Commit 75d9fc7f authored by Nicholas Piggin's avatar Nicholas Piggin Committed by Michael Ellerman

powerpc/powernv: move OPAL call wrapper tracing and interrupt handling to C

The OPAL call wrapper gets interrupt disabling wrong. It disables
interrupts just by clearing MSR[EE], which has two problems:

- It doesn't call into the IRQ tracing subsystem, which means tracing
  across OPAL calls does not always notice IRQs have been disabled.

- It doesn't go through the IRQ soft-mask code, which causes a minor
  bug. MSR[EE] can not be restored by saving the MSR then clearing
  MSR[EE], because a racing interrupt while soft-masked could clear
  MSR[EE] between the two steps. This can cause MSR[EE] to be
  incorrectly enabled when the OPAL call returns. Fortunately that
  should only result in another masked interrupt being taken to
  disable MSR[EE] again, but it's a bit sloppy.

The existing code also saves MSR to PACA, which is not re-entrant if
there is a nested OPAL call from different MSR contexts, which can
happen these days with SRESET interrupts on bare metal.

To fix these issues, move the tracing and IRQ handling code to C, and
call into asm just for the low level call when everything is ready to
go. Save the MSR on stack rather than PACA.

Performance cost is kept to a minimum with a few optimisations:

- The endian switch upon return is combined with the MSR restore,
  which avoids an expensive context synchronizing operation for LE
  kernels. This makes up for the additional mtmsrd to enable
  interrupts with local_irq_enable().

- blr is now used to return from the opal_* functions that are called
  as C functions, to avoid link stack corruption. This requires a
  skiboot fix as well to keep the call stack balanced.

A NULL call is more costly after this, (410ns->430ns on POWER9), but
OPAL calls are generally not performance critical at this scale.
Signed-off-by: default avatarNicholas Piggin <npiggin@gmail.com>
Signed-off-by: default avatarMichael Ellerman <mpe@ellerman.id.au>
parent 38555434
...@@ -37,13 +37,11 @@ void kexec_copy_flush(struct kimage *image); ...@@ -37,13 +37,11 @@ void kexec_copy_flush(struct kimage *image);
extern struct static_key hcall_tracepoint_key; extern struct static_key hcall_tracepoint_key;
void __trace_hcall_entry(unsigned long opcode, unsigned long *args); void __trace_hcall_entry(unsigned long opcode, unsigned long *args);
void __trace_hcall_exit(long opcode, long retval, unsigned long *retbuf); void __trace_hcall_exit(long opcode, long retval, unsigned long *retbuf);
/* OPAL tracing */
#ifdef CONFIG_JUMP_LABEL
extern struct static_key opal_tracepoint_key;
#endif
void __trace_opal_entry(unsigned long opcode, unsigned long *args); /* OPAL */
void __trace_opal_exit(long opcode, unsigned long retval); int64_t __opal_call(int64_t a0, int64_t a1, int64_t a2, int64_t a3,
int64_t a4, int64_t a5, int64_t a6, int64_t a7,
int64_t opcode, uint64_t msr);
/* VMX copying */ /* VMX copying */
int enter_vmx_usercopy(void); int enter_vmx_usercopy(void);
......
# SPDX-License-Identifier: GPL-2.0 # SPDX-License-Identifier: GPL-2.0
obj-y += setup.o opal-wrappers.o opal.o opal-async.o idle.o obj-y += setup.o opal-call.o opal-wrappers.o opal.o opal-async.o
obj-y += opal-rtc.o opal-nvram.o opal-lpc.o opal-flash.o obj-y += idle.o opal-rtc.o opal-nvram.o opal-lpc.o opal-flash.o
obj-y += rng.o opal-elog.o opal-dump.o opal-sysparam.o opal-sensor.o obj-y += rng.o opal-elog.o opal-dump.o opal-sysparam.o opal-sensor.o
obj-y += opal-msglog.o opal-hmi.o opal-power.o opal-irqchip.o obj-y += opal-msglog.o opal-hmi.o opal-power.o opal-irqchip.o
obj-y += opal-kmsg.o opal-powercap.o opal-psr.o opal-sensor-groups.o obj-y += opal-kmsg.o opal-powercap.o opal-psr.o opal-sensor-groups.o
...@@ -11,7 +11,6 @@ obj-$(CONFIG_CXL_BASE) += pci-cxl.o ...@@ -11,7 +11,6 @@ obj-$(CONFIG_CXL_BASE) += pci-cxl.o
obj-$(CONFIG_EEH) += eeh-powernv.o obj-$(CONFIG_EEH) += eeh-powernv.o
obj-$(CONFIG_PPC_SCOM) += opal-xscom.o obj-$(CONFIG_PPC_SCOM) += opal-xscom.o
obj-$(CONFIG_MEMORY_FAILURE) += opal-memory-errors.o obj-$(CONFIG_MEMORY_FAILURE) += opal-memory-errors.o
obj-$(CONFIG_TRACEPOINTS) += opal-tracepoints.o
obj-$(CONFIG_OPAL_PRD) += opal-prd.o obj-$(CONFIG_OPAL_PRD) += opal-prd.o
obj-$(CONFIG_PERF_EVENTS) += opal-imc.o obj-$(CONFIG_PERF_EVENTS) += opal-imc.o
obj-$(CONFIG_PPC_MEMTRACE) += memtrace.o obj-$(CONFIG_PPC_MEMTRACE) += memtrace.o
......
This diff is collapsed.
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment