scsi: isci: phy: Fix a few different kernel-doc related issues

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/isci/phy.c:354: warning: Function parameter or member 'iphy' not described in 'phy_get_non_dummy_port'
 drivers/scsi/isci/phy.c:354: warning: expecting prototype for If the phy is(). Prototype was for phy_get_non_dummy_port() instead
 drivers/scsi/isci/phy.c:364: warning: wrong kernel-doc identifier on line:
 drivers/scsi/isci/phy.c:401: warning: wrong kernel-doc identifier on line:
 drivers/scsi/isci/phy.c:611: warning: Function parameter or member 'iphy' not described in 'sci_phy_complete_link_training'
 drivers/scsi/isci/phy.c:611: warning: Excess function parameter 'sci_phy' description in 'sci_phy_complete_link_training'
 drivers/scsi/isci/phy.c:1170: warning: Cannot understand  *
 drivers/scsi/isci/phy.c:1222: warning: Cannot understand  *
 drivers/scsi/isci/phy.c:1432: warning: Function parameter or member 'sas_phy' not described in 'isci_phy_control'
 drivers/scsi/isci/phy.c:1432: warning: Excess function parameter 'phy' description in 'isci_phy_control'

Link: https://lore.kernel.org/r/20210317091230.2912389-17-lee.jones@linaro.org
Cc: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

drivers/scsi/isci/phy.c

@@ -361,11 +361,9 @@ struct isci_port *phy_get_non_dummy_port(struct isci_phy *iphy)
 }
 
 /**
- * This method will assign a port to the phy object.
+ * sci_phy_set_port() - This method will assign a port to the phy object.
  * @out]: iphy This parameter specifies the phy for which to assign a port
  *    object.
- *
- *
  */
 void sci_phy_set_port(
 	struct isci_phy *iphy,
@@ -398,11 +396,11 @@ enum sci_status sci_phy_initialize(struct isci_phy *iphy,
 }
 
 /**
- * This method assigns the direct attached device ID for this phy.
+ * sci_phy_setup_transport() - This method assigns the direct attached device ID for this phy.
  *
- * @iphy The phy for which the direct attached device id is to
+ * @iphy: The phy for which the direct attached device id is to
  *       be assigned.
- * @device_id The direct attached device ID to assign to the phy.
+ * @device_id: The direct attached device ID to assign to the phy.
  *       This will either be the RNi for the device or an invalid RNi if there
  *       is no current device assigned to the phy.
  */
@@ -597,7 +595,7 @@ static void sci_phy_start_sata_link_training(struct isci_phy *iphy)
 /**
  * sci_phy_complete_link_training - perform processing common to
  *    all protocols upon completion of link training.
- * @sci_phy: This parameter specifies the phy object for which link training
+ * @iphy: This parameter specifies the phy object for which link training
  *    has completed.
  * @max_link_rate: This parameter specifies the maximum link rate to be
  *    associated with this phy.
@@ -1167,8 +1165,8 @@ static void sci_phy_starting_final_substate_enter(struct sci_base_state_machine
 }
 
 /**
- *
- * @sci_phy: This is the struct isci_phy object to stop.
+ * scu_link_layer_stop_protocol_engine()
+ * @iphy: This is the struct isci_phy object to stop.
  *
  * This method will stop the struct isci_phy object. This does not reset the
  * protocol engine it just suspends it and places it in a state where it will
@@ -1219,7 +1217,8 @@ static void scu_link_layer_start_oob(struct isci_phy *iphy)
 }
 
 /**
- *
+ * scu_link_layer_tx_hard_reset()
+ * @iphy: This is the struct isci_phy object to stop.
  *
  * This method will transmit a hard reset request on the specified phy. The SCU
  * hardware requires that we reset the OOB state machine and set the hard reset
@@ -1420,7 +1419,7 @@ void isci_phy_init(struct isci_phy *iphy, struct isci_host *ihost, int index)
 /**
  * isci_phy_control() - This function is one of the SAS Domain Template
  *    functions. This is a phy management function.
- * @phy: This parameter specifies the sphy being controlled.
+ * @sas_phy: This parameter specifies the sphy being controlled.
  * @func: This parameter specifies the phy control function being invoked.
  * @buf: This parameter is specific to the phy function being invoked.
  *