Commit 6d3dd362 authored by Dan Murphy's avatar Dan Murphy Committed by Sebastian Reichel

dt-binding: bq25980: Add the bq25980 flash charger

Add yaml for the bq25980 flash charger.
Signed-off-by: default avatarDan Murphy <dmurphy@ti.com>
Reviewed-by: default avatarRob Herring <robh@kernel.org>
Signed-off-by: default avatarSebastian Reichel <sebastian.reichel@collabora.com>
parent 304bff2f
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
# Copyright (C) 2020 Texas Instruments Incorporated
%YAML 1.2
---
$id: "http://devicetree.org/schemas/power/supply/bq25980.yaml#"
$schema: "http://devicetree.org/meta-schemas/core.yaml#"
title: TI BQ25980 Flash Charger
maintainers:
- Dan Murphy <dmurphy@ti.com>
- Ricardo Rivera-Matos <r-rivera-matos@ti.com>
description: |
The BQ25980, BQ25975, and BQ25960 are a series of flash chargers intended
for use in high-power density portable electronics. These inductorless
switching chargers can provide over 97% efficiency by making use of the
switched capacitor architecture.
allOf:
- $ref: power-supply.yaml#
properties:
compatible:
enum:
- ti,bq25980
- ti,bq25975
- ti,bq25960
reg:
maxItems: 1
ti,watchdog-timeout-ms:
description: |
Watchdog timer in milli seconds. 0 disables the watchdog.
default: 0
minimum: 0
maximum: 300000
enum: [ 0, 5000, 10000, 50000, 300000]
ti,sc-ovp-limit-microvolt:
description: |
Minimum input voltage limit in micro volts with a when the charger is in
switch cap mode. 100000 micro volt step.
default: 17800000
minimum: 14000000
maximum: 22000000
ti,sc-ocp-limit-microamp:
description: |
Maximum input current limit in micro amps with a 100000 micro amp step.
minimum: 100000
maximum: 3300000
ti,bypass-ovp-limit-microvolt:
description: |
Minimum input voltage limit in micro volts with a when the charger is in
switch cap mode. 50000 micro volt step.
minimum: 7000000
maximum: 12750000
ti,bypass-ocp-limit-microamp:
description: |
Maximum input current limit in micro amps with a 100000 micro amp step.
minimum: 100000
maximum: 3300000
ti,bypass-enable:
type: boolean
description: Enables bypass mode at boot time
interrupts:
description: |
Indicates that the device state has changed.
monitored-battery:
$ref: /schemas/types.yaml#/definitions/phandle
description: phandle to the battery node being monitored
required:
- compatible
- reg
- monitored-battery
unevaluatedProperties: false
examples:
- |
bat: battery {
compatible = "simple-battery";
constant-charge-current-max-microamp = <4000000>;
constant-charge-voltage-max-microvolt = <8400000>;
precharge-current-microamp = <160000>;
charge-term-current-microamp = <160000>;
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
i2c0 {
#address-cells = <1>;
#size-cells = <0>;
bq25980: charger@65 {
compatible = "ti,bq25980";
reg = <0x65>;
interrupt-parent = <&gpio1>;
interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
ti,watchdog-timer = <0>;
ti,sc-ocp-limit-microamp = <2000000>;
ti,sc-ovp-limit-microvolt = <17800000>;
monitored-battery = <&bat>;
};
};
...
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment