Commit 7a475267 authored by Nicolas Ferre's avatar Nicolas Ferre

ARM: at91: dt: add device tree file for SAMA5D4ek board

Add reference SAMA5D4-EK platform DT file.
Signed-off-by: default avatarNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: default avatarJosh Wu <josh.wu@atmel.com>
Signed-off-by: default avatarAlexandre Belloni <alexandre.belloni@free-electrons.com>
parent 7c661394
......@@ -48,6 +48,8 @@ dtb-$(CONFIG_ARCH_AT91) += sama5d33ek.dtb
dtb-$(CONFIG_ARCH_AT91) += sama5d34ek.dtb
dtb-$(CONFIG_ARCH_AT91) += sama5d35ek.dtb
dtb-$(CONFIG_ARCH_AT91) += sama5d36ek.dtb
# sama5d4
dtb-$(CONFIG_ARCH_AT91) += at91-sama5d4ek.dtb
dtb-$(CONFIG_ARCH_ATLAS6) += atlas6-evb.dtb
dtb-$(CONFIG_ARCH_AXXIA) += axm5516-amarillo.dtb
......
/*
* at91-sama5d4ek.dts - Device Tree file for SAMA5D4 Evaluation Kit
*
* Copyright (C) 2014 Atmel,
* 2014 Nicolas Ferre <nicolas.ferre@atmel.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sama5d4.dtsi"
/ {
model = "Atmel SAMA5D4-EK";
compatible = "atmel,sama5d4ek", "atmel,sama5d4", "atmel,sama5";
chosen {
bootargs = "console=ttyS0,115200 ignore_loglevel earlyprintk";
};
memory {
reg = <0x20000000 0x20000000>;
};
clocks {
#address-cells = <1>;
#size-cells = <1>;
ranges;
main_clock: clock@0 {
compatible = "atmel,osc", "fixed-clock";
clock-frequency = <12000000>;
};
slow_xtal {
clock-frequency = <32768>;
};
main_xtal {
clock-frequency = <12000000>;
};
};
ahb {
apb {
lcd_bus@f0000000 {
status = "okay";
lcd@f0000000 {
status = "okay";
};
lcdovl1@f0000140 {
status = "okay";
};
lcdovl2@f0000240 {
status = "okay";
};
lcdheo1@f0000340 {
status = "okay";
};
};
adc0: adc@fc034000 {
/* The vref depends on JP22 of EK. If connect 1-2 then use 3.3V. connect 2-3 use 3.0V */
atmel,adc-vref = <3300>;
/*atmel,adc-ts-wires = <4>;*/ /* Set up ADC touch screen */
status = "okay"; /* Enable ADC IIO support */
};
mmc0: mmc@f8000000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
slot@1 {
reg = <1>;
bus-width = <4>;
cd-gpios = <&pioE 5 0>;
};
};
spi0: spi@f8010000 {
cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
status = "okay";
m25p80@0 {
compatible = "atmel,at25df321a";
spi-max-frequency = <50000000>;
reg = <0>;
};
};
i2c0: i2c@f8014000 {
status = "okay";
};
macb0: ethernet@f8020000 {
phy-mode = "rmii";
status = "okay";
};
mmc1: mmc@fc000000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
status = "okay";
slot@0 {
reg = <0>;
bus-width = <4>;
cd-gpios = <&pioE 6 0>;
};
};
usart2: serial@fc008000 {
status = "okay";
};
usart3: serial@fc00c000 {
status = "okay";
};
usart4: serial@fc010000 {
status = "okay";
};
watchdog@fc068640 {
status = "okay";
};
pinctrl@fc06a000 {
board {
pinctrl_mmc0_cd: mmc0_cd {
atmel,pins =
<AT91_PIOE 5 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
};
pinctrl_mmc1_cd: mmc1_cd {
atmel,pins =
<AT91_PIOE 6 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
};
pinctrl_usba_vbus: usba_vbus {
atmel,pins =
<AT91_PIOE 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
};
pinctrl_key_gpio: key_gpio_0 {
atmel,pins =
<AT91_PIOE 13 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PE13 gpio */
};
};
};
};
usb0: gadget@00400000 {
atmel,vbus-gpio = <&pioE 31 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usba_vbus>;
status = "okay";
};
usb1: ohci@00500000 {
num-ports = <3>;
atmel,vbus-gpio = <0 /* &pioE 10 GPIO_ACTIVE_LOW */
&pioE 11 GPIO_ACTIVE_LOW
&pioE 12 GPIO_ACTIVE_LOW
>;
status = "okay";
};
usb2: ehci@00600000 {
status = "okay";
};
nand0: nand@80000000 {
nand-bus-width = <8>;
nand-ecc-mode = "hw";
nand-on-flash-bbt;
atmel,has-pmecc;
status = "okay";
at91bootstrap@0 {
label = "at91bootstrap";
reg = <0x0 0x40000>;
};
bootloader@40000 {
label = "bootloader";
reg = <0x40000 0x80000>;
};
bootloaderenv@c0000 {
label = "bootloader env";
reg = <0xc0000 0xc0000>;
};
dtb@180000 {
label = "device tree";
reg = <0x180000 0x80000>;
};
kernel@200000 {
label = "kernel";
reg = <0x200000 0x600000>;
};
rootfs@800000 {
label = "rootfs";
reg = <0x800000 0x0f800000>;
};
};
};
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_key_gpio>;
pb_user1 {
label = "pb_user1";
gpios = <&pioE 13 GPIO_ACTIVE_HIGH>;
linux,code = <0x100>;
gpio-key,wakeup;
};
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment