Commit 75318327 authored by Yaniv Rosner's avatar Yaniv Rosner Committed by David S. Miller

bnx2x: Remove 100Mb force speed for BCM84833

Remove unsupported speed of 100Mb force for BCM84833 due to hardware
limitation.
Signed-off-by: default avatarYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: default avatarEilon Greenstein <eilong@broadcom.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 127302bb
......@@ -365,13 +365,18 @@ static int bnx2x_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
DP(NETIF_MSG_LINK, "cfg_idx = %x\n", cfg_idx);
if (cmd->autoneg == AUTONEG_ENABLE) {
u32 an_supported_speed = bp->port.supported[cfg_idx];
if (bp->link_params.phy[EXT_PHY1].type ==
PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833)
an_supported_speed |= (SUPPORTED_100baseT_Half |
SUPPORTED_100baseT_Full);
if (!(bp->port.supported[cfg_idx] & SUPPORTED_Autoneg)) {
DP(NETIF_MSG_LINK, "Autoneg not supported\n");
return -EINVAL;
}
/* advertise the requested speed and duplex if supported */
if (cmd->advertising & ~(bp->port.supported[cfg_idx])) {
if (cmd->advertising & ~an_supported_speed) {
DP(NETIF_MSG_LINK, "Advertisement parameters "
"are not supported\n");
return -EINVAL;
......
......@@ -9454,13 +9454,10 @@ static int bnx2x_848xx_cmn_config_init(struct bnx2x_phy *phy,
an_1000_val);
/* set 100 speed advertisement */
if (((phy->req_line_speed == SPEED_AUTO_NEG) &&
if ((phy->req_line_speed == SPEED_AUTO_NEG) &&
(phy->speed_cap_mask &
(PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_FULL |
PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_HALF)) &&
(phy->supported &
(SUPPORTED_100baseT_Half |
SUPPORTED_100baseT_Full)))) {
PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_HALF))) {
an_10_100_val |= (1<<7);
/* Enable autoneg and restart autoneg for legacy speeds */
autoneg_val |= (1<<9 | 1<<12);
......@@ -11528,6 +11525,19 @@ static int bnx2x_populate_ext_phy(struct bnx2x *bp,
}
phy->mdio_ctrl = bnx2x_get_emac_base(bp, mdc_mdio_access, port);
if ((phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833) &&
(phy->ver_addr)) {
/*
* Remove 100Mb link supported for BCM84833 when phy fw
* version lower than or equal to 1.39
*/
u32 raw_ver = REG_RD(bp, phy->ver_addr);
if (((raw_ver & 0x7F) <= 39) &&
(((raw_ver & 0xF80) >> 7) <= 1))
phy->supported &= ~(SUPPORTED_100baseT_Half |
SUPPORTED_100baseT_Full);
}
/*
* In case mdc/mdio_access of the external phy is different than the
* mdc/mdio access of the XGXS, a HW lock must be taken in each access
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment