Commit 71354661 authored by Arnd Bergmann's avatar Arnd Bergmann

Merge branch 'brcm/stb-smp-uart' into next/drivers

This resolves a nonobvious merge conflict that I got wrong the
first time.

* brcm/stb-smp-uart:
  bus: brcmstb_gisb: save and restore GISB timeout
  bus: brcmstb_gisb: register the fault code hook
  ARM: brcmstb: Kconfig: drop unneeded symbol selections
  ARM: brcmstb: reintroduce SMP support
  ARM: brcmstb: add debug UART for earlyprintk support

Conflicts:
	drivers/bus/brcmstb_gisb.c
Signed-off-by: default avatarArnd Bergmann <arnd@arndb.de>
Reported-by: default avatarFlorian Fainelli <f.fainelli@gmail.com>
parents 6b34df9e 203bb85e
......@@ -139,6 +139,17 @@ choice
Say Y here if you want kernel low-level debugging support
on Marvell Berlin SoC based platforms.
config DEBUG_BRCMSTB_UART
bool "Use BRCMSTB UART for low-level debug"
depends on ARCH_BRCMSTB
select DEBUG_UART_8250
help
Say Y here if you want the debug print routines to direct
their output to the first serial port on these devices.
If you have a Broadcom STB chip and would like early print
messages to appear over the UART, select this option.
config DEBUG_CLPS711X_UART1
bool "Kernel low-level debugging messages via UART1"
depends on ARCH_CLPS711X
......@@ -1153,6 +1164,7 @@ config DEBUG_UART_PHYS
default 0xe0000000 if ARCH_SPEAR13XX
default 0xe4007000 if DEBUG_HIP04_UART
default 0xf0000be0 if ARCH_EBSA110
default 0xf040ab00 if DEBUG_BRCMSTB_UART
default 0xf1012000 if DEBUG_MVEBU_UART_ALTERNATE
default 0xf1012000 if ARCH_DOVE || ARCH_MV78XX0 || \
ARCH_ORION5X
......@@ -1204,6 +1216,7 @@ config DEBUG_UART_VIRT
default 0xfb002000 if DEBUG_CNS3XXX
default 0xfb009000 if DEBUG_REALVIEW_STD_PORT
default 0xfb10c000 if DEBUG_REALVIEW_PB1176_PORT
default 0xfc40ab00 if DEBUG_BRCMSTB_UART
default 0xfcfe8600 if DEBUG_UART_BCM63XX
default 0xfd000000 if ARCH_SPEAR3XX || ARCH_SPEAR6XX
default 0xfd000000 if ARCH_SPEAR13XX
......@@ -1260,7 +1273,8 @@ config DEBUG_UART_8250_WORD
ARCH_KEYSTONE || \
DEBUG_DAVINCI_DMx_UART0 || DEBUG_DAVINCI_DA8XX_UART1 || \
DEBUG_DAVINCI_DA8XX_UART2 || \
DEBUG_BCM_KONA_UART || DEBUG_RK32_UART2
DEBUG_BCM_KONA_UART || DEBUG_RK32_UART2 || \
DEBUG_BRCMSTB_UART
config DEBUG_UART_8250_FLOW_CONTROL
bool "Enable flow control for 8250 UART"
......
......@@ -118,10 +118,7 @@ config ARCH_BCM_63XX
config ARCH_BRCMSTB
bool "Broadcom BCM7XXX based boards" if ARCH_MULTI_V7
depends on MMU
select ARM_GIC
select MIGHT_HAVE_PCI
select HAVE_SMP
select HAVE_ARM_ARCH_TIMER
select BRCMSTB_GISB_ARB
select BRCMSTB_L2_IRQ
......
......@@ -38,5 +38,7 @@ obj-$(CONFIG_ARCH_BCM_5301X) += bcm_5301x.o
obj-$(CONFIG_ARCH_BCM_63XX) := bcm63xx.o
ifeq ($(CONFIG_ARCH_BRCMSTB),y)
CFLAGS_platsmp-brcmstb.o += -march=armv7-a
obj-y += brcmstb.o
obj-$(CONFIG_SMP) += headsmp-brcmstb.o platsmp-brcmstb.o
endif
/*
* Copyright (C) 2013-2014 Broadcom Corporation
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation version 2.
*
* This program is distributed "as is" WITHOUT ANY WARRANTY of any
* kind, whether express or implied; without even the implied warranty
* of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#ifndef __BRCMSTB_H__
#define __BRCMSTB_H__
void brcmstb_secondary_startup(void);
#endif /* __BRCMSTB_H__ */
/*
* SMP boot code for secondary CPUs
* Based on arch/arm/mach-tegra/headsmp.S
*
* Copyright (C) 2010 NVIDIA, Inc.
* Copyright (C) 2013-2014 Broadcom Corporation
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation version 2.
*
* This program is distributed "as is" WITHOUT ANY WARRANTY of any
* kind, whether express or implied; without even the implied warranty
* of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <asm/assembler.h>
#include <linux/linkage.h>
#include <linux/init.h>
.section ".text.head", "ax"
ENTRY(brcmstb_secondary_startup)
/*
* Ensure CPU is in a sane state by disabling all IRQs and switching
* into SVC mode.
*/
setmode PSR_I_BIT | PSR_F_BIT | SVC_MODE, r0
bl v7_invalidate_l1
b secondary_startup
ENDPROC(brcmstb_secondary_startup)
/*
* Broadcom STB CPU SMP and hotplug support for ARM
*
* Copyright (C) 2013-2014 Broadcom Corporation
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation version 2.
*
* This program is distributed "as is" WITHOUT ANY WARRANTY of any
* kind, whether express or implied; without even the implied warranty
* of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/delay.h>
#include <linux/errno.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/of_address.h>
#include <linux/of_platform.h>
#include <linux/printk.h>
#include <linux/regmap.h>
#include <linux/smp.h>
#include <linux/mfd/syscon.h>
#include <asm/cacheflush.h>
#include <asm/cp15.h>
#include <asm/mach-types.h>
#include <asm/smp_plat.h>
#include "brcmstb.h"
enum {
ZONE_MAN_CLKEN_MASK = BIT(0),
ZONE_MAN_RESET_CNTL_MASK = BIT(1),
ZONE_MAN_MEM_PWR_MASK = BIT(4),
ZONE_RESERVED_1_MASK = BIT(5),
ZONE_MAN_ISO_CNTL_MASK = BIT(6),
ZONE_MANUAL_CONTROL_MASK = BIT(7),
ZONE_PWR_DN_REQ_MASK = BIT(9),
ZONE_PWR_UP_REQ_MASK = BIT(10),
ZONE_BLK_RST_ASSERT_MASK = BIT(12),
ZONE_PWR_OFF_STATE_MASK = BIT(25),
ZONE_PWR_ON_STATE_MASK = BIT(26),
ZONE_DPG_PWR_STATE_MASK = BIT(28),
ZONE_MEM_PWR_STATE_MASK = BIT(29),
ZONE_RESET_STATE_MASK = BIT(31),
CPU0_PWR_ZONE_CTRL_REG = 1,
CPU_RESET_CONFIG_REG = 2,
};
static void __iomem *cpubiuctrl_block;
static void __iomem *hif_cont_block;
static u32 cpu0_pwr_zone_ctrl_reg;
static u32 cpu_rst_cfg_reg;
static u32 hif_cont_reg;
#ifdef CONFIG_HOTPLUG_CPU
/*
* We must quiesce a dying CPU before it can be killed by the boot CPU. Because
* one or more cache may be disabled, we must flush to ensure coherency. We
* cannot use traditionl completion structures or spinlocks as they rely on
* coherency.
*/
static DEFINE_PER_CPU_ALIGNED(int, per_cpu_sw_state);
static int per_cpu_sw_state_rd(u32 cpu)
{
sync_cache_r(SHIFT_PERCPU_PTR(&per_cpu_sw_state, per_cpu_offset(cpu)));
return per_cpu(per_cpu_sw_state, cpu);
}
static void per_cpu_sw_state_wr(u32 cpu, int val)
{
dmb();
per_cpu(per_cpu_sw_state, cpu) = val;
sync_cache_w(SHIFT_PERCPU_PTR(&per_cpu_sw_state, per_cpu_offset(cpu)));
}
#else
static inline void per_cpu_sw_state_wr(u32 cpu, int val) { }
#endif
static void __iomem *pwr_ctrl_get_base(u32 cpu)
{
void __iomem *base = cpubiuctrl_block + cpu0_pwr_zone_ctrl_reg;
base += (cpu_logical_map(cpu) * 4);
return base;
}
static u32 pwr_ctrl_rd(u32 cpu)
{
void __iomem *base = pwr_ctrl_get_base(cpu);
return readl_relaxed(base);
}
static void pwr_ctrl_wr(u32 cpu, u32 val)
{
void __iomem *base = pwr_ctrl_get_base(cpu);
writel(val, base);
}
static void cpu_rst_cfg_set(u32 cpu, int set)
{
u32 val;
val = readl_relaxed(cpubiuctrl_block + cpu_rst_cfg_reg);
if (set)
val |= BIT(cpu_logical_map(cpu));
else
val &= ~BIT(cpu_logical_map(cpu));
writel_relaxed(val, cpubiuctrl_block + cpu_rst_cfg_reg);
}
static void cpu_set_boot_addr(u32 cpu, unsigned long boot_addr)
{
const int reg_ofs = cpu_logical_map(cpu) * 8;
writel_relaxed(0, hif_cont_block + hif_cont_reg + reg_ofs);
writel_relaxed(boot_addr, hif_cont_block + hif_cont_reg + 4 + reg_ofs);
}
static void brcmstb_cpu_boot(u32 cpu)
{
/* Mark this CPU as "up" */
per_cpu_sw_state_wr(cpu, 1);
/*
* Set the reset vector to point to the secondary_startup
* routine
*/
cpu_set_boot_addr(cpu, virt_to_phys(brcmstb_secondary_startup));
/* Unhalt the cpu */
cpu_rst_cfg_set(cpu, 0);
}
static void brcmstb_cpu_power_on(u32 cpu)
{
/*
* The secondary cores power was cut, so we must go through
* power-on initialization.
*/
u32 tmp;
/* Request zone power up */
pwr_ctrl_wr(cpu, ZONE_PWR_UP_REQ_MASK);
/* Wait for the power up FSM to complete */
do {
tmp = pwr_ctrl_rd(cpu);
} while (!(tmp & ZONE_PWR_ON_STATE_MASK));
}
static int brcmstb_cpu_get_power_state(u32 cpu)
{
int tmp = pwr_ctrl_rd(cpu);
return (tmp & ZONE_RESET_STATE_MASK) ? 0 : 1;
}
#ifdef CONFIG_HOTPLUG_CPU
static void brcmstb_cpu_die(u32 cpu)
{
v7_exit_coherency_flush(all);
per_cpu_sw_state_wr(cpu, 0);
/* Sit and wait to die */
wfi();
/* We should never get here... */
while (1)
;
}
static int brcmstb_cpu_kill(u32 cpu)
{
u32 tmp;
while (per_cpu_sw_state_rd(cpu))
;
/* Program zone reset */
pwr_ctrl_wr(cpu, ZONE_RESET_STATE_MASK | ZONE_BLK_RST_ASSERT_MASK |
ZONE_PWR_DN_REQ_MASK);
/* Verify zone reset */
tmp = pwr_ctrl_rd(cpu);
if (!(tmp & ZONE_RESET_STATE_MASK))
pr_err("%s: Zone reset bit for CPU %d not asserted!\n",
__func__, cpu);
/* Wait for power down */
do {
tmp = pwr_ctrl_rd(cpu);
} while (!(tmp & ZONE_PWR_OFF_STATE_MASK));
/* Flush pipeline before resetting CPU */
mb();
/* Assert reset on the CPU */
cpu_rst_cfg_set(cpu, 1);
return 1;
}
#endif /* CONFIG_HOTPLUG_CPU */
static int __init setup_hifcpubiuctrl_regs(struct device_node *np)
{
int rc = 0;
char *name;
struct device_node *syscon_np = NULL;
name = "syscon-cpu";
syscon_np = of_parse_phandle(np, name, 0);
if (!syscon_np) {
pr_err("can't find phandle %s\n", name);
rc = -EINVAL;
goto cleanup;
}
cpubiuctrl_block = of_iomap(syscon_np, 0);
if (!cpubiuctrl_block) {
pr_err("iomap failed for cpubiuctrl_block\n");
rc = -EINVAL;
goto cleanup;
}
rc = of_property_read_u32_index(np, name, CPU0_PWR_ZONE_CTRL_REG,
&cpu0_pwr_zone_ctrl_reg);
if (rc) {
pr_err("failed to read 1st entry from %s property (%d)\n", name,
rc);
rc = -EINVAL;
goto cleanup;
}
rc = of_property_read_u32_index(np, name, CPU_RESET_CONFIG_REG,
&cpu_rst_cfg_reg);
if (rc) {
pr_err("failed to read 2nd entry from %s property (%d)\n", name,
rc);
rc = -EINVAL;
goto cleanup;
}
cleanup:
of_node_put(syscon_np);
return rc;
}
static int __init setup_hifcont_regs(struct device_node *np)
{
int rc = 0;
char *name;
struct device_node *syscon_np = NULL;
name = "syscon-cont";
syscon_np = of_parse_phandle(np, name, 0);
if (!syscon_np) {
pr_err("can't find phandle %s\n", name);
rc = -EINVAL;
goto cleanup;
}
hif_cont_block = of_iomap(syscon_np, 0);
if (!hif_cont_block) {
pr_err("iomap failed for hif_cont_block\n");
rc = -EINVAL;
goto cleanup;
}
/* Offset is at top of hif_cont_block */
hif_cont_reg = 0;
cleanup:
of_node_put(syscon_np);
return rc;
}
static void __init brcmstb_cpu_ctrl_setup(unsigned int max_cpus)
{
int rc;
struct device_node *np;
char *name;
name = "brcm,brcmstb-smpboot";
np = of_find_compatible_node(NULL, NULL, name);
if (!np) {
pr_err("can't find compatible node %s\n", name);
return;
}
rc = setup_hifcpubiuctrl_regs(np);
if (rc)
return;
rc = setup_hifcont_regs(np);
if (rc)
return;
}
static int brcmstb_boot_secondary(unsigned int cpu, struct task_struct *idle)
{
/* Missing the brcm,brcmstb-smpboot DT node? */
if (!cpubiuctrl_block || !hif_cont_block)
return -ENODEV;
/* Bring up power to the core if necessary */
if (brcmstb_cpu_get_power_state(cpu) == 0)
brcmstb_cpu_power_on(cpu);
brcmstb_cpu_boot(cpu);
return 0;
}
static struct smp_operations brcmstb_smp_ops __initdata = {
.smp_prepare_cpus = brcmstb_cpu_ctrl_setup,
.smp_boot_secondary = brcmstb_boot_secondary,
#ifdef CONFIG_HOTPLUG_CPU
.cpu_kill = brcmstb_cpu_kill,
.cpu_die = brcmstb_cpu_die,
#endif
};
CPU_METHOD_OF_DECLARE(brcmstb_smp, "brcm,brahma-b15", &brcmstb_smp_ops);
......@@ -23,6 +23,7 @@
#include <linux/list.h>
#include <linux/of.h>
#include <linux/bitops.h>
#include <linux/pm.h>
#ifdef CONFIG_ARM
#include <asm/bug.h>
......@@ -94,6 +95,7 @@ struct brcmstb_gisb_arb_device {
struct list_head next;
u32 valid_mask;
const char *master_names[sizeof(u32) * BITS_PER_BYTE];
u32 saved_timeout;
};
static LIST_HEAD(brcmstb_gisb_arb_device_list);
......@@ -226,12 +228,6 @@ static int brcmstb_bus_error_handler(unsigned long addr, unsigned int fsr,
return ret;
}
void __init brcmstb_hook_fault_code(void)
{
hook_fault_code(22, brcmstb_bus_error_handler, SIGBUS, 0,
"imprecise external abort");
}
#endif
static irqreturn_t brcmstb_gisb_timeout_handler(int irq, void *dev_id)
......@@ -346,17 +342,56 @@ static int __init brcmstb_gisb_arb_probe(struct platform_device *pdev)
list_add_tail(&gdev->next, &brcmstb_gisb_arb_device_list);
#ifdef CONFIG_ARM
hook_fault_code(22, brcmstb_bus_error_handler, SIGBUS, 0,
"imprecise external abort");
#endif
dev_info(&pdev->dev, "registered mem: %p, irqs: %d, %d\n",
gdev->base, timeout_irq, tea_irq);
return 0;
}
#ifdef CONFIG_PM_SLEEP
static int brcmstb_gisb_arb_suspend(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
struct brcmstb_gisb_arb_device *gdev = platform_get_drvdata(pdev);
gdev->saved_timeout = gisb_read(gdev, ARB_TIMER);
return 0;
}
/* Make sure we provide the same timeout value that was configured before, and
* do this before the GISB timeout interrupt handler has any chance to run.
*/
static int brcmstb_gisb_arb_resume_noirq(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
struct brcmstb_gisb_arb_device *gdev = platform_get_drvdata(pdev);
gisb_write(gdev, gdev->saved_timeout, ARB_TIMER);
return 0;
}
#else
#define brcmstb_gisb_arb_suspend NULL
#define brcmstb_gisb_arb_resume_noirq NULL
#endif
static const struct dev_pm_ops brcmstb_gisb_arb_pm_ops = {
.suspend = brcmstb_gisb_arb_suspend,
.resume_noirq = brcmstb_gisb_arb_resume_noirq,
};
static struct platform_driver brcmstb_gisb_arb_driver = {
.driver = {
.name = "brcm-gisb-arb",
.owner = THIS_MODULE,
.of_match_table = brcmstb_gisb_arb_of_match,
.pm = &brcmstb_gisb_arb_pm_ops,
},
};
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment