stmmac: Move the STMicroelectronics driver

Move the STMicroelectronics driver into driver/net/ethernet/stmicro/ and
make the necessary Kconfig and Makefile changes.

CC: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

MAINTAINERS

@@ -2029,7 +2029,7 @@ M:	Giuseppe Cavallaro <peppe.cavallaro@st.com>
 L:	netdev@vger.kernel.org
 W:	http://www.stlinux.com
 S:	Supported
-F:	drivers/net/stmmac/
+F:	drivers/net/ethernet/stmicro/stmmac/
 
 CYBERPRO FB DRIVER
 M:	Russell King <linux@arm.linux.org.uk>

drivers/net/Kconfig

@@ -1406,8 +1406,6 @@ config S6GMAC
 	  To compile this driver as a module, choose M here. The module
 	  will be called s6gmac.
 
-source "drivers/net/stmmac/Kconfig"
-
 config PCH_GBE
 	tristate "Intel EG20T PCH / OKI SEMICONDUCTOR ML7223 IOH GbE"
 	depends on PCI

drivers/net/Makefile

@@ -67,7 +67,6 @@ obj-$(CONFIG_VIA_VELOCITY) += via-velocity.o
 obj-$(CONFIG_ADAPTEC_STARFIRE) += starfire.o
 obj-$(CONFIG_RIONET) += rionet.o
 obj-$(CONFIG_SH_ETH) += sh_eth.o
-obj-$(CONFIG_STMMAC_ETH) += stmmac/
 
 #
 # end link order section

drivers/net/ethernet/Kconfig

@@ -30,6 +30,7 @@ source "drivers/net/ethernet/qlogic/Kconfig"
 source "drivers/net/ethernet/racal/Kconfig"
 source "drivers/net/ethernet/sfc/Kconfig"
 source "drivers/net/ethernet/smsc/Kconfig"
+source "drivers/net/ethernet/stmicro/Kconfig"
 source "drivers/net/ethernet/sun/Kconfig"
 source "drivers/net/ethernet/tehuti/Kconfig"
 

drivers/net/ethernet/Makefile

@@ -21,5 +21,6 @@ obj-$(CONFIG_NET_VENDOR_QLOGIC) += qlogic/
 obj-$(CONFIG_NET_VENDOR_RACAL) += racal/
 obj-$(CONFIG_SFC) += sfc/
 obj-$(CONFIG_NET_VENDOR_SMSC) += smsc/
+obj-$(CONFIG_NET_VENDOR_STMICRO) += stmicro/
 obj-$(CONFIG_NET_VENDOR_SUN) += sun/
 obj-$(CONFIG_NET_VENDOR_TEHUTI) += tehuti/

drivers/net/ethernet/stmicro/Kconfig

+#
+# STMicroelectronics device configuration
+#
+
+config NET_VENDOR_STMICRO
+	bool "STMicroelectronics devices"
+	depends on HAS_IOMEM
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about STMicroelectronics cards. If you say Y, you will
+	  be asked for your specific card in the following questions.
+
+if NET_VENDOR_STMICRO
+
+source "drivers/net/ethernet/stmicro/stmmac/Kconfig"
+
+endif # NET_VENDOR_STMICRO

drivers/net/ethernet/stmicro/Makefile

+#
+# Makefile for the STMicroelectronics device drivers.
+#
+
+obj-$(CONFIG_STMMAC_ETH) += stmmac/

drivers/net/stmmac/Kconfig → drivers/net/ethernet/stmicro/stmmac/Kconfig

 config STMMAC_ETH
 	tristate "STMicroelectronics 10/100/1000 Ethernet driver"
+	depends on HAS_IOMEM
 	select MII
 	select PHYLIB
 	select CRC32
-	depends on NETDEVICES && HAS_IOMEM
-	help
+	---help---
 	  This is the driver for the Ethernet IPs are built around a
 	  Synopsys IP Core and only tested on the STMicroelectronics
 	  platforms.
@@ -14,7 +14,7 @@ if STMMAC_ETH
 config STMMAC_DA
 	bool "STMMAC DMA arbitration scheme"
 	default n
-	help
+	---help---
 	  Selecting this option, rx has priority over Tx (only for Giga
 	  Ethernet device).
 	  By default, the DMA arbitration scheme is based on Round-robin
@@ -24,7 +24,7 @@ config STMMAC_DUAL_MAC
 	bool "STMMAC: dual mac support (EXPERIMENTAL)"
 	default n
         depends on EXPERIMENTAL && STMMAC_ETH && !STMMAC_TIMER
-	help
+	---help---
 	  Some ST SoCs (for example the stx7141 and stx7200c2) have two
 	  Ethernet Controllers. This option turns on the second Ethernet
 	  device on this kind of platforms.
@@ -33,7 +33,7 @@ config STMMAC_TIMER
 	bool "STMMAC Timer optimisation"
 	default n
 	depends on RTC_HCTOSYS_DEVICE
-	help
+	---help---
 	  Use an external timer for mitigating the number of network
 	  interrupts. Currently, for SH architectures, it is possible
 	  to use the TMU channel 2 and the SH-RTC device.
@@ -45,12 +45,12 @@ choice
 config STMMAC_TMU_TIMER
         bool "TMU channel 2"
         depends on CPU_SH4
-	help
+	---help---
 
 config STMMAC_RTC_TIMER
         bool "Real time clock"
         depends on RTC_CLASS
-	help
+	---help---
 
 endchoice