Merge tag 'usb-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB fixes from Greg KH:
 "Here are a few small USB driver fixes for 4.10-rc4 to resolve some
  reported issues.

  The "largest" here is a number of bugs being fixed in the ch341
  usb-serial driver, to hopefully resolve the mess of different devices
  floating around that use this driver that have been having problems
  with the 4.10-rc1 release.

  There's also a tiny musb fix that I missed in the last pull request,
  as well as the traditional xhci fix rounding out the batch.

  All have been in linux-next with no reported issues"

* tag 'usb-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  xhci: fix deadlock at host remove by running watchdog correctly
  USB: serial: ch341: fix control-message error handling
  usb: musb: fix runtime PM in debugfs
  wusbcore: Fix one more crypto-on-the-stack bug
  USB: serial: kl5kusb105: fix line-state error handling
  USB: serial: ch341: fix baud rate and line-control handling
  USB: serial: ch341: fix line settings after reset-resume
  USB: serial: ch341: fix resume after reset
  USB: serial: ch341: fix open error handling
  USB: serial: ch341: fix modem-control and B0 handling
  USB: serial: ch341: fix open and resume after B0
  USB: serial: ch341: fix initial modem-control state

drivers/usb/host/xhci-ring.c

@@ -913,17 +913,6 @@ void xhci_stop_endpoint_command_watchdog(unsigned long arg)
 	spin_lock_irqsave(&xhci->lock, flags);
 
 	ep->stop_cmds_pending--;
-	if (xhci->xhc_state & XHCI_STATE_REMOVING) {
-		spin_unlock_irqrestore(&xhci->lock, flags);
-		return;
-	}
-	if (xhci->xhc_state & XHCI_STATE_DYING) {
-		xhci_dbg_trace(xhci, trace_xhci_dbg_cancel_urb,
-				"Stop EP timer ran, but another timer marked "
-				"xHCI as DYING, exiting.");
-		spin_unlock_irqrestore(&xhci->lock, flags);
-		return;
-	}
 	if (!(ep->stop_cmds_pending == 0 && (ep->ep_state & EP_HALT_PENDING))) {
 		xhci_dbg_trace(xhci, trace_xhci_dbg_cancel_urb,
 				"Stop EP timer ran, but no command pending, "

drivers/usb/host/xhci.c

@@ -1534,19 +1534,6 @@ int xhci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status)
 		xhci_urb_free_priv(urb_priv);
 		return ret;
 	}
-	if ((xhci->xhc_state & XHCI_STATE_DYING) ||
-			(xhci->xhc_state & XHCI_STATE_HALTED)) {
-		xhci_dbg_trace(xhci, trace_xhci_dbg_cancel_urb,
-				"Ep 0x%x: URB %p to be canceled on "
-				"non-responsive xHCI host.",
-				urb->ep->desc.bEndpointAddress, urb);
-		/* Let the stop endpoint command watchdog timer (which set this
-		 * state) finish cleaning up the endpoint TD lists.  We must
-		 * have caught it in the middle of dropping a lock and giving
-		 * back an URB.
-		 */
-		goto done;
-	}
 
 	ep_index = xhci_get_endpoint_index(&urb->ep->desc);
 	ep = &xhci->devs[urb->dev->slot_id]->eps[ep_index];

drivers/usb/musb/musb_debugfs.c

@@ -114,6 +114,7 @@ static int musb_regdump_show(struct seq_file *s, void *unused)
 	unsigned		i;
 
 	seq_printf(s, "MUSB (M)HDRC Register Dump\n");
+	pm_runtime_get_sync(musb->controller);
 
 	for (i = 0; i < ARRAY_SIZE(musb_regmap); i++) {
 		switch (musb_regmap[i].size) {
@@ -132,6 +133,8 @@ static int musb_regdump_show(struct seq_file *s, void *unused)
 		}
 	}
 
+	pm_runtime_mark_last_busy(musb->controller);
+	pm_runtime_put_autosuspend(musb->controller);
 	return 0;
 }
 
@@ -145,7 +148,10 @@ static int musb_test_mode_show(struct seq_file *s, void *unused)
 	struct musb		*musb = s->private;
 	unsigned		test;
 
+	pm_runtime_get_sync(musb->controller);
 	test = musb_readb(musb->mregs, MUSB_TESTMODE);
+	pm_runtime_mark_last_busy(musb->controller);
+	pm_runtime_put_autosuspend(musb->controller);
 
 	if (test & MUSB_TEST_FORCE_HOST)
 		seq_printf(s, "force host\n");
@@ -194,11 +200,12 @@ static ssize_t musb_test_mode_write(struct file *file,
 	u8			test;
 	char			buf[18];
 
+	pm_runtime_get_sync(musb->controller);
 	test = musb_readb(musb->mregs, MUSB_TESTMODE);
 	if (test) {
 		dev_err(musb->controller, "Error: test mode is already set. "
 			"Please do USB Bus Reset to start a new test.\n");
-		return count;
+		goto ret;
 	}
 
 	memset(buf, 0x00, sizeof(buf));
@@ -234,6 +241,9 @@ static ssize_t musb_test_mode_write(struct file *file,
 
 	musb_writeb(musb->mregs, MUSB_TESTMODE, test);
 
+ret:
+	pm_runtime_mark_last_busy(musb->controller);
+	pm_runtime_put_autosuspend(musb->controller);
 	return count;
 }
 
@@ -254,8 +264,13 @@ static int musb_softconnect_show(struct seq_file *s, void *unused)
 	switch (musb->xceiv->otg->state) {
 	case OTG_STATE_A_HOST:
 	case OTG_STATE_A_WAIT_BCON:
+		pm_runtime_get_sync(musb->controller);
+
 		reg = musb_readb(musb->mregs, MUSB_DEVCTL);
 		connect = reg & MUSB_DEVCTL_SESSION ? 1 : 0;
+
+		pm_runtime_mark_last_busy(musb->controller);
+		pm_runtime_put_autosuspend(musb->controller);
 		break;
 	default:
 		connect = -1;
@@ -284,6 +299,7 @@ static ssize_t musb_softconnect_write(struct file *file,
 	if (copy_from_user(&buf, ubuf, min_t(size_t, sizeof(buf) - 1, count)))
 		return -EFAULT;
 
+	pm_runtime_get_sync(musb->controller);
 	if (!strncmp(buf, "0", 1)) {
 		switch (musb->xceiv->otg->state) {
 		case OTG_STATE_A_HOST:
@@ -314,6 +330,8 @@ static ssize_t musb_softconnect_write(struct file *file,
 		}
 	}
 
+	pm_runtime_mark_last_busy(musb->controller);
+	pm_runtime_put_autosuspend(musb->controller);
 	return count;
 }
 

drivers/usb/serial/ch341.c

@@ -95,6 +95,7 @@ struct ch341_private {
 	unsigned baud_rate; /* set baud rate */
 	u8 line_control; /* set line control value RTS/DTR */
 	u8 line_status; /* active status of modem control inputs */
+	u8 lcr;
 };
 
 static void ch341_set_termios(struct tty_struct *tty,
@@ -112,6 +113,8 @@ static int ch341_control_out(struct usb_device *dev, u8 request,
 	r = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), request,
 			    USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
 			    value, index, NULL, 0, DEFAULT_TIMEOUT);
+	if (r < 0)
+		dev_err(&dev->dev, "failed to send control message: %d\n", r);
 
 	return r;
 }
@@ -129,11 +132,24 @@ static int ch341_control_in(struct usb_device *dev,
 	r = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), request,
 			    USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
 			    value, index, buf, bufsize, DEFAULT_TIMEOUT);
-	return r;
+	if (r < bufsize) {
+		if (r >= 0) {
+			dev_err(&dev->dev,
+				"short control message received (%d < %u)\n",
+				r, bufsize);
+			r = -EIO;
+		}
+
+		dev_err(&dev->dev, "failed to receive control message: %d\n",
+			r);
+		return r;
+	}
+
+	return 0;
 }
 
-static int ch341_init_set_baudrate(struct usb_device *dev,
-				   struct ch341_private *priv, unsigned ctrl)
+static int ch341_set_baudrate_lcr(struct usb_device *dev,
+				  struct ch341_private *priv, u8 lcr)
 {
 	short a;
 	int r;
@@ -156,9 +172,19 @@ static int ch341_init_set_baudrate(struct usb_device *dev,
 	factor = 0x10000 - factor;
 	a = (factor & 0xff00) | divisor;
 
-	/* 0x9c is "enable SFR_UART Control register and timer" */
-	r = ch341_control_out(dev, CH341_REQ_SERIAL_INIT,
-			      0x9c | (ctrl << 8), a | 0x80);
+	/*
+	 * CH341A buffers data until a full endpoint-size packet (32 bytes)
+	 * has been received unless bit 7 is set.
+	 */
+	a |= BIT(7);
+
+	r = ch341_control_out(dev, CH341_REQ_WRITE_REG, 0x1312, a);
+	if (r)
+		return r;
+
+	r = ch341_control_out(dev, CH341_REQ_WRITE_REG, 0x2518, lcr);
+	if (r)
+		return r;
 
 	return r;
 }
@@ -170,9 +196,9 @@ static int ch341_set_handshake(struct usb_device *dev, u8 control)
 
 static int ch341_get_status(struct usb_device *dev, struct ch341_private *priv)
 {
+	const unsigned int size = 2;
 	char *buffer;
 	int r;
-	const unsigned size = 8;
 	unsigned long flags;
 
 	buffer = kmalloc(size, GFP_KERNEL);
@@ -183,14 +209,9 @@ static int ch341_get_status(struct usb_device *dev, struct ch341_private *priv)
 	if (r < 0)
 		goto out;
 
-	/* setup the private status if available */
-	if (r == 2) {
-		r = 0;
-		spin_lock_irqsave(&priv->lock, flags);
-		priv->line_status = (~(*buffer)) & CH341_BITS_MODEM_STAT;
-		spin_unlock_irqrestore(&priv->lock, flags);
-	} else
-		r = -EPROTO;
+	spin_lock_irqsave(&priv->lock, flags);
+	priv->line_status = (~(*buffer)) & CH341_BITS_MODEM_STAT;
+	spin_unlock_irqrestore(&priv->lock, flags);
 
 out:	kfree(buffer);
 	return r;
@@ -200,9 +221,9 @@ out:	kfree(buffer);
 
 static int ch341_configure(struct usb_device *dev, struct ch341_private *priv)
 {
+	const unsigned int size = 2;
 	char *buffer;
 	int r;
-	const unsigned size = 8;
 
 	buffer = kmalloc(size, GFP_KERNEL);
 	if (!buffer)
@@ -232,7 +253,7 @@ static int ch341_configure(struct usb_device *dev, struct ch341_private *priv)
 	if (r < 0)
 		goto out;
 
-	r = ch341_init_set_baudrate(dev, priv, 0);
+	r = ch341_set_baudrate_lcr(dev, priv, priv->lcr);
 	if (r < 0)
 		goto out;
 
@@ -258,7 +279,6 @@ static int ch341_port_probe(struct usb_serial_port *port)
 
 	spin_lock_init(&priv->lock);
 	priv->baud_rate = DEFAULT_BAUD_RATE;
-	priv->line_control = CH341_BIT_RTS | CH341_BIT_DTR;
 
 	r = ch341_configure(port->serial->dev, priv);
 	if (r < 0)
@@ -320,7 +340,7 @@ static int ch341_open(struct tty_struct *tty, struct usb_serial_port *port)
 
 	r = ch341_configure(serial->dev, priv);
 	if (r)
-		goto out;
+		return r;
 
 	if (tty)
 		ch341_set_termios(tty, port, NULL);
@@ -330,12 +350,19 @@ static int ch341_open(struct tty_struct *tty, struct usb_serial_port *port)
 	if (r) {
 		dev_err(&port->dev, "%s - failed to submit interrupt urb: %d\n",
 			__func__, r);
-		goto out;
+		return r;
 	}
 
 	r = usb_serial_generic_open(tty, port);
+	if (r)
+		goto err_kill_interrupt_urb;
+
+	return 0;
+
+err_kill_interrupt_urb:
+	usb_kill_urb(port->interrupt_in_urb);
 
-out:	return r;
+	return r;
 }
 
 /* Old_termios contains the original termios settings and
@@ -356,7 +383,6 @@ static void ch341_set_termios(struct tty_struct *tty,
 
 	baud_rate = tty_get_baud_rate(tty);
 
-	priv->baud_rate = baud_rate;
 	ctrl = CH341_LCR_ENABLE_RX | CH341_LCR_ENABLE_TX;
 
 	switch (C_CSIZE(tty)) {
@@ -386,22 +412,25 @@ static void ch341_set_termios(struct tty_struct *tty,
 		ctrl |= CH341_LCR_STOP_BITS_2;
 
 	if (baud_rate) {
-		spin_lock_irqsave(&priv->lock, flags);
-		priv->line_control |= (CH341_BIT_DTR | CH341_BIT_RTS);
-		spin_unlock_irqrestore(&priv->lock, flags);
-		r = ch341_init_set_baudrate(port->serial->dev, priv, ctrl);
+		priv->baud_rate = baud_rate;
+
+		r = ch341_set_baudrate_lcr(port->serial->dev, priv, ctrl);
 		if (r < 0 && old_termios) {
 			priv->baud_rate = tty_termios_baud_rate(old_termios);
 			tty_termios_copy_hw(&tty->termios, old_termios);
+		} else if (r == 0) {
+			priv->lcr = ctrl;
 		}
-	} else {
-		spin_lock_irqsave(&priv->lock, flags);
-		priv->line_control &= ~(CH341_BIT_DTR | CH341_BIT_RTS);
-		spin_unlock_irqrestore(&priv->lock, flags);
 	}
 
-	ch341_set_handshake(port->serial->dev, priv->line_control);
+	spin_lock_irqsave(&priv->lock, flags);
+	if (C_BAUD(tty) == B0)
+		priv->line_control &= ~(CH341_BIT_DTR | CH341_BIT_RTS);
+	else if (old_termios && (old_termios->c_cflag & CBAUD) == B0)
+		priv->line_control |= (CH341_BIT_DTR | CH341_BIT_RTS);
+	spin_unlock_irqrestore(&priv->lock, flags);
 
+	ch341_set_handshake(port->serial->dev, priv->line_control);
 }
 
 static void ch341_break_ctl(struct tty_struct *tty, int break_state)
@@ -576,14 +605,23 @@ static int ch341_tiocmget(struct tty_struct *tty)
 
 static int ch341_reset_resume(struct usb_serial *serial)
 {
-	struct ch341_private *priv;
-
-	priv = usb_get_serial_port_data(serial->port[0]);
+	struct usb_serial_port *port = serial->port[0];
+	struct ch341_private *priv = usb_get_serial_port_data(port);
+	int ret;
 
 	/* reconfigure ch341 serial port after bus-reset */
 	ch341_configure(serial->dev, priv);
 
-	return 0;
+	if (tty_port_initialized(&port->port)) {
+		ret = usb_submit_urb(port->interrupt_in_urb, GFP_NOIO);
+		if (ret) {
+			dev_err(&port->dev, "failed to submit interrupt urb: %d\n",
+				ret);
+			return ret;
+		}
+	}
+
+	return usb_serial_generic_resume(serial);
 }
 
 static struct usb_serial_driver ch341_device = {

drivers/usb/serial/kl5kusb105.c

@@ -192,10 +192,11 @@ static int klsi_105_get_line_state(struct usb_serial_port *port,
 			     status_buf, KLSI_STATUSBUF_LEN,
 			     10000
 			     );
-	if (rc < 0)
-		dev_err(&port->dev, "Reading line status failed (error = %d)\n",
-			rc);
-	else {
+	if (rc != KLSI_STATUSBUF_LEN) {
+		dev_err(&port->dev, "reading line status failed: %d\n", rc);
+		if (rc >= 0)
+			rc = -EIO;
+	} else {
 		status = get_unaligned_le16(status_buf);
 
 		dev_info(&port->serial->dev->dev, "read status %x %x\n",

drivers/usb/wusbcore/crypto.c

@@ -216,7 +216,6 @@ static int wusb_ccm_mac(struct crypto_skcipher *tfm_cbc,
 	struct scatterlist sg[4], sg_dst;
 	void *dst_buf;
 	size_t dst_size;
-	const u8 bzero[16] = { 0 };
 	u8 iv[crypto_skcipher_ivsize(tfm_cbc)];
 	size_t zero_padding;
 
@@ -261,7 +260,7 @@ static int wusb_ccm_mac(struct crypto_skcipher *tfm_cbc,
 	sg_set_buf(&sg[1], &scratch->b1, sizeof(scratch->b1));
 	sg_set_buf(&sg[2], b, blen);
 	/* 0 if well behaved :) */
-	sg_set_buf(&sg[3], bzero, zero_padding);
+	sg_set_page(&sg[3], ZERO_PAGE(0), zero_padding, 0);
 	sg_init_one(&sg_dst, dst_buf, dst_size);
 
 	skcipher_request_set_tfm(req, tfm_cbc);