dt-bindings: pinctrl: qcom,msm8974: convert to dtschema

Convert Qualcomm MSM8974 pin controller bindings to DT schema.  Keep the
parsing of pin configuration subnodes consistent with other Qualcomm
schemas (children named with '-state' suffix, their children with
'-pins').
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20221017012225.8579-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt

-Qualcomm MSM8974 TLMM block
-
-Required properties:
-- compatible: "qcom,msm8974-pinctrl"
-- reg: Should be the base address and length of the TLMM block.
-- interrupts: Should be the parent IRQ of the TLMM block.
-- interrupt-controller: Marks the device node as an interrupt controller.
-- #interrupt-cells: Should be two.
-- gpio-controller: Marks the device node as a GPIO controller.
-- #gpio-cells : Should be two.
-                The first cell is the gpio pin number and the
-                second cell is used for optional parameters.
-- gpio-ranges: see ../gpio/gpio.txt
-
-Optional properties:
-
-- gpio-reserved-ranges: see ../gpio/gpio.txt
-
-Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
-a general description of GPIO and interrupt bindings.
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices, including the meaning of the
-phrase "pin configuration node".
-
-Qualcomm's pin configuration nodes act as a container for an arbitrary number of
-subnodes. Each of these subnodes represents some desired configuration for a
-pin, a group, or a list of pins or groups. This configuration can include the
-mux function to select on those pin(s)/group(s), and various pin configuration
-parameters, such as pull-up, drive strength, etc.
-
-The name of each subnode is not important; all subnodes should be enumerated
-and processed purely based on their content.
-
-Each subnode only affects those parameters that are explicitly listed. In
-other words, a subnode that lists a mux function but no pin configuration
-parameters implies no information about any pin configuration parameters.
-Similarly, a pin subnode that describes a pullup parameter implies no
-information about e.g. the mux function.
-
-
-The following generic properties as defined in pinctrl-bindings.txt are valid
-to specify in a pin configuration subnode:
- pins, function, bias-disable, bias-pull-down, bias-pull-up, drive-strength.
-
-Non-empty subnodes must specify the 'pins' property.
-Note that not all properties are valid for all pins.
-
-
-Valid values for pins are:
-  gpio0-gpio145
-    Supports mux, bias and drive-strength
-
-  sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data
-    Supports bias and drive-strength
-
-  hsic_data, hsic_strobe
-    Supports only mux
-
-Valid values for function are:
-  cci_i2c0, cci_i2c1, uim1, uim2, uim_batt_alarm,
-  blsp_uim1, blsp_uart1, blsp_i2c1, blsp_spi1,
-  blsp_uim2, blsp_uart2, blsp_i2c2, blsp_spi2,
-  blsp_uim3, blsp_uart3, blsp_i2c3, blsp_spi3,
-  blsp_uim4, blsp_uart4, blsp_i2c4, blsp_spi4,
-  blsp_uim5, blsp_uart5, blsp_i2c5, blsp_spi5,
-  blsp_uim6, blsp_uart6, blsp_i2c6, blsp_spi6,
-  blsp_uim7, blsp_uart7, blsp_i2c7, blsp_spi7,
-  blsp_uim8, blsp_uart8, blsp_i2c8, blsp_spi8,
-  blsp_uim9, blsp_uart9, blsp_i2c9, blsp_spi9,
-  blsp_uim10, blsp_uart10, blsp_i2c10, blsp_spi10,
-  blsp_uim11, blsp_uart11, blsp_i2c11, blsp_spi11,
-  blsp_uim12, blsp_uart12, blsp_i2c12, blsp_spi12,
-  blsp_spi1_cs1, blsp_spi2_cs2, blsp_spi_cs3, blsp_spi2_cs1, blsp_spi2_cs2
-  blsp_spi2_cs3, blsp_spi10_cs1, blsp_spi10_cs2, blsp_spi10_cs3,
-  sdc3, sdc4, gcc_gp_clk1, gcc_gp_clk2, gcc_gp_clk3, cci_timer0, cci_timer1,
-  cci_timer2, cci_timer3, cci_async_in0, cci_async_in1, cci_async_in2,
-  cam_mckl0, cam_mclk1, cam_mclk2, cam_mclk3, mdp_vsync, hdmi_cec, hdmi_ddc,
-  hdmi_hpd, edp_hpd, gp_pdm0, gp_pdm1, gp_pdm2, gp_pdm3, gp0_clk, gp1_clk,
-  gp_mn, tsif1, tsif2, hsic, grfc, audio_ref_clk, qua_mi2s, pri_mi2s, spkr_mi2s,
-  ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus, hsic_ctl, gpio
-
-  (Note that this is not yet the complete list of functions)
-
-
-
-Example:
-
-	msmgpio: pinctrl@fd510000 {
-		compatible = "qcom,msm8974-pinctrl";
-		reg = <0xfd510000 0x4000>;
-
-		gpio-controller;
-		#gpio-cells = <2>;
-		gpio-ranges = <&msmgpio 0 0 146>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		interrupts = <0 208 0>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&uart2_default>;
-
-		uart2_default: uart2_default {
-			mux {
-				pins = "gpio4", "gpio5";
-				function = "blsp_uart2";
-			};
-
-			tx {
-				pins = "gpio4";
-				drive-strength = <4>;
-				bias-disable;
-			};
-
-			rx {
-				pins = "gpio5";
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-		};
-	};

Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,msm8974-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm MSM8974 TLMM pin controller
+
+maintainers:
+  - Bjorn Andersson <andersson@kernel.org>
+  - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+
+description:
+  Top Level Mode Multiplexer pin controller in Qualcomm MSM8974 SoC.
+
+properties:
+  compatible:
+    const: qcom,msm8974-pinctrl
+
+  reg:
+    maxItems: 1
+
+  interrupts: true
+  interrupt-controller: true
+  "#interrupt-cells": true
+  gpio-controller: true
+  "#gpio-cells": true
+  gpio-ranges: true
+  wakeup-parent: true
+
+  gpio-reserved-ranges:
+    minItems: 1
+    maxItems: 73
+
+  gpio-line-names:
+    maxItems: 146
+
+patternProperties:
+  "-state$":
+    oneOf:
+      - $ref: "#/$defs/qcom-msm8974-tlmm-state"
+      - patternProperties:
+          "-pins$":
+            $ref: "#/$defs/qcom-msm8974-tlmm-state"
+        additionalProperties: false
+
+$defs:
+  qcom-msm8974-tlmm-state:
+    type: object
+    description:
+      Pinctrl node's client devices use subnodes for desired pin configuration.
+      Client device subnodes use below standard properties.
+    $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
+
+    properties:
+      pins:
+        description:
+          List of gpio pins affected by the properties specified in this
+          subnode.
+        items:
+          oneOf:
+            - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-3][0-9]|14[0-5])$"
+            - enum: [ hsic_data, hsic_strobe, sdc1_clk, sdc1_cmd, sdc1_data,
+                      sdc2_clk, sdc2_cmd, sdc2_data ]
+        minItems: 1
+        maxItems: 36
+
+      function:
+        description:
+          Specify the alternative function to be configured for the specified
+          pins.
+
+        enum: [ gpio, cci_i2c0, cci_i2c1, uim1, uim2, uim_batt_alarm,
+                blsp_uim1, blsp_uart1, blsp_i2c1, blsp_spi1, blsp_uim2,
+                blsp_uart2, blsp_i2c2, blsp_spi2, blsp_uim3, blsp_uart3,
+                blsp_i2c3, blsp_spi3, blsp_uim4, blsp_uart4, blsp_i2c4,
+                blsp_spi4, blsp_uim5, blsp_uart5, blsp_i2c5, blsp_spi5,
+                blsp_uim6, blsp_uart6, blsp_i2c6, blsp_spi6, blsp_uim7,
+                blsp_uart7, blsp_i2c7, blsp_spi7, blsp_uim8, blsp_uart8,
+                blsp_i2c8, blsp_spi8, blsp_uim9, blsp_uart9, blsp_i2c9,
+                blsp_spi9, blsp_uim10, blsp_uart10, blsp_i2c10, blsp_spi10,
+                blsp_uim11, blsp_uart11, blsp_i2c11, blsp_spi11, blsp_uim12,
+                blsp_uart12, blsp_i2c12, blsp_spi12, blsp_spi1_cs1,
+                blsp_spi2_cs2, blsp_spi_cs3, blsp_spi2_cs1, blsp_spi2_cs2
+                blsp_spi2_cs3, blsp_spi10_cs1, blsp_spi10_cs2, blsp_spi10_cs3,
+                sdc3, sdc4, gcc_gp_clk1, gcc_gp_clk2, gcc_gp_clk3, cci_timer0,
+                cci_timer1, cci_timer2, cci_timer3, cci_async_in0,
+                cci_async_in1, cci_async_in2, cam_mckl0, cam_mclk1, cam_mclk2,
+                cam_mclk3, mdp_vsync, hdmi_cec, hdmi_ddc, hdmi_hpd, edp_hpd,
+                gp_pdm0, gp_pdm1, gp_pdm2, gp_pdm3, gp0_clk, gp1_clk, gp_mn,
+                tsif1, tsif2, hsic, grfc, audio_ref_clk, qua_mi2s, pri_mi2s,
+                spkr_mi2s, ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus, hsic_ctl ]
+
+      bias-pull-down: true
+      bias-pull-up: true
+      bias-disable: true
+      drive-strength: true
+      input-enable: true
+      output-high: true
+      output-low: true
+
+    required:
+      - pins
+
+    allOf:
+      - if:
+          properties:
+            pins:
+              contains:
+                enum:
+                  - hsic_data
+                  - hsic_strobe
+          required:
+            - pins
+        then:
+          properties:
+            bias-pull-down: false
+            bias-pull-up: false
+            bias-disable: false
+            drive-strength: false
+            input-enable: false
+            output-high: false
+            output-low: false
+
+    additionalProperties: false
+
+allOf:
+  - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    tlmm: pinctrl@fd510000 {
+        compatible = "qcom,msm8974-pinctrl";
+        reg = <0xfd510000 0x4000>;
+        gpio-controller;
+        gpio-ranges = <&tlmm 0 0 146>;
+        #gpio-cells = <2>;
+        interrupt-controller;
+        #interrupt-cells = <2>;
+        interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+
+        sdc1-off-state {
+            clk-pins {
+                pins = "sdc1_clk";
+                bias-disable;
+                drive-strength = <2>;
+            };
+
+            cmd-pins {
+                pins = "sdc1_cmd";
+                bias-pull-up;
+                drive-strength = <2>;
+            };
+
+            data-pins {
+                pins = "sdc1_data";
+                bias-pull-up;
+                drive-strength = <2>;
+            };
+        };
+
+        blsp2-uart1-sleep-state {
+            pins = "gpio41", "gpio42", "gpio43", "gpio44";
+            function = "gpio";
+            drive-strength = <2>;
+            bias-pull-down;
+        };
+
+        hsic-state {
+            pins = "hsic_data", "hsic_strobe";
+        };
+    };