Merge tag 'boards-3.11-2' of git://git.infradead.org/users/jcooper/linux into next/boards

From Jason Cooper, mvebu board changes for v3.11.
Signed-off-by: Olof Johansson <olof@lixom.net>

* tag 'boards-3.11-2' of git://git.infradead.org/users/jcooper/linux:
  ARM: Kirkwood: Convert LSXL to restart-poweroff driver.
  ARM: Kirkwood: Make use of the QNAP Power off driver.
  ARM: Kirkwood: add DT support for Sheevaplug and Sheevaplug eSATA

arch/arm/boot/dts/kirkwood-lsxl.dtsi

@@ -172,6 +172,10 @@ gpio_fan {
 		alarm-gpios = <&gpio1 8 0>;
 	};
 
+	restart_poweroff {
+		compatible = "restart-poweroff";
+	};
+
 	regulators {
 		compatible = "simple-bus";
 		#address-cells = <1>;

arch/arm/boot/dts/kirkwood-ts219.dtsi

@@ -31,6 +31,11 @@ serial@12100 {
 			clock-frequency = <200000000>;
 			status = "okay";
 		};
+		poweroff@12100 {
+			compatible = "qnap,power-off";
+			reg = <0x12000 0x100>;
+			clocks = <&gate_clk 7>;
+		};
 		spi@10600 {
 			status = "okay";
 

arch/arm/mach-kirkwood/Kconfig

@@ -227,6 +227,7 @@ config MACH_KM_KIRKWOOD_DT
 config MACH_LSXL_DT
 	bool "Buffalo Linkstation LS-XHL, LS-CHLv2 (Flattened Device Tree)"
 	select ARCH_KIRKWOOD_DT
+	select POWER_RESET_RESTART
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Buffalo Linkstation LS-XHL & LS-CHLv2 devices, using
@@ -296,6 +297,13 @@ config MACH_READYNAS_DT
 	  Say 'Y' here if you want your kernel to support the
 	  NETGEAR ReadyNAS Duo v2 using Fattened Device Tree.
 
+config MACH_SHEEVAPLUG_DT
+	bool "Marvell (eSATA) SheevaPlug (Flattened Device Tree)"
+	select ARCH_KIRKWOOD_DT
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  Marvell (eSATA) SheevaPlug (Flattened Device Tree).
+
 config MACH_TOPKICK_DT
 	bool "USI Topkick (Flattened Device Tree)"
 	select ARCH_KIRKWOOD_DT
@@ -308,6 +316,7 @@ config MACH_TS219_DT
 	select ARCH_KIRKWOOD_DT
 	select ARM_APPENDED_DTB
 	select ARM_ATAG_DTB_COMPAT
+	select POWER_RESET_QNAP
 	help
 	  Say 'Y' here if you want your kernel to support the QNAP
 	  TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and

arch/arm/mach-kirkwood/Makefile

@@ -40,5 +40,6 @@ obj-$(CONFIG_MACH_NETSPACE_V2_DT)	+= board-ns2.o
 obj-$(CONFIG_MACH_NSA310_DT)		+= board-nsa310.o
 obj-$(CONFIG_MACH_OPENBLOCKS_A6_DT)	+= board-openblocks_a6.o
 obj-$(CONFIG_MACH_READYNAS_DT)		+= board-readynas.o
+obj-$(CONFIG_MACH_SHEEVAPLUG_DT)	+= board-sheevaplug.o
 obj-$(CONFIG_MACH_TOPKICK_DT)		+= board-usi_topkick.o
 obj-$(CONFIG_MACH_TS219_DT)		+= board-ts219.o tsx1x-common.o

arch/arm/mach-kirkwood/board-dt.c

@@ -112,6 +112,9 @@ static void __init kirkwood_dt_init(void)
 	if (of_machine_is_compatible("globalscale,guruplug"))
 		guruplug_dt_init();
 
+	if (of_machine_is_compatible("globalscale,sheevaplug"))
+		sheevaplug_dt_init();
+
 	if (of_machine_is_compatible("dlink,dns-kirkwood"))
 		dnskw_init();
 
@@ -165,6 +168,7 @@ static void __init kirkwood_dt_init(void)
 static const char * const kirkwood_dt_board_compat[] = {
 	"globalscale,dreamplug",
 	"globalscale,guruplug",
+	"globalscale,sheevaplug",
 	"dlink,dns-320",
 	"dlink,dns-325",
 	"iom,iconnect",

arch/arm/mach-kirkwood/board-lsxl.c

@@ -25,19 +25,6 @@ static struct mv643xx_eth_platform_data lsxl_ge01_data = {
 	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
 };
 
-/*
- * On the LS-XHL/LS-CHLv2, the shutdown process is following:
- * - Userland monitors key events until the power switch goes to off position
- * - The board reboots
- * - U-boot starts and goes into an idle mode waiting for the user
- *   to move the switch to ON position
- *
- */
-static void lsxl_power_off(void)
-{
-	kirkwood_restart('h', NULL);
-}
-
 void __init lsxl_init(void)
 {
 	/*
@@ -46,7 +33,4 @@ void __init lsxl_init(void)
 
 	kirkwood_ge00_init(&lsxl_ge00_data);
 	kirkwood_ge01_init(&lsxl_ge01_data);
-
-	/* register power-off method */
-	pm_power_off = lsxl_power_off;
 }

arch/arm/mach-kirkwood/board-sheevaplug.c

+/*
+ * arch/arm/mach-kirkwood/board-sheevaplug.c
+ *
+ * Marvell Sheevaplug Reference Board Init for drivers not converted to
+ * flattened device tree yet.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/mv643xx_eth.h>
+#include "common.h"
+
+static struct mv643xx_eth_platform_data sheevaplug_ge00_data = {
+	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
+};
+
+void __init sheevaplug_dt_init(void)
+{
+	/*
+	 * Basic setup. Needs to be called early.
+	 */
+	kirkwood_ge00_init(&sheevaplug_ge00_data);
+}

arch/arm/mach-kirkwood/board-ts219.c

@@ -23,7 +23,6 @@
 #include <asm/mach/arch.h>
 #include <mach/kirkwood.h>
 #include "common.h"
-#include "tsx1x-common.h"
 
 static struct mv643xx_eth_platform_data qnap_ts219_ge00_data = {
 	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
@@ -38,8 +37,6 @@ void __init qnap_dt_ts219_init(void)
 		qnap_ts219_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);
 
 	kirkwood_ge00_init(&qnap_ts219_ge00_data);
-
-	pm_power_off = qnap_tsx1x_power_off;
 }
 
 /* FIXME: Will not work with DT. Maybe use MPP40_GPIO? */

arch/arm/mach-kirkwood/common.h

@@ -65,6 +65,11 @@ void guruplug_dt_init(void);
 #else
 static inline void guruplug_dt_init(void) {};
 #endif
+#ifdef CONFIG_MACH_SHEEVAPLUG_DT
+void sheevaplug_dt_init(void);
+#else
+static inline void sheevaplug_dt_init(void) {};
+#endif
 #ifdef CONFIG_MACH_TS219_DT
 void qnap_dt_ts219_init(void);
 #else