Fix spelling errors in Documentation/devicetree

Signed-off-by: Otto Kekäläinen <otto@seravo.fi>
Signed-off-by: Rob Herring <robh@kernel.org>

Documentation/devicetree/bindings/arm/l2c2x0.txt

@@ -86,10 +86,10 @@ Optional properties:
   firmware)
 - arm,dynamic-clock-gating : L2 dynamic clock gating. Value: <0> (forcibly
   disable), <1> (forcibly enable), property absent (OS specific behavior,
-  preferrably retain firmware settings)
+  preferably retain firmware settings)
 - arm,standby-mode: L2 standby mode enable. Value <0> (forcibly disable),
   <1> (forcibly enable), property absent (OS specific behavior,
-  preferrably retain firmware settings)
+  preferably retain firmware settings)
 
 Example:
 

Documentation/devicetree/bindings/net/dsa/dsa.txt

@@ -43,7 +43,7 @@ Each port children node must have the following mandatory properties:
 Note that a port labelled "dsa" will imply checking for the uplink phandle
 described below.
 
-Optionnal property:
+Optional property:
 - link			: Should be a list of phandles to another switch's DSA port.
 			  This property is only used when switches are being
 			  chained/cascaded together. This port is used as outgoing port

Documentation/devicetree/bindings/powerpc/fsl/fman.txt

@@ -35,7 +35,7 @@ PROPERTIES
 		Definition: Specifies the index of the FMan unit.
 
 		The cell-index value may be used by the SoC, to identify the
-		FMan unit in the SoC memory map. In the table bellow,
+		FMan unit in the SoC memory map. In the table below,
 		there's a description of the cell-index use in each SoC:
 
 		- P1023:
@@ -247,7 +247,7 @@ PROPERTIES
 
 		The cell-index value may be used by the FMan or the SoC, to
 		identify the MAC unit in the FMan (or SoC) memory map.
-		In the tables bellow there's a description of the cell-index
+		In the tables below there's a description of the cell-index
 		use, there are two tables, one describes the use of cell-index
 		by the FMan, the second describes the use by the SoC:
 

Documentation/devicetree/bindings/regmap/regmap.txt

@@ -14,7 +14,7 @@ architectures that typically run big-endian operating systems
 be marked that way in the devicetree.
 
 On SoCs that can be operated in both big-endian and little-endian
-modes, with a single hardware switch controlling both the endianess
+modes, with a single hardware switch controlling both the endianness
 of the CPU and a byteswap for MMIO registers (e.g. many Broadcom MIPS
 chips), "native-endian" is used to allow using the same device tree
 blob in both cases.

Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt

@@ -28,10 +28,10 @@ Optional properties:
 - dma-names: Should contain "tx" for transmit and "rx" for receive channels
 - qcom,tx-crci: Identificator <u32> for Client Rate Control Interface to be
            used with TX DMA channel. Required when using DMA for transmission
-           with UARTDM v1.3 and bellow.
+           with UARTDM v1.3 and below.
 - qcom,rx-crci: Identificator <u32> for Client Rate Control Interface to be
            used with RX DMA channel. Required when using DMA for reception
-           with UARTDM v1.3 and bellow.
+           with UARTDM v1.3 and below.
 
 Note: Aliases may be defined to ensure the correct ordering of the UARTs.
 The alias serialN will result in the UART being assigned port N.  If any

Documentation/devicetree/bindings/sound/simple-card.txt

@@ -30,7 +30,7 @@ Optional subnodes:
 					  sub-nodes. This container may be
 					  omitted when the card has only one
 					  DAI link. See the examples and the
-					  section bellow.
+					  section below.
 
 Dai-link subnode properties and subnodes:
 

Documentation/devicetree/bindings/spi/ti_qspi.txt

@@ -20,7 +20,7 @@ Optional properties:
 		      chipselect register and offset of that register.
 
 NOTE: TI QSPI controller requires different pinmux and IODelay
-paramaters for Mode-0 and Mode-3 operations, which needs to be set up by
+parameters for Mode-0 and Mode-3 operations, which needs to be set up by
 the bootloader (U-Boot). Default configuration only supports Mode-0
 operation. Hence, "spi-cpol" and "spi-cpha" DT properties cannot be
 specified in the slave nodes of TI QSPI controller without appropriate

Documentation/devicetree/bindings/timer/allwinner,sun5i-a13-hstimer.txt

@@ -9,7 +9,7 @@ Required properties:
 		one)
 - clocks: phandle to the source clock (usually the AHB clock)
 
-Optionnal properties:
+Optional properties:
 - resets: phandle to a reset controller asserting the timer
 
 Example: