Merge remote-tracking branches 'spi/topic/acpi', 'spi/topic/axi-engine',...

Merge remote-tracking branches 'spi/topic/acpi', 'spi/topic/axi-engine', 'spi/topic/bcm2835' and 'spi/topic/bcm2835aux' into spi-next

Documentation/devicetree/bindings/spi/adi,axi-spi-engine.txt

+Analog Devices AXI SPI Engine controller Device Tree Bindings
+
+Required properties:
+- compatible		: Must be "adi,axi-spi-engine-1.00.a""
+- reg			: Physical base address and size of the register map.
+- interrupts		: Property with a value describing the interrupt
+			  number.
+- clock-names		: List of input clock names - "s_axi_aclk", "spi_clk"
+- clocks		: Clock phandles and specifiers (See clock bindings for
+			  details on clock-names and clocks).
+- #address-cells	: Must be <1>
+- #size-cells		: Must be <0>
+
+Optional subnodes:
+	Subnodes are use to represent the SPI slave devices connected to the SPI
+	master. They follow the generic SPI bindings as outlined in spi-bus.txt.
+
+Example:
+
+    spi@@44a00000 {
+		compatible = "adi,axi-spi-engine-1.00.a";
+		reg = <0x44a00000 0x1000>;
+		interrupts = <0 56 4>;
+		clocks = <&clkc 15 &clkc 15>;
+		clock-names = "s_axi_aclk", "spi_clk";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* SPI devices */
+    };

drivers/spi/Kconfig

@@ -75,11 +75,26 @@ config SPI_ATMEL
 	  This selects a driver for the Atmel SPI Controller, present on
 	  many AT32 (AVR32) and AT91 (ARM) chips.
 
+config SPI_AU1550
+	tristate "Au1550/Au1200/Au1300 SPI Controller"
+	depends on MIPS_ALCHEMY
+	select SPI_BITBANG
+	help
+	  If you say yes to this option, support will be included for the
+	  PSC SPI controller found on Au1550, Au1200 and Au1300 series.
+
+config SPI_AXI_SPI_ENGINE
+	tristate "Analog Devices AXI SPI Engine controller"
+	depends on HAS_IOMEM
+	help
+	  This enables support for the Analog Devices AXI SPI Engine SPI controller.
+	  It is part of the SPI Engine framework that is used in some Analog Devices
+	  reference designs for FPGAs.
+
 config SPI_BCM2835
 	tristate "BCM2835 SPI controller"
 	depends on GPIOLIB
 	depends on ARCH_BCM2835 || COMPILE_TEST
-	depends on GPIOLIB
 	help
 	  This selects a driver for the Broadcom BCM2835 SPI master.
 
@@ -90,8 +105,7 @@ config SPI_BCM2835
 
 config SPI_BCM2835AUX
 	tristate "BCM2835 SPI auxiliary controller"
-	depends on ARCH_BCM2835 || COMPILE_TEST
-	depends on GPIOLIB
+	depends on (ARCH_BCM2835 && GPIOLIB) || COMPILE_TEST
 	help
 	  This selects a driver for the Broadcom BCM2835 SPI aux master.
 
@@ -118,14 +132,6 @@ config SPI_BFIN_SPORT
 	help
 	  Enable support for a SPI bus via the Blackfin SPORT peripheral.
 
-config SPI_AU1550
-	tristate "Au1550/Au1200/Au1300 SPI Controller"
-	depends on MIPS_ALCHEMY
-	select SPI_BITBANG
-	help
-	  If you say yes to this option, support will be included for the
-	  PSC SPI controller found on Au1550, Au1200 and Au1300 series.
-
 config SPI_BCM53XX
 	tristate "Broadcom BCM53xx SPI controller"
 	depends on ARCH_BCM_5301X
@@ -197,6 +203,23 @@ config SPI_DAVINCI
 	help
 	  SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.
 
+config SPI_DESIGNWARE
+	tristate "DesignWare SPI controller core support"
+	help
+	  general driver for SPI controller core from DesignWare
+
+config SPI_DW_PCI
+	tristate "PCI interface driver for DW SPI core"
+	depends on SPI_DESIGNWARE && PCI
+
+config SPI_DW_MID_DMA
+	bool "DMA support for DW SPI controller on Intel MID platform"
+	depends on SPI_DW_PCI && DW_DMAC_PCI
+
+config SPI_DW_MMIO
+	tristate "Memory-mapped io interface driver for DW SPI core"
+	depends on SPI_DESIGNWARE
+
 config SPI_DLN2
        tristate "Diolan DLN-2 USB SPI adapter"
        depends on MFD_DLN2
@@ -346,6 +369,13 @@ config SPI_MT65XX
 	  say Y or M here.If you are not sure, say N.
 	  SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs.
 
+config SPI_NUC900
+	tristate "Nuvoton NUC900 series SPI"
+	depends on ARCH_W90X900
+	select SPI_BITBANG
+	help
+	  SPI driver for Nuvoton NUC900 series ARM SoCs
+
 config SPI_OC_TINY
 	tristate "OpenCores tiny SPI"
 	depends on GPIOLIB || COMPILE_TEST
@@ -647,34 +677,10 @@ config SPI_ZYNQMP_GQSPI
 	help
 	  Enables Xilinx GQSPI controller driver for Zynq UltraScale+ MPSoC.
 
-config SPI_NUC900
-	tristate "Nuvoton NUC900 series SPI"
-	depends on ARCH_W90X900
-	select SPI_BITBANG
-	help
-	  SPI driver for Nuvoton NUC900 series ARM SoCs
-
 #
 # Add new SPI master controllers in alphabetical order above this line
 #
 
-config SPI_DESIGNWARE
-	tristate "DesignWare SPI controller core support"
-	help
-	  general driver for SPI controller core from DesignWare
-
-config SPI_DW_PCI
-	tristate "PCI interface driver for DW SPI core"
-	depends on SPI_DESIGNWARE && PCI
-
-config SPI_DW_MID_DMA
-	bool "DMA support for DW SPI controller on Intel MID platform"
-	depends on SPI_DW_PCI && DW_DMAC_PCI
-
-config SPI_DW_MMIO
-	tristate "Memory-mapped io interface driver for DW SPI core"
-	depends on SPI_DESIGNWARE
-
 #
 # There are lots of SPI device types, with sensors and memory
 # being probably the most widely used ones.

drivers/spi/Makefile

@@ -15,6 +15,7 @@ obj-$(CONFIG_SPI_ALTERA)		+= spi-altera.o
 obj-$(CONFIG_SPI_ATMEL)			+= spi-atmel.o
 obj-$(CONFIG_SPI_ATH79)			+= spi-ath79.o
 obj-$(CONFIG_SPI_AU1550)		+= spi-au1550.o
+obj-$(CONFIG_SPI_AXI_SPI_ENGINE)	+= spi-axi-spi-engine.o
 obj-$(CONFIG_SPI_BCM2835)		+= spi-bcm2835.o
 obj-$(CONFIG_SPI_BCM2835AUX)		+= spi-bcm2835aux.o
 obj-$(CONFIG_SPI_BCM53XX)		+= spi-bcm53xx.o

drivers/spi/spi-bcm2835.c

@@ -727,11 +727,6 @@ static int bcm2835_spi_setup(struct spi_device *spi)
 			spi->chip_select, spi->cs_gpio, err);
 		return err;
 	}
-	/* the implementation of pinctrl-bcm2835 currently does not
-	 * set the GPIO value when using gpio_direction_output
-	 * so we are setting it here explicitly
-	 */
-	gpio_set_value(spi->cs_gpio, (spi->mode & SPI_CS_HIGH) ? 0 : 1);
 
 	return 0;
 }

drivers/spi/spi-bcm2835aux.c

@@ -64,9 +64,9 @@
 #define BCM2835_AUX_SPI_CNTL0_VAR_WIDTH	0x00004000
 #define BCM2835_AUX_SPI_CNTL0_DOUTHOLD	0x00003000
 #define BCM2835_AUX_SPI_CNTL0_ENABLE	0x00000800
-#define BCM2835_AUX_SPI_CNTL0_CPHA_IN	0x00000400
+#define BCM2835_AUX_SPI_CNTL0_IN_RISING	0x00000400
 #define BCM2835_AUX_SPI_CNTL0_CLEARFIFO	0x00000200
-#define BCM2835_AUX_SPI_CNTL0_CPHA_OUT	0x00000100
+#define BCM2835_AUX_SPI_CNTL0_OUT_RISING	0x00000100
 #define BCM2835_AUX_SPI_CNTL0_CPOL	0x00000080
 #define BCM2835_AUX_SPI_CNTL0_MSBF_OUT	0x00000040
 #define BCM2835_AUX_SPI_CNTL0_SHIFTLEN	0x0000003F
@@ -92,9 +92,6 @@
 #define BCM2835_AUX_SPI_POLLING_LIMIT_US	30
 #define BCM2835_AUX_SPI_POLLING_JIFFIES		2
 
-#define BCM2835_AUX_SPI_MODE_BITS (SPI_CPOL | SPI_CPHA | SPI_CS_HIGH \
-				  | SPI_NO_CS)
-
 struct bcm2835aux_spi {
 	void __iomem *regs;
 	struct clk *clk;
@@ -212,9 +209,15 @@ static irqreturn_t bcm2835aux_spi_interrupt(int irq, void *dev_id)
 		ret = IRQ_HANDLED;
 	}
 
-	/* and if rx_len is 0 then wake up completion and disable spi */
+	if (!bs->tx_len) {
+		/* disable tx fifo empty interrupt */
+		bcm2835aux_wr(bs, BCM2835_AUX_SPI_CNTL1, bs->cntl[1] |
+			BCM2835_AUX_SPI_CNTL1_IDLE);
+	}
+
+	/* and if rx_len is 0 then disable interrupts and wake up completion */
 	if (!bs->rx_len) {
-		bcm2835aux_spi_reset_hw(bs);
+		bcm2835aux_wr(bs, BCM2835_AUX_SPI_CNTL1, bs->cntl[1]);
 		complete(&master->xfer_completion);
 	}
 
@@ -307,9 +310,6 @@ static int bcm2835aux_spi_transfer_one_poll(struct spi_master *master,
 		}
 	}
 
-	/* Transfer complete - reset SPI HW */
-	bcm2835aux_spi_reset_hw(bs);
-
 	/* and return without waiting for completion */
 	return 0;
 }
@@ -330,10 +330,6 @@ static int bcm2835aux_spi_transfer_one(struct spi_master *master,
 	 * resulting (potentially) in more interrupts when transferring
 	 * more than 12 bytes
 	 */
-	bs->cntl[0] = BCM2835_AUX_SPI_CNTL0_ENABLE |
-		      BCM2835_AUX_SPI_CNTL0_VAR_WIDTH |
-		      BCM2835_AUX_SPI_CNTL0_MSBF_OUT;
-	bs->cntl[1] = BCM2835_AUX_SPI_CNTL1_MSBF_IN;
 
 	/* set clock */
 	spi_hz = tfr->speed_hz;
@@ -348,17 +344,13 @@ static int bcm2835aux_spi_transfer_one(struct spi_master *master,
 	} else { /* the slowest we can go */
 		speed = BCM2835_AUX_SPI_CNTL0_SPEED_MAX;
 	}
+	/* mask out old speed from previous spi_transfer */
+	bs->cntl[0] &= ~(BCM2835_AUX_SPI_CNTL0_SPEED);
+	/* set the new speed */
 	bs->cntl[0] |= speed << BCM2835_AUX_SPI_CNTL0_SPEED_SHIFT;
 
 	spi_used_hz = clk_hz / (2 * (speed + 1));
 
-	/* handle all the modes */
-	if (spi->mode & SPI_CPOL)
-		bs->cntl[0] |= BCM2835_AUX_SPI_CNTL0_CPOL;
-	if (spi->mode & SPI_CPHA)
-		bs->cntl[0] |= BCM2835_AUX_SPI_CNTL0_CPHA_OUT |
-			       BCM2835_AUX_SPI_CNTL0_CPHA_IN;
-
 	/* set transmit buffers and length */
 	bs->tx_buf = tfr->tx_buf;
 	bs->rx_buf = tfr->rx_buf;
@@ -382,6 +374,40 @@ static int bcm2835aux_spi_transfer_one(struct spi_master *master,
 	return bcm2835aux_spi_transfer_one_irq(master, spi, tfr);
 }
 
+static int bcm2835aux_spi_prepare_message(struct spi_master *master,
+					  struct spi_message *msg)
+{
+	struct spi_device *spi = msg->spi;
+	struct bcm2835aux_spi *bs = spi_master_get_devdata(master);
+
+	bs->cntl[0] = BCM2835_AUX_SPI_CNTL0_ENABLE |
+		      BCM2835_AUX_SPI_CNTL0_VAR_WIDTH |
+		      BCM2835_AUX_SPI_CNTL0_MSBF_OUT;
+	bs->cntl[1] = BCM2835_AUX_SPI_CNTL1_MSBF_IN;
+
+	/* handle all the modes */
+	if (spi->mode & SPI_CPOL) {
+		bs->cntl[0] |= BCM2835_AUX_SPI_CNTL0_CPOL;
+		bs->cntl[0] |= BCM2835_AUX_SPI_CNTL0_OUT_RISING;
+	} else {
+		bs->cntl[0] |= BCM2835_AUX_SPI_CNTL0_IN_RISING;
+	}
+	bcm2835aux_wr(bs, BCM2835_AUX_SPI_CNTL1, bs->cntl[1]);
+	bcm2835aux_wr(bs, BCM2835_AUX_SPI_CNTL0, bs->cntl[0]);
+
+	return 0;
+}
+
+static int bcm2835aux_spi_unprepare_message(struct spi_master *master,
+					    struct spi_message *msg)
+{
+	struct bcm2835aux_spi *bs = spi_master_get_devdata(master);
+
+	bcm2835aux_spi_reset_hw(bs);
+
+	return 0;
+}
+
 static void bcm2835aux_spi_handle_err(struct spi_master *master,
 				      struct spi_message *msg)
 {
@@ -405,11 +431,13 @@ static int bcm2835aux_spi_probe(struct platform_device *pdev)
 	}
 
 	platform_set_drvdata(pdev, master);
-	master->mode_bits = BCM2835_AUX_SPI_MODE_BITS;
+	master->mode_bits = (SPI_CPOL | SPI_CS_HIGH | SPI_NO_CS);
 	master->bits_per_word_mask = SPI_BPW_MASK(8);
 	master->num_chipselect = -1;
 	master->transfer_one = bcm2835aux_spi_transfer_one;
 	master->handle_err = bcm2835aux_spi_handle_err;
+	master->prepare_message = bcm2835aux_spi_prepare_message;
+	master->unprepare_message = bcm2835aux_spi_unprepare_message;
 	master->dev.of_node = pdev->dev.of_node;
 
 	bs = spi_master_get_devdata(master);

drivers/spi/spi.c

@@ -1589,13 +1589,30 @@ static void of_register_spi_devices(struct spi_master *master) { }
 static int acpi_spi_add_resource(struct acpi_resource *ares, void *data)
 {
 	struct spi_device *spi = data;
+	struct spi_master *master = spi->master;
 
 	if (ares->type == ACPI_RESOURCE_TYPE_SERIAL_BUS) {
 		struct acpi_resource_spi_serialbus *sb;
 
 		sb = &ares->data.spi_serial_bus;
 		if (sb->type == ACPI_RESOURCE_SERIAL_TYPE_SPI) {
-			spi->chip_select = sb->device_selection;
+			/*
+			 * ACPI DeviceSelection numbering is handled by the
+			 * host controller driver in Windows and can vary
+			 * from driver to driver. In Linux we always expect
+			 * 0 .. max - 1 so we need to ask the driver to
+			 * translate between the two schemes.
+			 */
+			if (master->fw_translate_cs) {
+				int cs = master->fw_translate_cs(master,
+						sb->device_selection);
+				if (cs < 0)
+					return cs;
+				spi->chip_select = cs;
+			} else {
+				spi->chip_select = sb->device_selection;
+			}
+
 			spi->max_speed_hz = sb->connection_speed;
 
 			if (sb->clock_phase == ACPI_SPI_SECOND_PHASE)

include/linux/spi/spi.h

@@ -372,6 +372,9 @@ static inline void spi_unregister_driver(struct spi_driver *sdrv)
  * @dma_rx: DMA receive channel
  * @dummy_rx: dummy receive buffer for full-duplex devices
  * @dummy_tx: dummy transmit buffer for full-duplex devices
+ * @fw_translate_cs: If the boot firmware uses different numbering scheme
+ *	what Linux expects, this optional hook can be used to translate
+ *	between the two.
  *
  * Each SPI master controller can communicate with one or more @spi_device
  * children.  These make a small bus, sharing MOSI, MISO and SCK signals
@@ -542,6 +545,8 @@ struct spi_master {
 	/* dummy data for full duplex devices */
 	void			*dummy_rx;
 	void			*dummy_tx;
+
+	int (*fw_translate_cs)(struct spi_master *master, unsigned cs);
 };
 
 static inline void *spi_master_get_devdata(struct spi_master *master)