Merge branch 'net-dsa-qca8k-Improve-SGMII-interface-handling'

Jonathan McDowell says:

====================
net: dsa: qca8k: Improve SGMII interface handling

This 3 patch series migrates the qca8k switch driver over to PHYLINK,
and then adds the SGMII clean-ups (i.e. the missing initialisation) on
top of that as a second patch. The final patch is a simple spelling fix
in a comment.

As before, tested with a device where the CPU connection is RGMII (i.e.
the common current use case) + one where the CPU connection is SGMII. I
don't have any devices where the SGMII interface is brought out to
something other than the CPU.

v5:
- Move spelling fix to separate patch
- Use ds directly rather than ds->priv
v4:
- Enable pcs_poll so we keep phylink updated when doing in-band
  negotiation
- Explicitly check for PHY_INTERFACE_MODE_1000BASEX when setting SGMII
  port mode.
- Address Vladimir's review comments
v3:
- Move phylink changes to separate patch
- Address rmk review comments
v2:
- Switch to phylink
- Avoid need for device tree configuration options
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/dsa/qca8k.h

@@ -36,6 +36,8 @@
 #define   QCA8K_MAX_DELAY				3
 #define   QCA8K_PORT_PAD_RGMII_RX_DELAY_EN		BIT(24)
 #define   QCA8K_PORT_PAD_SGMII_EN			BIT(7)
+#define QCA8K_REG_PWS					0x010
+#define   QCA8K_PWS_SERDES_AEN_DIS			BIT(7)
 #define QCA8K_REG_MODULE_EN				0x030
 #define   QCA8K_MODULE_EN_MIB				BIT(0)
 #define QCA8K_REG_MIB					0x034
@@ -69,6 +71,7 @@
 #define   QCA8K_PORT_STATUS_LINK_UP			BIT(8)
 #define   QCA8K_PORT_STATUS_LINK_AUTO			BIT(9)
 #define   QCA8K_PORT_STATUS_LINK_PAUSE			BIT(10)
+#define   QCA8K_PORT_STATUS_FLOW_AUTO			BIT(12)
 #define QCA8K_REG_PORT_HDR_CTRL(_i)			(0x9c + (_i * 4))
 #define   QCA8K_PORT_HDR_CTRL_RX_MASK			GENMASK(3, 2)
 #define   QCA8K_PORT_HDR_CTRL_RX_S			2
@@ -77,6 +80,16 @@
 #define   QCA8K_PORT_HDR_CTRL_ALL			2
 #define   QCA8K_PORT_HDR_CTRL_MGMT			1
 #define   QCA8K_PORT_HDR_CTRL_NONE			0
+#define QCA8K_REG_SGMII_CTRL				0x0e0
+#define   QCA8K_SGMII_EN_PLL				BIT(1)
+#define   QCA8K_SGMII_EN_RX				BIT(2)
+#define   QCA8K_SGMII_EN_TX				BIT(3)
+#define   QCA8K_SGMII_EN_SD				BIT(4)
+#define   QCA8K_SGMII_CLK125M_DELAY			BIT(7)
+#define   QCA8K_SGMII_MODE_CTRL_MASK			(BIT(22) | BIT(23))
+#define   QCA8K_SGMII_MODE_CTRL_BASEX			(0 << 22)
+#define   QCA8K_SGMII_MODE_CTRL_PHY			(1 << 22)
+#define   QCA8K_SGMII_MODE_CTRL_MAC			(2 << 22)
 
 /* EEE control registers */
 #define QCA8K_REG_EEE_CTRL				0x100