i40e: geneve tunnel offload support

This patch adds driver hooks to implement ndo_ops to add/del
udp port in the HW to identify GENEVE tunnels.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/intel/i40e/i40e.h

@@ -245,6 +245,11 @@ struct i40e_tc_configuration {
 	struct i40e_tc_info tc_info[I40E_MAX_TRAFFIC_CLASS];
 };
 
+struct i40e_udp_port_config {
+	__be16 index;
+	u8 type;
+};
+
 /* struct that defines the Ethernet device */
 struct i40e_pf {
 	struct pci_dev *pdev;
@@ -281,11 +286,9 @@ struct i40e_pf {
 	u32 fd_atr_cnt;
 	u32 fd_tcp_rule;
 
-#ifdef CONFIG_I40E_VXLAN
-	__be16  vxlan_ports[I40E_MAX_PF_UDP_OFFLOAD_PORTS];
-	u16 pending_vxlan_bitmap;
+	struct i40e_udp_port_config udp_ports[I40E_MAX_PF_UDP_OFFLOAD_PORTS];
+	u16 pending_udp_bitmap;
 
-#endif
 	enum i40e_interrupt_policy int_policy;
 	u16 rx_itr_default;
 	u16 tx_itr_default;
@@ -322,9 +325,7 @@ struct i40e_pf {
 #define I40E_FLAG_FD_ATR_ENABLED		BIT_ULL(22)
 #define I40E_FLAG_PTP				BIT_ULL(25)
 #define I40E_FLAG_MFP_ENABLED			BIT_ULL(26)
-#ifdef CONFIG_I40E_VXLAN
-#define I40E_FLAG_VXLAN_FILTER_SYNC		BIT_ULL(27)
-#endif
+#define I40E_FLAG_UDP_FILTER_SYNC		BIT_ULL(27)
 #define I40E_FLAG_PORT_ID_VALID			BIT_ULL(28)
 #define I40E_FLAG_DCB_CAPABLE			BIT_ULL(29)
 #define I40E_FLAG_RSS_AQ_CAPABLE		BIT_ULL(31)
@@ -336,6 +337,7 @@ struct i40e_pf {
 #define I40E_FLAG_MULTIPLE_TCP_UDP_RSS_PCTYPE	BIT_ULL(38)
 #define I40E_FLAG_LINK_POLLING_ENABLED		BIT_ULL(39)
 #define I40E_FLAG_VEB_MODE_ENABLED		BIT_ULL(40)
+#define I40E_FLAG_GENEVE_OFFLOAD_CAPABLE	BIT_ULL(41)
 #define I40E_FLAG_NO_PCI_LINK_CHECK		BIT_ULL(42)
 
 	/* tracks features that get auto disabled by errors */

drivers/net/ethernet/intel/i40e/i40e_txrx.c

@@ -1380,7 +1380,7 @@ static inline void i40e_rx_checksum(struct i40e_vsi *vsi,
 	if (rx_error & BIT(I40E_RX_DESC_ERROR_PPRS_SHIFT))
 		return;
 
-	/* If VXLAN traffic has an outer UDPv4 checksum we need to check
+	/* If VXLAN/GENEVE traffic has an outer UDPv4 checksum we need to check
 	 * it in the driver, hardware does not do it for us.
 	 * Since L3L4P bit was set we assume a valid IHL value (>=5)
 	 * so the total length of IPv4 header is IHL*4 bytes
@@ -2001,7 +2001,7 @@ static void i40e_atr(struct i40e_ring *tx_ring, struct sk_buff *skb,
 	if (!(tx_flags & (I40E_TX_FLAGS_IPV4 | I40E_TX_FLAGS_IPV6)))
 		return;
 
-	if (!(tx_flags & I40E_TX_FLAGS_VXLAN_TUNNEL)) {
+	if (!(tx_flags & I40E_TX_FLAGS_UDP_TUNNEL)) {
 		/* snag network header to get L4 type and address */
 		hdr.network = skb_network_header(skb);
 
@@ -2086,7 +2086,7 @@ static void i40e_atr(struct i40e_ring *tx_ring, struct sk_buff *skb,
 		     I40E_TXD_FLTR_QW1_FD_STATUS_SHIFT;
 
 	dtype_cmd |= I40E_TXD_FLTR_QW1_CNT_ENA_MASK;
-	if (!(tx_flags & I40E_TX_FLAGS_VXLAN_TUNNEL))
+	if (!(tx_flags & I40E_TX_FLAGS_UDP_TUNNEL))
 		dtype_cmd |=
 			((u32)I40E_FD_ATR_STAT_IDX(pf->hw.pf_id) <<
 			I40E_TXD_FLTR_QW1_CNTINDEX_SHIFT) &
@@ -2319,7 +2319,7 @@ static void i40e_tx_enable_csum(struct sk_buff *skb, u32 *tx_flags,
 			oudph = udp_hdr(skb);
 			oiph = ip_hdr(skb);
 			l4_tunnel = I40E_TXD_CTX_UDP_TUNNELING;
-			*tx_flags |= I40E_TX_FLAGS_VXLAN_TUNNEL;
+			*tx_flags |= I40E_TX_FLAGS_UDP_TUNNEL;
 			break;
 		case IPPROTO_GRE:
 			l4_tunnel = I40E_TXD_CTX_GRE_TUNNELING;

drivers/net/ethernet/intel/i40e/i40e_txrx.h

@@ -163,7 +163,7 @@ enum i40e_dyn_idx_t {
 #define I40E_TX_FLAGS_FSO		BIT(7)
 #define I40E_TX_FLAGS_TSYN		BIT(8)
 #define I40E_TX_FLAGS_FD_SB		BIT(9)
-#define I40E_TX_FLAGS_VXLAN_TUNNEL	BIT(10)
+#define I40E_TX_FLAGS_UDP_TUNNEL	BIT(10)
 #define I40E_TX_FLAGS_VLAN_MASK		0xffff0000
 #define I40E_TX_FLAGS_VLAN_PRIO_MASK	0xe0000000
 #define I40E_TX_FLAGS_VLAN_PRIO_SHIFT	29