Merge branches 'pci/host-exynos', 'pci/host-rcar' and 'pci/amd-numa' into next

* pci/host-exynos:
  PCI: exynos: Remove unnecessary OOM messages

* pci/host-rcar:
  PCI: rcar: Add gen2 device tree support
  PCI: rcar: Add R-Car PCIe device tree bindings
  PCI: rcar: Add MSI support for PCIe
  PCI: rcar: Add Renesas R-Car PCIe driver
  PCI: rcar: Use new OF interrupt mapping when possible

* pci/amd-numa:
  x86/PCI: Clean up and mark early_root_info_init() as deprecated
  x86/PCI: Work around AMD Fam15h BIOSes that fail to provide _PXM
  x86/PCI: Warn if we have to "guess" host bridge node information

Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt

+Renesas AHB to PCI bridge
+-------------------------
+
+This is the bridge used internally to connect the USB controllers to the
+AHB. There is one bridge instance per USB port connected to the internal
+OHCI and EHCI controllers.
+
+Required properties:
+- compatible: "renesas,pci-r8a7790" for the R8A7790 SoC;
+	      "renesas,pci-r8a7791" for the R8A7791 SoC.
+- reg:	A list of physical regions to access the device: the first is
+	the operational registers for the OHCI/EHCI controllers and the
+	second is for the bridge configuration and control registers.
+- interrupts: interrupt for the device.
+- clocks: The reference to the device clock.
+- bus-range: The PCI bus number range; as this is a single bus, the range
+	     should be specified as the same value twice.
+- #address-cells: must be 3.
+- #size-cells: must be 2.
+- #interrupt-cells: must be 1.
+- interrupt-map: standard property used to define the mapping of the PCI
+  interrupts to the GIC interrupts.
+- interrupt-map-mask: standard property that helps to define the interrupt
+  mapping.
+
+Example SoC configuration:
+
+	pci0: pci@ee090000  {
+		compatible = "renesas,pci-r8a7790";
+		clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
+		reg = <0x0 0xee090000 0x0 0xc00>,
+		      <0x0 0xee080000 0x0 0x1100>;
+		interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>;
+		status = "disabled";
+
+		bus-range = <0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0xff00 0 0 0x7>;
+		interrupt-map = <0x0000 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH
+				 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH
+				 0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>;
+
+		pci@0,1 {
+			reg = <0x800 0 0 0 0>;
+			device_type = "pci";
+			phys = <&usbphy 0 0>;
+			phy-names = "usb";
+		};
+
+		pci@0,2 {
+			reg = <0x1000 0 0 0 0>;
+			device_type = "pci";
+			phys = <&usbphy 0 0>;
+			phy-names = "usb";
+		};
+	};
+
+Example board setup:
+
+&pci0 {
+	status = "okay";
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+};

Documentation/devicetree/bindings/pci/rcar-pci.txt

+* Renesas RCar PCIe interface
+
+Required properties:
+- compatible: should contain one of the following
+	"renesas,pcie-r8a7779", "renesas,pcie-r8a7790", "renesas,pcie-r8a7791"
+- reg: base address and length of the pcie controller registers.
+- #address-cells: set to <3>
+- #size-cells: set to <2>
+- bus-range: PCI bus numbers covered
+- device_type: set to "pci"
+- ranges: ranges for the PCI memory and I/O regions.
+- dma-ranges: ranges for the inbound memory regions.
+- interrupts: two interrupt sources for MSI interrupts, followed by interrupt
+	source for hardware related interrupts (e.g. link speed change).
+- #interrupt-cells: set to <1>
+- interrupt-map-mask and interrupt-map: standard PCI properties
+	to define the mapping of the PCIe interface to interrupt
+	numbers.
+- clocks: from common clock binding: clock specifiers for the PCIe controller
+	and PCIe bus clocks.
+- clock-names: from common clock binding: should be "pcie" and "pcie_bus".
+
+Example:
+
+SoC specific DT Entry:
+
+	pcie: pcie@fe000000 {
+		compatible = "renesas,pcie-r8a7791";
+		reg = <0 0xfe000000 0 0x80000>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		bus-range = <0x00 0xff>;
+		device_type = "pci";
+		ranges = <0x01000000 0 0x00000000 0 0xfe100000 0 0x00100000
+			  0x02000000 0 0xfe200000 0 0xfe200000 0 0x00200000
+			  0x02000000 0 0x30000000 0 0x30000000 0 0x08000000
+			  0x42000000 0 0x38000000 0 0x38000000 0 0x08000000>;
+		dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000
+			      0x42000000 2 0x00000000 2 0x00000000 0 0x40000000>;
+		interrupts = <0 116 4>, <0 117 4>, <0 118 4>;
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic 0 116 4>;
+		clocks = <&mstp3_clks R8A7791_CLK_PCIE>, <&pcie_bus_clk>;
+		clock-names = "pcie", "pcie_bus";
+		status = "disabled";
+	};

arch/x86/pci/acpi.c

@@ -489,8 +489,12 @@ struct pci_bus *pci_acpi_scan_root(struct acpi_pci_root *root)
 	}
 
 	node = acpi_get_node(device->handle);
-	if (node == NUMA_NO_NODE)
+	if (node == NUMA_NO_NODE) {
 		node = x86_pci_root_bus_node(busnum);
+		if (node != 0 && node != NUMA_NO_NODE)
+			dev_info(&device->dev, FW_BUG "no _PXM; falling back to node %d from hardware (may be inconsistent with ACPI node numbers)\n",
+				node);
+	}
 
 	if (node != NUMA_NO_NODE && !node_online(node))
 		node = NUMA_NO_NODE;

arch/x86/pci/amd_bus.c

@@ -11,27 +11,33 @@
 
 #include "bus_numa.h"
 
-/*
- * This discovers the pcibus <-> node mapping on AMD K8.
- * also get peer root bus resource for io,mmio
- */
+#define AMD_NB_F0_NODE_ID			0x60
+#define AMD_NB_F0_UNIT_ID			0x64
+#define AMD_NB_F1_CONFIG_MAP_REG		0xe0
+
+#define RANGE_NUM				16
+#define AMD_NB_F1_CONFIG_MAP_RANGES		4
 
-struct pci_hostbridge_probe {
+struct amd_hostbridge {
 	u32 bus;
 	u32 slot;
-	u32 vendor;
 	u32 device;
 };
 
-static struct pci_hostbridge_probe pci_probes[] __initdata = {
-	{ 0, 0x18, PCI_VENDOR_ID_AMD, 0x1100 },
-	{ 0, 0x18, PCI_VENDOR_ID_AMD, 0x1200 },
-	{ 0xff, 0, PCI_VENDOR_ID_AMD, 0x1200 },
-	{ 0, 0x18, PCI_VENDOR_ID_AMD, 0x1300 },
+/*
+ * IMPORTANT NOTE:
+ * hb_probes[] and early_root_info_init() is in maintenance mode.
+ * It only supports K8, Fam10h, Fam11h, and Fam15h_00h-0fh .
+ * Future processor will rely on information in ACPI.
+ */
+static struct amd_hostbridge hb_probes[] __initdata = {
+	{ 0, 0x18, 0x1100 }, /* K8 */
+	{ 0, 0x18, 0x1200 }, /* Family10h */
+	{ 0xff, 0, 0x1200 }, /* Family10h */
+	{ 0, 0x18, 0x1300 }, /* Family11h */
+	{ 0, 0x18, 0x1600 }, /* Family15h */
 };
 
-#define RANGE_NUM 16
-
 static struct pci_root_info __init *find_pci_root_info(int node, int link)
 {
 	struct pci_root_info *info;
@@ -45,12 +51,12 @@ static struct pci_root_info __init *find_pci_root_info(int node, int link)
 }
 
 /**
- * early_fill_mp_bus_to_node()
+ * early_root_info_init()
  * called before pcibios_scan_root and pci_scan_bus
- * fills the mp_bus_to_cpumask array based according to the LDT Bus Number
- * Registers found in the K8 northbridge
+ * fills the mp_bus_to_cpumask array based according
+ * to the LDT Bus Number Registers found in the northbridge.
  */
-static int __init early_fill_mp_bus_info(void)
+static int __init early_root_info_init(void)
 {
 	int i;
 	unsigned bus;
@@ -75,19 +81,21 @@ static int __init early_fill_mp_bus_info(void)
 		return -1;
 
 	found = false;
-	for (i = 0; i < ARRAY_SIZE(pci_probes); i++) {
+	for (i = 0; i < ARRAY_SIZE(hb_probes); i++) {
 		u32 id;
 		u16 device;
 		u16 vendor;
 
-		bus = pci_probes[i].bus;
-		slot = pci_probes[i].slot;
+		bus = hb_probes[i].bus;
+		slot = hb_probes[i].slot;
 		id = read_pci_config(bus, slot, 0, PCI_VENDOR_ID);
-
 		vendor = id & 0xffff;
 		device = (id>>16) & 0xffff;
-		if (pci_probes[i].vendor == vendor &&
-		    pci_probes[i].device == device) {
+
+		if (vendor != PCI_VENDOR_ID_AMD)
+			continue;
+
+		if (hb_probes[i].device == device) {
 			found = true;
 			break;
 		}
@@ -96,10 +104,16 @@ static int __init early_fill_mp_bus_info(void)
 	if (!found)
 		return 0;
 
-	for (i = 0; i < 4; i++) {
+	/*
+	 * We should learn topology and routing information from _PXM and
+	 * _CRS methods in the ACPI namespace.  We extract node numbers
+	 * here to work around BIOSes that don't supply _PXM.
+	 */
+	for (i = 0; i < AMD_NB_F1_CONFIG_MAP_RANGES; i++) {
 		int min_bus;
 		int max_bus;
-		reg = read_pci_config(bus, slot, 1, 0xe0 + (i << 2));
+		reg = read_pci_config(bus, slot, 1,
+				AMD_NB_F1_CONFIG_MAP_REG + (i << 2));
 
 		/* Check if that register is enabled for bus range */
 		if ((reg & 7) != 3)
@@ -113,10 +127,21 @@ static int __init early_fill_mp_bus_info(void)
 		info = alloc_pci_root_info(min_bus, max_bus, node, link);
 	}
 
+	/*
+	 * The following code extracts routing information for use on old
+	 * systems where Linux doesn't automatically use host bridge _CRS
+	 * methods (or when the user specifies "pci=nocrs").
+	 *
+	 * We only do this through Fam11h, because _CRS should be enough on
+	 * newer systems.
+	 */
+	if (boot_cpu_data.x86 > 0x11)
+		return 0;
+
 	/* get the default node and link for left over res */
-	reg = read_pci_config(bus, slot, 0, 0x60);
+	reg = read_pci_config(bus, slot, 0, AMD_NB_F0_NODE_ID);
 	def_node = (reg >> 8) & 0x07;
-	reg = read_pci_config(bus, slot, 0, 0x64);
+	reg = read_pci_config(bus, slot, 0, AMD_NB_F0_UNIT_ID);
 	def_link = (reg >> 8) & 0x03;
 
 	memset(range, 0, sizeof(range));
@@ -363,7 +388,7 @@ static int __init pci_io_ecs_init(void)
 	int cpu;
 
 	/* assume all cpus from fam10h have IO ECS */
-        if (boot_cpu_data.x86 < 0x10)
+	if (boot_cpu_data.x86 < 0x10)
 		return 0;
 
 	/* Try the PCI method first. */
@@ -387,7 +412,7 @@ static int __init amd_postcore_init(void)
 	if (boot_cpu_data.x86_vendor != X86_VENDOR_AMD)
 		return 0;
 
-	early_fill_mp_bus_info();
+	early_root_info_init();
 	pci_io_ecs_init();
 
 	return 0;

drivers/pci/host/Kconfig

@@ -33,4 +33,10 @@ config PCI_RCAR_GEN2
 	  There are 3 internal PCI controllers available with a single
 	  built-in EHCI/OHCI host controller present on each one.
 
+config PCI_RCAR_GEN2_PCIE
+	bool "Renesas R-Car PCIe controller"
+	depends on ARCH_SHMOBILE || (ARM && COMPILE_TEST)
+	help
+	  Say Y here if you want PCIe controller support on R-Car Gen2 SoCs.
+
 endmenu

drivers/pci/host/Makefile

@@ -4,3 +4,4 @@ obj-$(CONFIG_PCI_IMX6) += pci-imx6.o
 obj-$(CONFIG_PCI_MVEBU) += pci-mvebu.o
 obj-$(CONFIG_PCI_TEGRA) += pci-tegra.o
 obj-$(CONFIG_PCI_RCAR_GEN2) += pci-rcar-gen2.o
+obj-$(CONFIG_PCI_RCAR_GEN2_PCIE) += pcie-rcar.o

drivers/pci/host/pci-exynos.c

@@ -568,10 +568,8 @@ static int __init exynos_pcie_probe(struct platform_device *pdev)
 
 	exynos_pcie = devm_kzalloc(&pdev->dev, sizeof(*exynos_pcie),
 				GFP_KERNEL);
-	if (!exynos_pcie) {
-		dev_err(&pdev->dev, "no memory for exynos pcie\n");
+	if (!exynos_pcie)
 		return -ENOMEM;
-	}
 
 	pp = &exynos_pcie->pp;
 

drivers/pci/host/pci-rcar-gen2.c

@@ -15,6 +15,7 @@
 #include <linux/io.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
+#include <linux/of_pci.h>
 #include <linux/pci.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
@@ -98,6 +99,7 @@ struct rcar_pci_priv {
 	struct resource io_res;
 	struct resource mem_res;
 	struct resource *cfg_res;
+	unsigned busnr;
 	int irq;
 	unsigned long window_size;
 };
@@ -180,8 +182,13 @@ static int rcar_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
 {
 	struct pci_sys_data *sys = dev->bus->sysdata;
 	struct rcar_pci_priv *priv = sys->private_data;
+	int irq;
+
+	irq = of_irq_parse_and_map_pci(dev, slot, pin);
+	if (!irq)
+		irq = priv->irq;
 
-	return priv->irq;
+	return irq;
 }
 
 #ifdef CONFIG_PCI_DEBUG
@@ -312,8 +319,8 @@ static int rcar_pci_setup(int nr, struct pci_sys_data *sys)
 	pci_add_resource(&sys->resources, &priv->io_res);
 	pci_add_resource(&sys->resources, &priv->mem_res);
 
-	/* Setup bus number based on platform device id */
-	sys->busnr = to_platform_device(priv->dev)->id;
+	/* Setup bus number based on platform device id / of bus-range */
+	sys->busnr = priv->busnr;
 	return 1;
 }
 
@@ -366,6 +373,23 @@ static int rcar_pci_probe(struct platform_device *pdev)
 
 	priv->window_size = SZ_1G;
 
+	if (pdev->dev.of_node) {
+		struct resource busnr;
+		int ret;
+
+		ret = of_pci_parse_bus_range(pdev->dev.of_node, &busnr);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "failed to parse bus-range\n");
+			return ret;
+		}
+
+		priv->busnr = busnr.start;
+		if (busnr.end != busnr.start)
+			dev_warn(&pdev->dev, "only one bus number supported\n");
+	} else {
+		priv->busnr = pdev->id;
+	}
+
 	hw_private[0] = priv;
 	memset(&hw, 0, sizeof(hw));
 	hw.nr_controllers = ARRAY_SIZE(hw_private);
@@ -377,11 +401,20 @@ static int rcar_pci_probe(struct platform_device *pdev)
 	return 0;
 }
 
+static struct of_device_id rcar_pci_of_match[] = {
+	{ .compatible = "renesas,pci-r8a7790", },
+	{ .compatible = "renesas,pci-r8a7791", },
+	{ },
+};
+
+MODULE_DEVICE_TABLE(of, rcar_pci_of_match);
+
 static struct platform_driver rcar_pci_driver = {
 	.driver = {
 		.name = "pci-rcar-gen2",
 		.owner = THIS_MODULE,
 		.suppress_bind_attrs = true,
+		.of_match_table = rcar_pci_of_match,
 	},
 	.probe = rcar_pci_probe,
 };