Commit 6fefe19f authored by Zhang Rui's avatar Zhang Rui

Merge branches 'thermal-core', 'thermal-soc', 'thermal-intel' and 'ida-conversion' into next

......@@ -17,6 +17,12 @@ Required properties:
calibration data, as specified by the SoC reference manual.
The first cell of each pair is the value to be written to TTCFGR,
and the second is the value to be written to TSCFGR.
- #thermal-sensor-cells : Must be 1. The sensor specifier is the monitoring
site ID, and represents the "n" in TRITSRn and TRATSRn.
Optional property:
- little-endian : If present, the TMU registers are little endian. If absent,
the default is big endian.
Example:
......@@ -60,4 +66,5 @@ tmu@f0000 {
0x00030000 0x00000012
0x00030001 0x0000001d>;
#thermal-sensor-cells = <1>;
};
* DT bindings for Renesas R-Car Gen3 Thermal Sensor driver
On R-Car Gen3 SoCs, the thermal sensor controllers (TSC) control the thermal
sensors (THS) which are the analog circuits for measuring temperature (Tj)
inside the LSI.
Required properties:
- compatible : "renesas,<soctype>-thermal",
Examples with soctypes are:
- "renesas,r8a7795-thermal" (R-Car H3)
- "renesas,r8a7796-thermal" (R-Car M3-W)
- reg : Address ranges of the thermal registers. Each sensor
needs one address range. Sorting must be done in
increasing order according to datasheet, i.e.
TSC1, TSC2, ...
- clocks : Must contain a reference to the functional clock.
- #thermal-sensor-cells : must be <1>.
Optional properties:
- interrupts : interrupts routed to the TSC (3 for H3 and M3-W)
- power-domain : Must contain a reference to the power domain. This
property is mandatory if the thermal sensor instance
is part of a controllable power domain.
Example:
tsc: thermal@e6198000 {
compatible = "renesas,r8a7795-thermal";
reg = <0 0xe6198000 0 0x68>,
<0 0xe61a0000 0 0x5c>,
<0 0xe61a8000 0 0x5c>;
interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 522>;
power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
#thermal-sensor-cells = <1>;
status = "okay";
};
thermal-zones {
sensor_thermal1: sensor-thermal1 {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsc 0>;
trips {
sensor1_crit: sensor1-crit {
temperature = <90000>;
hysteresis = <2000>;
type = "critical";
};
};
};
};
* ZTE zx2967 family Thermal
Required Properties:
- compatible: should be one of the following.
* zte,zx296718-thermal
- reg: physical base address of the controller and length of memory mapped
region.
- clocks : Pairs of phandle and specifier referencing the controller's clocks.
- clock-names: "topcrm" for the topcrm clock.
"apb" for the apb clock.
- #thermal-sensor-cells: must be 0.
Please note: slope coefficient defined in thermal-zones section need to be
multiplied by 1000.
Example for tempsensor:
tempsensor: tempsensor@148a000 {
compatible = "zte,zx296718-thermal";
reg = <0x0148a000 0x20>;
clocks = <&topcrm TEMPSENSOR_GATE>, <&audiocrm AUDIO_TS_PCLK>;
clock-names = "topcrm", "apb";
#thermal-sensor-cells = <0>;
};
Example for cooling device:
cooling_dev: cooling_dev {
cluster0_cooling_dev: cluster0-cooling-dev {
#cooling-cells = <2>;
cpumask = <0xf>;
capacitance = <1500>;
};
cluster1_cooling_dev: cluster1-cooling-dev {
#cooling-cells = <2>;
cpumask = <0x30>;
capacitance = <2000>;
};
};
Example for thermal zones:
thermal-zones {
zx296718_thermal: zx296718_thermal {
polling-delay-passive = <500>;
polling-delay = <1000>;
sustainable-power = <6500>;
thermal-sensors = <&tempsensor 0>;
/*
* slope need to be multiplied by 1000.
*/
coefficients = <1951 (-922)>;
trips {
trip0: switch_on_temperature {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
trip1: desired_temperature {
temperature = <100000>;
hysteresis = <2000>;
type = "passive";
};
crit: critical_temperature {
temperature = <110000>;
hysteresis = <2000>;
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&trip0>;
cooling-device = <&gpu 2 5>;
};
map1 {
trip = <&trip0>;
cooling-device = <&cluster0_cooling_dev 1 2>;
};
map2 {
trip = <&trip1>;
cooling-device = <&cluster0_cooling_dev 1 2>;
};
map3 {
trip = <&crit>;
cooling-device = <&cluster0_cooling_dev 1 2>;
};
map4 {
trip = <&trip0>;
cooling-device = <&cluster1_cooling_dev 1 2>;
contribution = <9000>;
};
map5 {
trip = <&trip1>;
cooling-device = <&cluster1_cooling_dev 1 2>;
contribution = <4096>;
};
map6 {
trip = <&crit>;
cooling-device = <&cluster1_cooling_dev 1 2>;
contribution = <4096>;
};
};
};
};
......@@ -422,7 +422,7 @@ tmu: tmu@f0000 {
0x00030001 0x0000000d
0x00030002 0x00000019
0x00030003 0x00000024>;
#thermal-sensor-cells = <0>;
#thermal-sensor-cells = <1>;
};
thermal-zones {
......@@ -430,7 +430,7 @@ cpu_thermal: cpu-thermal {
polling-delay-passive = <1000>;
polling-delay = <5000>;
thermal-sensors = <&tmu>;
thermal-sensors = <&tmu 0>;
trips {
cpu_alert: cpu-alert {
......
......@@ -526,7 +526,7 @@ tmu: tmu@f0000 {
0x00030000 0x00000012
0x00030001 0x0000001d>;
#thermal-sensor-cells = <0>;
#thermal-sensor-cells = <1>;
};
thermal-zones {
......@@ -534,7 +534,7 @@ cpu_thermal: cpu-thermal {
polling-delay-passive = <1000>;
polling-delay = <5000>;
thermal-sensors = <&tmu>;
thermal-sensors = <&tmu 2>;
trips {
cpu_alert: cpu-alert {
......
......@@ -245,6 +245,15 @@ config RCAR_THERMAL
Enable this to plug the R-Car thermal sensor driver into the Linux
thermal framework.
config RCAR_GEN3_THERMAL
tristate "Renesas R-Car Gen3 thermal driver"
depends on ARCH_RENESAS || COMPILE_TEST
depends on HAS_IOMEM
depends on OF
help
Enable this to plug the R-Car Gen3 thermal sensor driver into the Linux
thermal framework.
config KIRKWOOD_THERMAL
tristate "Temperature sensor on Marvell Kirkwood SoCs"
depends on MACH_KIRKWOOD || COMPILE_TEST
......@@ -436,4 +445,12 @@ depends on (ARCH_QCOM && OF) || COMPILE_TEST
source "drivers/thermal/qcom/Kconfig"
endmenu
config ZX2967_THERMAL
tristate "Thermal sensors on zx2967 SoC"
depends on ARCH_ZX || COMPILE_TEST
help
Enable the zx2967 thermal sensors driver, which supports
the primitive temperature sensor embedded in zx2967 SoCs.
This sensor generates the real time die temperature.
endif
......@@ -31,6 +31,7 @@ obj-$(CONFIG_QCOM_SPMI_TEMP_ALARM) += qcom-spmi-temp-alarm.o
obj-$(CONFIG_SPEAR_THERMAL) += spear_thermal.o
obj-$(CONFIG_ROCKCHIP_THERMAL) += rockchip_thermal.o
obj-$(CONFIG_RCAR_THERMAL) += rcar_thermal.o
obj-$(CONFIG_RCAR_GEN3_THERMAL) += rcar_gen3_thermal.o
obj-$(CONFIG_KIRKWOOD_THERMAL) += kirkwood_thermal.o
obj-y += samsung/
obj-$(CONFIG_DOVE_THERMAL) += dove_thermal.o
......@@ -56,3 +57,4 @@ obj-$(CONFIG_TEGRA_SOCTHERM) += tegra/
obj-$(CONFIG_HISI_THERMAL) += hisi_thermal.o
obj-$(CONFIG_MTK_THERMAL) += mtk_thermal.o
obj-$(CONFIG_GENERIC_ADC_THERMAL) += thermal-generic-adc.o
obj-$(CONFIG_ZX2967_THERMAL) += zx2967_thermal.o
......@@ -65,42 +65,7 @@ struct clock_cooling_device {
};
#define to_clock_cooling_device(x) \
container_of(x, struct clock_cooling_device, clk_rate_change_nb)
static DEFINE_IDR(clock_idr);
static DEFINE_MUTEX(cooling_clock_lock);
/**
* clock_cooling_get_idr - function to get an unique id.
* @id: int * value generated by this function.
*
* This function will populate @id with an unique
* id, using the idr API.
*
* Return: 0 on success, an error code on failure.
*/
static int clock_cooling_get_idr(int *id)
{
int ret;
mutex_lock(&cooling_clock_lock);
ret = idr_alloc(&clock_idr, NULL, 0, 0, GFP_KERNEL);
mutex_unlock(&cooling_clock_lock);
if (unlikely(ret < 0))
return ret;
*id = ret;
return 0;
}
/**
* release_idr - function to free the unique id.
* @id: int value representing the unique id.
*/
static void release_idr(int id)
{
mutex_lock(&cooling_clock_lock);
idr_remove(&clock_idr, id);
mutex_unlock(&cooling_clock_lock);
}
static DEFINE_IDA(clock_ida);
/* Below code defines functions to be used for clock as cooling device */
......@@ -432,16 +397,17 @@ clock_cooling_register(struct device *dev, const char *clock_name)
if (IS_ERR(ccdev->clk))
return ERR_CAST(ccdev->clk);
ret = clock_cooling_get_idr(&ccdev->id);
if (ret)
return ERR_PTR(-EINVAL);
ret = ida_simple_get(&clock_ida, 0, 0, GFP_KERNEL);
if (ret < 0)
return ERR_PTR(ret);
ccdev->id = ret;
snprintf(dev_name, sizeof(dev_name), "thermal-clock-%d", ccdev->id);
cdev = thermal_cooling_device_register(dev_name, ccdev,
&clock_cooling_ops);
if (IS_ERR(cdev)) {
release_idr(ccdev->id);
ida_simple_remove(&clock_ida, ccdev->id);
return ERR_PTR(-EINVAL);
}
ccdev->cdev = cdev;
......@@ -450,7 +416,7 @@ clock_cooling_register(struct device *dev, const char *clock_name)
/* Assuming someone has already filled the opp table for this device */
ret = dev_pm_opp_init_cpufreq_table(dev, &ccdev->freq_table);
if (ret) {
release_idr(ccdev->id);
ida_simple_remove(&clock_ida, ccdev->id);
return ERR_PTR(ret);
}
ccdev->clock_state = 0;
......@@ -481,6 +447,6 @@ void clock_cooling_unregister(struct thermal_cooling_device *cdev)
dev_pm_opp_free_cpufreq_table(ccdev->dev, &ccdev->freq_table);
thermal_cooling_device_unregister(ccdev->cdev);
release_idr(ccdev->id);
ida_simple_remove(&clock_ida, ccdev->id);
}
EXPORT_SYMBOL_GPL(clock_cooling_unregister);
......@@ -26,6 +26,7 @@
#include <linux/thermal.h>
#include <linux/cpufreq.h>
#include <linux/err.h>
#include <linux/idr.h>
#include <linux/pm_opp.h>
#include <linux/slab.h>
#include <linux/cpu.h>
......@@ -104,50 +105,13 @@ struct cpufreq_cooling_device {
struct device *cpu_dev;
get_static_t plat_get_static_power;
};
static DEFINE_IDR(cpufreq_idr);
static DEFINE_MUTEX(cooling_cpufreq_lock);
static DEFINE_IDA(cpufreq_ida);
static unsigned int cpufreq_dev_count;
static DEFINE_MUTEX(cooling_list_lock);
static LIST_HEAD(cpufreq_dev_list);
/**
* get_idr - function to get a unique id.
* @idr: struct idr * handle used to create a id.
* @id: int * value generated by this function.
*
* This function will populate @id with an unique
* id, using the idr API.
*
* Return: 0 on success, an error code on failure.
*/
static int get_idr(struct idr *idr, int *id)
{
int ret;
mutex_lock(&cooling_cpufreq_lock);
ret = idr_alloc(idr, NULL, 0, 0, GFP_KERNEL);
mutex_unlock(&cooling_cpufreq_lock);
if (unlikely(ret < 0))
return ret;
*id = ret;
return 0;
}
/**
* release_idr - function to free the unique id.
* @idr: struct idr * handle used for creating the id.
* @id: int value representing the unique id.
*/
static void release_idr(struct idr *idr, int id)
{
mutex_lock(&cooling_cpufreq_lock);
idr_remove(idr, id);
mutex_unlock(&cooling_cpufreq_lock);
}
/* Below code defines functions to be used for cpufreq as cooling device */
/**
......@@ -886,11 +850,12 @@ __cpufreq_cooling_register(struct device_node *np,
cooling_ops = &cpufreq_cooling_ops;
}
ret = get_idr(&cpufreq_idr, &cpufreq_dev->id);
if (ret) {
ret = ida_simple_get(&cpufreq_ida, 0, 0, GFP_KERNEL);
if (ret < 0) {
cool_dev = ERR_PTR(ret);
goto free_power_table;
}
cpufreq_dev->id = ret;
/* Fill freq-table in descending order of frequencies */
for (i = 0, freq = -1; i <= cpufreq_dev->max_level; i++) {
......@@ -910,27 +875,24 @@ __cpufreq_cooling_register(struct device_node *np,
cool_dev = thermal_of_cooling_device_register(np, dev_name, cpufreq_dev,
cooling_ops);
if (IS_ERR(cool_dev))
goto remove_idr;
goto remove_ida;
cpufreq_dev->clipped_freq = cpufreq_dev->freq_table[0];
cpufreq_dev->cool_dev = cool_dev;
mutex_lock(&cooling_cpufreq_lock);
mutex_lock(&cooling_list_lock);
list_add(&cpufreq_dev->node, &cpufreq_dev_list);
mutex_unlock(&cooling_list_lock);
/* Register the notifier for first cpufreq cooling device */
if (!cpufreq_dev_count++)
cpufreq_register_notifier(&thermal_cpufreq_notifier_block,
CPUFREQ_POLICY_NOTIFIER);
mutex_unlock(&cooling_cpufreq_lock);
mutex_unlock(&cooling_list_lock);
goto put_policy;
remove_idr:
release_idr(&cpufreq_idr, cpufreq_dev->id);
remove_ida:
ida_simple_remove(&cpufreq_ida, cpufreq_dev->id);
free_power_table:
kfree(cpufreq_dev->dyn_power_table);
free_table:
......@@ -1072,20 +1034,17 @@ void cpufreq_cooling_unregister(struct thermal_cooling_device *cdev)
cpufreq_dev = cdev->devdata;
mutex_lock(&cooling_list_lock);
/* Unregister the notifier for the last cpufreq cooling device */
mutex_lock(&cooling_cpufreq_lock);
if (!--cpufreq_dev_count)
cpufreq_unregister_notifier(&thermal_cpufreq_notifier_block,
CPUFREQ_POLICY_NOTIFIER);
mutex_lock(&cooling_list_lock);
list_del(&cpufreq_dev->node);
mutex_unlock(&cooling_list_lock);
mutex_unlock(&cooling_cpufreq_lock);
thermal_cooling_device_unregister(cpufreq_dev->cool_dev);
release_idr(&cpufreq_idr, cpufreq_dev->id);
ida_simple_remove(&cpufreq_ida, cpufreq_dev->id);
kfree(cpufreq_dev->dyn_power_table);
kfree(cpufreq_dev->time_in_idle_timestamp);
kfree(cpufreq_dev->time_in_idle);
......
......@@ -21,14 +21,14 @@
#include <linux/devfreq.h>
#include <linux/devfreq_cooling.h>
#include <linux/export.h>
#include <linux/idr.h>
#include <linux/slab.h>
#include <linux/pm_opp.h>
#include <linux/thermal.h>
#include <trace/events/thermal.h>
static DEFINE_MUTEX(devfreq_lock);
static DEFINE_IDR(devfreq_idr);
static DEFINE_IDA(devfreq_ida);
/**
* struct devfreq_cooling_device - Devfreq cooling device
......@@ -57,42 +57,6 @@ struct devfreq_cooling_device {
struct devfreq_cooling_power *power_ops;
};
/**
* get_idr - function to get a unique id.
* @idr: struct idr * handle used to create a id.
* @id: int * value generated by this function.
*
* This function will populate @id with an unique
* id, using the idr API.
*
* Return: 0 on success, an error code on failure.
*/
static int get_idr(struct idr *idr, int *id)
{
int ret;
mutex_lock(&devfreq_lock);
ret = idr_alloc(idr, NULL, 0, 0, GFP_KERNEL);
mutex_unlock(&devfreq_lock);
if (unlikely(ret < 0))
return ret;
*id = ret;
return 0;
}
/**
* release_idr - function to free the unique id.
* @idr: struct idr * handle used for creating the id.
* @id: int value representing the unique id.
*/
static void release_idr(struct idr *idr, int id)
{
mutex_lock(&devfreq_lock);
idr_remove(idr, id);
mutex_unlock(&devfreq_lock);
}
/**
* partition_enable_opps() - disable all opps above a given state
* @dfc: Pointer to devfreq we are operating on
......@@ -496,9 +460,10 @@ of_devfreq_cooling_register_power(struct device_node *np, struct devfreq *df,
if (err)
goto free_dfc;
err = get_idr(&devfreq_idr, &dfc->id);
if (err)
err = ida_simple_get(&devfreq_ida, 0, 0, GFP_KERNEL);
if (err < 0)
goto free_tables;
dfc->id = err;
snprintf(dev_name, sizeof(dev_name), "thermal-devfreq-%d", dfc->id);
......@@ -509,15 +474,15 @@ of_devfreq_cooling_register_power(struct device_node *np, struct devfreq *df,
dev_err(df->dev.parent,
"Failed to register devfreq cooling device (%d)\n",
err);
goto release_idr;
goto release_ida;
}
dfc->cdev = cdev;
return cdev;
release_idr:
release_idr(&devfreq_idr, dfc->id);
release_ida:
ida_simple_remove(&devfreq_ida, dfc->id);
free_tables:
kfree(dfc->power_table);
kfree(dfc->freq_table);
......@@ -565,7 +530,7 @@ void devfreq_cooling_unregister(struct thermal_cooling_device *cdev)
dfc = cdev->devdata;
thermal_cooling_device_unregister(dfc->cdev);
release_idr(&devfreq_idr, dfc->id);
ida_simple_remove(&devfreq_ida, dfc->id);
kfree(dfc->power_table);
kfree(dfc->freq_table);
......
......@@ -489,6 +489,10 @@ static int imx_thermal_probe(struct platform_device *pdev)
data->tempmon = map;
data->socdata = of_device_get_match_data(&pdev->dev);
if (!data->socdata) {
dev_err(&pdev->dev, "no device match found\n");
return -ENODEV;
}
/* make sure the IRQ flag is clear before enabling irq on i.MX6SX */
if (data->socdata->version == TEMPMON_IMX6SX) {
......
......@@ -461,16 +461,13 @@ static void poll_pkg_cstate(struct work_struct *dummy)
{
static u64 msr_last;
static u64 tsc_last;
static unsigned long jiffies_last;
u64 msr_now;
unsigned long jiffies_now;
u64 tsc_now;
u64 val64;
msr_now = pkg_state_counter();
tsc_now = rdtsc();
jiffies_now = jiffies;
/* calculate pkg cstate vs tsc ratio */
if (!msr_last || !tsc_last)
......@@ -485,7 +482,6 @@ static void poll_pkg_cstate(struct work_struct *dummy)
/* update record */
msr_last = msr_now;
jiffies_last = jiffies_now;
tsc_last = tsc_now;
if (true == clamping)
......
......@@ -183,37 +183,37 @@ struct mtk_thermal {
};
/* MT8173 thermal sensor data */
const int mt8173_bank_data[MT8173_NUM_ZONES][3] = {
static const int mt8173_bank_data[MT8173_NUM_ZONES][3] = {
{ MT8173_TS2, MT8173_TS3 },
{ MT8173_TS2, MT8173_TS4 },
{ MT8173_TS1, MT8173_TS2, MT8173_TSABB },
{ MT8173_TS2 },
};
const int mt8173_msr[MT8173_NUM_SENSORS_PER_ZONE] = {
static const int mt8173_msr[MT8173_NUM_SENSORS_PER_ZONE] = {
TEMP_MSR0, TEMP_MSR1, TEMP_MSR2, TEMP_MSR2
};
const int mt8173_adcpnp[MT8173_NUM_SENSORS_PER_ZONE] = {
static const int mt8173_adcpnp[MT8173_NUM_SENSORS_PER_ZONE] = {
TEMP_ADCPNP0, TEMP_ADCPNP1, TEMP_ADCPNP2, TEMP_ADCPNP3
};
const int mt8173_mux_values[MT8173_NUM_SENSORS] = { 0, 1, 2, 3, 16 };
static const int mt8173_mux_values[MT8173_NUM_SENSORS] = { 0, 1, 2, 3, 16 };
/* MT2701 thermal sensor data */
const int mt2701_bank_data[MT2701_NUM_SENSORS] = {
static const int mt2701_bank_data[MT2701_NUM_SENSORS] = {
MT2701_TS1, MT2701_TS2, MT2701_TSABB
};
const int mt2701_msr[MT2701_NUM_SENSORS_PER_ZONE] = {
static const int mt2701_msr[MT2701_NUM_SENSORS_PER_ZONE] = {
TEMP_MSR0, TEMP_MSR1, TEMP_MSR2
};
const int mt2701_adcpnp[MT2701_NUM_SENSORS_PER_ZONE] = {
static const int mt2701_adcpnp[MT2701_NUM_SENSORS_PER_ZONE] = {
TEMP_ADCPNP0, TEMP_ADCPNP1, TEMP_ADCPNP2
};
const int mt2701_mux_values[MT2701_NUM_SENSORS] = { 0, 1, 16 };
static const int mt2701_mux_values[MT2701_NUM_SENSORS] = { 0, 1, 16 };
/**
* The MT8173 thermal controller has four banks. Each bank can read up to
......
/*
* R-Car Gen3 THS thermal sensor driver
* Based on rcar_thermal.c and work from Hien Dang and Khiem Nguyen.
*
* Copyright (C) 2016 Renesas Electronics Corporation.
* Copyright (C) 2016 Sang Engineering
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; version 2 of the License.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
*/
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/module.h>
#include <linux/mutex.h>
#include <linux/of_device.h>
#include <linux/platform_device.h>
#include <linux/pm_runtime.h>
#include <linux/thermal.h>
/* Register offsets */
#define REG_GEN3_IRQSTR 0x04
#define REG_GEN3_IRQMSK 0x08
#define REG_GEN3_IRQCTL 0x0C
#define REG_GEN3_IRQEN 0x10
#define REG_GEN3_IRQTEMP1 0x14
#define REG_GEN3_IRQTEMP2 0x18
#define REG_GEN3_IRQTEMP3 0x1C
#define REG_GEN3_CTSR 0x20
#define REG_GEN3_THCTR 0x20
#define REG_GEN3_TEMP 0x28
#define REG_GEN3_THCODE1 0x50
#define REG_GEN3_THCODE2 0x54
#define REG_GEN3_THCODE3 0x58
/* CTSR bits */
#define CTSR_PONM BIT(8)
#define CTSR_AOUT BIT(7)
#define CTSR_THBGR BIT(5)
#define CTSR_VMEN BIT(4)
#define CTSR_VMST BIT(1)
#define CTSR_THSST BIT(0)
/* THCTR bits */
#define THCTR_PONM BIT(6)
#define THCTR_THSST BIT(0)
#define CTEMP_MASK 0xFFF
#define MCELSIUS(temp) ((temp) * 1000)
#define GEN3_FUSE_MASK 0xFFF
#define TSC_MAX_NUM 3
/* Structure for thermal temperature calculation */
struct equation_coefs {
int a1;
int b1;
int a2;
int b2;
};
struct rcar_gen3_thermal_tsc {
void __iomem *base;
struct thermal_zone_device *zone;
struct equation_coefs coef;
struct mutex lock;
};
struct rcar_gen3_thermal_priv {
struct rcar_gen3_thermal_tsc *tscs[TSC_MAX_NUM];
};
struct rcar_gen3_thermal_data {
void (*thermal_init)(struct rcar_gen3_thermal_tsc *tsc);
};
static inline u32 rcar_gen3_thermal_read(struct rcar_gen3_thermal_tsc *tsc,
u32 reg)
{
return ioread32(tsc->base + reg);
}
static inline void rcar_gen3_thermal_write(struct rcar_gen3_thermal_tsc *tsc,
u32 reg, u32 data)
{
iowrite32(data, tsc->base + reg);
}
/*
* Linear approximation for temperature
*
* [reg] = [temp] * a + b => [temp] = ([reg] - b) / a
*
* The constants a and b are calculated using two triplets of int values PTAT
* and THCODE. PTAT and THCODE can either be read from hardware or use hard
* coded values from driver. The formula to calculate a and b are taken from
* BSP and sparsely documented and understood.
*
* Examining the linear formula and the formula used to calculate constants a
* and b while knowing that the span for PTAT and THCODE values are between
* 0x000 and 0xfff the largest integer possible is 0xfff * 0xfff == 0xffe001.
* Integer also needs to be signed so that leaves 7 bits for binary
* fixed point scaling.
*/
#define FIXPT_SHIFT 7
#define FIXPT_INT(_x) ((_x) << FIXPT_SHIFT)
#define FIXPT_DIV(_a, _b) DIV_ROUND_CLOSEST(((_a) << FIXPT_SHIFT), (_b))
#define FIXPT_TO_MCELSIUS(_x) ((_x) * 1000 >> FIXPT_SHIFT)
#define RCAR3_THERMAL_GRAN 500 /* mili Celsius */
/* no idea where these constants come from */
#define TJ_1 96
#define TJ_3 -41
static void rcar_gen3_thermal_calc_coefs(struct equation_coefs *coef,
int *ptat, int *thcode)
{
int tj_2;
/* TODO: Find documentation and document constant calculation formula */
/*
* Division is not scaled in BSP and if scaled it might overflow
* the dividend (4095 * 4095 << 14 > INT_MAX) so keep it unscaled
*/
tj_2 = (FIXPT_INT((ptat[1] - ptat[2]) * 137)
/ (ptat[0] - ptat[2])) - FIXPT_INT(41);
coef->a1 = FIXPT_DIV(FIXPT_INT(thcode[1] - thcode[2]),
tj_2 - FIXPT_INT(TJ_3));
coef->b1 = FIXPT_INT(thcode[2]) - coef->a1 * TJ_3;
coef->a2 = FIXPT_DIV(FIXPT_INT(thcode[1] - thcode[0]),
tj_2 - FIXPT_INT(TJ_1));
coef->b2 = FIXPT_INT(thcode[0]) - coef->a2 * TJ_1;
}
static int rcar_gen3_thermal_round(int temp)
{
int result, round_offs;
round_offs = temp >= 0 ? RCAR3_THERMAL_GRAN / 2 :
-RCAR3_THERMAL_GRAN / 2;
result = (temp + round_offs) / RCAR3_THERMAL_GRAN;
return result * RCAR3_THERMAL_GRAN;
}
static int rcar_gen3_thermal_get_temp(void *devdata, int *temp)
{
struct rcar_gen3_thermal_tsc *tsc = devdata;
int mcelsius, val1, val2;
u32 reg;
/* Read register and convert to mili Celsius */
mutex_lock(&tsc->lock);
reg = rcar_gen3_thermal_read(tsc, REG_GEN3_TEMP) & CTEMP_MASK;
val1 = FIXPT_DIV(FIXPT_INT(reg) - tsc->coef.b1, tsc->coef.a1);
val2 = FIXPT_DIV(FIXPT_INT(reg) - tsc->coef.b2, tsc->coef.a2);
mcelsius = FIXPT_TO_MCELSIUS((val1 + val2) / 2);
mutex_unlock(&tsc->lock);
/* Make sure we are inside specifications */
if ((mcelsius < MCELSIUS(-40)) || (mcelsius > MCELSIUS(125)))
return -EIO;
/* Round value to device granularity setting */
*temp = rcar_gen3_thermal_round(mcelsius);
return 0;
}
static struct thermal_zone_of_device_ops rcar_gen3_tz_of_ops = {
.get_temp = rcar_gen3_thermal_get_temp,
};
static void r8a7795_thermal_init(struct rcar_gen3_thermal_tsc *tsc)
{
rcar_gen3_thermal_write(tsc, REG_GEN3_CTSR, CTSR_THBGR);
rcar_gen3_thermal_write(tsc, REG_GEN3_CTSR, 0x0);
usleep_range(1000, 2000);
rcar_gen3_thermal_write(tsc, REG_GEN3_CTSR, CTSR_PONM);
rcar_gen3_thermal_write(tsc, REG_GEN3_IRQCTL, 0x3F);
rcar_gen3_thermal_write(tsc, REG_GEN3_CTSR,
CTSR_PONM | CTSR_AOUT | CTSR_THBGR | CTSR_VMEN);
usleep_range(100, 200);
rcar_gen3_thermal_write(tsc, REG_GEN3_CTSR,
CTSR_PONM | CTSR_AOUT | CTSR_THBGR | CTSR_VMEN |
CTSR_VMST | CTSR_THSST);
usleep_range(1000, 2000);
}
static void r8a7796_thermal_init(struct rcar_gen3_thermal_tsc *tsc)
{
u32 reg_val;
reg_val = rcar_gen3_thermal_read(tsc, REG_GEN3_THCTR);
reg_val &= ~THCTR_PONM;
rcar_gen3_thermal_write(tsc, REG_GEN3_THCTR, reg_val);
usleep_range(1000, 2000);
rcar_gen3_thermal_write(tsc, REG_GEN3_IRQCTL, 0x3F);
reg_val = rcar_gen3_thermal_read(tsc, REG_GEN3_THCTR);
reg_val |= THCTR_THSST;
rcar_gen3_thermal_write(tsc, REG_GEN3_THCTR, reg_val);
}
static const struct rcar_gen3_thermal_data r8a7795_data = {
.thermal_init = r8a7795_thermal_init,
};
static const struct rcar_gen3_thermal_data r8a7796_data = {
.thermal_init = r8a7796_thermal_init,
};
static const struct of_device_id rcar_gen3_thermal_dt_ids[] = {
{ .compatible = "renesas,r8a7795-thermal", .data = &r8a7795_data},
{ .compatible = "renesas,r8a7796-thermal", .data = &r8a7796_data},
{},
};
MODULE_DEVICE_TABLE(of, rcar_gen3_thermal_dt_ids);
static int rcar_gen3_thermal_remove(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
pm_runtime_put(dev);
pm_runtime_disable(dev);
return 0;
}
static int rcar_gen3_thermal_probe(struct platform_device *pdev)
{
struct rcar_gen3_thermal_priv *priv;
struct device *dev = &pdev->dev;
struct resource *res;
struct thermal_zone_device *zone;
int ret, i;
const struct rcar_gen3_thermal_data *match_data =
of_device_get_match_data(dev);
/* default values if FUSEs are missing */
/* TODO: Read values from hardware on supported platforms */
int ptat[3] = { 2351, 1509, 435 };
int thcode[TSC_MAX_NUM][3] = {
{ 3248, 2800, 2221 },
{ 3245, 2795, 2216 },
{ 3250, 2805, 2237 },
};
priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
if (!priv)
return -ENOMEM;
platform_set_drvdata(pdev, priv);
pm_runtime_enable(dev);
pm_runtime_get_sync(dev);
for (i = 0; i < TSC_MAX_NUM; i++) {
struct rcar_gen3_thermal_tsc *tsc;
tsc = devm_kzalloc(dev, sizeof(*tsc), GFP_KERNEL);
if (!tsc) {
ret = -ENOMEM;
goto error_unregister;
}
res = platform_get_resource(pdev, IORESOURCE_MEM, i);
if (!res)
break;
tsc->base = devm_ioremap_resource(dev, res);
if (IS_ERR(tsc->base)) {
ret = PTR_ERR(tsc->base);
goto error_unregister;
}
priv->tscs[i] = tsc;
mutex_init(&tsc->lock);
match_data->thermal_init(tsc);
rcar_gen3_thermal_calc_coefs(&tsc->coef, ptat, thcode[i]);
zone = devm_thermal_zone_of_sensor_register(dev, i, tsc,
&rcar_gen3_tz_of_ops);
if (IS_ERR(zone)) {
dev_err(dev, "Can't register thermal zone\n");
ret = PTR_ERR(zone);
goto error_unregister;
}
tsc->zone = zone;
}
return 0;
error_unregister:
rcar_gen3_thermal_remove(pdev);
return ret;
}
static struct platform_driver rcar_gen3_thermal_driver = {
.driver = {
.name = "rcar_gen3_thermal",
.of_match_table = rcar_gen3_thermal_dt_ids,
},
.probe = rcar_gen3_thermal_probe,
.remove = rcar_gen3_thermal_remove,
};
module_platform_driver(rcar_gen3_thermal_driver);
MODULE_LICENSE("GPL v2");
MODULE_DESCRIPTION("R-Car Gen3 THS thermal sensor driver");
MODULE_AUTHOR("Wolfram Sang <wsa+renesas@sang-engineering.com>");
......@@ -1168,7 +1168,6 @@ static int exynos_of_sensor_conf(struct device_node *np,
pdata->default_temp_offset = (u8)value;
of_property_read_u32(np, "samsung,tmu_cal_type", &pdata->cal_type);
of_property_read_u32(np, "samsung,tmu_cal_mode", &pdata->cal_mode);
of_node_put(np);
return 0;
......
......@@ -70,7 +70,6 @@ struct exynos_tmu_platform_data {
enum soc_type type;
u32 cal_type;
u32 cal_mode;
};
#endif /* _EXYNOS_TMU_H */
......@@ -36,9 +36,8 @@ MODULE_AUTHOR("Zhang Rui");
MODULE_DESCRIPTION("Generic thermal management sysfs support");
MODULE_LICENSE("GPL v2");
static DEFINE_IDR(thermal_tz_idr);
static DEFINE_IDR(thermal_cdev_idr);
static DEFINE_MUTEX(thermal_idr_lock);
static DEFINE_IDA(thermal_tz_ida);
static DEFINE_IDA(thermal_cdev_ida);
static LIST_HEAD(thermal_tz_list);
static LIST_HEAD(thermal_cdev_list);
......@@ -589,29 +588,6 @@ void thermal_zone_device_unbind_exception(struct thermal_zone_device *tz,
* - thermal zone devices lifecycle: registration, unregistration,
* binding, and unbinding.
*/
static int get_idr(struct idr *idr, struct mutex *lock, int *id)
{
int ret;
if (lock)
mutex_lock(lock);
ret = idr_alloc(idr, NULL, 0, 0, GFP_KERNEL);
if (lock)
mutex_unlock(lock);
if (unlikely(ret < 0))
return ret;
*id = ret;
return 0;
}
static void release_idr(struct idr *idr, struct mutex *lock, int id)
{
if (lock)
mutex_lock(lock);
idr_remove(idr, id);
if (lock)
mutex_unlock(lock);
}
/**
* thermal_zone_bind_cooling_device() - bind a cooling device to a thermal zone
......@@ -685,15 +661,16 @@ int thermal_zone_bind_cooling_device(struct thermal_zone_device *tz,
dev->target = THERMAL_NO_TARGET;
dev->weight = weight;
result = get_idr(&tz->idr, &tz->lock, &dev->id);
if (result)
result = ida_simple_get(&tz->ida, 0, 0, GFP_KERNEL);
if (result < 0)
goto free_mem;
dev->id = result;
sprintf(dev->name, "cdev%d", dev->id);
result =
sysfs_create_link(&tz->device.kobj, &cdev->device.kobj, dev->name);
if (result)
goto release_idr;
goto release_ida;
sprintf(dev->attr_name, "cdev%d_trip_point", dev->id);
sysfs_attr_init(&dev->attr.attr);
......@@ -737,8 +714,8 @@ int thermal_zone_bind_cooling_device(struct thermal_zone_device *tz,
device_remove_file(&tz->device, &dev->attr);
remove_symbol_link:
sysfs_remove_link(&tz->device.kobj, dev->name);
release_idr:
release_idr(&tz->idr, &tz->lock, dev->id);
release_ida:
ida_simple_remove(&tz->ida, dev->id);
free_mem:
kfree(dev);
return result;
......@@ -785,7 +762,7 @@ int thermal_zone_unbind_cooling_device(struct thermal_zone_device *tz,
device_remove_file(&tz->device, &pos->weight_attr);
device_remove_file(&tz->device, &pos->attr);
sysfs_remove_link(&tz->device.kobj, pos->name);
release_idr(&tz->idr, &tz->lock, pos->id);
ida_simple_remove(&tz->ida, pos->id);
kfree(pos);
return 0;
}
......@@ -925,12 +902,13 @@ __thermal_cooling_device_register(struct device_node *np,
if (!cdev)
return ERR_PTR(-ENOMEM);
result = get_idr(&thermal_cdev_idr, &thermal_idr_lock, &cdev->id);
if (result) {
result = ida_simple_get(&thermal_cdev_ida, 0, 0, GFP_KERNEL);
if (result < 0) {
kfree(cdev);
return ERR_PTR(result);
}
cdev->id = result;
strlcpy(cdev->type, type ? : "", sizeof(cdev->type));
mutex_init(&cdev->lock);
INIT_LIST_HEAD(&cdev->thermal_instances);
......@@ -943,7 +921,7 @@ __thermal_cooling_device_register(struct device_node *np,
dev_set_name(&cdev->device, "cooling_device%d", cdev->id);
result = device_register(&cdev->device);
if (result) {
release_idr(&thermal_cdev_idr, &thermal_idr_lock, cdev->id);
ida_simple_remove(&thermal_cdev_ida, cdev->id);
kfree(cdev);
return ERR_PTR(result);
}
......@@ -1070,7 +1048,7 @@ void thermal_cooling_device_unregister(struct thermal_cooling_device *cdev)
mutex_unlock(&thermal_list_lock);
release_idr(&thermal_cdev_idr, &thermal_idr_lock, cdev->id);
ida_simple_remove(&thermal_cdev_ida, cdev->id);
device_unregister(&cdev->device);
}
EXPORT_SYMBOL_GPL(thermal_cooling_device_unregister);
......@@ -1172,14 +1150,15 @@ thermal_zone_device_register(const char *type, int trips, int mask,
return ERR_PTR(-ENOMEM);
INIT_LIST_HEAD(&tz->thermal_instances);
idr_init(&tz->idr);
ida_init(&tz->ida);
mutex_init(&tz->lock);
result = get_idr(&thermal_tz_idr, &thermal_idr_lock, &tz->id);
if (result) {
result = ida_simple_get(&thermal_tz_ida, 0, 0, GFP_KERNEL);
if (result < 0) {
kfree(tz);
return ERR_PTR(result);
}
tz->id = result;
strlcpy(tz->type, type, sizeof(tz->type));
tz->ops = ops;
tz->tzp = tzp;
......@@ -1201,7 +1180,7 @@ thermal_zone_device_register(const char *type, int trips, int mask,
dev_set_name(&tz->device, "thermal_zone%d", tz->id);
result = device_register(&tz->device);
if (result) {
release_idr(&thermal_tz_idr, &thermal_idr_lock, tz->id);
ida_simple_remove(&thermal_tz_ida, tz->id);
kfree(tz);
return ERR_PTR(result);
}
......@@ -1255,7 +1234,7 @@ thermal_zone_device_register(const char *type, int trips, int mask,
return tz;
unregister:
release_idr(&thermal_tz_idr, &thermal_idr_lock, tz->id);
ida_simple_remove(&thermal_tz_ida, tz->id);
device_unregister(&tz->device);
return ERR_PTR(result);
}
......@@ -1313,8 +1292,8 @@ void thermal_zone_device_unregister(struct thermal_zone_device *tz)
thermal_set_governor(tz, NULL);
thermal_remove_hwmon_sysfs(tz);
release_idr(&thermal_tz_idr, &thermal_idr_lock, tz->id);
idr_destroy(&tz->idr);
ida_simple_remove(&thermal_tz_ida, tz->id);
ida_destroy(&tz->ida);
mutex_destroy(&tz->lock);
device_unregister(&tz->device);
}
......@@ -1514,9 +1493,8 @@ static int __init thermal_init(void)
unregister_governors:
thermal_unregister_governors();
error:
idr_destroy(&thermal_tz_idr);
idr_destroy(&thermal_cdev_idr);
mutex_destroy(&thermal_idr_lock);
ida_destroy(&thermal_tz_ida);
ida_destroy(&thermal_cdev_ida);
mutex_destroy(&thermal_list_lock);
mutex_destroy(&thermal_governor_lock);
return result;
......@@ -1529,9 +1507,8 @@ static void __exit thermal_exit(void)
genetlink_exit();
class_unregister(&thermal_class);
thermal_unregister_governors();
idr_destroy(&thermal_tz_idr);
idr_destroy(&thermal_cdev_idr);
mutex_destroy(&thermal_idr_lock);
ida_destroy(&thermal_tz_ida);
ida_destroy(&thermal_cdev_ida);
mutex_destroy(&thermal_list_lock);
mutex_destroy(&thermal_governor_lock);
}
......
......@@ -11,7 +11,6 @@ config TI_SOC_THERMAL
config TI_THERMAL
bool "Texas Instruments SoCs thermal framework support"
depends on TI_SOC_THERMAL
depends on CPU_THERMAL
help
If you say yes here you want to get support for generic thermal
framework for the Texas Instruments on die bandgap temperature sensor.
......
......@@ -54,7 +54,6 @@
#define DRA752_STD_FUSE_OPP_BGAP_CORE_OFFSET 0x8
#define DRA752_TEMP_SENSOR_CORE_OFFSET 0x154
#define DRA752_BANDGAP_THRESHOLD_CORE_OFFSET 0x1ac
#define DRA752_BANDGAP_TSHUT_CORE_OFFSET 0x1b8
#define DRA752_BANDGAP_CUMUL_DTEMP_CORE_OFFSET 0x1c4
#define DRA752_DTEMP_CORE_0_OFFSET 0x208
#define DRA752_DTEMP_CORE_1_OFFSET 0x20c
......@@ -66,7 +65,6 @@
#define DRA752_STD_FUSE_OPP_BGAP_IVA_OFFSET 0x388
#define DRA752_TEMP_SENSOR_IVA_OFFSET 0x398
#define DRA752_BANDGAP_THRESHOLD_IVA_OFFSET 0x3a4
#define DRA752_BANDGAP_TSHUT_IVA_OFFSET 0x3ac
#define DRA752_BANDGAP_CUMUL_DTEMP_IVA_OFFSET 0x3b4
#define DRA752_DTEMP_IVA_0_OFFSET 0x3d0
#define DRA752_DTEMP_IVA_1_OFFSET 0x3d4
......@@ -78,7 +76,6 @@
#define DRA752_STD_FUSE_OPP_BGAP_MPU_OFFSET 0x4
#define DRA752_TEMP_SENSOR_MPU_OFFSET 0x14c
#define DRA752_BANDGAP_THRESHOLD_MPU_OFFSET 0x1a4
#define DRA752_BANDGAP_TSHUT_MPU_OFFSET 0x1b0
#define DRA752_BANDGAP_CUMUL_DTEMP_MPU_OFFSET 0x1bc
#define DRA752_DTEMP_MPU_0_OFFSET 0x1e0
#define DRA752_DTEMP_MPU_1_OFFSET 0x1e4
......@@ -90,7 +87,6 @@
#define DRA752_STD_FUSE_OPP_BGAP_DSPEVE_OFFSET 0x384
#define DRA752_TEMP_SENSOR_DSPEVE_OFFSET 0x394
#define DRA752_BANDGAP_THRESHOLD_DSPEVE_OFFSET 0x3a0
#define DRA752_BANDGAP_TSHUT_DSPEVE_OFFSET 0x3a8
#define DRA752_BANDGAP_CUMUL_DTEMP_DSPEVE_OFFSET 0x3b0
#define DRA752_DTEMP_DSPEVE_0_OFFSET 0x3bc
#define DRA752_DTEMP_DSPEVE_1_OFFSET 0x3c0
......@@ -102,7 +98,6 @@
#define DRA752_STD_FUSE_OPP_BGAP_GPU_OFFSET 0x0
#define DRA752_TEMP_SENSOR_GPU_OFFSET 0x150
#define DRA752_BANDGAP_THRESHOLD_GPU_OFFSET 0x1a8
#define DRA752_BANDGAP_TSHUT_GPU_OFFSET 0x1b4
#define DRA752_BANDGAP_CUMUL_DTEMP_GPU_OFFSET 0x1c0
#define DRA752_DTEMP_GPU_0_OFFSET 0x1f4
#define DRA752_DTEMP_GPU_1_OFFSET 0x1f8
......@@ -173,10 +168,6 @@
#define DRA752_BANDGAP_THRESHOLD_HOT_MASK (0x3ff << 16)
#define DRA752_BANDGAP_THRESHOLD_COLD_MASK (0x3ff << 0)
/* DRA752.TSHUT_THRESHOLD */
#define DRA752_TSHUT_THRESHOLD_MUXCTRL_MASK BIT(31)
#define DRA752_TSHUT_THRESHOLD_HOT_MASK (0x3ff << 16)
#define DRA752_TSHUT_THRESHOLD_COLD_MASK (0x3ff << 0)
/* DRA752.BANDGAP_CUMUL_DTEMP_CORE */
#define DRA752_BANDGAP_CUMUL_DTEMP_CORE_MASK (0xffffffff << 0)
......@@ -216,8 +207,6 @@
#define DRA752_GPU_MAX_TEMP 125000
#define DRA752_GPU_HYST_VAL 5000
/* interrupts thresholds */
#define DRA752_GPU_TSHUT_HOT 915
#define DRA752_GPU_TSHUT_COLD 900
#define DRA752_GPU_T_HOT 800
#define DRA752_GPU_T_COLD 795
......@@ -230,8 +219,6 @@
#define DRA752_MPU_MAX_TEMP 125000
#define DRA752_MPU_HYST_VAL 5000
/* interrupts thresholds */
#define DRA752_MPU_TSHUT_HOT 915
#define DRA752_MPU_TSHUT_COLD 900
#define DRA752_MPU_T_HOT 800
#define DRA752_MPU_T_COLD 795
......@@ -244,8 +231,6 @@
#define DRA752_CORE_MAX_TEMP 125000
#define DRA752_CORE_HYST_VAL 5000
/* interrupts thresholds */
#define DRA752_CORE_TSHUT_HOT 915
#define DRA752_CORE_TSHUT_COLD 900
#define DRA752_CORE_T_HOT 800
#define DRA752_CORE_T_COLD 795
......@@ -258,8 +243,6 @@
#define DRA752_DSPEVE_MAX_TEMP 125000
#define DRA752_DSPEVE_HYST_VAL 5000
/* interrupts thresholds */
#define DRA752_DSPEVE_TSHUT_HOT 915
#define DRA752_DSPEVE_TSHUT_COLD 900
#define DRA752_DSPEVE_T_HOT 800
#define DRA752_DSPEVE_T_COLD 795
......@@ -272,8 +255,6 @@
#define DRA752_IVA_MAX_TEMP 125000
#define DRA752_IVA_HYST_VAL 5000
/* interrupts thresholds */
#define DRA752_IVA_TSHUT_HOT 915
#define DRA752_IVA_TSHUT_COLD 900
#define DRA752_IVA_T_HOT 800
#define DRA752_IVA_T_COLD 795
......
......@@ -49,9 +49,6 @@ dra752_core_temp_sensor_registers = {
.bgap_threshold = DRA752_BANDGAP_THRESHOLD_CORE_OFFSET,
.threshold_thot_mask = DRA752_BANDGAP_THRESHOLD_HOT_MASK,
.threshold_tcold_mask = DRA752_BANDGAP_THRESHOLD_COLD_MASK,
.tshut_threshold = DRA752_BANDGAP_TSHUT_CORE_OFFSET,
.tshut_hot_mask = DRA752_TSHUT_THRESHOLD_HOT_MASK,
.tshut_cold_mask = DRA752_TSHUT_THRESHOLD_COLD_MASK,
.bgap_status = DRA752_BANDGAP_STATUS_1_OFFSET,
.status_bgap_alert_mask = DRA752_BANDGAP_STATUS_1_ALERT_MASK,
.status_hot_mask = DRA752_BANDGAP_STATUS_1_HOT_CORE_MASK,
......@@ -85,9 +82,6 @@ dra752_iva_temp_sensor_registers = {
.bgap_threshold = DRA752_BANDGAP_THRESHOLD_IVA_OFFSET,
.threshold_thot_mask = DRA752_BANDGAP_THRESHOLD_HOT_MASK,
.threshold_tcold_mask = DRA752_BANDGAP_THRESHOLD_COLD_MASK,
.tshut_threshold = DRA752_BANDGAP_TSHUT_IVA_OFFSET,
.tshut_hot_mask = DRA752_TSHUT_THRESHOLD_HOT_MASK,
.tshut_cold_mask = DRA752_TSHUT_THRESHOLD_COLD_MASK,
.bgap_status = DRA752_BANDGAP_STATUS_2_OFFSET,
.status_bgap_alert_mask = DRA752_BANDGAP_STATUS_1_ALERT_MASK,
.status_hot_mask = DRA752_BANDGAP_STATUS_2_HOT_IVA_MASK,
......@@ -121,9 +115,6 @@ dra752_mpu_temp_sensor_registers = {
.bgap_threshold = DRA752_BANDGAP_THRESHOLD_MPU_OFFSET,
.threshold_thot_mask = DRA752_BANDGAP_THRESHOLD_HOT_MASK,
.threshold_tcold_mask = DRA752_BANDGAP_THRESHOLD_COLD_MASK,
.tshut_threshold = DRA752_BANDGAP_TSHUT_MPU_OFFSET,
.tshut_hot_mask = DRA752_TSHUT_THRESHOLD_HOT_MASK,
.tshut_cold_mask = DRA752_TSHUT_THRESHOLD_COLD_MASK,
.bgap_status = DRA752_BANDGAP_STATUS_1_OFFSET,
.status_bgap_alert_mask = DRA752_BANDGAP_STATUS_1_ALERT_MASK,
.status_hot_mask = DRA752_BANDGAP_STATUS_1_HOT_MPU_MASK,
......@@ -157,9 +148,6 @@ dra752_dspeve_temp_sensor_registers = {
.bgap_threshold = DRA752_BANDGAP_THRESHOLD_DSPEVE_OFFSET,
.threshold_thot_mask = DRA752_BANDGAP_THRESHOLD_HOT_MASK,
.threshold_tcold_mask = DRA752_BANDGAP_THRESHOLD_COLD_MASK,
.tshut_threshold = DRA752_BANDGAP_TSHUT_DSPEVE_OFFSET,
.tshut_hot_mask = DRA752_TSHUT_THRESHOLD_HOT_MASK,
.tshut_cold_mask = DRA752_TSHUT_THRESHOLD_COLD_MASK,
.bgap_status = DRA752_BANDGAP_STATUS_2_OFFSET,
.status_bgap_alert_mask = DRA752_BANDGAP_STATUS_1_ALERT_MASK,
.status_hot_mask = DRA752_BANDGAP_STATUS_2_HOT_DSPEVE_MASK,
......@@ -193,9 +181,6 @@ dra752_gpu_temp_sensor_registers = {
.bgap_threshold = DRA752_BANDGAP_THRESHOLD_GPU_OFFSET,
.threshold_thot_mask = DRA752_BANDGAP_THRESHOLD_HOT_MASK,
.threshold_tcold_mask = DRA752_BANDGAP_THRESHOLD_COLD_MASK,
.tshut_threshold = DRA752_BANDGAP_TSHUT_GPU_OFFSET,
.tshut_hot_mask = DRA752_TSHUT_THRESHOLD_HOT_MASK,
.tshut_cold_mask = DRA752_TSHUT_THRESHOLD_COLD_MASK,
.bgap_status = DRA752_BANDGAP_STATUS_1_OFFSET,
.status_bgap_alert_mask = DRA752_BANDGAP_STATUS_1_ALERT_MASK,
.status_hot_mask = DRA752_BANDGAP_STATUS_1_HOT_GPU_MASK,
......@@ -211,8 +196,6 @@ dra752_gpu_temp_sensor_registers = {
/* Thresholds and limits for DRA752 MPU temperature sensor */
static struct temp_sensor_data dra752_mpu_temp_sensor_data = {
.tshut_hot = DRA752_MPU_TSHUT_HOT,
.tshut_cold = DRA752_MPU_TSHUT_COLD,
.t_hot = DRA752_MPU_T_HOT,
.t_cold = DRA752_MPU_T_COLD,
.min_freq = DRA752_MPU_MIN_FREQ,
......@@ -226,8 +209,6 @@ static struct temp_sensor_data dra752_mpu_temp_sensor_data = {
/* Thresholds and limits for DRA752 GPU temperature sensor */
static struct temp_sensor_data dra752_gpu_temp_sensor_data = {
.tshut_hot = DRA752_GPU_TSHUT_HOT,
.tshut_cold = DRA752_GPU_TSHUT_COLD,
.t_hot = DRA752_GPU_T_HOT,
.t_cold = DRA752_GPU_T_COLD,
.min_freq = DRA752_GPU_MIN_FREQ,
......@@ -241,8 +222,6 @@ static struct temp_sensor_data dra752_gpu_temp_sensor_data = {
/* Thresholds and limits for DRA752 CORE temperature sensor */
static struct temp_sensor_data dra752_core_temp_sensor_data = {
.tshut_hot = DRA752_CORE_TSHUT_HOT,
.tshut_cold = DRA752_CORE_TSHUT_COLD,
.t_hot = DRA752_CORE_T_HOT,
.t_cold = DRA752_CORE_T_COLD,
.min_freq = DRA752_CORE_MIN_FREQ,
......@@ -256,8 +235,6 @@ static struct temp_sensor_data dra752_core_temp_sensor_data = {
/* Thresholds and limits for DRA752 DSPEVE temperature sensor */
static struct temp_sensor_data dra752_dspeve_temp_sensor_data = {
.tshut_hot = DRA752_DSPEVE_TSHUT_HOT,
.tshut_cold = DRA752_DSPEVE_TSHUT_COLD,
.t_hot = DRA752_DSPEVE_T_HOT,
.t_cold = DRA752_DSPEVE_T_COLD,
.min_freq = DRA752_DSPEVE_MIN_FREQ,
......@@ -271,8 +248,6 @@ static struct temp_sensor_data dra752_dspeve_temp_sensor_data = {
/* Thresholds and limits for DRA752 IVA temperature sensor */
static struct temp_sensor_data dra752_iva_temp_sensor_data = {
.tshut_hot = DRA752_IVA_TSHUT_HOT,
.tshut_cold = DRA752_IVA_TSHUT_COLD,
.t_hot = DRA752_IVA_T_HOT,
.t_cold = DRA752_IVA_T_COLD,
.min_freq = DRA752_IVA_MIN_FREQ,
......@@ -416,8 +391,7 @@ int dra752_adc_to_temp[DRA752_ADC_END_VALUE - DRA752_ADC_START_VALUE + 1] = {
/* DRA752 data */
const struct ti_bandgap_data dra752_data = {
.features = TI_BANDGAP_FEATURE_TSHUT_CONFIG |
TI_BANDGAP_FEATURE_FREEZE_BIT |
.features = TI_BANDGAP_FEATURE_FREEZE_BIT |
TI_BANDGAP_FEATURE_TALERT |
TI_BANDGAP_FEATURE_COUNTER_DELAY |
TI_BANDGAP_FEATURE_HISTORY_BUFFER |
......
/*
* ZTE's zx2967 family thermal sensor driver
*
* Copyright (C) 2017 ZTE Ltd.
