Merge tag 'mips_5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux

Pull MIPS updates from Thomas Bogendoerfer:

 - removed get_fs/set_fs

 - removed broken/unmaintained MIPS KVM trap and emulate support

 - added support for Loongson-2K1000

 - fixes and cleanups

* tag 'mips_5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (107 commits)
  MIPS: BCM63XX: Use BUG_ON instead of condition followed by BUG.
  MIPS: select ARCH_KEEP_MEMBLOCK unconditionally
  mips: Do not include hi and lo in clobber list for R6
  MIPS:DTS:Correct the license for Loongson-2K
  MIPS:DTS:Fix label name and interrupt number of ohci for Loongson-2K
  MIPS: Avoid handcoded DIVU in `__div64_32' altogether
  lib/math/test_div64: Correct the spelling of "dividend"
  lib/math/test_div64: Fix error message formatting
  mips/bootinfo:correct some comments of fw_arg
  MIPS: Avoid DIVU in `__div64_32' is result would be zero
  MIPS: Reinstate platform `__div64_32' handler
  div64: Correct inline documentation for `do_div'
  lib/math: Add a `do_div' test module
  MIPS: Makefile: Replace -pg with CC_FLAGS_FTRACE
  MIPS: pci-legacy: revert "use generic pci_enable_resources"
  MIPS: Loongson64: Add kexec/kdump support
  MIPS: pci-legacy: use generic pci_enable_resources
  MIPS: pci-legacy: remove busn_resource field
  MIPS: pci-legacy: remove redundant info messages
  MIPS: pci-legacy: stop using of_pci_range_to_resource
  ...

Documentation/devicetree/bindings/display/panel/kingdisplay,kd035g6-54nt.yaml

@@ -47,7 +47,6 @@ examples:
 
             spi-max-frequency = <3125000>;
             spi-3wire;
-            spi-cs-high;
 
             reset-gpios = <&gpe 2 GPIO_ACTIVE_LOW>;
 

Documentation/devicetree/bindings/interrupt-controller/loongson,liointc.yaml

@@ -10,9 +10,9 @@ maintainers:
   - Jiaxun Yang <jiaxun.yang@flygoat.com>
 
 description: |
-  This interrupt controller is found in the Loongson-3 family of chips as the primary
-  package interrupt controller which can route local I/O interrupt to interrupt lines
-  of cores.
+  This interrupt controller is found in the Loongson-3 family of chips and
+  Loongson-2K1000 chip, as the primary package interrupt controller which
+  can route local I/O interrupt to interrupt lines of cores.
 
 allOf:
   - $ref: /schemas/interrupt-controller.yaml#
@@ -22,9 +22,17 @@ properties:
     oneOf:
       - const: loongson,liointc-1.0
       - const: loongson,liointc-1.0a
+      - const: loongson,liointc-2.0
 
   reg:
-    maxItems: 1
+    minItems: 1
+    maxItems: 3
+
+  reg-names:
+    items:
+      - const: main
+      - const: isr0
+      - const: isr1
 
   interrupt-controller: true
 
@@ -69,6 +77,26 @@ required:
 
 unevaluatedProperties: false
 
+if:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - loongson,liointc-2.0
+
+then:
+  properties:
+    reg:
+      minItems: 3
+
+  required:
+    - reg-names
+
+else:
+  properties:
+    reg:
+      maxItems: 1
+
 examples:
   - |
     iointc: interrupt-controller@3ff01400 {

arch/mips/Kconfig

@@ -4,13 +4,15 @@ config MIPS
 	default y
 	select ARCH_32BIT_OFF_T if !64BIT
 	select ARCH_BINFMT_ELF_STATE if MIPS_FP_SUPPORT
+	select ARCH_HAS_DEBUG_VIRTUAL if !64BIT
 	select ARCH_HAS_FORTIFY_SOURCE
 	select ARCH_HAS_KCOV
+	select ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE if !EVA
 	select ARCH_HAS_PTE_SPECIAL if !(32BIT && CPU_HAS_RIXI)
 	select ARCH_HAS_TICK_BROADCAST if GENERIC_CLOCKEVENTS_BROADCAST
 	select ARCH_HAS_UBSAN_SANITIZE_ALL
 	select ARCH_HAS_GCOV_PROFILE_ALL
-	select ARCH_KEEP_MEMBLOCK if DEBUG_KERNEL
+	select ARCH_KEEP_MEMBLOCK
 	select ARCH_SUPPORTS_UPROBES
 	select ARCH_USE_BUILTIN_BSWAP
 	select ARCH_USE_CMPXCHG_LOCKREF if 64BIT
@@ -26,6 +28,7 @@ config MIPS
 	select GENERIC_ATOMIC64 if !64BIT
 	select GENERIC_CMOS_UPDATE
 	select GENERIC_CPU_AUTOPROBE
+	select GENERIC_FIND_FIRST_BIT
 	select GENERIC_GETTIMEOFDAY
 	select GENERIC_IOMAP
 	select GENERIC_IRQ_PROBE
@@ -91,7 +94,6 @@ config MIPS
 	select PERF_USE_VMALLOC
 	select PCI_MSI_ARCH_FALLBACKS if PCI_MSI
 	select RTC_LIB
-	select SET_FS
 	select SYSCTL_EXCEPTION_TRACE
 	select VIRT_TO_BUS
 	select ARCH_HAS_ELFCORE_COMPAT
@@ -712,6 +714,7 @@ config SGI_IP27
 	select ARC_CMDLINE_ONLY
 	select BOOT_ELF64
 	select DEFAULT_SGI_PARTITION
+	select FORCE_PCI
 	select SYS_HAS_EARLY_PRINTK
 	select HAVE_PCI
 	select IRQ_MIPS_CPU
@@ -774,6 +777,7 @@ config SGI_IP30
 	select BOOT_ELF64
 	select CEVT_R4K
 	select CSRC_R4K
+	select FORCE_PCI
 	select SYNC_R4K if SMP
 	select ZONE_DMA32
 	select HAVE_PCI
@@ -998,6 +1002,7 @@ config CAVIUM_OCTEON_SOC
 	select NR_CPUS_DEFAULT_64
 	select MIPS_NR_CPU_NR_MAP_1024
 	select BUILTIN_DTB
+	select MTD
 	select MTD_COMPLEX_MAPPINGS
 	select SWIOTLB
 	select SYS_SUPPORTS_RELOCATABLE
@@ -2118,7 +2123,7 @@ config CPU_MIPS32
 config CPU_MIPS64
 	bool
 	default y if CPU_MIPS64_R1 || CPU_MIPS64_R2 || CPU_MIPS64_R5 || \
-		     CPU_MIPS64_R6
+		     CPU_MIPS64_R6 || CPU_LOONGSON64 || CPU_CAVIUM_OCTEON
 
 #
 # These indicate the revision of the architecture
@@ -2185,7 +2190,8 @@ config CPU_SUPPORTS_HUGEPAGES
 	depends on !(32BIT && (ARCH_PHYS_ADDR_T_64BIT || EVA))
 config MIPS_PGD_C0_CONTEXT
 	bool
-	default y if 64BIT && (CPU_MIPSR2 || CPU_MIPSR6) && !CPU_XLP
+	depends on 64BIT
+	default y if (CPU_MIPSR2 || CPU_MIPSR6) && !CPU_XLP
 
 #
 # Set to y for ptrace access to watch registers.
@@ -2219,23 +2225,6 @@ config 64BIT
 
 endchoice
 
-config KVM_GUEST
-	bool "KVM Guest Kernel"
-	depends on CPU_MIPS32_R2
-	depends on !64BIT && BROKEN_ON_SMP
-	help
-	  Select this option if building a guest kernel for KVM (Trap & Emulate)
-	  mode.
-
-config KVM_GUEST_TIMER_FREQ
-	int "Count/Compare Timer Frequency (MHz)"
-	depends on KVM_GUEST
-	default 100
-	help
-	  Set this to non-zero if building a guest kernel for KVM to skip RTC
-	  emulation when determining guest CPU Frequency. Instead, the guest's
-	  timer frequency is specified directly.
-
 config MIPS_VA_BITS_48
 	bool "48 bits virtual memory"
 	depends on 64BIT

arch/mips/Kconfig.debug

@@ -77,6 +77,7 @@ config CMDLINE_OVERRIDE
 config SB1XXX_CORELIS
 	bool "Corelis Debugger"
 	depends on SIBYTE_SB1xxx_SOC
+	select DEBUG_KERNEL if !COMPILE_TEST
 	select DEBUG_INFO if !COMPILE_TEST
 	help
 	  Select compile flags that produce code that can be processed by the

arch/mips/alchemy/common/clock.c

@@ -111,7 +111,7 @@ static struct clk_aliastable {
 /* access locks to SYS_FREQCTRL0/1 and SYS_CLKSRC registers */
 static spinlock_t alchemy_clk_fg0_lock;
 static spinlock_t alchemy_clk_fg1_lock;
-static spinlock_t alchemy_clk_csrc_lock;
+static DEFINE_SPINLOCK(alchemy_clk_csrc_lock);
 
 /* CPU Core clock *****************************************************/
 
@@ -996,7 +996,6 @@ static int __init alchemy_clk_setup_imux(int ctype)
 	if (!a)
 		return -ENOMEM;
 
-	spin_lock_init(&alchemy_clk_csrc_lock);
 	ret = 0;
 
 	for (i = 0; i < 6; i++) {

arch/mips/bcm63xx/clk.c

@@ -76,7 +76,7 @@ static struct clk clk_enet_misc = {
 };
 
 /*
- * Ethernet MAC clocks: only revelant on 6358, silently enable misc
+ * Ethernet MAC clocks: only relevant on 6358, silently enable misc
  * clocks
  */
 static void enetx_set(struct clk *clk, int enable)

arch/mips/bcm63xx/gpio.c

@@ -43,8 +43,7 @@ static void bcm63xx_gpio_set(struct gpio_chip *chip,
 	u32 *v;
 	unsigned long flags;
 
-	if (gpio >= chip->ngpio)
-		BUG();
+	BUG_ON(gpio >= chip->ngpio);
 
 	if (gpio < 32) {
 		reg = gpio_out_low_reg;
@@ -70,8 +69,7 @@ static int bcm63xx_gpio_get(struct gpio_chip *chip, unsigned gpio)
 	u32 reg;
 	u32 mask;
 
-	if (gpio >= chip->ngpio)
-		BUG();
+	BUG_ON(gpio >= chip->ngpio);
 
 	if (gpio < 32) {
 		reg = gpio_out_low_reg;
@@ -92,8 +90,7 @@ static int bcm63xx_gpio_set_direction(struct gpio_chip *chip,
 	u32 tmp;
 	unsigned long flags;
 
-	if (gpio >= chip->ngpio)
-		BUG();
+	BUG_ON(gpio >= chip->ngpio);
 
 	if (gpio < 32) {
 		reg = GPIO_CTL_LO_REG;

arch/mips/bmips/dma.c

@@ -10,7 +10,7 @@
 
 #include <linux/device.h>
 #include <linux/dma-direction.h>
-#include <linux/dma-mapping.h>
+#include <linux/dma-direct.h>
 #include <linux/init.h>
 #include <linux/io.h>
 #include <linux/of.h>

arch/mips/boot/compressed/Makefile

@@ -18,7 +18,7 @@ include $(srctree)/arch/mips/Kbuild.platforms
 BOOT_HEAP_SIZE := 0x400000
 
 # Disable Function Tracer
-KBUILD_CFLAGS := $(filter-out -pg, $(KBUILD_CFLAGS))
+KBUILD_CFLAGS := $(filter-out $(CC_FLAGS_FTRACE), $(KBUILD_CFLAGS))
 
 KBUILD_CFLAGS := $(filter-out -fstack-protector, $(KBUILD_CFLAGS))
 

arch/mips/boot/dts/brcm/bcm3368-netgear-cvg834g.dts

 // SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 
-/include/ "bcm3368.dtsi"
+#include "bcm3368.dtsi"
 
 / {
 	compatible = "netgear,cvg834g", "brcm,bcm3368";

arch/mips/boot/dts/brcm/bcm3368.dtsi

 // SPDX-License-Identifier: GPL-2.0
+
+#include "dt-bindings/clock/bcm3368-clock.h"
+
 / {
 	#address-cells = <1>;
 	#size-cells = <1>;
@@ -59,7 +62,7 @@ clkctl: clock-controller@fff8c004 {
 
 		periph_cntl: syscon@fff8c008 {
 			compatible = "syscon";
-			reg = <0xfff8c000 0x4>;
+			reg = <0xfff8c008 0x4>;
 			native-endian;
 		};
 

arch/mips/boot/dts/brcm/bcm63268-comtrend-vr-3032u.dts

 // SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 
-/include/ "bcm63268.dtsi"
+#include "bcm63268.dtsi"
 
 / {
 	compatible = "comtrend,vr-3032u", "brcm,bcm63268";

arch/mips/boot/dts/brcm/bcm63268.dtsi

 // SPDX-License-Identifier: GPL-2.0
+
+#include "dt-bindings/clock/bcm63268-clock.h"
+#include "dt-bindings/reset/bcm63268-reset.h"
+#include "dt-bindings/soc/bcm63268-pm.h"
+
 / {
 	#address-cells = <1>;
 	#size-cells = <1>;
@@ -24,16 +29,29 @@ cpu@1 {
 	};
 
 	clocks {
-		periph_clk: periph-clk {
+		periph_osc: periph-osc {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <50000000>;
+			clock-output-names = "periph";
+		};
+
+		hsspi_osc: hsspi-osc {
+			compatible = "fixed-clock";
+
+			#clock-cells = <0>;
+
+			clock-frequency = <400000000>;
+			clock-output-names = "hsspi_osc";
 		};
 	};
 
 	aliases {
+		nflash = &nflash;
 		serial0 = &uart0;
 		serial1 = &uart1;
+		spi0 = &lsspi;
+		spi1 = &hsspi;
 	};
 
 	cpu_intc: interrupt-controller {
@@ -51,23 +69,22 @@ ubus {
 		compatible = "simple-bus";
 		ranges;
 
-		clkctl: clock-controller@10000004 {
+		periph_clk: clock-controller@10000004 {
 			compatible = "brcm,bcm63268-clocks";
 			reg = <0x10000004 0x4>;
 			#clock-cells = <1>;
 		};
 
-		periph_cntl: syscon@10000008 {
+		pll_cntl: syscon@10000008 {
 			compatible = "syscon";
-			reg = <0x10000000 0xc>;
+			reg = <0x10000008 0x4>;
 			native-endian;
-		};
 
-		reboot: syscon-reboot@10000008 {
-			compatible = "syscon-reboot";
-			regmap = <&periph_cntl>;
-			offset = <0x0>;
-			mask = <0x1>;
+			reboot {
+				compatible = "syscon-reboot";
+				offset = <0x0>;
+				mask = <0x1>;
+			};
 		};
 
 		periph_rst: reset-controller@10000010 {
@@ -88,6 +105,16 @@ periph_intc: interrupt-controller@10000020 {
 			interrupts = <2>, <3>;
 		};
 
+		wdt: watchdog@1000009c {
+			compatible = "brcm,bcm7038-wdt";
+			reg = <0x1000009c 0xc>;
+
+			clocks = <&periph_osc>;
+			clock-names = "refclk";
+
+			timeout-sec = <30>;
+		};
+
 		uart0: serial@10000180 {
 			compatible = "brcm,bcm6345-uart";
 			reg = <0x10000180 0x18>;
@@ -95,12 +122,34 @@ uart0: serial@10000180 {
 			interrupt-parent = <&periph_intc>;
 			interrupts = <5>;
 
-			clocks = <&periph_clk>;
+			clocks = <&periph_osc>;
 			clock-names = "refclk";
 
 			status = "disabled";
 		};
 
+		nflash: nand@10000200 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,nand-bcm6368",
+				     "brcm,brcmnand-v4.0",
+				     "brcm,brcmnand";
+			reg = <0x10000200 0x180>,
+			      <0x10000600 0x200>,
+			      <0x100000b0 0x10>;
+			reg-names = "nand",
+				    "nand-cache",
+				    "nand-int-base";
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <50>;
+
+			clocks = <&periph_clk BCM63268_CLK_NAND>;
+			clock-names = "nand";
+
+			status = "disabled";
+		};
+
 		uart1: serial@100001a0 {
 			compatible = "brcm,bcm6345-uart";
 			reg = <0x100001a0 0x18>;
@@ -108,17 +157,44 @@ uart1: serial@100001a0 {
 			interrupt-parent = <&periph_intc>;
 			interrupts = <34>;
 
-			clocks = <&periph_clk>;
+			clocks = <&periph_osc>;
 			clock-names = "refclk";
 
 			status = "disabled";
 		};
 
-		leds0: led-controller@10001900 {
+		lsspi: spi@10000800 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "brcm,bcm6328-leds";
-			reg = <0x10001900 0x24>;
+			compatible = "brcm,bcm6358-spi";
+			reg = <0x10000800 0x70c>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <80>;
+
+			clocks = <&periph_clk BCM63268_CLK_SPI>;
+			clock-names = "spi";
+
+			resets = <&periph_rst BCM63268_RST_SPI>;
+
+			status = "disabled";
+		};
+
+		hsspi: spi@10001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6328-hsspi";
+			reg = <0x10001000 0x600>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <6>;
+
+			clocks = <&periph_clk BCM63268_CLK_HSSPI>,
+				 <&hsspi_osc>;
+			clock-names = "hsspi",
+				      "pll";
+
+			resets = <&periph_rst BCM63268_RST_SPI>;
 
 			status = "disabled";
 		};
@@ -129,6 +205,15 @@ periph_pwr: power-controller@1000184c {
 			#power-domain-cells = <1>;
 		};
 
+		leds0: led-controller@10001900 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6328-leds";
+			reg = <0x10001900 0x24>;
+
+			status = "disabled";
+		};
+
 		ehci: usb@10002500 {
 			compatible = "brcm,bcm63268-ehci", "generic-ehci";
 			reg = <0x10002500 0x100>;
@@ -137,6 +222,9 @@ ehci: usb@10002500 {
 			interrupt-parent = <&periph_intc>;
 			interrupts = <10>;
 
+			phys = <&usbh 0>;
+			phy-names = "usb";
+
 			status = "disabled";
 		};
 
@@ -149,6 +237,25 @@ ohci: usb@10002600 {
 			interrupt-parent = <&periph_intc>;
 			interrupts = <9>;
 
+			phys = <&usbh 0>;
+			phy-names = "usb";
+
+			status = "disabled";
+		};
+
+		usbh: usb-phy@10002700 {
+			compatible = "brcm,bcm63268-usbh-phy";
+			reg = <0x10002700 0x38>;
+			#phy-cells = <1>;
+
+			clocks = <&periph_clk BCM63268_CLK_USBH>;
+			clock-names = "usbh";
+
+			power-domains = <&periph_pwr BCM63268_POWER_DOMAIN_USBH>;
+
+			resets = <&periph_rst BCM63268_RST_USBH>;
+			reset-names = "usbh";
+
 			status = "disabled";
 		};
 	};

arch/mips/boot/dts/brcm/bcm6328.dtsi

 // SPDX-License-Identifier: GPL-2.0
+
+#include "dt-bindings/clock/bcm6328-clock.h"
+#include "dt-bindings/reset/bcm6328-reset.h"
+#include "dt-bindings/soc/bcm6328-pm.h"
+
 / {
 	#address-cells = <1>;
 	#size-cells = <1>;
@@ -24,16 +29,26 @@ cpu@1 {
 	};
 
 	clocks {
-		periph_clk: periph-clk {
+		periph_osc: periph-osc {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <50000000>;
+			clock-output-names = "periph";
+		};
+
+		hsspi_osc: hsspi-osc {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <133333333>;
+			clock-output-names = "hsspi_osc";
 		};
 	};
 
 	aliases {
+		nflash = &nflash;
 		serial0 = &uart0;
 		serial1 = &uart1;
+		spi1 = &hsspi;
 	};
 
 	cpu_intc: interrupt-controller {
@@ -51,7 +66,7 @@ ubus {
 		compatible = "simple-bus";
 		ranges;
 
-		clkctl: clock-controller@10000004 {
+		periph_clk: clock-controller@10000004 {
 			compatible = "brcm,bcm6328-clocks";
 			reg = <0x10000004 0x4>;
 			#clock-cells = <1>;
@@ -75,37 +90,71 @@ periph_intc: interrupt-controller@10000020 {
 			interrupts = <2>, <3>;
 		};
 
+		wdt: watchdog@1000005c {
+			compatible = "brcm,bcm7038-wdt";
+			reg = <0x1000005c 0xc>;
+
+			clocks = <&periph_osc>;
+			clock-names = "refclk";
+
+			timeout-sec = <30>;
+		};
+
+		soft_reset: syscon@10000068 {
+			compatible = "syscon";
+			reg = <0x10000068 0x4>;
+			native-endian;
+
+			reboot {
+				compatible = "syscon-reboot";
+				offset = <0x0>;
+				mask = <0x1>;
+			};
+		};
+
 		uart0: serial@10000100 {
 			compatible = "brcm,bcm6345-uart";
 			reg = <0x10000100 0x18>;
+
 			interrupt-parent = <&periph_intc>;
 			interrupts = <28>;
-			clocks = <&periph_clk>;
+
+			clocks = <&periph_osc>;
 			clock-names = "refclk";
+
 			status = "disabled";
 		};
 
 		uart1: serial@10000120 {
 			compatible = "brcm,bcm6345-uart";
 			reg = <0x10000120 0x18>;
+
 			interrupt-parent = <&periph_intc>;
 			interrupts = <39>;
-			clocks = <&periph_clk>;
+
+			clocks = <&periph_osc>;
 			clock-names = "refclk";
+
 			status = "disabled";
 		};
 
-		timer: syscon@10000040 {
-			compatible = "syscon";
-			reg = <0x10000040 0x2c>;
-			native-endian;
-		};
+		nflash: nand@10000200 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,nand-bcm6368",
+				     "brcm,brcmnand-v2.2",
+				     "brcm,brcmnand";
+			reg = <0x10000200 0x180>,
+			      <0x10000400 0x200>,
+			      <0x10000070 0x10>;
+			reg-names = "nand",
+				    "nand-cache",
+				    "nand-int-base";
 
-		reboot: syscon-reboot@10000068 {
-			compatible = "syscon-reboot";
-			regmap = <&timer>;
-			offset = <0x28>;
-			mask = <0x1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <0>;
+
+			status = "disabled";
 		};
 
 		leds0: led-controller@10000800 {
@@ -113,6 +162,27 @@ leds0: led-controller@10000800 {
 			#size-cells = <0>;
 			compatible = "brcm,bcm6328-leds";
 			reg = <0x10000800 0x24>;
+
+			status = "disabled";
+		};
+
+		hsspi: spi@10001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6328-hsspi";
+			reg = <0x10001000 0x600>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <29>;
+
+			clocks = <&periph_clk BCM6328_CLK_HSSPI>,
+				 <&hsspi_osc>;
+			clock-names = "hsspi",
+				      "pll";
+
+			resets = <&periph_rst BCM6328_RST_SPI>;
+			reset-names = "hsspi";
+
 			status = "disabled";
 		};
 
@@ -126,8 +196,13 @@ ehci: usb@10002500 {
 			compatible = "brcm,bcm6328-ehci", "generic-ehci";
 			reg = <0x10002500 0x100>;
 			big-endian;
+
 			interrupt-parent = <&periph_intc>;
 			interrupts = <42>;
+
+			phys = <&usbh 0>;
+			phy-names = "usb";
+
 			status = "disabled";
 		};
 
@@ -136,8 +211,29 @@ ohci: usb@10002600 {
 			reg = <0x10002600 0x100>;
 			big-endian;
 			no-big-frame-no;
+
 			interrupt-parent = <&periph_intc>;
 			interrupts = <41>;
+
+			phys = <&usbh 0>;
+			phy-names = "usb";
+
+			status = "disabled";
+		};
+
+		usbh: usb-phy@10002700 {
+			compatible = "brcm,bcm6328-usbh-phy";
+			reg = <0x10002700 0x38>;
+			#phy-cells = <1>;
+
+			clocks = <&periph_clk BCM6328_CLK_USBH>;
+			clock-names = "usbh";
+
+			power-domains = <&periph_pwr BCM6328_POWER_DOMAIN_USBH>;
+
+			resets = <&periph_rst BCM6328_RST_USBH>;
+			reset-names = "usbh";
+
 			status = "disabled";
 		};
 	};

arch/mips/boot/dts/brcm/bcm6358-neufbox4-sercomm.dts

 // SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 
-/include/ "bcm6358.dtsi"
+#include "bcm6358.dtsi"
 
 / {
 	compatible = "sfr,nb4-ser", "brcm,bcm6358";

arch/mips/boot/dts/brcm/bcm6358.dtsi

 // SPDX-License-Identifier: GPL-2.0
+
+#include "dt-bindings/clock/bcm6358-clock.h"
+#include "dt-bindings/reset/bcm6358-reset.h"
+
 / {
 	#address-cells = <1>;
 	#size-cells = <1>;
@@ -24,16 +28,19 @@ cpu@1 {
 	};
 
 	clocks {
-		periph_clk: periph-clk {
+		periph_osc: periph-osc {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <50000000>;
+			clock-output-names = "periph";
 		};
 	};
 
 	aliases {
+		pflash = &pflash;
 		serial0 = &uart0;
 		serial1 = &uart1;
+		spi0 = &lsspi;
 	};
 
 	cpu_intc: interrupt-controller {
@@ -51,23 +58,22 @@ ubus {
 		compatible = "simple-bus";
 		ranges;
 
-		clkctl: clock-controller@fffe0004 {
+		periph_clk: clock-controller@fffe0004 {
 			compatible = "brcm,bcm6358-clocks";
 			reg = <0xfffe0004 0x4>;
 			#clock-cells = <1>;
 		};
 
-		periph_cntl: syscon@fffe0008 {
+		pll_cntl: syscon@fffe0008 {
 			compatible = "syscon";
-			reg = <0xfffe0000 0x4>;
+			reg = <0xfffe0008 0x4>;
 			native-endian;
-		};
 
-		reboot: syscon-reboot@fffe0008 {
-			compatible = "syscon-reboot";
-			regmap = <&periph_cntl>;
-			offset = <0x0>;
-			mask = <0x1>;
+			reboot {
+				compatible = "syscon-reboot";
+				offset = <0x0>;
+				mask = <0x1>;
+			};
 		};
 
 		periph_intc: interrupt-controller@fffe000c {
@@ -88,6 +94,16 @@ periph_rst: reset-controller@fffe0034 {
 			#reset-cells = <1>;
 		};
 
+		wdt: watchdog@fffe005c {
+			compatible = "brcm,bcm7038-wdt";
+			reg = <0xfffe005c 0xc>;
+
+			clocks = <&periph_osc>;
+			clock-names = "refclk";
+
+			timeout-sec = <30>;
+		};
+
 		leds0: led-controller@fffe00d0 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -104,7 +120,7 @@ uart0: serial@fffe0100 {
 			interrupt-parent = <&periph_intc>;
 			interrupts = <2>;
 
-			clocks = <&periph_clk>;
+			clocks = <&periph_osc>;
 			clock-names = "refclk";
 
 			status = "disabled";
@@ -117,18 +133,41 @@ uart1: serial@fffe0120 {
 			interrupt-parent = <&periph_intc>;
 			interrupts = <3>;
 
-			clocks = <&periph_clk>;
+			clocks = <&periph_osc>;
 			clock-names = "refclk";
 
 			status = "disabled";
 		};
 
+		lsspi: spi@fffe0800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6358-spi";
+			reg = <0xfffe0800 0x70c>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <1>;
+
+			clocks = <&periph_clk BCM6358_CLK_SPI>;
+			clock-names = "spi";
+
+			resets = <&periph_rst BCM6358_RST_SPI>;
+			reset-names = "spi";
+
+			status = "disabled";
+		};
+
 		ehci: usb@fffe1300 {
 			compatible = "brcm,bcm6358-ehci", "generic-ehci";
 			reg = <0xfffe1300 0x100>;
 			big-endian;
+
 			interrupt-parent = <&periph_intc>;
 			interrupts = <10>;
+
+			phys = <&usbh 0>;
+			phy-names = "usb";
+
 			status = "disabled";
 		};
 
@@ -137,9 +176,35 @@ ohci: usb@fffe1400 {
 			reg = <0xfffe1400 0x100>;
 			big-endian;
 			no-big-frame-no;
+
 			interrupt-parent = <&periph_intc>;
 			interrupts = <5>;
+
+			phys = <&usbh 0>;
+			phy-names = "usb";
+
 			status = "disabled";
 		};
+
+		usbh: usb-phy@fffe1500 {
+			compatible = "brcm,bcm6358-usbh-phy";
+			reg = <0xfffe1500 0x38>;
+			#phy-cells = <1>;
+
+			resets = <&periph_rst BCM6358_RST_USBH>;
+			reset-names = "usbh";
+
+			status = "disabled";
+		};
+	};
+
+	pflash: nor@1e000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "cfi-flash";
+		reg = <0x1e000000 0x2000000>;
+		bank-width = <2>;
+
+		status = "disabled";
 	};
 };

arch/mips/boot/dts/brcm/bcm6362-neufbox6-sercomm.dts

 // SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 
-/include/ "bcm6362.dtsi"
+#include "bcm6362.dtsi"
 
 / {
 	compatible = "sfr,nb6-ser", "brcm,bcm6362";

arch/mips/boot/dts/brcm/bcm6362.dtsi

 // SPDX-License-Identifier: GPL-2.0
+
+#include "dt-bindings/clock/bcm6362-clock.h"
+#include "dt-bindings/reset/bcm6362-reset.h"
+#include "dt-bindings/soc/bcm6362-pm.h"
+
 / {
 	#address-cells = <1>;
 	#size-cells = <1>;
@@ -24,16 +29,29 @@ cpu@1 {
 	};
 
 	clocks {
-		periph_clk: periph-clk {
+		periph_osc: periph-osc {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <50000000>;
+			clock-output-names = "periph";
+		};
+
+		hsspi_osc: hsspi-osc {
+			compatible = "fixed-clock";
+
+			#clock-cells = <0>;
+
+			clock-frequency = <400000000>;
+			clock-output-names = "hsspi_osc";
 		};
 	};
 
 	aliases {
+		nflash = &nflash;
 		serial0 = &uart0;
 		serial1 = &uart1;
+		spi0 = &lsspi;
+		spi1 = &hsspi;
 	};
 
 	cpu_intc: interrupt-controller {
@@ -51,23 +69,22 @@ ubus {
 		compatible = "simple-bus";
 		ranges;
 
-		clkctl: clock-controller@10000004 {
+		periph_clk: clock-controller@10000004 {
 			compatible = "brcm,bcm6362-clocks";
 			reg = <0x10000004 0x4>;
 			#clock-cells = <1>;
 		};
 
-		periph_cntl: syscon@10000008 {
+		pll_cntl: syscon@10000008 {
 			compatible = "syscon";
-			reg = <0x10000000 0xc>;
+			reg = <0x10000008 0x4>;
 			native-endian;
-		};
 
-		reboot: syscon-reboot@10000008 {
-			compatible = "syscon-reboot";
-			regmap = <&periph_cntl>;
-			offset = <0x0>;
-			mask = <0x1>;
+			reboot {
+				compatible = "syscon-reboot";
+				offset = <0x0>;
+				mask = <0x1>;
+			};
 		};
 
 		periph_rst: reset-controller@10000010 {
@@ -88,6 +105,16 @@ periph_intc: interrupt-controller@10000020 {
 			interrupts = <2>, <3>;
 		};
 
+		wdt: watchdog@1000005c {
+			compatible = "brcm,bcm7038-wdt";
+			reg = <0x1000005c 0xc>;
+
+			clocks = <&periph_osc>;
+			clock-names = "refclk";
+
+			timeout-sec = <30>;
+		};
+
 		uart0: serial@10000100 {
 			compatible = "brcm,bcm6345-uart";
 			reg = <0x10000100 0x18>;
@@ -95,7 +122,7 @@ uart0: serial@10000100 {
 			interrupt-parent = <&periph_intc>;
 			interrupts = <3>;
 
-			clocks = <&periph_clk>;
+			clocks = <&periph_osc>;
 			clock-names = "refclk";
 
 			status = "disabled";
@@ -108,12 +135,72 @@ uart1: serial@10000120 {
 			interrupt-parent = <&periph_intc>;
 			interrupts = <4>;
 
-			clocks = <&periph_clk>;
+			clocks = <&periph_osc>;
 			clock-names = "refclk";
 
 			status = "disabled";
 		};
 
+		nflash: nand@10000200 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,nand-bcm6368",
+				     "brcm,brcmnand-v2.2",
+				     "brcm,brcmnand";
+			reg = <0x10000200 0x180>,
+			      <0x10000600 0x200>,
+			      <0x10000070 0x10>;
+			reg-names = "nand",
+				    "nand-cache",
+				    "nand-int-base";
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <12>;
+
+			clocks = <&periph_clk BCM6362_CLK_NAND>;
+			clock-names = "nand";
+
+			status = "disabled";
+		};
+
+		lsspi: spi@10000800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6358-spi";
+			reg = <0x10000800 0x70c>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <2>;
+
+			clocks = <&periph_clk BCM6362_CLK_SPI>;
+			clock-names = "spi";
+
+			resets = <&periph_rst BCM6362_RST_SPI>;
+			reset-names = "spi";
+
+			status = "disabled";
+		};
+
+		hsspi: spi@10001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6328-hsspi";
+			reg = <0x10001000 0x600>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <5>;
+
+			clocks = <&periph_clk BCM6362_CLK_HSSPI>,
+				 <&hsspi_osc>;
+			clock-names = "hsspi",
+				      "pll";
+
+			resets = <&periph_rst BCM6362_RST_SPI>;
+			reset-names = "hsspi";
+
+			status = "disabled";
+		};
+
 		periph_pwr: power-controller@10001848 {
 			compatible = "brcm,bcm6362-power-controller";
 			reg = <0x10001848 0x4>;
@@ -137,6 +224,9 @@ ehci: usb@10002500 {
 			interrupt-parent = <&periph_intc>;
 			interrupts = <10>;
 
+			phys = <&usbh 0>;
+			phy-names = "usb";
+
 			status = "disabled";
 		};
 
@@ -149,6 +239,26 @@ ohci: usb@10002600 {
 			interrupt-parent = <&periph_intc>;
 			interrupts = <9>;
 
+			phys = <&usbh 0>;
+			phy-names = "usb";
+
+			status = "disabled";
+		};
+
+		usbh: usb-phy@10002700 {
+			compatible = "brcm,bcm6362-usbh-phy";
+			reg = <0x10002700 0x38>;
+
+			#phy-cells = <1>;
+
+			clocks = <&periph_clk BCM6362_CLK_USBH>;
+			clock-names = "usbh";
+
+			power-domains = <&periph_pwr BCM6362_POWER_DOMAIN_USBH>;
+
+			resets = <&periph_rst BCM6362_RST_USBH>;
+			reset-names = "usbh";
+
 			status = "disabled";
 		};
 	};

arch/mips/boot/dts/brcm/bcm6368.dtsi

 // SPDX-License-Identifier: GPL-2.0
+
+#include "dt-bindings/clock/bcm6368-clock.h"
+#include "dt-bindings/reset/bcm6368-reset.h"
+
 / {
 	#address-cells = <1>;
 	#size-cells = <1>;
@@ -24,16 +28,20 @@ cpu@1 {
 	};
 
 	clocks {
-		periph_clk: periph-clk {
+		periph_osc: periph-osc {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <50000000>;
+			clock-output-names = "periph";
 		};
 	};
 
 	aliases {
+		nflash = &nflash;
+		pflash = &pflash;
 		serial0 = &uart0;
 		serial1 = &uart1;
+		spi0 = &lsspi;
 	};
 
 	cpu_intc: interrupt-controller {
@@ -51,23 +59,22 @@ ubus {
 		compatible = "simple-bus";
 		ranges;
 
-		clkctl: clock-controller@10000004 {
+		periph_clk: clock-controller@10000004 {
 			compatible = "brcm,bcm6368-clocks";
 			reg = <0x10000004 0x4>;
 			#clock-cells = <1>;
 		};
 
-		periph_cntl: syscon@100000008 {
+		pll_cntl: syscon@100000008 {
 			compatible = "syscon";
-			reg = <0x10000000 0xc>;
+			reg = <0x10000008 0x4>;
 			native-endian;
-		};
 
-		reboot: syscon-reboot@10000008 {
-			compatible = "syscon-reboot";
-			regmap = <&periph_cntl>;
-			offset = <0x0>;
-			mask = <0x1>;
+			reboot {
+				compatible = "syscon-reboot";
+				offset = <0x0>;
+				mask = <0x1>;
+			};
 		};
 
 		periph_rst: reset-controller@10000010 {
@@ -88,31 +95,88 @@ periph_intc: interrupt-controller@10000020 {
 			interrupts = <2>, <3>;
 		};
 
+		wdt: watchdog@1000005c {
+			compatible = "brcm,bcm7038-wdt";
+			reg = <0x1000005c 0xc>;
+
+			clocks = <&periph_osc>;
+			clock-names = "refclk";
+
+			timeout-sec = <30>;
+		};
+
 		leds0: led-controller@100000d0 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "brcm,bcm6358-leds";
 			reg = <0x100000d0 0x8>;
+
 			status = "disabled";
 		};
 
 		uart0: serial@10000100 {
 			compatible = "brcm,bcm6345-uart";
 			reg = <0x10000100 0x18>;
+
 			interrupt-parent = <&periph_intc>;
 			interrupts = <2>;
-			clocks = <&periph_clk>;
+
+			clocks = <&periph_osc>;
 			clock-names = "refclk";
+
 			status = "disabled";
 		};
 
 		uart1: serial@10000120 {
 			compatible = "brcm,bcm6345-uart";
 			reg = <0x10000120 0x18>;
+
 			interrupt-parent = <&periph_intc>;
 			interrupts = <3>;
-			clocks = <&periph_clk>;
+
+			clocks = <&periph_osc>;
 			clock-names = "refclk";
+
+			status = "disabled";
+		};
+
+		nflash: nand@10000200 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,nand-bcm6368",
+				     "brcm,brcmnand-v2.1",
+				     "brcm,brcmnand";
+			reg = <0x10000200 0x180>,
+			      <0x10000600 0x200>,
+			      <0x10000070 0x10>;
+			reg-names = "nand",
+				    "nand-cache",
+				    "nand-int-base";
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <10>;
+
+			clocks = <&periph_clk BCM6368_CLK_NAND>;
+			clock-names = "nand";
+
+			status = "disabled";
+		};
+
+		lsspi: spi@10000800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6358-spi";
+			reg = <0x10000800 0x70c>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <1>;
+
+			clocks = <&periph_clk BCM6368_CLK_SPI>;
+			clock-names = "spi";
+
+			resets = <&periph_rst BCM6368_RST_SPI>;
+			reset-names = "spi";
+
 			status = "disabled";
 		};
 
@@ -120,8 +184,13 @@ ehci: usb@10001500 {
 			compatible = "brcm,bcm6368-ehci", "generic-ehci";
 			reg = <0x10001500 0x100>;
 			big-endian;
+
 			interrupt-parent = <&periph_intc>;
 			interrupts = <7>;
+
+			phys = <&usbh 0>;
+			phy-names = "usb";
+
 			status = "disabled";
 		};
 
@@ -130,9 +199,49 @@ ohci: usb@10001600 {
 			reg = <0x10001600 0x100>;
 			big-endian;
 			no-big-frame-no;
+
 			interrupt-parent = <&periph_intc>;
 			interrupts = <5>;
+
+			phys = <&usbh 0>;
+			phy-names = "usb";
+
 			status = "disabled";
 		};
+
+		usbh: usb-phy@10001700 {
+			compatible = "brcm,bcm6368-usbh-phy";
+			reg = <0x10001700 0x38>;
+			#phy-cells = <1>;
+
+			clocks = <&periph_clk BCM6368_CLK_USBH>;
+			clock-names = "usbh";
+
+			resets = <&periph_rst BCM6368_RST_USBH>;
+			reset-names = "usbh";
+
+			status = "disabled";
+		};
+
+		random: rng@10004180 {
+			compatible = "brcm,bcm6368-rng";
+			reg = <0x10004180 0x14>;
+
+			clocks = <&periph_clk BCM6368_CLK_IPSEC>;
+			clock-names = "ipsec";
+
+			resets = <&periph_rst BCM6368_RST_IPSEC>;
+			reset-names = "ipsec";
+		};
+	};
+
+	pflash: nor@18000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "cfi-flash";
+		reg = <0x18000000 0x2000000>;
+		bank-width = <2>;
+
+		status = "disabled";
 	};
 };

arch/mips/boot/dts/brcm/bcm93384wvg.dts

 // SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 
-/include/ "bcm3384_zephyr.dtsi"
+#include "bcm3384_zephyr.dtsi"
 
 / {
 	compatible = "brcm,bcm93384wvg", "brcm,bcm3384";

arch/mips/boot/dts/brcm/bcm93384wvg_viper.dts

 // SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 
-/include/ "bcm3384_viper.dtsi"
+#include "bcm3384_viper.dtsi"
 
 / {
 	compatible = "brcm,bcm93384wvg-viper", "brcm,bcm3384-viper";

arch/mips/boot/dts/brcm/bcm96368mvwg.dts

 // SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 
-/include/ "bcm6368.dtsi"
+#include "bcm6368.dtsi"
 
 / {
 	compatible = "brcm,bcm96368mvwg", "brcm,bcm6368";

arch/mips/boot/dts/brcm/bcm97125cbmb.dts

 // SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 
-/include/ "bcm7125.dtsi"
+#include "bcm7125.dtsi"
 
 / {
 	compatible = "brcm,bcm97125cbmb", "brcm,bcm7125";

arch/mips/boot/dts/brcm/bcm97346dbsmb.dts

 // SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 
-/include/ "bcm7346.dtsi"
-/include/ "bcm97xxx-nand-cs1-bch24.dtsi"
+#include "bcm7346.dtsi"
+#include "bcm97xxx-nand-cs1-bch24.dtsi"
 
 / {
 	compatible = "brcm,bcm97346dbsmb", "brcm,bcm7346";

arch/mips/boot/dts/brcm/bcm97358svmb.dts

 // SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 
-/include/ "bcm7358.dtsi"
-/include/ "bcm97xxx-nand-cs1-bch4.dtsi"
+#include "bcm7358.dtsi"
+#include "bcm97xxx-nand-cs1-bch4.dtsi"
 
 / {
 	compatible = "brcm,bcm97358svmb", "brcm,bcm7358";

arch/mips/boot/dts/brcm/bcm97360svmb.dts

 // SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 
-/include/ "bcm7360.dtsi"
+#include "bcm7360.dtsi"
 
 / {
 	compatible = "brcm,bcm97360svmb", "brcm,bcm7360";

arch/mips/boot/dts/brcm/bcm97362svmb.dts

 // SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 
-/include/ "bcm7362.dtsi"
-/include/ "bcm97xxx-nand-cs1-bch4.dtsi"
+#include "bcm7362.dtsi"
+#include "bcm97xxx-nand-cs1-bch4.dtsi"
 
 / {
 	compatible = "brcm,bcm97362svmb", "brcm,bcm7362";

arch/mips/boot/dts/brcm/bcm97420c.dts

 // SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 
-/include/ "bcm7420.dtsi"
+#include "bcm7420.dtsi"
 
 / {
 	compatible = "brcm,bcm97420c", "brcm,bcm7420";

arch/mips/boot/dts/brcm/bcm97425svmb.dts

 // SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 
-/include/ "bcm7425.dtsi"
-/include/ "bcm97xxx-nand-cs1-bch24.dtsi"
+#include "bcm7425.dtsi"
+#include "bcm97xxx-nand-cs1-bch24.dtsi"
 
 / {
 	compatible = "brcm,bcm97425svmb", "brcm,bcm7425";

arch/mips/boot/dts/brcm/bcm97435svmb.dts

 // SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 
-/include/ "bcm7435.dtsi"
-/include/ "bcm97xxx-nand-cs1-bch24.dtsi"
+#include "bcm7435.dtsi"
+#include "bcm97xxx-nand-cs1-bch24.dtsi"
 
 / {
 	compatible = "brcm,bcm97435svmb", "brcm,bcm7435";

arch/mips/boot/dts/brcm/bcm9ejtagprb.dts

 // SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 
-/include/ "bcm6328.dtsi"
+#include "bcm6328.dtsi"
 
 / {
 	compatible = "brcm,bcm9ejtagprb", "brcm,bcm6328";

arch/mips/boot/dts/ingenic/gcw0.dts

@@ -345,7 +345,6 @@ nt39016@0 {
 
 			spi-max-frequency = <3125000>;
 			spi-3wire;
-			spi-cs-high;
 
 			reset-gpios = <&gpe 2 GPIO_ACTIVE_LOW>;
 

arch/mips/boot/dts/loongson/Makefile

 # SPDX_License_Identifier: GPL_2.0
+dtb-$(CONFIG_MACH_LOONGSON64)	+= loongson64_2core_2k1000.dtb
 dtb-$(CONFIG_MACH_LOONGSON64)	+= loongson64c_4core_ls7a.dtb
 dtb-$(CONFIG_MACH_LOONGSON64)	+= loongson64c_4core_rs780e.dtb
 dtb-$(CONFIG_MACH_LOONGSON64)	+= loongson64c_8core_rs780e.dtb

arch/mips/boot/dts/loongson/loongson64-2k1000.dtsi

+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "loongson,loongson2k1000";
+
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "loongson,gs264";
+			reg = <0x0>;
+			#clock-cells = <1>;
+			clocks = <&cpu_clk>;
+		};
+	};
+
+	memory {
+		compatible = "memory";
+		device_type = "memory";
+		reg = <0x00000000 0x00200000 0x00000000 0x0ee00000>, /* 238 MB at 2 MB */
+			<0x00000000 0x20000000 0x00000000 0x1f000000>, /* 496 MB at 512 MB */
+			<0x00000001 0x10000000 0x00000001 0xb0000000>; /* 6912 MB at 4352MB */
+	};
+
+	cpu_clk: cpu_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <800000000>;
+	};
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	package0: bus@10000000 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0 0x10000000 0 0x10000000 0 0x10000000 /* ioports */
+			0 0x40000000 0 0x40000000 0 0x40000000
+			0xfe 0x00000000 0xfe 0x00000000 0 0x40000000>;
+
+		liointc0: interrupt-controller@1fe11400 {
+			compatible = "loongson,liointc-2.0";
+			reg = <0 0x1fe11400 0 0x40>,
+				<0 0x1fe11040 0 0x8>,
+				<0 0x1fe11140 0 0x8>;
+			reg-names = "main", "isr0", "isr1";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&cpuintc>;
+			interrupts = <2>;
+			interrupt-names = "int0";
+
+			loongson,parent_int_map = <0xffffffff>, /* int0 */
+						<0x00000000>, /* int1 */
+						<0x00000000>, /* int2 */
+						<0x00000000>; /* int3 */
+		};
+
+		liointc1: interrupt-controller@1fe11440 {
+			compatible = "loongson,liointc-2.0";
+			reg = <0 0x1fe11440 0 0x40>,
+				<0 0x1fe11048 0 0x8>,
+				<0 0x1fe11148 0 0x8>;
+			reg-names = "main", "isr0", "isr1";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&cpuintc>;
+			interrupts = <3>;
+			interrupt-names = "int1";
+
+			loongson,parent_int_map = <0x00000000>, /* int0 */
+						<0xffffffff>, /* int1 */
+						<0x00000000>, /* int2 */
+						<0x00000000>; /* int3 */
+		};
+
+		uart0: serial@1fe00000 {
+			compatible = "ns16550a";
+			reg = <0 0x1fe00000 0 0x8>;
+			clock-frequency = <125000000>;
+			interrupt-parent = <&liointc0>;
+			interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+			no-loopback-test;
+		};
+
+		pci@1a000000 {
+			compatible = "loongson,ls2k-pci";
+			device_type = "pci";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <2>;
+
+			reg = <0 0x1a000000 0 0x02000000>,
+				<0xfe 0x00000000 0 0x20000000>;
+
+			ranges = <0x01000000 0x0 0x00000000 0x0 0x18000000  0x0 0x00010000>,
+				 <0x02000000 0x0 0x40000000 0x0 0x40000000  0x0 0x40000000>;
+
+			ehci@4,1 {
+				compatible = "pci0014,7a14.0",
+						   "pci0014,7a14",
+						   "pciclass0c0320",
+						   "pciclass0c03";
+
+				reg = <0x2100 0x0 0x0 0x0 0x0>;
+				interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-parent = <&liointc1>;
+			};
+
+			ohci@4,2 {
+				compatible = "pci0014,7a24.0",
+						   "pci0014,7a24",
+						   "pciclass0c0310",
+						   "pciclass0c03";
+
+				reg = <0x2200 0x0 0x0 0x0 0x0>;
+				interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-parent = <&liointc1>;
+			};
+
+			sata@8,0 {
+				compatible = "pci0014,7a08.0",
+						   "pci0014,7a08",
+						   "pciclass010601",
+						   "pciclass0106";
+
+				reg = <0x4000 0x0 0x0 0x0 0x0>;
+				interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-parent = <&liointc0>;
+			};
+
+			pci_bridge@9,0 {
+				compatible = "pci0014,7a19.0",
+						   "pci0014,7a19",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x4800 0x0 0x0 0x0 0x0>;
+				#interrupt-cells = <1>;
+				interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-parent = <&liointc1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &liointc1 0 IRQ_TYPE_LEVEL_LOW>;
+				external-facing;
+			};
+
+			pci_bridge@a,0 {
+				compatible = "pci0014,7a19.0",
+						   "pci0014,7a19",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x5000 0x0 0x0 0x0 0x0>;
+				#interrupt-cells = <1>;
+				interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-parent = <&liointc1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &liointc1 1 IRQ_TYPE_LEVEL_LOW>;
+				external-facing;
+			};
+
+			pci_bridge@b,0 {
+				compatible = "pci0014,7a19.0",
+						   "pci0014,7a19",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x5800 0x0 0x0 0x0 0x0>;
+				#interrupt-cells = <1>;
+				interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-parent = <&liointc1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &liointc1 2 IRQ_TYPE_LEVEL_LOW>;
+				external-facing;
+			};
+
+			pci_bridge@c,0 {
+				compatible = "pci0014,7a19.0",
+						   "pci0014,7a19",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x6000 0x0 0x0 0x0 0x0>;
+				#interrupt-cells = <1>;
+				interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-parent = <&liointc1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &liointc1 3 IRQ_TYPE_LEVEL_LOW>;
+				external-facing;
+			};
+
+			pci_bridge@d,0 {
+				compatible = "pci0014,7a19.0",
+						   "pci0014,7a19",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x6800 0x0 0x0 0x0 0x0>;
+				#interrupt-cells = <1>;
+				interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-parent = <&liointc1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &liointc1 4 IRQ_TYPE_LEVEL_LOW>;
+				external-facing;
+			};
+
+			pci_bridge@e,0 {
+				compatible = "pci0014,7a19.0",
+						   "pci0014,7a19",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x7000 0x0 0x0 0x0 0x0>;
+				#interrupt-cells = <1>;
+				interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-parent = <&liointc1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &liointc1 5 IRQ_TYPE_LEVEL_LOW>;
+				external-facing;
+			};
+
+		};
+	};
+};
+

arch/mips/boot/dts/loongson/loongson64_2core_2k1000.dts

+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include "loongson64-2k1000.dtsi"
+
+/ {
+	compatible = "loongson,loongson64-2core-2k1000";
+};
+

arch/mips/cavium-octeon/oct_ilm.c

@@ -62,7 +62,7 @@ static int reset_statistics(void *data, u64 value)
 	return 0;
 }
 
-DEFINE_SIMPLE_ATTRIBUTE(reset_statistics_ops, NULL, reset_statistics, "%llu\n");
+DEFINE_DEBUGFS_ATTRIBUTE(reset_statistics_ops, NULL, reset_statistics, "%llu\n");
 
 static void init_debugfs(void)
 {

arch/mips/cavium-octeon/octeon-memcpy.S

@@ -150,8 +150,12 @@ LEAF(memcpy)					/* a0=dst a1=src a2=len */
 EXPORT_SYMBOL(memcpy)
 	move	v0, dst				/* return value */
 __memcpy:
-FEXPORT(__copy_user)
-EXPORT_SYMBOL(__copy_user)
+FEXPORT(__raw_copy_from_user)
+EXPORT_SYMBOL(__raw_copy_from_user)
+FEXPORT(__raw_copy_to_user)
+EXPORT_SYMBOL(__raw_copy_to_user)
+FEXPORT(__raw_copy_in_user)
+EXPORT_SYMBOL(__raw_copy_in_user)
 	/*
 	 * Note: dst & src may be unaligned, len may be 0
 	 * Temps

arch/mips/configs/bigsur_defconfig

@@ -105,10 +105,6 @@ CONFIG_BLK_DEV_CRYPTOLOOP=m
 CONFIG_BLK_DEV_NBD=m
 CONFIG_EEPROM_LEGACY=y
 CONFIG_EEPROM_MAX6875=y
-CONFIG_IDE=y
-CONFIG_BLK_DEV_IDECD=y
-CONFIG_BLK_DEV_IDETAPE=y
-CONFIG_BLK_DEV_TC86C001=m
 CONFIG_BLK_DEV_SD=y
 CONFIG_CHR_DEV_ST=y
 CONFIG_BLK_DEV_SR=y

arch/mips/configs/loongson2k_defconfig

+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_KERNEL_LZMA=y
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_AUDIT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_TASKSTATS=y
+CONFIG_TASK_DELAY_ACCT=y
+CONFIG_TASK_XACCT=y
+CONFIG_TASK_IO_ACCOUNTING=y
+CONFIG_MEMCG=y
+CONFIG_BLK_CGROUP=y
+CONFIG_SCHED_AUTOGROUP=y
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_RELAY=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EMBEDDED=y
+CONFIG_MACH_LOONGSON64=y
+# CONFIG_CPU_LOONGSON3_CPUCFG_EMULATION is not set
+CONFIG_HZ_256=y
+CONFIG_MIPS32_O32=y
+CONFIG_MIPS32_N32=y
+CONFIG_MODULES=y
+CONFIG_MODULE_FORCE_LOAD=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_MQ_IOSCHED_DEADLINE=m
+CONFIG_IOSCHED_BFQ=y
+CONFIG_BFQ_GROUP_IOSCHED=y
+CONFIG_BINFMT_MISC=m
+CONFIG_KSM=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=y
+CONFIG_NET_KEY=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_NETFILTER=y
+CONFIG_NETFILTER_NETLINK_LOG=m
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+CONFIG_NETFILTER_XT_TARGET_MARK=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_DCCP=m
+CONFIG_NETFILTER_XT_MATCH_ESP=m
+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MARK=m
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
+CONFIG_NETFILTER_XT_MATCH_STRING=m
+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
+CONFIG_IP_VS=m
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_MATCH_AH=m
+CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_TTL=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_TARGET_ECN=m
+CONFIG_IP_NF_TARGET_TTL=m
+CONFIG_IP_NF_RAW=m
+CONFIG_IP_NF_ARPTABLES=m
+CONFIG_IP_NF_ARPFILTER=m
+CONFIG_IP_NF_ARP_MANGLE=m
+CONFIG_IP_SCTP=m
+CONFIG_L2TP=m
+CONFIG_BRIDGE=m
+CONFIG_CFG80211=m
+CONFIG_CFG80211_WEXT=y
+CONFIG_MAC80211=m
+CONFIG_RFKILL=m
+CONFIG_RFKILL_INPUT=y
+CONFIG_PCIEPORTBUS=y
+CONFIG_HOTPLUG_PCI_PCIE=y
+CONFIG_PCIEASPM_PERFORMANCE=y
+CONFIG_HOTPLUG_PCI=y
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_MTD=m
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_CRYPTOLOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_RAID_ATTRS=m
+CONFIG_BLK_DEV_SD=y
+CONFIG_BLK_DEV_SR=y
+CONFIG_CHR_DEV_SG=y
+CONFIG_CHR_DEV_SCH=m
+CONFIG_SCSI_CONSTANTS=y
+CONFIG_SCSI_LOGGING=y
+CONFIG_SCSI_SPI_ATTRS=m
+CONFIG_SCSI_FC_ATTRS=m
+CONFIG_ISCSI_TCP=m
+CONFIG_MEGARAID_NEWGEN=y
+CONFIG_MEGARAID_MM=y
+CONFIG_MEGARAID_MAILBOX=y
+CONFIG_MEGARAID_LEGACY=y
+CONFIG_MEGARAID_SAS=y
+CONFIG_ATA=y
+CONFIG_SATA_AHCI=y
+CONFIG_PATA_ATIIXP=y
+CONFIG_MD=y
+CONFIG_BLK_DEV_MD=m
+CONFIG_MD_LINEAR=m
+CONFIG_MD_RAID0=m
+CONFIG_MD_RAID1=m
+CONFIG_MD_RAID10=m
+CONFIG_MD_RAID456=m
+CONFIG_MD_MULTIPATH=m
+CONFIG_BLK_DEV_DM=m
+CONFIG_DM_CRYPT=m
+CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_MIRROR=m
+CONFIG_DM_ZERO=m
+CONFIG_TARGET_CORE=m
+CONFIG_TCM_IBLOCK=m
+CONFIG_TCM_FILEIO=m
+CONFIG_TCM_PSCSI=m
+CONFIG_LOOPBACK_TARGET=m
+CONFIG_ISCSI_TARGET=m
+CONFIG_NETDEVICES=y
+CONFIG_TUN=m
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NET_VENDOR_ADAPTEC is not set
+# CONFIG_NET_VENDOR_ALTEON is not set
+# CONFIG_NET_VENDOR_AMD is not set
+# CONFIG_NET_VENDOR_ARC is not set
+# CONFIG_NET_VENDOR_ATHEROS is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_BROCADE is not set
+# CONFIG_NET_VENDOR_CHELSIO is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_CISCO is not set
+# CONFIG_NET_VENDOR_DEC is not set
+# CONFIG_NET_VENDOR_DLINK is not set
+# CONFIG_NET_VENDOR_EMULEX is not set
+# CONFIG_NET_VENDOR_I825XX is not set
+CONFIG_E1000=y
+CONFIG_E1000E=y
+CONFIG_IGB=y
+CONFIG_IXGB=y
+CONFIG_IXGBE=y
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MELLANOX is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_MICROCHIP is not set
+# CONFIG_NET_VENDOR_MICROSEMI is not set
+# CONFIG_NET_VENDOR_MYRI is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_NETERION is not set
+# CONFIG_NET_VENDOR_NETRONOME is not set
+# CONFIG_NET_VENDOR_NI is not set
+# CONFIG_NET_VENDOR_NVIDIA is not set
+# CONFIG_NET_VENDOR_OKI is not set
+# CONFIG_NET_VENDOR_PACKET_ENGINES is not set
+# CONFIG_NET_VENDOR_PENSANDO is not set
+# CONFIG_NET_VENDOR_QLOGIC is not set
+# CONFIG_NET_VENDOR_QUALCOMM is not set
+# CONFIG_NET_VENDOR_RDC is not set
+CONFIG_8139CP=y
+CONFIG_8139TOO=y
+# CONFIG_8139TOO_PIO is not set
+CONFIG_R8169=y
+# CONFIG_NET_VENDOR_RENESAS is not set
+# CONFIG_NET_VENDOR_ROCKER is not set
+# CONFIG_NET_VENDOR_SAMSUNG is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SOLARFLARE is not set
+# CONFIG_NET_VENDOR_SILAN is not set
+# CONFIG_NET_VENDOR_SIS is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+CONFIG_STMMAC_ETH=y
+# CONFIG_NET_VENDOR_SUN is not set
+# CONFIG_NET_VENDOR_TEHUTI is not set
+# CONFIG_NET_VENDOR_TI is not set
+# CONFIG_NET_VENDOR_TOSHIBA is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_PPP=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
+CONFIG_PPP_MPPE=m
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPPOE=m
+CONFIG_PPPOL2TP=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
+CONFIG_ATH9K=m
+CONFIG_HOSTAP=m
+CONFIG_INPUT_LEDS=m
+CONFIG_INPUT_SPARSEKMAP=y
+CONFIG_INPUT_EVDEV=y
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_XTKBD=m
+# CONFIG_MOUSE_PS2 is not set
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_UINPUT=m
+# CONFIG_SERIO_I8042 is not set
+CONFIG_SERIO_SERPORT=m
+CONFIG_SERIO_LIBPS2=y
+CONFIG_SERIO_RAW=m
+CONFIG_LEGACY_PTY_COUNT=16
+CONFIG_SERIAL_8250=y
+# CONFIG_SERIAL_8250_16550A_VARIANTS is not set
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=16
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_MANY_PORTS=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+CONFIG_SERIAL_8250_RSA=y
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIAL_NONSTANDARD=y
+CONFIG_HW_RANDOM=y
+CONFIG_RAW_DRIVER=m
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_PIIX4=y
+CONFIG_GPIO_LOONGSON=y
+CONFIG_SENSORS_LM75=m
+CONFIG_SENSORS_LM93=m
+CONFIG_SENSORS_W83627HF=m
+# CONFIG_MEDIA_CEC_SUPPORT is not set
+CONFIG_MEDIA_SUPPORT=m
+# CONFIG_MEDIA_CONTROLLER is not set
+CONFIG_MEDIA_USB_SUPPORT=y
+CONFIG_USB_VIDEO_CLASS=m
+CONFIG_DRM=y
+CONFIG_DRM_RADEON=y
+CONFIG_FB_RADEON=y
+CONFIG_LCD_CLASS_DEVICE=y
+CONFIG_LCD_PLATFORM=m
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
+CONFIG_LOGO=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_VERBOSE_PRINTK=y
+CONFIG_SND_SEQUENCER=y
+CONFIG_SND_SEQ_DUMMY=m
+# CONFIG_SND_ISA is not set
+CONFIG_SND_HDA_INTEL=y
+CONFIG_SND_HDA_HWDEP=y
+CONFIG_SND_HDA_PATCH_LOADER=y
+CONFIG_SND_HDA_CODEC_REALTEK=y
+CONFIG_SND_HDA_CODEC_ANALOG=y
+CONFIG_SND_HDA_CODEC_SIGMATEL=y
+CONFIG_SND_HDA_CODEC_VIA=y
+CONFIG_SND_HDA_CODEC_CONEXANT=y
+# CONFIG_SND_USB is not set
+CONFIG_SND_SOC=y
+CONFIG_HID_A4TECH=m
+CONFIG_HID_SUNPLUS=m
+CONFIG_USB=y
+CONFIG_USB_MON=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_UHCI_HCD=m
+CONFIG_USB_STORAGE=y
+CONFIG_USB_SERIAL=m
+CONFIG_USB_SERIAL_OPTION=m
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_CMOS=y
+CONFIG_DMADEVICES=y
+# CONFIG_CPU_HWMON is not set
+CONFIG_PM_DEVFREQ=y
+CONFIG_DEVFREQ_GOV_SIMPLE_ONDEMAND=y
+CONFIG_DEVFREQ_GOV_PERFORMANCE=y
+CONFIG_DEVFREQ_GOV_POWERSAVE=y
+CONFIG_DEVFREQ_GOV_USERSPACE=y
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+CONFIG_XFS_FS=y
+CONFIG_XFS_QUOTA=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_QUOTA=y
+# CONFIG_PRINT_QUOTA_WARNING is not set
+CONFIG_AUTOFS4_FS=y
+CONFIG_FUSE_FS=m
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=936
+CONFIG_FAT_DEFAULT_IOCHARSET="gb2312"
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_CRAMFS=m
+CONFIG_SQUASHFS=y
+CONFIG_SQUASHFS_XATTR=y
+CONFIG_NFS_FS=m
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=m
+CONFIG_NFSD=m
+CONFIG_NFSD_V3_ACL=y
+CONFIG_NFSD_V4=y
+CONFIG_CIFS=m
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_936=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_UTF8=y
+CONFIG_SECURITY=y
+CONFIG_SECURITYFS=y
+CONFIG_SECURITY_NETWORK=y
+CONFIG_SECURITY_PATH=y
+CONFIG_SECURITY_SELINUX=y
+CONFIG_SECURITY_SELINUX_BOOTPARAM=y
+CONFIG_SECURITY_SELINUX_DISABLE=y
+CONFIG_DEFAULT_SECURITY_DAC=y
+CONFIG_CRYPTO_SEQIV=m
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_TGR192=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_CRYPTO_DEFLATE=m
+CONFIG_PRINTK_TIME=y
+CONFIG_FRAME_WARN=1024
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+# CONFIG_FTRACE is not set

arch/mips/configs/loongson3_defconfig

@@ -26,6 +26,7 @@ CONFIG_SCHED_AUTOGROUP=y
 CONFIG_SYSFS_DEPRECATED=y
 CONFIG_RELAY=y
 CONFIG_BLK_DEV_INITRD=y
+CONFIG_BPF_SYSCALL=y
 CONFIG_EMBEDDED=y
 CONFIG_PERF_EVENTS=y
 CONFIG_MACH_LOONGSON64=y
@@ -39,7 +40,7 @@ CONFIG_MIPS32_O32=y
 CONFIG_MIPS32_N32=y
 CONFIG_VIRTUALIZATION=y
 CONFIG_KVM=m
-CONFIG_KVM_MIPS_VZ=y
+CONFIG_KPROBES=y
 CONFIG_MODULES=y
 CONFIG_MODULE_FORCE_LOAD=y
 CONFIG_MODULE_UNLOAD=y
@@ -129,6 +130,7 @@ CONFIG_L2TP=m
 CONFIG_BRIDGE=m
 CONFIG_VSOCKETS=m
 CONFIG_VIRTIO_VSOCKETS=m
+CONFIG_BPF_JIT=y
 CONFIG_CFG80211=m
 CONFIG_CFG80211_WEXT=y
 CONFIG_MAC80211=m
@@ -318,6 +320,7 @@ CONFIG_USB_OHCI_HCD=y
 CONFIG_USB_UHCI_HCD=m
 CONFIG_USB_STORAGE=m
 CONFIG_USB_SERIAL=m
+CONFIG_USB_SERIAL_PL2303=m
 CONFIG_USB_SERIAL_OPTION=m
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_CMOS=y
@@ -405,8 +408,10 @@ CONFIG_CRYPTO_DEFLATE=m
 CONFIG_PRINTK_TIME=y
 CONFIG_STRIP_ASM_SYMS=y
 CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_FS=y
 # CONFIG_SCHED_DEBUG is not set
 # CONFIG_DEBUG_PREEMPT is not set
-# CONFIG_FTRACE is not set
+CONFIG_FUNCTION_TRACER=y
+CONFIG_FTRACE_SYSCALLS=y
 CONFIG_CMDLINE_BOOL=y
 CONFIG_CMDLINE="ieee754=relaxed"

arch/mips/configs/malta_kvm_defconfig

@@ -238,9 +238,6 @@ CONFIG_BLK_DEV_NBD=m
 CONFIG_BLK_DEV_RAM=y
 CONFIG_CDROM_PKTCDVD=m
 CONFIG_ATA_OVER_ETH=m
-CONFIG_IDE=y
-CONFIG_BLK_DEV_IDECD=y
-CONFIG_BLK_DEV_TC86C001=m
 CONFIG_RAID_ATTRS=m
 CONFIG_BLK_DEV_SD=y
 CONFIG_CHR_DEV_ST=m

arch/mips/configs/maltaup_xpa_defconfig

@@ -236,9 +236,6 @@ CONFIG_BLK_DEV_NBD=m
 CONFIG_BLK_DEV_RAM=y
 CONFIG_CDROM_PKTCDVD=m
 CONFIG_ATA_OVER_ETH=m
-CONFIG_IDE=y
-CONFIG_BLK_DEV_IDECD=y
-CONFIG_BLK_DEV_TC86C001=m
 CONFIG_RAID_ATTRS=m
 CONFIG_BLK_DEV_SD=y
 CONFIG_CHR_DEV_ST=m

arch/mips/configs/rbtx49xx_defconfig

@@ -44,9 +44,6 @@ CONFIG_MTD_NAND_TXX9NDFMC=m
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_IDE=y
-CONFIG_BLK_DEV_IDE_TX4938=y
-CONFIG_BLK_DEV_IDE_TX4939=y
 CONFIG_NETDEVICES=y
 CONFIG_NE2000=y
 CONFIG_SMC91X=y

arch/mips/configs/sb1250_swarm_defconfig

@@ -17,7 +17,6 @@ CONFIG_64BIT=y
 CONFIG_SMP=y
 CONFIG_NR_CPUS=2
 CONFIG_HZ_1000=y
-CONFIG_PCI=y
 CONFIG_MIPS32_O32=y
 CONFIG_PM=y
 CONFIG_MODULES=y
@@ -34,25 +33,28 @@ CONFIG_INET=y
 CONFIG_IP_PNP=y
 CONFIG_IP_PNP_DHCP=y
 CONFIG_IP_PNP_BOOTP=y
-CONFIG_INET_XFRM_MODE_TRANSPORT=m
-CONFIG_INET_XFRM_MODE_TUNNEL=m
-CONFIG_INET_XFRM_MODE_BEET=m
 CONFIG_TCP_MD5SIG=y
 # CONFIG_IPV6 is not set
 CONFIG_NETWORK_SECMARK=y
 CONFIG_CFG80211=m
 CONFIG_MAC80211=m
 CONFIG_RFKILL=m
+CONFIG_PCI=y
 CONFIG_FW_LOADER=m
 CONFIG_CONNECTOR=m
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=9220
 CONFIG_CDROM_PKTCDVD=m
 CONFIG_ATA_OVER_ETH=m
-CONFIG_IDE=y
-CONFIG_BLK_DEV_IDECD=y
-CONFIG_BLK_DEV_IDETAPE=y
 CONFIG_RAID_ATTRS=m
+CONFIG_BLK_DEV_SD=y
+CONFIG_BLK_DEV_SR=y
+CONFIG_CHR_DEV_SG=y
+CONFIG_SCSI_CONSTANTS=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_ATA=y
+# CONFIG_ATA_BMDMA is not set
+CONFIG_PATA_PLATFORM=y
 CONFIG_NETDEVICES=y
 CONFIG_MACVLAN=m
 CONFIG_SB1250_MAC=y
@@ -88,18 +90,14 @@ CONFIG_CRYPTO_MICHAEL_MIC=m
 CONFIG_CRYPTO_SHA512=m
 CONFIG_CRYPTO_TGR192=m
 CONFIG_CRYPTO_WP512=m
-CONFIG_CRYPTO_ANUBIS=m
 CONFIG_CRYPTO_BLOWFISH=m
 CONFIG_CRYPTO_CAMELLIA=m
 CONFIG_CRYPTO_CAST5=m
 CONFIG_CRYPTO_CAST6=m
 CONFIG_CRYPTO_DES=m
 CONFIG_CRYPTO_FCRYPT=m
-CONFIG_CRYPTO_KHAZAD=m
 CONFIG_CRYPTO_SALSA20=m
-CONFIG_CRYPTO_SEED=m
 CONFIG_CRYPTO_SERPENT=m
-CONFIG_CRYPTO_TEA=m
 CONFIG_CRYPTO_TWOFISH=m
 CONFIG_CRYPTO_DEFLATE=m
 CONFIG_CRYPTO_LZO=m

arch/mips/configs/workpad_defconfig

@@ -26,9 +26,12 @@ CONFIG_IP_MULTICAST=y
 # CONFIG_IPV6 is not set
 CONFIG_NETWORK_SECMARK=y
 CONFIG_BLK_DEV_RAM=m
-CONFIG_IDE=y
-CONFIG_BLK_DEV_IDECS=m
-CONFIG_IDE_GENERIC=y
+# CONFIG_SCSI_PROC_FS is not set
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_ATA=y
+# CONFIG_ATA_VERBOSE_ERROR is not set
+# CONFIG_ATA_FORCE is not set
+# CONFIG_ATA_BMDMA is not set
 CONFIG_NETDEVICES=y
 CONFIG_PCMCIA_3C574=m
 CONFIG_PCMCIA_3C589=m

arch/mips/crypto/.gitignore

+# SPDX-License-Identifier: GPL-2.0-only
+poly1305-core.S

arch/mips/generic/board-boston.its.S

 / {
 	images {
-		fdt@boston {
+		fdt-boston {
 			description = "img,boston Device Tree";
 			data = /incbin/("boot/dts/img/boston.dtb");
 			type = "flat_dt";
 			arch = "mips";
 			compression = "none";
-			hash@0 {
+			hash {
 				algo = "sha1";
 			};
 		};
 	};
 
 	configurations {
-		conf@boston {
+		conf-boston {
 			description = "Boston Linux kernel";
-			kernel = "kernel@0";
-			fdt = "fdt@boston";
+			kernel = "kernel";
+			fdt = "fdt-boston";
 		};
 	};
 };

arch/mips/generic/board-jaguar2.its.S

 /* SPDX-License-Identifier: (GPL-2.0 OR MIT) */
 / {
 	images {
-		fdt@jaguar2_pcb110 {
+		fdt-jaguar2_pcb110 {
 			description = "MSCC Jaguar2 PCB110 Device Tree";
 			data = /incbin/("boot/dts/mscc/jaguar2_pcb110.dtb");
 			type = "flat_dt";
 			arch = "mips";
 			compression = "none";
-			hash@0 {
+			hash {
 				algo = "sha1";
 			};
 		};
-		fdt@jaguar2_pcb111 {
+		fdt-jaguar2_pcb111 {
 			description = "MSCC Jaguar2 PCB111 Device Tree";
 			data = /incbin/("boot/dts/mscc/jaguar2_pcb111.dtb");
 			type = "flat_dt";
 			arch = "mips";
 			compression = "none";
-			hash@0 {
+			hash {
 				algo = "sha1";
 			};
 		};
@@ -26,14 +26,14 @@
 	configurations {
 		pcb110 {
 			description = "Jaguar2 Linux kernel";
-			kernel = "kernel@0";
-			fdt = "fdt@jaguar2_pcb110";
+			kernel = "kernel";
+			fdt = "fdt-jaguar2_pcb110";
 			ramdisk = "ramdisk";
 		};
 		pcb111 {
 			description = "Jaguar2 Linux kernel";
-			kernel = "kernel@0";
-			fdt = "fdt@jaguar2_pcb111";
+			kernel = "kernel";
+			fdt = "fdt-jaguar2_pcb111";
 			ramdisk = "ramdisk";
 		};
 	};

arch/mips/generic/board-luton.its.S

 /* SPDX-License-Identifier: (GPL-2.0 OR MIT) */
 / {
 	images {
-		fdt@luton_pcb091 {
+		fdt-luton_pcb091 {
 			description = "MSCC Luton PCB091 Device Tree";
 			data = /incbin/("boot/dts/mscc/luton_pcb091.dtb");
 			type = "flat_dt";
 			arch = "mips";
 			compression = "none";
-			hash@0 {
+			hash {
 				algo = "sha1";
 			};
 		};
@@ -16,8 +16,8 @@
 	configurations {
 		pcb091 {
 			description = "Luton Linux kernel";
-			kernel = "kernel@0";
-			fdt = "fdt@luton_pcb091";
+			kernel = "kernel";
+			fdt = "fdt-luton_pcb091";
 		};
 	};
 };

arch/mips/generic/board-ni169445.its.S

 / {
 	images {
-		fdt@ni169445 {
+		fdt-ni169445 {
 			description = "NI 169445 device tree";
 			data = /incbin/("boot/dts/ni/169445.dtb");
 			type = "flat_dt";
 			arch = "mips";
 			compression = "none";
-			hash@0 {
+			hash {
 				algo = "sha1";
 			};
 		};
 	};
 
 	configurations {
-		conf@ni169445 {
+		conf-ni169445 {
 			description = "NI 169445 Linux Kernel";
-			kernel = "kernel@0";
-			fdt = "fdt@ni169445";
+			kernel = "kernel";
+			fdt = "fdt-ni169445";
 		};
 	};
 };

arch/mips/generic/board-ocelot.its.S

 /* SPDX-License-Identifier: (GPL-2.0 OR MIT) */
 / {
 	images {
-		fdt@ocelot_pcb123 {
+		fdt-ocelot_pcb123 {
 			description = "MSCC Ocelot PCB123 Device Tree";
 			data = /incbin/("boot/dts/mscc/ocelot_pcb123.dtb");
 			type = "flat_dt";
 			arch = "mips";
 			compression = "none";
-			hash@0 {
+			hash {
 				algo = "sha1";
 			};
 		};
 
-		fdt@ocelot_pcb120 {
+		fdt-ocelot_pcb120 {
 			description = "MSCC Ocelot PCB120 Device Tree";
 			data = /incbin/("boot/dts/mscc/ocelot_pcb120.dtb");
 			type = "flat_dt";
 			arch = "mips";
 			compression = "none";
-			hash@0 {
+			hash {
 				algo = "sha1";
 			};
 		};
 	};
 
 	configurations {
-		conf@ocelot_pcb123 {
+		conf-ocelot_pcb123 {
 			description = "Ocelot Linux kernel";
-			kernel = "kernel@0";
-			fdt = "fdt@ocelot_pcb123";
+			kernel = "kernel";
+			fdt = "fdt-ocelot_pcb123";
 		};
 
-		conf@ocelot_pcb120 {
+		conf-ocelot_pcb120 {
 			description = "Ocelot Linux kernel";
-			kernel = "kernel@0";
-			fdt = "fdt@ocelot_pcb120";
+			kernel = "kernel";
+			fdt = "fdt-ocelot_pcb120";
 		};
 	};
 };

arch/mips/generic/board-serval.its.S

 /* SPDX-License-Identifier: (GPL-2.0 OR MIT) */
 / {
 	images {
-		fdt@serval_pcb105 {
+		fdt-serval_pcb105 {
 			description = "MSCC Serval PCB105 Device Tree";
 			data = /incbin/("boot/dts/mscc/serval_pcb105.dtb");
 			type = "flat_dt";
 			arch = "mips";
 			compression = "none";
-			hash@0 {
+			hash {
 				algo = "sha1";
 			};
 		};
@@ -16,8 +16,8 @@
 	configurations {
 		pcb105 {
 			description = "Serval Linux kernel";
-			kernel = "kernel@0";
-			fdt = "fdt@serval_pcb105";
+			kernel = "kernel";
+			fdt = "fdt-serval_pcb105";
 			ramdisk = "ramdisk";
 		};
 	};

arch/mips/generic/board-xilfpga.its.S

 / {
 	images {
-		fdt@xilfpga {
+		fdt-xilfpga {
 			description = "MIPSfpga (xilfpga) Device Tree";
 			data = /incbin/("boot/dts/xilfpga/nexys4ddr.dtb");
 			type = "flat_dt";
 			arch = "mips";
 			compression = "none";
-			hash@0 {
+			hash {
 				algo = "sha1";
 			};
 		};
 	};
 
 	configurations {
-		conf@xilfpga {
+		conf-xilfpga {
 			description = "MIPSfpga Linux kernel";
-			kernel = "kernel@0";
-			fdt = "fdt@xilfpga";
+			kernel = "kernel";
+			fdt = "fdt-xilfpga";
 		};
 	};
 };

arch/mips/generic/vmlinux.its.S

@@ -6,7 +6,7 @@
 	#address-cells = <ADDR_CELLS>;
 
 	images {
-		kernel@0 {
+		kernel {
 			description = KERNEL_NAME;
 			data = /incbin/(VMLINUX_BINARY);
 			type = "kernel";
@@ -15,18 +15,18 @@
 			compression = VMLINUX_COMPRESSION;
 			load = /bits/ ADDR_BITS <VMLINUX_LOAD_ADDRESS>;
 			entry = /bits/ ADDR_BITS <VMLINUX_ENTRY_ADDRESS>;
-			hash@0 {
+			hash {
 				algo = "sha1";
 			};
 		};
 	};
 
 	configurations {
-		default = "conf@default";
+		default = "conf-default";
 
-		conf@default {
+		conf-default {
 			description = "Generic Linux kernel";
-			kernel = "kernel@0";
+			kernel = "kernel";
 		};
 	};
 };

arch/mips/include/asm/Kbuild

 # SPDX-License-Identifier: GPL-2.0
 # MIPS headers
-generated-y += syscall_table_32_o32.h
-generated-y += syscall_table_64_n32.h
-generated-y += syscall_table_64_n64.h
-generated-y += syscall_table_64_o32.h
+generated-y += syscall_table_n32.h
+generated-y += syscall_table_n64.h
+generated-y += syscall_table_o32.h
 generated-y += unistd_nr_n32.h
 generated-y += unistd_nr_n64.h
 generated-y += unistd_nr_o32.h

arch/mips/include/asm/asmmacro.h

@@ -44,8 +44,7 @@
 	.endm
 #endif
 
-#if defined(CONFIG_CPU_MIPSR2) || defined(CONFIG_CPU_MIPSR5) || \
-    defined(CONFIG_CPU_MIPSR6)
+#ifdef CONFIG_CPU_HAS_DIEI
 	.macro	local_irq_enable reg=t0
 	ei
 	irq_enable_hazard

arch/mips/include/asm/bootinfo.h

@@ -107,7 +107,7 @@ extern void (*free_init_pages_eva)(void *begin, void *end);
 extern char arcs_cmdline[COMMAND_LINE_SIZE];
 
 /*
- * Registers a0, a1, a3 and a4 as passed to the kernel entry by firmware
+ * Registers a0, a1, a2 and a3 as passed to the kernel entry by firmware
  */
 extern unsigned long fw_arg0, fw_arg1, fw_arg2, fw_arg3;
 

arch/mips/include/asm/div64.h

 /*
- * Copyright (C) 2000, 2004  Maciej W. Rozycki
+ * Copyright (C) 2000, 2004, 2021  Maciej W. Rozycki
  * Copyright (C) 2003, 07 Ralf Baechle (ralf@linux-mips.org)
  *
  * This file is subject to the terms and conditions of the GNU General Public
@@ -9,25 +9,18 @@
 #ifndef __ASM_DIV64_H
 #define __ASM_DIV64_H
 
-#include <asm-generic/div64.h>
-
-#if BITS_PER_LONG == 64
+#include <asm/bitsperlong.h>
 
-#include <linux/types.h>
+#if BITS_PER_LONG == 32
 
 /*
  * No traps on overflows for any of these...
  */
 
-#define __div64_32(n, base)						\
-({									\
+#define do_div64_32(res, high, low, base) ({				\
 	unsigned long __cf, __tmp, __tmp2, __i;				\
 	unsigned long __quot32, __mod32;				\
-	unsigned long __high, __low;					\
-	unsigned long long __n;						\
 									\
-	__high = *__n >> 32;						\
-	__low = __n;							\
 	__asm__(							\
 	"	.set	push					\n"	\
 	"	.set	noat					\n"	\
@@ -51,18 +44,48 @@
 	"	subu	%0, %0, %z6				\n"	\
 	"	addiu	%2, %2, 1				\n"	\
 	"3:							\n"	\
-	"	bnez	%4, 0b\n\t"					\
-	"	 srl	%5, %1, 0x1f\n\t"				\
+	"	bnez	%4, 0b					\n"	\
+	"	 srl	%5, %1, 0x1f				\n"	\
 	"	.set	pop"						\
 	: "=&r" (__mod32), "=&r" (__tmp),				\
 	  "=&r" (__quot32), "=&r" (__cf),				\
 	  "=&r" (__i), "=&r" (__tmp2)					\
-	: "Jr" (base), "0" (__high), "1" (__low));			\
+	: "Jr" (base), "0" (high), "1" (low));				\
 									\
-	(__n) = __quot32;						\
+	(res) = __quot32;						\
 	__mod32;							\
 })
 
-#endif /* BITS_PER_LONG == 64 */
+#define __div64_32(n, base) ({						\
+	unsigned long __upper, __low, __high, __radix;			\
+	unsigned long long __quot;					\
+	unsigned long long __div;					\
+	unsigned long __mod;						\
+									\
+	__div = (*n);							\
+	__radix = (base);						\
+									\
+	__high = __div >> 32;						\
+	__low = __div;							\
+									\
+	if (__high < __radix) {						\
+		__upper = __high;					\
+		__high = 0;						\
+	} else {							\
+		__upper = __high % __radix;				\
+		__high /= __radix;					\
+	}								\
+									\
+	__mod = do_div64_32(__low, __upper, __low, __radix);		\
+									\
+	__quot = __high;						\
+	__quot = __quot << 32 | __low;					\
+	(*n) = __quot;							\
+	__mod;								\
+})
+
+#endif /* BITS_PER_LONG == 32 */
+
+#include <asm-generic/div64.h>
 
 #endif /* __ASM_DIV64_H */

arch/mips/include/asm/io.h

@@ -100,11 +100,23 @@ static inline void set_io_port_base(unsigned long base)
  *     almost all conceivable cases a device driver should not be using
  *     this function
  */
-static inline unsigned long virt_to_phys(volatile const void *address)
+static inline unsigned long __virt_to_phys_nodebug(volatile const void *address)
 {
 	return __pa(address);
 }
 
+#ifdef CONFIG_DEBUG_VIRTUAL
+extern phys_addr_t __virt_to_phys(volatile const void *x);
+#else
+#define __virt_to_phys(x)	__virt_to_phys_nodebug(x)
+#endif
+
+#define virt_to_phys virt_to_phys
+static inline phys_addr_t virt_to_phys(const volatile void *x)
+{
+	return __virt_to_phys(x);
+}
+
 /*
  *     phys_to_virt    -       map physical address to virtual
  *     @address: address to remap

arch/mips/include/asm/mach-cavium-octeon/kernel-entry-init.h

@@ -157,4 +157,12 @@
 	.macro	smp_slave_setup
 	.endm
 
+#define USE_KEXEC_SMP_WAIT_FINAL
+	.macro  kexec_smp_wait_final
+	.set push
+	.set noreorder
+	synci		0($0)
+	.set pop
+	.endm
+
 #endif /* __ASM_MACH_CAVIUM_OCTEON_KERNEL_ENTRY_H */

arch/mips/include/asm/mach-generic/spaces.h

@@ -30,11 +30,7 @@
 #endif /* __ASSEMBLY__ */
 
 #ifdef CONFIG_32BIT
-#ifdef CONFIG_KVM_GUEST
-#define CAC_BASE		_AC(0x40000000, UL)
-#else
 #define CAC_BASE		_AC(0x80000000, UL)
-#endif
 #ifndef IO_BASE
 #define IO_BASE			_AC(0xa0000000, UL)
 #endif
@@ -43,12 +39,8 @@
 #endif
 
 #ifndef MAP_BASE
-#ifdef CONFIG_KVM_GUEST
-#define MAP_BASE		_AC(0x60000000, UL)
-#else
 #define MAP_BASE		_AC(0xc0000000, UL)
 #endif
-#endif
 
 /*
  * Memory above this physical address will be considered highmem.
@@ -100,11 +92,7 @@
 #endif
 
 #ifndef FIXADDR_TOP
-#ifdef CONFIG_KVM_GUEST
-#define FIXADDR_TOP		((unsigned long)(long)(int)0x7ffe0000)
-#else
 #define FIXADDR_TOP		((unsigned long)(long)(int)0xfffe0000)
 #endif
-#endif
 
 #endif /* __ASM_MACH_GENERIC_SPACES_H */

arch/mips/include/asm/mach-loongson64/boot_param.h

@@ -198,33 +198,6 @@ enum loongson_bridge_type {
 	VIRTUAL = 3
 };
 
-struct loongson_system_configuration {
-	u32 nr_cpus;
-	u32 nr_nodes;
-	int cores_per_node;
-	int cores_per_package;
-	u16 boot_cpu_id;
-	u16 reserved_cpus_mask;
-	enum loongson_cpu_type cputype;
-	enum loongson_bridge_type bridgetype;
-	u64 ht_control_base;
-	u64 pci_mem_start_addr;
-	u64 pci_mem_end_addr;
-	u64 pci_io_base;
-	u64 restart_addr;
-	u64 poweroff_addr;
-	u64 suspend_addr;
-	u64 vgabios_addr;
-	u32 dma_mask_bits;
-	char ecname[32];
-	u32 nr_uarts;
-	struct uart_device uarts[MAX_UARTS];
-	u32 nr_sensors;
-	struct sensor_device sensors[MAX_SENSORS];
-	u64 workarounds;
-	void (*early_config)(void);
-};
-
 extern struct efi_memory_map_loongson *loongson_memmap;
 extern struct loongson_system_configuration loongson_sysconf;
 

arch/mips/include/asm/mach-loongson64/builtin_dtbs.h

@@ -8,6 +8,7 @@
 #ifndef __ASM_MACH_LOONGSON64_BUILTIN_DTBS_H_
 #define __ASM_MACH_LOONGSON64_BUILTIN_DTBS_H_
 
+extern u32 __dtb_loongson64_2core_2k1000_begin[];
 extern u32 __dtb_loongson64c_4core_ls7a_begin[];
 extern u32 __dtb_loongson64c_4core_rs780e_begin[];
 extern u32 __dtb_loongson64c_8core_rs780e_begin[];

arch/mips/include/asm/mach-loongson64/kernel-entry-init.h

@@ -75,4 +75,31 @@
 	.set	pop
 	.endm
 
+#define USE_KEXEC_SMP_WAIT_FINAL
+	.macro  kexec_smp_wait_final
+	/* s0:prid s1:initfn */
+	/* a0:base t1:cpuid t2:node t9:count */
+	mfc0		t1, CP0_EBASE
+	andi		t1, MIPS_EBASE_CPUNUM
+	dins		a0, t1, 8, 2       /* insert core id*/
+	dext		t2, t1, 2, 2
+	dins		a0, t2, 44, 2      /* insert node id */
+	mfc0		s0, CP0_PRID
+	andi		s0, s0, (PRID_IMP_MASK | PRID_REV_MASK)
+	beq		s0, (PRID_IMP_LOONGSON_64C | PRID_REV_LOONGSON3B_R1), 1f
+	beq		s0, (PRID_IMP_LOONGSON_64C | PRID_REV_LOONGSON3B_R2), 1f
+	b		2f                 /* Loongson-3A1000/3A2000/3A3000/3A4000 */
+1:	dins		a0, t2, 14, 2      /* Loongson-3B1000/3B1500 need bit 15~14 */
+2:	li		t9, 0x100          /* wait for init loop */
+3:	addiu		t9, -1             /* limit mailbox access */
+	bnez		t9, 3b
+	lw		s1, 0x20(a0)       /* check PC as an indicator */
+	beqz		s1, 2b
+	ld		s1, 0x20(a0)       /* get PC via mailbox reg0 */
+	ld		sp, 0x28(a0)       /* get SP via mailbox reg1 */
+	ld		gp, 0x30(a0)       /* get GP via mailbox reg2 */
+	ld		a1, 0x38(a0)
+	jr		s1                 /* jump to initial PC */
+	.endm
+
 #endif /* __ASM_MACH_LOONGSON64_KERNEL_ENTRY_H */

arch/mips/include/asm/mach-loongson64/loongson.h

@@ -12,6 +12,30 @@
 #include <linux/irq.h>
 #include <boot_param.h>
 
+enum loongson_fw_interface {
+	LOONGSON_LEFI,
+	LOONGSON_DTB,
+};
+
+/* machine-specific boot configuration */
+struct loongson_system_configuration {
+	enum loongson_fw_interface fw_interface;
+	u32 nr_cpus;
+	u32 nr_nodes;
+	int cores_per_node;
+	int cores_per_package;
+	u16 boot_cpu_id;
+	u16 reserved_cpus_mask;
+	enum loongson_cpu_type cputype;
+	enum loongson_bridge_type bridgetype;
+	u64 restart_addr;
+	u64 poweroff_addr;
+	u64 suspend_addr;
+	u64 vgabios_addr;
+	u32 dma_mask_bits;
+	u64 workarounds;
+	void (*early_config)(void);
+};
 
 /* machine-specific reboot/halt operation */
 extern void mach_prepare_reboot(void);
@@ -23,7 +47,8 @@ extern u32 memsize, highmemsize;
 extern const struct plat_smp_ops loongson3_smp_ops;
 
 /* loongson-specific command line, env and memory initialization */
-extern void __init prom_init_env(void);
+extern void __init prom_dtb_init_env(void);
+extern void __init prom_lefi_init_env(void);
 extern void __init szmem(unsigned int node);
 extern void *loongson_fdt_blob;
 

arch/mips/include/asm/mach-ralink/mt7621.h

@@ -24,9 +24,10 @@
 #define CHIP_REV_VER_SHIFT		8
 #define CHIP_REV_ECO_MASK		0xf
 
-#define MT7621_DRAM_BASE                0x0
-#define MT7621_DDR2_SIZE_MIN		32
-#define MT7621_DDR2_SIZE_MAX		256
+#define MT7621_LOWMEM_BASE		0x0
+#define MT7621_LOWMEM_MAX_SIZE		0x1C000000
+#define MT7621_HIGHMEM_BASE		0x20000000
+#define MT7621_HIGHMEM_SIZE		0x4000000
 
 #define MT7621_CHIP_NAME0		0x3637544D
 #define MT7621_CHIP_NAME1		0x20203132

arch/mips/include/asm/mips-cps.h

@@ -10,6 +10,8 @@
 #include <linux/io.h>
 #include <linux/types.h>
 
+#include <asm/mips-boards/launch.h>
+
 extern unsigned long __cps_access_bad_size(void)
 	__compiletime_error("Bad size for CPS accessor");
 
@@ -165,11 +167,30 @@ static inline uint64_t mips_cps_cluster_config(unsigned int cluster)
  */
 static inline unsigned int mips_cps_numcores(unsigned int cluster)
 {
+	unsigned int ncores;
+
 	if (!mips_cm_present())
 		return 0;
 
 	/* Add one before masking to handle 0xff indicating no cores */
-	return (mips_cps_cluster_config(cluster) + 1) & CM_GCR_CONFIG_PCORES;
+	ncores = (mips_cps_cluster_config(cluster) + 1) & CM_GCR_CONFIG_PCORES;
+
+	if (IS_ENABLED(CONFIG_SOC_MT7621)) {
+		struct cpulaunch *launch;
+
+		/*
+		 * Ralink MT7621S SoC is single core, but the GCR_CONFIG method
+		 * always reports 2 cores. Check the second core's LAUNCH_FREADY
+		 * flag to detect if the second core is missing. This method
+		 * only works before the core has been started.
+		 */
+		launch = (struct cpulaunch *)CKSEG0ADDR(CPULAUNCH);
+		launch += 2; /* MT7621 has 2 VPEs per core */
+		if (!(launch->flags & LAUNCH_FREADY))
+			ncores = 1;
+	}
+
+	return ncores;
 }
 
 /**

arch/mips/include/asm/octeon/cvmx-address.h

@@ -152,7 +152,7 @@ typedef union {
 
 	/* physical mem address */
 	struct {
-		/* techically, <47:40> are dont-cares */
+		/* technically, <47:40> are dont-cares */
 		uint64_t zeroes:24;
 		/* the hardware ignores <39:36> in Octeon I */
 		uint64_t unaddr:4;

arch/mips/include/asm/octeon/cvmx-bootinfo.h

@@ -298,6 +298,7 @@ enum cvmx_board_types_enum {
 	CVMX_BOARD_TYPE_UBNT_E200 = 20003,
 	CVMX_BOARD_TYPE_UBNT_E220 = 20005,
 	CVMX_BOARD_TYPE_CUST_DSR1000N = 20006,
+	CVMX_BOARD_TYPE_UBNT_E300 = 20300,
 	CVMX_BOARD_TYPE_KONTRON_S1901 = 21901,
 	CVMX_BOARD_TYPE_CUST_PRIVATE_MAX = 30000,
 
@@ -401,6 +402,7 @@ static inline const char *cvmx_board_type_to_string(enum
 		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_UBNT_E200)
 		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_UBNT_E220)
 		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_DSR1000N)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_UBNT_E300)
 		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_KONTRON_S1901)
 		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_PRIVATE_MAX)
 	}

arch/mips/include/asm/page.h

@@ -210,9 +210,16 @@ static inline unsigned long ___pa(unsigned long x)
  * also affect MIPS so we keep this one until GCC 3.x has been retired
  * before we can apply https://patchwork.linux-mips.org/patch/1541/
  */
+#define __pa_symbol_nodebug(x)	__pa(RELOC_HIDE((unsigned long)(x), 0))
+
+#ifdef CONFIG_DEBUG_VIRTUAL
+extern phys_addr_t __phys_addr_symbol(unsigned long x);
+#else
+#define __phys_addr_symbol(x)	__pa_symbol_nodebug(x)
+#endif
 
 #ifndef __pa_symbol
-#define __pa_symbol(x)	__pa(RELOC_HIDE((unsigned long)(x), 0))
+#define __pa_symbol(x)		__phys_addr_symbol((unsigned long)(x))
 #endif
 
 #define pfn_to_kaddr(pfn)	__va((pfn) << PAGE_SHIFT)

arch/mips/include/asm/pci.h

@@ -38,7 +38,6 @@ struct pci_controller {
 	struct resource *io_resource;
 	unsigned long io_offset;
 	unsigned long io_map_base;
-	struct resource *busn_resource;
 
 #ifndef CONFIG_PCI_DOMAINS_GENERIC
 	unsigned int index;

arch/mips/include/asm/processor.h

@@ -32,16 +32,11 @@ extern unsigned int vced_count, vcei_count;
 extern int arch_dup_task_struct(struct task_struct *dst, struct task_struct *src);
 
 #ifdef CONFIG_32BIT
-#ifdef CONFIG_KVM_GUEST
-/* User space process size is limited to 1GB in KVM Guest Mode */
-#define TASK_SIZE	0x3fff8000UL
-#else
 /*
  * User space process size: 2GB. This is hardcoded into a few places,
  * so don't change it unless you know what you are doing.
  */
 #define TASK_SIZE	0x80000000UL
-#endif
 
 #define STACK_TOP_MAX	TASK_SIZE
 
@@ -226,10 +221,6 @@ struct nlm_cop2_state {
 #define COP2_INIT
 #endif
 
-typedef struct {
-	unsigned long seg;
-} mm_segment_t;
-
 #ifdef CONFIG_CPU_HAS_MSA
 # define ARCH_MIN_TASKALIGN	16
 # define FPU_ALIGN		__aligned(16)

arch/mips/include/asm/thread_info.h

@@ -28,11 +28,6 @@ struct thread_info {
 	unsigned long		tp_value;	/* thread pointer */
 	__u32			cpu;		/* current CPU */
 	int			preempt_count;	/* 0 => preemptable, <0 => BUG */
-	mm_segment_t		addr_limit;	/*
-						 * thread address space limit:
-						 * 0x7fffffff for user-thead
-						 * 0xffffffff for kernel-thread
-						 */
 	struct pt_regs		*regs;
 	long			syscall;	/* syscall number */
 };
@@ -46,7 +41,6 @@ struct thread_info {
 	.flags		= _TIF_FIXADE,		\
 	.cpu		= 0,			\
 	.preempt_count	= INIT_PREEMPT_COUNT,	\
-	.addr_limit	= KERNEL_DS,		\
 }
 
 /*

arch/mips/include/asm/vdso/gettimeofday.h

@@ -20,6 +20,12 @@
 
 #define VDSO_HAS_CLOCK_GETRES		1
 
+#if MIPS_ISA_REV < 6
+#define VDSO_SYSCALL_CLOBBERS "hi", "lo",
+#else
+#define VDSO_SYSCALL_CLOBBERS
+#endif
+
 static __always_inline long gettimeofday_fallback(
 				struct __kernel_old_timeval *_tv,
 				struct timezone *_tz)
@@ -35,7 +41,9 @@ static __always_inline long gettimeofday_fallback(
 	: "=r" (ret), "=r" (error)
 	: "r" (tv), "r" (tz), "r" (nr)
 	: "$1", "$3", "$8", "$9", "$10", "$11", "$12", "$13",
-	  "$14", "$15", "$24", "$25", "hi", "lo", "memory");
+	  "$14", "$15", "$24", "$25",
+	  VDSO_SYSCALL_CLOBBERS
+	  "memory");
 
 	return error ? -ret : ret;
 }
@@ -59,7 +67,9 @@ static __always_inline long clock_gettime_fallback(
 	: "=r" (ret), "=r" (error)
 	: "r" (clkid), "r" (ts), "r" (nr)
 	: "$1", "$3", "$8", "$9", "$10", "$11", "$12", "$13",
-	  "$14", "$15", "$24", "$25", "hi", "lo", "memory");
+	  "$14", "$15", "$24", "$25",
+	  VDSO_SYSCALL_CLOBBERS
+	  "memory");
 
 	return error ? -ret : ret;
 }
@@ -83,7 +93,9 @@ static __always_inline int clock_getres_fallback(
 	: "=r" (ret), "=r" (error)
 	: "r" (clkid), "r" (ts), "r" (nr)
 	: "$1", "$3", "$8", "$9", "$10", "$11", "$12", "$13",
-	  "$14", "$15", "$24", "$25", "hi", "lo", "memory");
+	  "$14", "$15", "$24", "$25",
+	  VDSO_SYSCALL_CLOBBERS
+	  "memory");
 
 	return error ? -ret : ret;
 }
@@ -105,7 +117,9 @@ static __always_inline long clock_gettime32_fallback(
 	: "=r" (ret), "=r" (error)
 	: "r" (clkid), "r" (ts), "r" (nr)
 	: "$1", "$3", "$8", "$9", "$10", "$11", "$12", "$13",
-	  "$14", "$15", "$24", "$25", "hi", "lo", "memory");
+	  "$14", "$15", "$24", "$25",
+	  VDSO_SYSCALL_CLOBBERS
+	  "memory");
 
 	return error ? -ret : ret;
 }
@@ -125,7 +139,9 @@ static __always_inline int clock_getres32_fallback(
 	: "=r" (ret), "=r" (error)
 	: "r" (clkid), "r" (ts), "r" (nr)
 	: "$1", "$3", "$8", "$9", "$10", "$11", "$12", "$13",
-	  "$14", "$15", "$24", "$25", "hi", "lo", "memory");
+	  "$14", "$15", "$24", "$25",
+	  VDSO_SYSCALL_CLOBBERS
+	  "memory");
 
 	return error ? -ret : ret;
 }

arch/mips/kernel/Makefile

@@ -17,10 +17,10 @@ obj-y		+= cpu-probe.o
 endif
 
 ifdef CONFIG_FUNCTION_TRACER
-CFLAGS_REMOVE_ftrace.o = -pg
-CFLAGS_REMOVE_early_printk.o = -pg
-CFLAGS_REMOVE_perf_event.o = -pg
-CFLAGS_REMOVE_perf_event_mipsxx.o = -pg
+CFLAGS_REMOVE_ftrace.o = $(CC_FLAGS_FTRACE)
+CFLAGS_REMOVE_early_printk.o =  $(CC_FLAGS_FTRACE)
+CFLAGS_REMOVE_perf_event.o = $(CC_FLAGS_FTRACE)
+CFLAGS_REMOVE_perf_event_mipsxx.o = $(CC_FLAGS_FTRACE)
 endif
 
 obj-$(CONFIG_CEVT_BCM1480)	+= cevt-bcm1480.o

arch/mips/kernel/access-helper.h

+/* SPDX-License-Identifier: GPL-2.0 */
+
+#include <linux/uaccess.h>
+
+static inline int __get_addr(unsigned long *a, unsigned long *p, bool user)
+{
+	return user ? get_user(*a, (unsigned long __user *)p) :
+		      get_kernel_nofault(*a, p);
+}
+
+static inline int __get_inst16(u16 *i, u16 *p, bool user)
+{
+	return user ? get_user(*i, (u16 __user *)p) : get_kernel_nofault(*i, p);
+}
+
+static inline int __get_inst32(u32 *i, u32 *p, bool user)
+{
+	return user ? get_user(*i, (u32 __user *)p) : get_kernel_nofault(*i, p);
+}

arch/mips/kernel/asm-offsets.c

@@ -98,7 +98,6 @@ void output_thread_info_defines(void)
 	OFFSET(TI_TP_VALUE, thread_info, tp_value);
 	OFFSET(TI_CPU, thread_info, cpu);
 	OFFSET(TI_PRE_COUNT, thread_info, preempt_count);
-	OFFSET(TI_ADDR_LIMIT, thread_info, addr_limit);
 	OFFSET(TI_REGS, thread_info, regs);
 	DEFINE(_THREAD_SIZE, THREAD_SIZE);
 	DEFINE(_THREAD_MASK, THREAD_MASK);

arch/mips/kernel/cevt-r4k.c

@@ -195,10 +195,6 @@ int c0_compare_int_usable(void)
 	unsigned int delta;
 	unsigned int cnt;
 
-#ifdef CONFIG_KVM_GUEST
-    return 1;
-#endif
-
 	/*
 	 * IP7 already pending?	 Try to clear it by acking the timer.
 	 */

arch/mips/kernel/cpu-probe.c

@@ -1752,7 +1752,6 @@ static inline void cpu_probe_loongson(struct cpuinfo_mips *c, unsigned int cpu)
 			set_isa(c, MIPS_CPU_ISA_M64R2);
 			break;
 		}
-		c->writecombine = _CACHE_UNCACHED_ACCELERATED;
 		c->ases |= (MIPS_ASE_LOONGSON_MMI | MIPS_ASE_LOONGSON_EXT |
 				MIPS_ASE_LOONGSON_EXT2);
 		break;
@@ -1782,7 +1781,6 @@ static inline void cpu_probe_loongson(struct cpuinfo_mips *c, unsigned int cpu)
 		 * register, we correct it here.
 		 */
 		c->options |= MIPS_CPU_FTLB | MIPS_CPU_TLBINV | MIPS_CPU_LDPTE;
-		c->writecombine = _CACHE_UNCACHED_ACCELERATED;
 		c->ases |= (MIPS_ASE_LOONGSON_MMI | MIPS_ASE_LOONGSON_CAM |
 			MIPS_ASE_LOONGSON_EXT | MIPS_ASE_LOONGSON_EXT2);
 		c->ases &= ~MIPS_ASE_VZ; /* VZ of Loongson-3A2000/3000 is incomplete */
@@ -1793,7 +1791,6 @@ static inline void cpu_probe_loongson(struct cpuinfo_mips *c, unsigned int cpu)
 		set_elf_platform(cpu, "loongson3a");
 		set_isa(c, MIPS_CPU_ISA_M64R2);
 		decode_cpucfg(c);
-		c->writecombine = _CACHE_UNCACHED_ACCELERATED;
 		break;
 	default:
 		panic("Unknown Loongson Processor ID!");

arch/mips/kernel/ftrace.c

@@ -90,7 +90,6 @@ static int ftrace_modify_code_2(unsigned long ip, unsigned int new_code1,
 				unsigned int new_code2)
 {
 	int faulted;
-	mm_segment_t old_fs;
 
 	safe_store_code(new_code1, ip, faulted);
 	if (unlikely(faulted))
@@ -102,10 +101,7 @@ static int ftrace_modify_code_2(unsigned long ip, unsigned int new_code1,
 		return -EFAULT;
 
 	ip -= 4;
-	old_fs = get_fs();
-	set_fs(KERNEL_DS);
 	flush_icache_range(ip, ip + 8);
-	set_fs(old_fs);
 
 	return 0;
 }
@@ -114,7 +110,6 @@ static int ftrace_modify_code_2r(unsigned long ip, unsigned int new_code1,
 				 unsigned int new_code2)
 {
 	int faulted;
-	mm_segment_t old_fs;
 
 	ip += 4;
 	safe_store_code(new_code2, ip, faulted);
@@ -126,10 +121,7 @@ static int ftrace_modify_code_2r(unsigned long ip, unsigned int new_code1,
 	if (unlikely(faulted))
 		return -EFAULT;
 
-	old_fs = get_fs();
-	set_fs(KERNEL_DS);
 	flush_icache_range(ip, ip + 8);
-	set_fs(old_fs);
 
 	return 0;
 }

arch/mips/kernel/process.c

@@ -124,7 +124,6 @@ int copy_thread(unsigned long clone_flags, unsigned long usp,
 		/* kernel thread */
 		unsigned long status = p->thread.cp0_status;
 		memset(childregs, 0, sizeof(struct pt_regs));
-		ti->addr_limit = KERNEL_DS;
 		p->thread.reg16 = usp; /* fn */
 		p->thread.reg17 = kthread_arg;
 		p->thread.reg29 = childksp;
@@ -145,7 +144,6 @@ int copy_thread(unsigned long clone_flags, unsigned long usp,
 	childregs->regs[2] = 0; /* Child gets zero as return value */
 	if (usp)
 		childregs->regs[29] = usp;
-	ti->addr_limit = USER_DS;
 
 	p->thread.reg29 = (unsigned long) childregs;
 	p->thread.reg31 = (unsigned long) ret_from_fork;

arch/mips/kernel/relocate_kernel.S

@@ -11,6 +11,8 @@
 #include <asm/stackframe.h>
 #include <asm/addrspace.h>
 
+#include <kernel-entry-init.h>
+
 LEAF(relocate_new_kernel)
 	PTR_L a0,	arg0
 	PTR_L a1,	arg1
@@ -125,11 +127,8 @@ LEAF(kexec_smp_wait)
 1:	LONG_L		s0, (t0)
 	bne		s0, zero,1b
 
-#ifdef CONFIG_CPU_CAVIUM_OCTEON
-	.set push
-	.set noreorder
-	synci		0($0)
-	.set pop
+#ifdef USE_KEXEC_SMP_WAIT_FINAL
+	kexec_smp_wait_final
 #else
 	sync
 #endif

arch/mips/kernel/scall32-o32.S

@@ -48,10 +48,8 @@ NESTED(handle_sys, PT_SIZE, sp)
 	 * We intentionally keep the kernel stack a little below the top of
 	 * userspace so we don't have to do a slower byte accurate check here.
 	 */
-	lw	t5, TI_ADDR_LIMIT($28)
 	addu	t4, t0, 32
-	and	t5, t4
-	bltz	t5, bad_stack		# -> sp is bad
+	bltz	t4, bad_stack		# -> sp is bad
 
 	/*
 	 * Ok, copy the args from the luser stack to the kernel stack.
@@ -217,9 +215,9 @@ einval: li	v0, -ENOSYS
 #define sys_sched_getaffinity	mipsmt_sys_sched_getaffinity
 #endif /* CONFIG_MIPS_MT_FPAFF */
 
+#define __SYSCALL_WITH_COMPAT(nr, native, compat)	__SYSCALL(nr, native)
 #define __SYSCALL(nr, entry) 	PTR entry
 	.align	2
 	.type	sys_call_table, @object
 EXPORT(sys_call_table)
-#include <asm/syscall_table_32_o32.h>
-#undef __SYSCALL
+#include <asm/syscall_table_o32.h>

arch/mips/kernel/scall64-n32.S

@@ -104,5 +104,4 @@ not_n32_scall:
 #define __SYSCALL(nr, entry)	PTR entry
 	.type	sysn32_call_table, @object
 EXPORT(sysn32_call_table)
-#include <asm/syscall_table_64_n32.h>
-#undef __SYSCALL
+#include <asm/syscall_table_n32.h>

arch/mips/kernel/scall64-n64.S

@@ -113,5 +113,4 @@ illegal_syscall:
 	.align	3
 	.type	sys_call_table, @object
 EXPORT(sys_call_table)
-#include <asm/syscall_table_64_n64.h>
-#undef __SYSCALL
+#include <asm/syscall_table_n64.h>

arch/mips/kernel/scall64-o32.S

@@ -213,9 +213,9 @@ einval: li	v0, -ENOSYS
 	jr	ra
 	END(sys32_syscall)
 
+#define __SYSCALL_WITH_COMPAT(nr, native, compat)	__SYSCALL(nr, compat)
 #define __SYSCALL(nr, entry)	PTR entry
 	.align	3
 	.type	sys32_call_table,@object
 EXPORT(sys32_call_table)
-#include <asm/syscall_table_64_o32.h>
-#undef __SYSCALL
+#include <asm/syscall_table_o32.h>

arch/mips/kernel/smp-bmips.c

@@ -134,17 +134,24 @@ static void __init bmips_smp_setup(void)
 	if (!board_ebase_setup)
 		board_ebase_setup = &bmips_ebase_setup;
 
-	__cpu_number_map[boot_cpu] = 0;
-	__cpu_logical_map[0] = boot_cpu;
-
-	for (i = 0; i < max_cpus; i++) {
-		if (i != boot_cpu) {
-			__cpu_number_map[i] = cpu;
-			__cpu_logical_map[cpu] = i;
-			cpu++;
+	if (max_cpus > 1) {
+		__cpu_number_map[boot_cpu] = 0;
+		__cpu_logical_map[0] = boot_cpu;
+
+		for (i = 0; i < max_cpus; i++) {
+			if (i != boot_cpu) {
+				__cpu_number_map[i] = cpu;
+				__cpu_logical_map[cpu] = i;
+				cpu++;
+			}
+			set_cpu_possible(i, 1);
+			set_cpu_present(i, 1);
 		}
-		set_cpu_possible(i, 1);
-		set_cpu_present(i, 1);
+	} else {
+		__cpu_number_map[0] = boot_cpu;
+		__cpu_logical_map[0] = 0;
+		set_cpu_possible(0, 1);
+		set_cpu_present(0, 1);
 	}
 }
 

arch/mips/kernel/spinlock_test.c

@@ -35,7 +35,7 @@ static int ss_get(void *data, u64 *val)
 	return 0;
 }
 
-DEFINE_SIMPLE_ATTRIBUTE(fops_ss, ss_get, NULL, "%llu\n");
+DEFINE_DEBUGFS_ATTRIBUTE(fops_ss, ss_get, NULL, "%llu\n");
 
 
 
@@ -114,13 +114,13 @@ static int multi_get(void *data, u64 *val)
 	return 0;
 }
 
-DEFINE_SIMPLE_ATTRIBUTE(fops_multi, multi_get, NULL, "%llu\n");
+DEFINE_DEBUGFS_ATTRIBUTE(fops_multi, multi_get, NULL, "%llu\n");
 
 static int __init spinlock_test(void)
 {
-	debugfs_create_file("spin_single", S_IRUGO, mips_debugfs_dir, NULL,
+	debugfs_create_file_unsafe("spin_single", S_IRUGO, mips_debugfs_dir, NULL,
 			    &fops_ss);
-	debugfs_create_file("spin_multi", S_IRUGO, mips_debugfs_dir, NULL,
+	debugfs_create_file_unsafe("spin_multi", S_IRUGO, mips_debugfs_dir, NULL,
 			    &fops_multi);
 	return 0;
 }

arch/mips/kernel/syscalls/Makefile

@@ -8,15 +8,12 @@ _dummy := $(shell [ -d '$(uapi)' ] || mkdir -p '$(uapi)')	\
 syscalln32 := $(src)/syscall_n32.tbl
 syscalln64 := $(src)/syscall_n64.tbl
 syscallo32 := $(src)/syscall_o32.tbl
-syshdr := $(srctree)/$(src)/syscallhdr.sh
+syshdr := $(srctree)/scripts/syscallhdr.sh
 sysnr := $(srctree)/$(src)/syscallnr.sh
-systbl := $(srctree)/$(src)/syscalltbl.sh
+systbl := $(srctree)/scripts/syscalltbl.sh
 
 quiet_cmd_syshdr = SYSHDR  $@
-      cmd_syshdr = $(CONFIG_SHELL) '$(syshdr)' '$<' '$@'	\
-		   '$(syshdr_abis_$(basetarget))'		\
-		   '$(syshdr_pfx_$(basetarget))'		\
-		   '$(syshdr_offset_$(basetarget))'
+      cmd_syshdr = $(CONFIG_SHELL) $(syshdr) --offset __NR_Linux $< $@
 
 quiet_cmd_sysnr = SYSNR   $@
       cmd_sysnr = $(CONFIG_SHELL) '$(sysnr)' '$<' '$@'		\
@@ -25,20 +22,14 @@ quiet_cmd_sysnr = SYSNR   $@
 		  '$(sysnr_offset_$(basetarget))'
 
 quiet_cmd_systbl = SYSTBL  $@
-      cmd_systbl = $(CONFIG_SHELL) '$(systbl)' '$<' '$@'	\
-		   '$(systbl_abis_$(basetarget))'		\
-		   '$(systbl_abi_$(basetarget))'		\
-		   '$(systbl_offset_$(basetarget))'
+      cmd_systbl = $(CONFIG_SHELL) $(systbl) $< $@
 
-syshdr_offset_unistd_n32 := __NR_Linux
 $(uapi)/unistd_n32.h: $(syscalln32) $(syshdr) FORCE
 	$(call if_changed,syshdr)
 
-syshdr_offset_unistd_n64 := __NR_Linux
 $(uapi)/unistd_n64.h: $(syscalln64) $(syshdr) FORCE
 	$(call if_changed,syshdr)
 
-syshdr_offset_unistd_o32 := __NR_Linux
 $(uapi)/unistd_o32.h: $(syscallo32) $(syshdr) FORCE
 	$(call if_changed,syshdr)
 
@@ -57,33 +48,21 @@ sysnr_offset_unistd_nr_o32 := 4000
 $(kapi)/unistd_nr_o32.h: $(syscallo32) $(sysnr) FORCE
 	$(call if_changed,sysnr)
 
-systbl_abi_syscall_table_32_o32 := 32_o32
-systbl_offset_syscall_table_32_o32 := 4000
-$(kapi)/syscall_table_32_o32.h: $(syscallo32) $(systbl) FORCE
+$(kapi)/syscall_table_n32.h: $(syscalln32) $(systbl) FORCE
 	$(call if_changed,systbl)
 
-systbl_abi_syscall_table_64_n32 := 64_n32
-systbl_offset_syscall_table_64_n32 := 6000
-$(kapi)/syscall_table_64_n32.h: $(syscalln32) $(systbl) FORCE
+$(kapi)/syscall_table_n64.h: $(syscalln64) $(systbl) FORCE
 	$(call if_changed,systbl)
 
-systbl_abi_syscall_table_64_n64 := 64_n64
-systbl_offset_syscall_table_64_n64 := 5000
-$(kapi)/syscall_table_64_n64.h: $(syscalln64) $(systbl) FORCE
-	$(call if_changed,systbl)
-
-systbl_abi_syscall_table_64_o32 := 64_o32
-systbl_offset_syscall_table_64_o32 := 4000
-$(kapi)/syscall_table_64_o32.h: $(syscallo32) $(systbl) FORCE
+$(kapi)/syscall_table_o32.h: $(syscallo32) $(systbl) FORCE
 	$(call if_changed,systbl)
 
 uapisyshdr-y		+= unistd_n32.h			\
 			   unistd_n64.h			\
 			   unistd_o32.h
-kapisyshdr-y		+= syscall_table_32_o32.h	\
-			   syscall_table_64_n32.h	\
-			   syscall_table_64_n64.h	\
-			   syscall_table_64_o32.h	\
+kapisyshdr-y		+= syscall_table_n32.h		\
+			   syscall_table_n64.h		\
+			   syscall_table_o32.h		\
 			   unistd_nr_n32.h		\
 			   unistd_nr_n64.h		\
 			   unistd_nr_o32.h

arch/mips/kernel/syscalls/syscallhdr.sh

-#!/bin/sh
-# SPDX-License-Identifier: GPL-2.0
-
-in="$1"
-out="$2"
-my_abis=`echo "($3)" | tr ',' '|'`
-prefix="$4"
-offset="$5"
-
-fileguard=_UAPI_ASM_MIPS_`basename "$out" | sed \
-	-e 'y/abcdefghijklmnopqrstuvwxyz/ABCDEFGHIJKLMNOPQRSTUVWXYZ/' \
-	-e 's/[^A-Z0-9_]/_/g' -e 's/__/_/g'`
-grep -E "^[0-9A-Fa-fXx]+[[:space:]]+${my_abis}" "$in" | sort -n | (
-	printf "#ifndef %s\n" "${fileguard}"
-	printf "#define %s\n" "${fileguard}"
-	printf "\n"
-
-	nxt=0
-	while read nr abi name entry compat ; do
-		if [ -z "$offset" ]; then
-			printf "#define __NR_%s%s\t%s\n" \
-				"${prefix}" "${name}" "${nr}"
-		else
-			printf "#define __NR_%s%s\t(%s + %s)\n" \
-				"${prefix}" "${name}" "${offset}" "${nr}"
-		fi
-		nxt=$((nr+1))
-	done
-
-	printf "\n"
-	printf "#ifdef __KERNEL__\n"
-	printf "#define __NR_syscalls\t%s\n" "${nxt}"
-	printf "#endif\n"
-	printf "\n"
-	printf "#endif /* %s */\n" "${fileguard}"
-) > "$out"

arch/mips/kernel/syscalls/syscalltbl.sh

-#!/bin/sh
-# SPDX-License-Identifier: GPL-2.0
-
-in="$1"
-out="$2"
-my_abis=`echo "($3)" | tr ',' '|'`
-my_abi="$4"
-offset="$5"
-
-emit() {
-	t_nxt="$1"
-	t_nr="$2"
-	t_entry="$3"
-
-	while [ $t_nxt -lt $t_nr ]; do
-		printf "__SYSCALL(%s,sys_ni_syscall)\n" "${t_nxt}"
-		t_nxt=$((t_nxt+1))
-	done
-	printf "__SYSCALL(%s,%s)\n" "${t_nxt}" "${t_entry}"
-}
-
-grep -E "^[0-9A-Fa-fXx]+[[:space:]]+${my_abis}" "$in" | sort -n | (
-	nxt=0
-	if [ -z "$offset" ]; then
-		offset=0
-	fi
-
-	while read nr abi name entry compat ; do
-		if [ "$my_abi" = "64_o32" ] && [ ! -z "$compat" ]; then
-			emit $((nxt+offset)) $((nr+offset)) $compat
-		else
-			emit $((nxt+offset)) $((nr+offset)) $entry
-		fi
-		nxt=$((nr+1))
-	done
-) > "$out"

arch/mips/kernel/vdso.c

@@ -90,7 +90,7 @@ int arch_setup_additional_pages(struct linux_binprm *bprm, int uses_interp)
 {
 	struct mips_vdso_image *image = current->thread.abi->vdso;
 	struct mm_struct *mm = current->mm;
-	unsigned long gic_size, vvar_size, size, base, data_addr, vdso_addr, gic_pfn;
+	unsigned long gic_size, vvar_size, size, base, data_addr, vdso_addr, gic_pfn, gic_base;
 	struct vm_area_struct *vma;
 	int ret;
 
@@ -158,7 +158,8 @@ int arch_setup_additional_pages(struct linux_binprm *bprm, int uses_interp)
 
 	/* Map GIC user page. */
 	if (gic_size) {
-		gic_pfn = virt_to_phys(mips_gic_base + MIPS_GIC_USER_OFS) >> PAGE_SHIFT;
+		gic_base = (unsigned long)mips_gic_base + MIPS_GIC_USER_OFS;
+		gic_pfn = virt_to_phys((void *)gic_base) >> PAGE_SHIFT;
 
 		ret = io_remap_pfn_range(vma, base, gic_pfn, gic_size,
 					 pgprot_noncached(vma->vm_page_prot));

arch/mips/kvm/Kconfig

@@ -30,40 +30,6 @@ config KVM
 	help
 	  Support for hosting Guest kernels.
 
-choice
-	prompt "Virtualization mode"
-	depends on KVM
-	default KVM_MIPS_TE
-
-config KVM_MIPS_TE
-	bool "Trap & Emulate"
-	depends on CPU_MIPS32_R2
-	help
-	  Use trap and emulate to virtualize 32-bit guests in user mode. This
-	  does not require any special hardware Virtualization support beyond
-	  standard MIPS32 r2 or later, but it does require the guest kernel
-	  to be configured with CONFIG_KVM_GUEST=y so that it resides in the
-	  user address segment.
-
-config KVM_MIPS_VZ
-	bool "MIPS Virtualization (VZ) ASE"
-	help
-	  Use the MIPS Virtualization (VZ) ASE to virtualize guests. This
-	  supports running unmodified guest kernels (with CONFIG_KVM_GUEST=n),
-	  but requires hardware support.
-
-endchoice
-
-config KVM_MIPS_DYN_TRANS
-	bool "KVM/MIPS: Dynamic binary translation to reduce traps"
-	depends on KVM_MIPS_TE
-	default y
-	help
-	  When running in Trap & Emulate mode patch privileged
-	  instructions to reduce the number of traps.
-
-	  If unsure, say Y.
-
 config KVM_MIPS_DEBUG_COP0_COUNTERS
 	bool "Maintain counters for COP0 accesses"
 	depends on KVM

arch/mips/kvm/Makefile

@@ -9,7 +9,7 @@ EXTRA_CFLAGS += -Ivirt/kvm -Iarch/mips/kvm
 common-objs-$(CONFIG_CPU_HAS_MSA) += msa.o
 
 kvm-objs := $(common-objs-y) mips.o emulate.o entry.o \
-	    interrupt.o stats.o commpage.o \
+	    interrupt.o stats.o \
 	    fpu.o
 kvm-objs += hypcall.o
 kvm-objs += mmu.o
@@ -17,11 +17,6 @@ ifdef CONFIG_CPU_LOONGSON64
 kvm-objs += loongson_ipi.o
 endif
 
-ifdef CONFIG_KVM_MIPS_VZ
 kvm-objs		+= vz.o
-else
-kvm-objs		+= dyntrans.o
-kvm-objs		+= trap_emul.o
-endif
 obj-$(CONFIG_KVM)	+= kvm.o
 obj-y			+= callback.o tlb.o

arch/mips/kvm/commpage.c

-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * commpage, currently used for Virtual COP0 registers.
- * Mapped into the guest kernel @ KVM_GUEST_COMMPAGE_ADDR.
- *
- * Copyright (C) 2012  MIPS Technologies, Inc.  All rights reserved.
- * Authors: Sanjay Lal <sanjayl@kymasys.com>
- */
-
-#include <linux/errno.h>
-#include <linux/err.h>
-#include <linux/vmalloc.h>
-#include <linux/fs.h>
-#include <linux/memblock.h>
-#include <asm/page.h>
-#include <asm/cacheflush.h>
-#include <asm/mmu_context.h>
-
-#include <linux/kvm_host.h>
-
-#include "commpage.h"
-
-void kvm_mips_commpage_init(struct kvm_vcpu *vcpu)
-{
-	struct kvm_mips_commpage *page = vcpu->arch.kseg0_commpage;
-
-	/* Specific init values for fields */
-	vcpu->arch.cop0 = &page->cop0;
-}