs sharing IRQ_GEN_RAS_3 */
+#define SPEAR310_VIRQ_EMI			(SPEAR3XX_VIRQ_START + 13)
+#define SPEAR310_VIRQ_PLGPIO			(SPEAR3XX_VIRQ_START + 14)
+
+/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */
+#define SPEAR310_VIRQ_TDM_HDLC			(SPEAR3XX_VIRQ_START + 15)
+#define SPEAR310_VIRQ_RS485_0			(SPEAR3XX_VIRQ_START + 16)
+#define SPEAR310_VIRQ_RS485_1			(SPEAR3XX_VIRQ_START + 17)
+
 
 /* spear3xx shared irq */
 static struct shirq_dev_config shirq_ras1_config[] = {
@@ -418,7 +478,6 @@ static const char * const spear310_dt_board_compat[] = {
 static void __init spear310_map_io(void)
 {
 	spear3xx_map_io();
-	spear310_clk_init();
 }
 
 DT_MACHINE_START(SPEAR310_DT, "ST SPEAr310 SoC with Flattened Device Tree")

arch/arm/mach-spear3xx/spear320.c

@@ -21,9 +21,67 @@
 #include <asm/mach/arch.h>
 #include <plat/shirq.h>
 #include <mach/generic.h>
-#include <mach/hardware.h>
 #include <mach/spear.h>
 
+#define SPEAR320_UART1_BASE		UL(0xA3000000)
+#define SPEAR320_UART2_BASE		UL(0xA4000000)
+#define SPEAR320_SSP0_BASE		UL(0xA5000000)
+#define SPEAR320_SSP1_BASE		UL(0xA6000000)
+
+/* Interrupt registers offsets and masks */
+#define SPEAR320_INT_STS_MASK_REG		0x04
+#define SPEAR320_INT_CLR_MASK_REG		0x04
+#define SPEAR320_INT_ENB_MASK_REG		0x08
+#define SPEAR320_GPIO_IRQ_MASK			(1 << 0)
+#define SPEAR320_I2S_PLAY_IRQ_MASK		(1 << 1)
+#define SPEAR320_I2S_REC_IRQ_MASK		(1 << 2)
+#define SPEAR320_EMI_IRQ_MASK			(1 << 7)
+#define SPEAR320_CLCD_IRQ_MASK			(1 << 8)
+#define SPEAR320_SPP_IRQ_MASK			(1 << 9)
+#define SPEAR320_SDHCI_IRQ_MASK			(1 << 10)
+#define SPEAR320_CAN_U_IRQ_MASK			(1 << 11)
+#define SPEAR320_CAN_L_IRQ_MASK			(1 << 12)
+#define SPEAR320_UART1_IRQ_MASK			(1 << 13)
+#define SPEAR320_UART2_IRQ_MASK			(1 << 14)
+#define SPEAR320_SSP1_IRQ_MASK			(1 << 15)
+#define SPEAR320_SSP2_IRQ_MASK			(1 << 16)
+#define SPEAR320_SMII0_IRQ_MASK			(1 << 17)
+#define SPEAR320_MII1_SMII1_IRQ_MASK		(1 << 18)
+#define SPEAR320_WAKEUP_SMII0_IRQ_MASK		(1 << 19)
+#define SPEAR320_WAKEUP_MII1_SMII1_IRQ_MASK	(1 << 20)
+#define SPEAR320_I2C1_IRQ_MASK			(1 << 21)
+
+#define SPEAR320_SHIRQ_RAS1_MASK		0x000380
+#define SPEAR320_SHIRQ_RAS3_MASK		0x000007
+#define SPEAR320_SHIRQ_INTRCOMM_RAS_MASK	0x3FF800
+
+/* SPEAr320 Virtual irq definitions */
+/* IRQs sharing IRQ_GEN_RAS_1 */
+#define SPEAR320_VIRQ_EMI			(SPEAR3XX_VIRQ_START + 0)
+#define SPEAR320_VIRQ_CLCD			(SPEAR3XX_VIRQ_START + 1)
+#define SPEAR320_VIRQ_SPP			(SPEAR3XX_VIRQ_START + 2)
+
+/* IRQs sharing IRQ_GEN_RAS_2 */
+#define SPEAR320_IRQ_SDHCI			SPEAR3XX_IRQ_GEN_RAS_2
+
+/* IRQs sharing IRQ_GEN_RAS_3 */
+#define SPEAR320_VIRQ_PLGPIO			(SPEAR3XX_VIRQ_START + 3)
+#define SPEAR320_VIRQ_I2S_PLAY			(SPEAR3XX_VIRQ_START + 4)
+#define SPEAR320_VIRQ_I2S_REC			(SPEAR3XX_VIRQ_START + 5)
+
+/* IRQs sharing IRQ_INTRCOMM_RAS_ARM */
+#define SPEAR320_VIRQ_CANU			(SPEAR3XX_VIRQ_START + 6)
+#define SPEAR320_VIRQ_CANL			(SPEAR3XX_VIRQ_START + 7)
+#define SPEAR320_VIRQ_UART1			(SPEAR3XX_VIRQ_START + 8)
+#define SPEAR320_VIRQ_UART2			(SPEAR3XX_VIRQ_START + 9)
+#define SPEAR320_VIRQ_SSP1			(SPEAR3XX_VIRQ_START + 10)
+#define SPEAR320_VIRQ_SSP2			(SPEAR3XX_VIRQ_START + 11)
+#define SPEAR320_VIRQ_SMII0			(SPEAR3XX_VIRQ_START + 12)
+#define SPEAR320_VIRQ_MII1_SMII1		(SPEAR3XX_VIRQ_START + 13)
+#define SPEAR320_VIRQ_WAKEUP_SMII0		(SPEAR3XX_VIRQ_START + 14)
+#define SPEAR320_VIRQ_WAKEUP_MII1_SMII1		(SPEAR3XX_VIRQ_START + 15)
+#define SPEAR320_VIRQ_I2C1			(SPEAR3XX_VIRQ_START + 16)
+
 /* spear3xx shared irq */
 static struct shirq_dev_config shirq_ras1_config[] = {
 	{
@@ -422,10 +480,19 @@ static const char * const spear320_dt_board_compat[] = {
 	NULL,
 };
 
+struct map_desc spear320_io_desc[] __initdata = {
+	{
+		.virtual	= VA_SPEAR320_SOC_CONFIG_BASE,
+		.pfn		= __phys_to_pfn(SPEAR320_SOC_CONFIG_BASE),
+		.length		= SZ_16M,
+		.type		= MT_DEVICE
+	},
+};
+
 static void __init spear320_map_io(void)
 {
+	iotable_init(spear320_io_desc, ARRAY_SIZE(spear320_io_desc));
 	spear3xx_map_io();
-	spear320_clk_init();
 }
 
 DT_MACHINE_START(SPEAR320_DT, "ST SPEAr320 SoC with Flattened Device Tree")

arch/arm/mach-spear3xx/spear3xx.c

@@ -21,7 +21,7 @@
 #include <asm/hardware/vic.h>
 #include <plat/pl080.h>
 #include <mach/generic.h>
-#include <mach/hardware.h>
+#include <mach/spear.h>
 
 /* ssp device registration */
 struct pl022_ssp_controller pl022_plat_data = {
@@ -111,7 +111,7 @@ static void __init spear3xx_timer_init(void)
 	clk_put(gpt_clk);
 	clk_put(pclk);
 
-	spear_setup_timer();
+	spear_setup_of_timer();
 }
 
 struct sys_timer spear3xx_timer = {

arch/arm/mach-spear6xx/include/mach/generic.h

@@ -15,34 +15,9 @@
 #define __MACH_GENERIC_H
 
 #include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/amba/bus.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-
-/*
- * Each GPT has 2 timer channels
- * Following GPT channels will be used as clock source and clockevent
- */
-#define SPEAR_GPT0_BASE		SPEAR6XX_CPU_TMR_BASE
-#define SPEAR_GPT0_CHAN0_IRQ	IRQ_CPU_GPT1_1
-#define SPEAR_GPT0_CHAN1_IRQ	IRQ_CPU_GPT1_2
-
-/* Add spear6xx family device structure declarations here */
-extern struct amba_device gpio_device[];
-extern struct amba_device uart_device[];
-extern struct sys_timer spear6xx_timer;
-
-/* Add spear6xx family function declarations here */
-void __init spear_setup_timer(void);
-void __init spear6xx_map_io(void);
-void __init spear6xx_init_irq(void);
-void __init spear6xx_init(void);
-void __init spear600_init(void);
-void __init spear6xx_clk_init(void);
 
+void __init spear_setup_of_timer(void);
 void spear_restart(char, const char *);
-
-/* Add spear600 machine device structure declarations here */
+void __init spear6xx_clk_init(void);
 
 #endif /* __MACH_GENERIC_H */

arch/arm/mach-spear6xx/include/mach/hardware.h

-/*
- * arch/arm/mach-spear6xx/include/mach/hardware.h
- *
- * Hardware definitions for SPEAr6xx machine family
- *
- * Copyright (C) 2009 ST Microelectronics
- * Rajeev Kumar<rajeev-dlh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __MACH_HARDWARE_H
-#define __MACH_HARDWARE_H
-
-#include <plat/hardware.h>
-#include <mach/spear.h>
-
-/* Vitual to physical translation of statically mapped space */
-#define IO_ADDRESS(x)		(x | 0xF0000000)
-
-#endif /* __MACH_HARDWARE_H */
+/* empty */

arch/arm/mach-spear6xx/include/mach/irqs.h

@@ -16,82 +16,10 @@
 
 /* IRQ definitions */
 /* VIC 1 */
-#define IRQ_INTRCOMM_SW_IRQ			0
-#define IRQ_INTRCOMM_CPU_1			1
-#define IRQ_INTRCOMM_CPU_2			2
-#define IRQ_INTRCOMM_RAS2A11_1			3
-#define IRQ_INTRCOMM_RAS2A11_2			4
-#define IRQ_INTRCOMM_RAS2A12_1			5
-#define IRQ_INTRCOMM_RAS2A12_2			6
-#define IRQ_GEN_RAS_0				7
-#define IRQ_GEN_RAS_1				8
-#define IRQ_GEN_RAS_2				9
-#define IRQ_GEN_RAS_3				10
-#define IRQ_GEN_RAS_4				11
-#define IRQ_GEN_RAS_5				12
-#define IRQ_GEN_RAS_6				13
-#define IRQ_GEN_RAS_7				14
-#define IRQ_GEN_RAS_8				15
-#define IRQ_CPU_GPT1_1				16
-#define IRQ_CPU_GPT1_2				17
-#define IRQ_LOCAL_GPIO				18
-#define IRQ_PLL_UNLOCK				19
-#define IRQ_JPEG				20
-#define IRQ_FSMC				21
-#define IRQ_IRDA				22
-#define IRQ_RESERVED				23
-#define IRQ_UART_0				24
-#define IRQ_UART_1				25
-#define IRQ_SSP_1				26
-#define IRQ_SSP_2				27
-#define IRQ_I2C					28
-#define IRQ_GEN_RAS_9				29
-#define IRQ_GEN_RAS_10				30
-#define IRQ_GEN_RAS_11				31
-
-/* VIC 2 */
-#define IRQ_APPL_GPT1_1				32
-#define IRQ_APPL_GPT1_2				33
-#define IRQ_APPL_GPT2_1				34
-#define IRQ_APPL_GPT2_2				35
-#define IRQ_APPL_GPIO				36
-#define IRQ_APPL_SSP				37
-#define IRQ_APPL_ADC				38
-#define IRQ_APPL_RESERVED			39
-#define IRQ_AHB_EXP_MASTER			40
-#define IRQ_DDR_CONTROLLER			41
-#define IRQ_BASIC_DMA				42
-#define IRQ_BASIC_RESERVED1			43
-#define IRQ_BASIC_SMI				44
-#define IRQ_BASIC_CLCD				45
-#define IRQ_EXP_AHB_1				46
-#define IRQ_EXP_AHB_2				47
-#define IRQ_BASIC_GPT1_1			48
-#define IRQ_BASIC_GPT1_2			49
-#define IRQ_BASIC_RTC				50
-#define IRQ_BASIC_GPIO				51
-#define IRQ_BASIC_WDT				52
-#define IRQ_BASIC_RESERVED			53
-#define IRQ_AHB_EXP_SLAVE			54
-#define IRQ_GMAC_1				55
-#define IRQ_GMAC_2				56
-#define IRQ_USB_DEV				57
-#define IRQ_USB_H_OHCI_0			58
-#define IRQ_USB_H_EHCI_0			59
-#define IRQ_USB_H_OHCI_1			60
-#define IRQ_USB_H_EHCI_1			61
-#define IRQ_EXP_AHB_3				62
-#define IRQ_EXP_AHB_4				63
-
 #define IRQ_VIC_END				64
 
 /* GPIO pins virtual irqs */
-#define SPEAR_GPIO_INT_BASE	IRQ_VIC_END
-#define SPEAR_GPIO0_INT_BASE	SPEAR_GPIO_INT_BASE
-#define SPEAR_GPIO1_INT_BASE	(SPEAR_GPIO0_INT_BASE + 8)
-#define SPEAR_GPIO2_INT_BASE	(SPEAR_GPIO1_INT_BASE + 8)
-#define SPEAR_GPIO_INT_END	(SPEAR_GPIO2_INT_BASE + 8)
-#define VIRTUAL_IRQS		(SPEAR_GPIO_INT_END - IRQ_VIC_END)
-#define NR_IRQS			(IRQ_VIC_END + VIRTUAL_IRQS)
+#define VIRTUAL_IRQS				24
+#define NR_IRQS					(IRQ_VIC_END + VIRTUAL_IRQS)
 
 #endif	/* __MACH_IRQS_H */

arch/arm/mach-spear6xx/include/mach/misc_regs.h

@@ -14,9 +14,9 @@
 #ifndef __MACH_MISC_REGS_H
 #define __MACH_MISC_REGS_H
 
-#include <mach/hardware.h>
 #include <mach/spear.h>
 
 #define MISC_BASE		IOMEM(VA_SPEAR6XX_ICM3_MISC_REG_BASE)
+#define DMA_CHN_CFG		(MISC_BASE + 0x0A0)
 
 #endif /* __MACH_MISC_REGS_H */

arch/arm/mach-spear6xx/include/mach/spear.h

@@ -15,69 +15,25 @@
 #define __MACH_SPEAR6XX_H
 
 #include <asm/memory.h>
-#include <mach/spear600.h>
 
-#define SPEAR6XX_ML_SDRAM_BASE		UL(0x00000000)
 /* ICM1 - Low speed connection */
 #define SPEAR6XX_ICM1_BASE		UL(0xD0000000)
-
+#define VA_SPEAR6XX_ICM1_BASE		UL(0xFD000000)
 #define SPEAR6XX_ICM1_UART0_BASE	UL(0xD0000000)
-#define VA_SPEAR6XX_ICM1_UART0_BASE	IO_ADDRESS(SPEAR6XX_ICM1_UART0_BASE)
-
-#define SPEAR6XX_ICM1_UART1_BASE	UL(0xD0080000)
-#define SPEAR6XX_ICM1_SSP0_BASE		UL(0xD0100000)
-#define SPEAR6XX_ICM1_SSP1_BASE		UL(0xD0180000)
-#define SPEAR6XX_ICM1_I2C_BASE		UL(0xD0200000)
-#define SPEAR6XX_ICM1_JPEG_BASE		UL(0xD0800000)
-#define SPEAR6XX_ICM1_IRDA_BASE		UL(0xD1000000)
-#define SPEAR6XX_ICM1_FSMC_BASE		UL(0xD1800000)
-#define SPEAR6XX_ICM1_NAND_BASE		UL(0xD2000000)
-#define SPEAR6XX_ICM1_SRAM_BASE		UL(0xD2800000)
-
-/* ICM2 - Application Subsystem */
-#define SPEAR6XX_ICM2_BASE		UL(0xD8000000)
-#define SPEAR6XX_ICM2_TMR0_BASE		UL(0xD8000000)
-#define SPEAR6XX_ICM2_TMR1_BASE		UL(0xD8080000)
-#define SPEAR6XX_ICM2_GPIO_BASE		UL(0xD8100000)
-#define SPEAR6XX_ICM2_SSP2_BASE		UL(0xD8180000)
-#define SPEAR6XX_ICM2_ADC_BASE		UL(0xD8200000)
+#define VA_SPEAR6XX_ICM1_UART0_BASE	(VA_SPEAR6XX_ICM1_2_BASE | SPEAR6XX_ICM1_UART0_BASE)
 
 /* ML-1, 2 - Multi Layer CPU Subsystem */
 #define SPEAR6XX_ML_CPU_BASE		UL(0xF0000000)
-#define SPEAR6XX_CPU_TMR_BASE		UL(0xF0000000)
-#define SPEAR6XX_CPU_GPIO_BASE		UL(0xF0100000)
-#define SPEAR6XX_CPU_VIC_SEC_BASE	UL(0xF1000000)
-#define VA_SPEAR6XX_CPU_VIC_SEC_BASE	IO_ADDRESS(SPEAR6XX_CPU_VIC_SEC_BASE)
-#define SPEAR6XX_CPU_VIC_PRI_BASE	UL(0xF1100000)
-#define VA_SPEAR6XX_CPU_VIC_PRI_BASE	IO_ADDRESS(SPEAR6XX_CPU_VIC_PRI_BASE)
+#define VA_SPEAR6XX_ML_CPU_BASE		UL(0xF0000000)
 
 /* ICM3 - Basic Subsystem */
-#define SPEAR6XX_ICM3_BASE		UL(0xF8000000)
-#define SPEAR6XX_ICM3_SMEM_BASE		UL(0xF8000000)
 #define SPEAR6XX_ICM3_SMI_CTRL_BASE	UL(0xFC000000)
-#define SPEAR6XX_ICM3_CLCD_BASE		UL(0xFC200000)
+#define VA_SPEAR6XX_ICM3_SMI_CTRL_BASE	UL(0xFC000000)
 #define SPEAR6XX_ICM3_DMA_BASE		UL(0xFC400000)
-#define SPEAR6XX_ICM3_SDRAM_CTRL_BASE	UL(0xFC600000)
-#define SPEAR6XX_ICM3_TMR_BASE		UL(0xFC800000)
-#define SPEAR6XX_ICM3_WDT_BASE		UL(0xFC880000)
-#define SPEAR6XX_ICM3_RTC_BASE		UL(0xFC900000)
-#define SPEAR6XX_ICM3_GPIO_BASE		UL(0xFC980000)
 #define SPEAR6XX_ICM3_SYS_CTRL_BASE	UL(0xFCA00000)
-#define VA_SPEAR6XX_ICM3_SYS_CTRL_BASE	IO_ADDRESS(SPEAR6XX_ICM3_SYS_CTRL_BASE)
+#define VA_SPEAR6XX_ICM3_SYS_CTRL_BASE	(VA_SPEAR6XX_ICM3_SMI_CTRL_BASE | SPEAR6XX_ICM3_SYS_CTRL_BASE)
 #define SPEAR6XX_ICM3_MISC_REG_BASE	UL(0xFCA80000)
-#define VA_SPEAR6XX_ICM3_MISC_REG_BASE	IO_ADDRESS(SPEAR6XX_ICM3_MISC_REG_BASE)
-
-/* ICM4 - High Speed Connection */
-#define SPEAR6XX_ICM4_BASE		UL(0xE0000000)
-#define SPEAR6XX_ICM4_GMAC_BASE		UL(0xE0800000)
-#define SPEAR6XX_ICM4_USBD_FIFO_BASE	UL(0xE1000000)
-#define SPEAR6XX_ICM4_USBD_CSR_BASE	UL(0xE1100000)
-#define SPEAR6XX_ICM4_USBD_PLDT_BASE	UL(0xE1200000)
-#define SPEAR6XX_ICM4_USB_EHCI0_BASE	UL(0xE1800000)
-#define SPEAR6XX_ICM4_USB_OHCI0_BASE	UL(0xE1900000)
-#define SPEAR6XX_ICM4_USB_EHCI1_BASE	UL(0xE2000000)
-#define SPEAR6XX_ICM4_USB_OHCI1_BASE	UL(0xE2100000)
-#define SPEAR6XX_ICM4_USB_ARB_BASE	UL(0xE2800000)
+#define VA_SPEAR6XX_ICM3_MISC_REG_BASE	(VA_SPEAR6XX_ICM3_SMI_CTRL_BASE | SPEAR6XX_ICM3_MISC_REG_BASE)
 
 /* Debug uart for linux, will be used for debug and uncompress messages */
 #define SPEAR_DBG_UART_BASE		SPEAR6XX_ICM1_UART0_BASE

arch/arm/mach-spear6xx/include/mach/spear600.h

-/*
- * arch/arm/mach-spear66xx/include/mach/spear600.h
- *
- * SPEAr600 Machine specific definition
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifdef	CONFIG_MACH_SPEAR600
-
-#ifndef __MACH_SPEAR600_H
-#define __MACH_SPEAR600_H
-
-#endif /* __MACH_SPEAR600_H */
-
-#endif /* CONFIG_MACH_SPEAR600 */

arch/arm/mach-spear6xx/spear6xx.c

@@ -14,6 +14,8 @@
  */
 
 #include <linux/amba/pl08x.h>
+#include <linux/clk.h>
+#include <linux/err.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/of_irq.h>
@@ -21,9 +23,11 @@
 #include <asm/hardware/pl080.h>
 #include <asm/hardware/vic.h>
 #include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+#include <asm/mach/map.h>
 #include <plat/pl080.h>
 #include <mach/generic.h>
-#include <mach/hardware.h>
+#include <mach/spear.h>
 
 /* dmac device registration */
 static struct pl08x_channel_data spear600_dma_info[] = {
@@ -384,32 +388,29 @@ struct pl08x_platform_data pl080_plat_data = {
 	.num_slave_channels = ARRAY_SIZE(spear600_dma_info),
 };
 
-/* Following will create static virtual/physical mappings */
-static struct map_desc spear6xx_io_desc[] __initdata = {
+/*
+ * Following will create 16MB static virtual/physical mappings
+ * PHYSICAL		VIRTUAL
+ * 0xF0000000		0xF0000000
+ * 0xF1000000		0xF1000000
+ * 0xD0000000		0xFD000000
+ * 0xFC000000		0xFC000000
+ */
+struct map_desc spear6xx_io_desc[] __initdata = {
 	{
-		.virtual	= VA_SPEAR6XX_ICM1_UART0_BASE,
-		.pfn		= __phys_to_pfn(SPEAR6XX_ICM1_UART0_BASE),
-		.length		= SZ_4K,
-		.type		= MT_DEVICE
-	}, {
-		.virtual	= VA_SPEAR6XX_CPU_VIC_PRI_BASE,
-		.pfn		= __phys_to_pfn(SPEAR6XX_CPU_VIC_PRI_BASE),
-		.length		= SZ_4K,
+		.virtual	= VA_SPEAR6XX_ML_CPU_BASE,
+		.pfn		= __phys_to_pfn(SPEAR6XX_ML_CPU_BASE),
+		.length		= 2 * SZ_16M,
 		.type		= MT_DEVICE
-	}, {
-		.virtual	= VA_SPEAR6XX_CPU_VIC_SEC_BASE,
-		.pfn		= __phys_to_pfn(SPEAR6XX_CPU_VIC_SEC_BASE),
-		.length		= SZ_4K,
-		.type		= MT_DEVICE
-	}, {
-		.virtual	= VA_SPEAR6XX_ICM3_SYS_CTRL_BASE,
-		.pfn		= __phys_to_pfn(SPEAR6XX_ICM3_SYS_CTRL_BASE),
-		.length		= SZ_4K,
+	},	{
+		.virtual	= VA_SPEAR6XX_ICM1_BASE,
+		.pfn		= __phys_to_pfn(SPEAR6XX_ICM1_BASE),
+		.length		= SZ_16M,
 		.type		= MT_DEVICE
 	}, {
-		.virtual	= VA_SPEAR6XX_ICM3_MISC_REG_BASE,
-		.pfn		= __phys_to_pfn(SPEAR6XX_ICM3_MISC_REG_BASE),
-		.length		= SZ_4K,
+		.virtual	= VA_SPEAR6XX_ICM3_SMI_CTRL_BASE,
+		.pfn		= __phys_to_pfn(SPEAR6XX_ICM3_SMI_CTRL_BASE),
+		.length		= SZ_16M,
 		.type		= MT_DEVICE
 	},
 };
@@ -446,7 +447,7 @@ static void __init spear6xx_timer_init(void)
 	clk_put(gpt_clk);
 	clk_put(pclk);
 
-	spear_setup_timer();
+	spear_setup_of_timer();
 }
 
 struct sys_timer spear6xx_timer = {

arch/arm/plat-spear/include/plat/debug-macro.S

@@ -12,7 +12,7 @@
  */
 
 #include <linux/amba/serial.h>
-#include <mach/hardware.h>
+#include <mach/spear.h>
 
 		.macro	addruart, rp, rv, tmp
 		mov	\rp, #SPEAR_DBG_UART_BASE		@ Physical base

arch/arm/plat-spear/include/plat/hardware.h

-/*
- * arch/arm/plat-spear/include/plat/hardware.h
- *
- * Hardware definitions for SPEAr
- *
- * Copyright (C) 2010 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __PLAT_HARDWARE_H
-#define __PLAT_HARDWARE_H
-
-#endif /* __PLAT_HARDWARE_H */

arch/arm/plat-spear/include/plat/uncompress.h

@@ -13,7 +13,7 @@
 
 #include <linux/io.h>
 #include <linux/amba/serial.h>
-#include <mach/hardware.h>
+#include <mach/spear.h>
 
 #ifndef __PLAT_UNCOMPRESS_H
 #define __PLAT_UNCOMPRESS_H

arch/arm/plat-spear/pl080.c

@@ -17,6 +17,7 @@
 #include <linux/err.h>
 #include <linux/io.h>
 #include <linux/spinlock_types.h>
+#include <mach/spear.h>
 #include <mach/misc_regs.h>
 
 static spinlock_t lock = __SPIN_LOCK_UNLOCKED(x);

arch/arm/plat-spear/restart.c

@@ -13,7 +13,7 @@
 #include <linux/io.h>
 #include <asm/system_misc.h>
 #include <asm/hardware/sp810.h>
-#include <mach/hardware.h>
+#include <mach/spear.h>
 #include <mach/generic.h>
 
 void spear_restart(char mode, const char *cmd)

arch/arm/plat-spear/time.c

@@ -15,14 +15,15 @@
 #include <linux/err.h>
 #include <linux/init.h>
 #include <linux/interrupt.h>
+#include <linux/ioport.h>
 #include <linux/io.h>
 #include <linux/kernel.h>
+#include <linux/of_irq.h>
+#include <linux/of_address.h>
 #include <linux/time.h>
 #include <linux/irq.h>
 #include <asm/mach/time.h>
 #include <mach/generic.h>
-#include <mach/hardware.h>
-#include <mach/irqs.h>
 
 /*
  * We would use TIMER0 and TIMER1 as clockevent and clocksource.
@@ -175,7 +176,7 @@ static struct irqaction spear_timer_irq = {
 	.handler = spear_timer_interrupt
 };
 
-static void __init spear_clockevent_init(void)
+static void __init spear_clockevent_init(int irq)
 {
 	u32 tick_rate;
 
@@ -195,22 +196,35 @@ static void __init spear_clockevent_init(void)
 
 	clockevents_register_device(&clkevt);
 
-	setup_irq(SPEAR_GPT0_CHAN0_IRQ, &spear_timer_irq);
+	setup_irq(irq, &spear_timer_irq);
 }
 
-void __init spear_setup_timer(void)
+const static struct of_device_id timer_of_match[] __initconst = {
+	{ .compatible = "st,spear-timer", },
+	{ },
+};
+
+void __init spear_setup_of_timer(void)
 {
-	int ret;
+	struct device_node *np;
+	int irq, ret;
+
+	np = of_find_matching_node(NULL, timer_of_match);
+	if (!np) {
+		pr_err("%s: No timer passed via DT\n", __func__);
+		return;
+	}
 
-	if (!request_mem_region(SPEAR_GPT0_BASE, SZ_1K, "gpt0")) {
-		pr_err("%s:cannot get IO addr\n", __func__);
+	irq = irq_of_parse_and_map(np, 0);
+	if (!irq) {
+		pr_err("%s: No irq passed for timer via DT\n", __func__);
 		return;
 	}
 
-	gpt_base = (void __iomem *)ioremap(SPEAR_GPT0_BASE, SZ_1K);
+	gpt_base = of_iomap(np, 0);
 	if (!gpt_base) {
-		pr_err("%s:ioremap failed for gpt\n", __func__);
-		goto err_mem;
+		pr_err("%s: of iomap failed\n", __func__);
+		return;
 	}
 
 	gpt_clk = clk_get_sys("gpt0", NULL);
@@ -225,7 +239,7 @@ void __init spear_setup_timer(void)
 		goto err_prepare_enable_clk;
 	}
 
-	spear_clockevent_init();
+	spear_clockevent_init(irq);
 	spear_clocksource_init();
 
 	return;
@@ -234,6 +248,4 @@ void __init spear_setup_timer(void)
 	clk_put(gpt_clk);
 err_iomap:
 	iounmap(gpt_base);
-err_mem:
-	release_mem_region(SPEAR_GPT0_BASE, SZ_1K);
 }

drivers/of/address.c

 
+#include <linux/device.h>
 #include <linux/io.h>
 #include <linux/ioport.h>
 #include <linux/module.h>