*
* Author: Baoyou Xie <baoyou.xie@linaro.org>
*
* License terms: GNU General Public License (GPL) version 2
*/
#include <linux/clk.h>
#include <linux/device.h>
#include <linux/err.h>
#include <linux/iopoll.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/thermal.h>
/* Power Mode: 0->low 1->high */
#define ZX2967_THERMAL_POWER_MODE 0
#define ZX2967_POWER_MODE_LOW 0
#define ZX2967_POWER_MODE_HIGH 1
/* DCF Control Register */
#define ZX2967_THERMAL_DCF 0x4
#define ZX2967_DCF_EN BIT(1)
#define ZX2967_DCF_FREEZE BIT(0)
/* Selection Register */
#define ZX2967_THERMAL_SEL 0x8
/* Control Register */
#define ZX2967_THERMAL_CTRL 0x10
#define ZX2967_THERMAL_READY BIT(12)
#define ZX2967_THERMAL_TEMP_MASK GENMASK(11, 0)
#define ZX2967_THERMAL_ID_MASK 0x18
#define ZX2967_THERMAL_ID 0x10
#define ZX2967_GET_TEMP_TIMEOUT_US (100 * 1024)
/**
* struct zx2967_thermal_priv - zx2967 thermal sensor private structure
* @tzd: struct thermal_zone_device where the sensor is registered
* @lock: prevents read sensor in parallel
* @clk_topcrm: topcrm clk structure
* @clk_apb: apb clk structure
* @regs: pointer to base address of the thermal sensor
*/
struct zx2967_thermal_priv {
struct thermal_zone_device *tzd;
struct mutex lock;
struct clk *clk_topcrm;
struct clk *clk_apb;
void __iomem *regs;
struct device *dev;
};
static int zx2967_thermal_get_temp(void *data, int *temp)
{
void __iomem *regs;
struct zx2967_thermal_priv *priv = data;
u32 val;
int ret;
if (!priv->tzd)
return -EAGAIN;
regs = priv->regs;
mutex_lock(&priv->lock);
writel_relaxed(ZX2967_POWER_MODE_LOW,
regs + ZX2967_THERMAL_POWER_MODE);
writel_relaxed(ZX2967_DCF_EN, regs + ZX2967_THERMAL_DCF);
val = readl_relaxed(regs + ZX2967_THERMAL_SEL);
val &= ~ZX2967_THERMAL_ID_MASK;
val |= ZX2967_THERMAL_ID;
writel_relaxed(val, regs + ZX2967_THERMAL_SEL);
/*
* Must wait for a while, surely it's a bit odd.
* otherwise temperature value we got has a few deviation, even if
* the THERMAL_READY bit is set.
*/
usleep_range(100, 300);
ret = readx_poll_timeout(readl, regs + ZX2967_THERMAL_CTRL,
val, val & ZX2967_THERMAL_READY, 300,
ZX2967_GET_TEMP_TIMEOUT_US);
if (ret) {
dev_err(priv->dev, "Thermal sensor data timeout\n");
goto unlock;
}
writel_relaxed(ZX2967_DCF_FREEZE | ZX2967_DCF_EN,
regs + ZX2967_THERMAL_DCF);
val = readl_relaxed(regs + ZX2967_THERMAL_CTRL)
& ZX2967_THERMAL_TEMP_MASK;
writel_relaxed(ZX2967_POWER_MODE_HIGH,
regs + ZX2967_THERMAL_POWER_MODE);
/*
* Calculate temperature
* In dts, slope is multiplied by 1000.
*/
*temp = DIV_ROUND_CLOSEST(((s32)val + priv->tzd->tzp->offset) * 1000,
priv->tzd->tzp->slope);
unlock:
mutex_unlock(&priv->lock);
return ret;
}
static struct thermal_zone_of_device_ops zx2967_of_thermal_ops = {
.get_temp = zx2967_thermal_get_temp,
};
static int zx2967_thermal_probe(struct platform_device *pdev)
{
struct zx2967_thermal_priv *priv;
struct resource *res;
int ret;
priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
if (!priv)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
priv->regs = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(priv->regs))
return PTR_ERR(priv->regs);
priv->clk_topcrm = devm_clk_get(&pdev->dev, "topcrm");
if (IS_ERR(priv->clk_topcrm)) {
ret = PTR_ERR(priv->clk_topcrm);
dev_err(&pdev->dev, "failed to get topcrm clock: %d\n", ret);
return ret;
}
ret = clk_prepare_enable(priv->clk_topcrm);
if (ret) {
dev_err(&pdev->dev, "failed to enable topcrm clock: %d\n",
ret);
return ret;
}
priv->clk_apb = devm_clk_get(&pdev->dev, "apb");
if (IS_ERR(priv->clk_apb)) {
ret = PTR_ERR(priv->clk_apb);
dev_err(&pdev->dev, "failed to get apb clock: %d\n", ret);
goto disable_clk_topcrm;
}
ret = clk_prepare_enable(priv->clk_apb);
if (ret) {
dev_err(&pdev->dev, "failed to enable apb clock: %d\n",
ret);
goto disable_clk_topcrm;
}
mutex_init(&priv->lock);
priv->tzd = thermal_zone_of_sensor_register(&pdev->dev,
0, priv, &zx2967_of_thermal_ops);
if (IS_ERR(priv->tzd)) {
ret = PTR_ERR(priv->tzd);
dev_err(&pdev->dev, "failed to register sensor: %d\n", ret);
goto disable_clk_all;
}
if (priv->tzd->tzp->slope == 0) {
thermal_zone_of_sensor_unregister(&pdev->dev, priv->tzd);
dev_err(&pdev->dev, "coefficients of sensor is invalid\n");
ret = -EINVAL;
goto disable_clk_all;
}
priv->dev = &pdev->dev;
platform_set_drvdata(pdev, priv);
return 0;
disable_clk_all:
clk_disable_unprepare(priv->clk_apb);
disable_clk_topcrm:
clk_disable_unprepare(priv->clk_topcrm);
return ret;
}
static int zx2967_thermal_exit(struct platform_device *pdev)
{
struct zx2967_thermal_priv *priv = platform_get_drvdata(pdev);
thermal_zone_of_sensor_unregister(&pdev->dev, priv->tzd);
clk_disable_unprepare(priv->clk_topcrm);
clk_disable_unprepare(priv->clk_apb);
return 0;
}
static const struct of_device_id zx2967_thermal_id_table[] = {
{ .compatible = "zte,zx296718-thermal" },
{}
};
MODULE_DEVICE_TABLE(of, zx2967_thermal_id_table);
#ifdef CONFIG_PM_SLEEP
static int zx2967_thermal_suspend(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
struct zx2967_thermal_priv *priv = platform_get_drvdata(pdev);
if (priv && priv->clk_topcrm)
clk_disable_unprepare(priv->clk_topcrm);
if (priv && priv->clk_apb)
clk_disable_unprepare(priv->clk_apb);
return 0;
}
static int zx2967_thermal_resume(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
struct zx2967_thermal_priv *priv = platform_get_drvdata(pdev);
int error;
error = clk_prepare_enable(priv->clk_topcrm);
if (error)
return error;
error = clk_prepare_enable(priv->clk_apb);
if (error) {
clk_disable_unprepare(priv->clk_topcrm);
return error;
}
return 0;
}
#endif
static SIMPLE_DEV_PM_OPS(zx2967_thermal_pm_ops,
zx2967_thermal_suspend, zx2967_thermal_resume);
static struct platform_driver zx2967_thermal_driver = {
.probe = zx2967_thermal_probe,
.remove = zx2967_thermal_exit,
.driver = {
.name = "zx2967_thermal",
.of_match_table = zx2967_thermal_id_table,
.pm = &zx2967_thermal_pm_ops,
},
};
module_platform_driver(zx2967_thermal_driver);
MODULE_AUTHOR("Baoyou Xie <baoyou.xie@linaro.org>");
MODULE_DESCRIPTION("ZTE zx2967 thermal driver");
MODULE_LICENSE("GPL v2");
......@@ -194,7 +194,7 @@ struct thermal_attr {
* @governor: pointer to the governor for this thermal zone
* @governor_data: private pointer for governor data
* @thermal_instances: list of &struct thermal_instance of this thermal zone
* @idr: &struct idr to generate unique id for this zone's cooling
* @ida: &struct ida to generate unique id for this zone's cooling
* devices
* @lock: lock to protect thermal_instances list
* @node: node in thermal_tz_list (in thermal_core.c)
......@@ -227,7 +227,7 @@ struct thermal_zone_device {
struct thermal_governor *governor;
void *governor_data;
struct list_head thermal_instances;
struct idr idr;
struct ida ida;
struct mutex lock;
struct list_head node;
struct delayed_work poll_queue;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment