Merge branch 'master' of...

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

drivers/bcma/Kconfig

@@ -67,8 +67,7 @@ config BCMA_DRIVER_GMAC_CMN
 
 config BCMA_DRIVER_GPIO
 	bool "BCMA GPIO driver"
-	depends on BCMA
-	select GPIOLIB
+	depends on BCMA && GPIOLIB
 	help
 	  Driver to provide access to the GPIO pins of the bcma bus.
 

drivers/bcma/driver_chipcommon_sflash.c

@@ -35,7 +35,7 @@ static struct bcma_sflash_tbl_e bcma_sflash_st_tbl[] = {
 	{ "M25P40", 0x12, 0x10000, 8, },
 
 	{ "M25P16", 0x14, 0x10000, 32, },
-	{ "M25P32", 0x14, 0x10000, 64, },
+	{ "M25P32", 0x15, 0x10000, 64, },
 	{ "M25P64", 0x16, 0x10000, 128, },
 	{ "M25FL128", 0x17, 0x10000, 256, },
 	{ 0 },

drivers/net/wireless/ath/ath9k/Kconfig

@@ -2,6 +2,7 @@ config ATH9K_HW
 	tristate
 config ATH9K_COMMON
 	tristate
+	select ATH_COMMON
 config ATH9K_DFS_DEBUGFS
 	def_bool y
 	depends on ATH9K_DEBUGFS && ATH9K_DFS_CERTIFIED
@@ -17,7 +18,6 @@ config ATH9K_BTCOEX_SUPPORT
 config ATH9K
 	tristate "Atheros 802.11n wireless cards support"
 	depends on MAC80211
-	select ATH_COMMON
 	select ATH9K_HW
 	select MAC80211_LEDS
 	select LEDS_CLASS
@@ -56,7 +56,8 @@ config ATH9K_AHB
 
 config ATH9K_DEBUGFS
 	bool "Atheros ath9k debugging"
-	depends on ATH9K && DEBUG_FS
+	depends on ATH9K
+	select MAC80211_DEBUGFS
 	---help---
 	  Say Y, if you need access to ath9k's statistics for
 	  interrupts, rate control, etc.

drivers/net/wireless/ath/ath9k/ar9003_hw.c

@@ -544,7 +544,7 @@ static void ar9003_rx_gain_table_mode0(struct ath_hw *ah)
 				ar9340Common_rx_gain_table_1p0);
 	else if (AR_SREV_9485_11(ah))
 		INIT_INI_ARRAY(&ah->iniModesRxGain,
-				ar9485Common_wo_xlna_rx_gain_1_1);
+			       ar9485_common_rx_gain_1_1);
 	else if (AR_SREV_9550(ah)) {
 		INIT_INI_ARRAY(&ah->iniModesRxGain,
 				ar955x_1p0_common_rx_gain_table);

drivers/net/wireless/ath/carl9170/fw.c

@@ -336,8 +336,12 @@ static int carl9170_fw(struct ar9170 *ar, const __u8 *data, size_t len)
 		if (SUPP(CARL9170FW_WLANTX_CAB)) {
 			if_comb_types |=
 				BIT(NL80211_IFTYPE_AP) |
-				BIT(NL80211_IFTYPE_MESH_POINT) |
 				BIT(NL80211_IFTYPE_P2P_GO);
+
+#ifdef CONFIG_MAC80211_MESH
+			if_comb_types |=
+				BIT(NL80211_IFTYPE_MESH_POINT);
+#endif /* CONFIG_MAC80211_MESH */
 		}
 	}
 

drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c

@@ -3091,10 +3091,11 @@ brcmf_configure_wpaie(struct net_device *ndev, struct brcmf_vs_tlv *wpa_ie,
 
 	len = wpa_ie->len + TLV_HDR_LEN;
 	data = (u8 *)wpa_ie;
-	offset = 0;
+	offset = TLV_HDR_LEN;
 	if (!is_rsn_ie)
 		offset += VS_IE_FIXED_HDR_LEN;
-	offset += WPA_IE_VERSION_LEN;
+	else
+		offset += WPA_IE_VERSION_LEN;
 
 	/* check for multicast cipher suite */
 	if (offset + WPA_IE_MIN_OUI_LEN > len) {

drivers/net/wireless/brcm80211/brcmsmac/debug.h

 /*
  * Copyright (c) 2012 Broadcom Corporation
+ * Copyright (c) 2012 Canonical Ltd.
  *
  * Permission to use, copy, modify, and/or distribute this software for any
  * purpose with or without fee is hereby granted, provided that the above

drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c

@@ -1343,13 +1343,13 @@ static bool wlc_lcnphy_rx_iq_cal_gain(struct brcms_phy *pi, u16 biq1_gain,
 
 	wlc_lcnphy_rx_gain_override_enable(pi, true);
 	wlc_lcnphy_start_tx_tone(pi, 2000, (40 >> 1), 0);
-	usleep_range(500, 500);
+	udelay(500);
 	write_radio_reg(pi, RADIO_2064_REG112, 0);
 	if (!wlc_lcnphy_rx_iq_est(pi, 1024, 32, &iq_est_l))
 		return false;
 
 	wlc_lcnphy_start_tx_tone(pi, 2000, 40, 0);
-	usleep_range(500, 500);
+	udelay(500);
 	write_radio_reg(pi, RADIO_2064_REG112, 0);
 	if (!wlc_lcnphy_rx_iq_est(pi, 1024, 32, &iq_est_h))
 		return false;

drivers/net/wireless/p54/p54usb.c

@@ -47,6 +47,7 @@ static struct usb_device_id p54u_table[] = {
 	{USB_DEVICE(0x0411, 0x0050)},	/* Buffalo WLI2-USB2-G54 */
 	{USB_DEVICE(0x045e, 0x00c2)},	/* Microsoft MN-710 */
 	{USB_DEVICE(0x0506, 0x0a11)},	/* 3COM 3CRWE254G72 */
+	{USB_DEVICE(0x0675, 0x0530)},	/* DrayTek Vigor 530 */
 	{USB_DEVICE(0x06b9, 0x0120)},	/* Thomson SpeedTouch 120g */
 	{USB_DEVICE(0x0707, 0xee06)},	/* SMC 2862W-G */
 	{USB_DEVICE(0x07aa, 0x001c)},	/* Corega CG-WLUSB2GT */
@@ -82,6 +83,8 @@ static struct usb_device_id p54u_table[] = {
 	{USB_DEVICE(0x06a9, 0x000e)},	/* Westell 802.11g USB (A90-211WG-01) */
 	{USB_DEVICE(0x06b9, 0x0121)},	/* Thomson SpeedTouch 121g */
 	{USB_DEVICE(0x0707, 0xee13)},   /* SMC 2862W-G version 2 */
+	{USB_DEVICE(0x0803, 0x4310)},	/* Zoom 4410a */
+	{USB_DEVICE(0x083a, 0x4503)},	/* T-Com Sinus 154 data II */
 	{USB_DEVICE(0x083a, 0x4521)},   /* Siemens Gigaset USB Adapter 54 version 2 */
 	{USB_DEVICE(0x083a, 0xc501)},	/* Zoom Wireless-G 4410 */
 	{USB_DEVICE(0x083a, 0xf503)},	/* Accton FD7050E ver 1010ec  */
@@ -101,6 +104,7 @@ static struct usb_device_id p54u_table[] = {
 	{USB_DEVICE(0x13B1, 0x000C)},	/* Linksys WUSB54AG */
 	{USB_DEVICE(0x1413, 0x5400)},   /* Telsey 802.11g USB2.0 Adapter */
 	{USB_DEVICE(0x1435, 0x0427)},	/* Inventel UR054G */
+	/* {USB_DEVICE(0x15a9, 0x0002)}, * Also SparkLAN WL-682 with 3887 */
 	{USB_DEVICE(0x1668, 0x1050)},	/* Actiontec 802UIG-1 */
 	{USB_DEVICE(0x1740, 0x1000)},	/* Senao NUB-350 */
 	{USB_DEVICE(0x2001, 0x3704)},	/* DLink DWL-G122 rev A2 */

drivers/net/wireless/rtlwifi/pci.c

@@ -743,6 +743,8 @@ static void _rtl_pci_rx_interrupt(struct ieee80211_hw *hw)
 
 done:
 		bufferaddress = (*((dma_addr_t *)skb->cb));
+		if (pci_dma_mapping_error(rtlpci->pdev, bufferaddress))
+			return;
 		tmp_one = 1;
 		rtlpriv->cfg->ops->set_desc((u8 *) pdesc, false,
 					    HW_DESC_RXBUFF_ADDR,
@@ -1115,6 +1117,10 @@ static int _rtl_pci_init_rx_ring(struct ieee80211_hw *hw)
 					   PCI_DMA_FROMDEVICE);
 
 			bufferaddress = (*((dma_addr_t *)skb->cb));
+			if (pci_dma_mapping_error(rtlpci->pdev, bufferaddress)) {
+				dev_kfree_skb_any(skb);
+				return 1;
+			}
 			rtlpriv->cfg->ops->set_desc((u8 *)entry, false,
 						    HW_DESC_RXBUFF_ADDR,
 						    (u8 *)&bufferaddress);

drivers/net/wireless/rtlwifi/rtl8192ce/trx.c

@@ -611,8 +611,14 @@ void rtl92ce_tx_fill_desc(struct ieee80211_hw *hw,
 	dma_addr_t mapping = pci_map_single(rtlpci->pdev,
 					    skb->data, skb->len,
 					    PCI_DMA_TODEVICE);
+
 	u8 bw_40 = 0;
 
+	if (pci_dma_mapping_error(rtlpci->pdev, mapping)) {
+		RT_TRACE(rtlpriv, COMP_SEND, DBG_TRACE,
+			 "DMA mapping error");
+		return;
+	}
 	rcu_read_lock();
 	sta = get_sta(hw, mac->vif, mac->bssid);
 	if (mac->opmode == NL80211_IFTYPE_STATION) {
@@ -774,6 +780,11 @@ void rtl92ce_tx_fill_cmddesc(struct ieee80211_hw *hw,
 	struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)(skb->data);
 	__le16 fc = hdr->frame_control;
 
+	if (pci_dma_mapping_error(rtlpci->pdev, mapping)) {
+		RT_TRACE(rtlpriv, COMP_SEND, DBG_TRACE,
+			 "DMA mapping error");
+		return;
+	}
 	CLEAR_PCI_TX_DESC_CONTENT(pdesc, TX_DESC_SIZE);
 
 	if (firstseg)

drivers/net/wireless/rtlwifi/rtl8192de/trx.c

@@ -587,6 +587,11 @@ void rtl92de_tx_fill_desc(struct ieee80211_hw *hw,
 	buf_len = skb->len;
 	mapping = pci_map_single(rtlpci->pdev, skb->data, skb->len,
 				 PCI_DMA_TODEVICE);
+	if (pci_dma_mapping_error(rtlpci->pdev, mapping)) {
+		RT_TRACE(rtlpriv, COMP_SEND, DBG_TRACE,
+			 "DMA mapping error");
+		return;
+	}
 	CLEAR_PCI_TX_DESC_CONTENT(pdesc, sizeof(struct tx_desc_92d));
 	if (ieee80211_is_nullfunc(fc) || ieee80211_is_ctl(fc)) {
 		firstseg = true;
@@ -740,6 +745,11 @@ void rtl92de_tx_fill_cmddesc(struct ieee80211_hw *hw,
 	struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)(skb->data);
 	__le16 fc = hdr->frame_control;
 
+	if (pci_dma_mapping_error(rtlpci->pdev, mapping)) {
+		RT_TRACE(rtlpriv, COMP_SEND, DBG_TRACE,
+			 "DMA mapping error");
+		return;
+	}
 	CLEAR_PCI_TX_DESC_CONTENT(pdesc, TX_DESC_SIZE);
 	if (firstseg)
 		SET_TX_DESC_OFFSET(pdesc, USB_HWDESC_HEADER_LEN);

drivers/net/wireless/rtlwifi/rtl8192se/trx.c

@@ -611,6 +611,11 @@ void rtl92se_tx_fill_desc(struct ieee80211_hw *hw,
 		    PCI_DMA_TODEVICE);
 	u8 bw_40 = 0;
 
+	if (pci_dma_mapping_error(rtlpci->pdev, mapping)) {
+		RT_TRACE(rtlpriv, COMP_SEND, DBG_TRACE,
+			 "DMA mapping error");
+		return;
+	}
 	if (mac->opmode == NL80211_IFTYPE_STATION) {
 		bw_40 = mac->bw_40;
 	} else if (mac->opmode == NL80211_IFTYPE_AP ||
@@ -763,6 +768,7 @@ void rtl92se_tx_fill_desc(struct ieee80211_hw *hw,
 void rtl92se_tx_fill_cmddesc(struct ieee80211_hw *hw, u8 *pdesc,
 	bool firstseg, bool lastseg, struct sk_buff *skb)
 {
+	struct rtl_priv *rtlpriv = rtl_priv(hw);
 	struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
 	struct rtl_hal *rtlhal = rtl_hal(rtl_priv(hw));
 	struct rtl_tcb_desc *tcb_desc = (struct rtl_tcb_desc *)(skb->cb);
@@ -770,7 +776,12 @@ void rtl92se_tx_fill_cmddesc(struct ieee80211_hw *hw, u8 *pdesc,
 	dma_addr_t mapping = pci_map_single(rtlpci->pdev, skb->data, skb->len,
 			PCI_DMA_TODEVICE);
 
-    /* Clear all status	*/
+	if (pci_dma_mapping_error(rtlpci->pdev, mapping)) {
+		RT_TRACE(rtlpriv, COMP_SEND, DBG_TRACE,
+			 "DMA mapping error");
+		return;
+	}
+	/* Clear all status	*/
 	CLEAR_PCI_TX_DESC_CONTENT(pdesc, TX_CMDDESC_SIZE_RTL8192S);
 
 	/* This bit indicate this packet is used for FW download. */

drivers/net/wireless/rtlwifi/rtl8723ae/trx.c

@@ -387,6 +387,11 @@ void rtl8723ae_tx_fill_desc(struct ieee80211_hw *hw,
 					    PCI_DMA_TODEVICE);
 	u8 bw_40 = 0;
 
+	if (pci_dma_mapping_error(rtlpci->pdev, mapping)) {
+		RT_TRACE(rtlpriv, COMP_SEND, DBG_TRACE,
+			 "DMA mapping error");
+		return;
+	}
 	if (mac->opmode == NL80211_IFTYPE_STATION) {
 		bw_40 = mac->bw_40;
 	} else if (mac->opmode == NL80211_IFTYPE_AP ||
@@ -542,6 +547,11 @@ void rtl8723ae_tx_fill_cmddesc(struct ieee80211_hw *hw,
 					    PCI_DMA_TODEVICE);
 	__le16 fc = hdr->frame_control;
 
+	if (pci_dma_mapping_error(rtlpci->pdev, mapping)) {
+		RT_TRACE(rtlpriv, COMP_SEND, DBG_TRACE,
+			 "DMA mapping error");
+		return;
+	}
 	CLEAR_PCI_TX_DESC_CONTENT(pdesc, TX_DESC_SIZE);
 
 	if (firstseg)

drivers/net/wireless/rtlwifi/usb.c

@@ -210,17 +210,16 @@ static void _usb_writeN_sync(struct rtl_priv *rtlpriv, u32 addr, void *data,
 	u16 index = REALTEK_USB_VENQT_CMD_IDX;
 	int pipe = usb_sndctrlpipe(udev, 0); /* write_out */
 	u8 *buffer;
-	dma_addr_t dma_addr;
 
-	wvalue = (u16)(addr&0x0000ffff);
-	buffer = usb_alloc_coherent(udev, (size_t)len, GFP_ATOMIC, &dma_addr);
+	wvalue = (u16)(addr & 0x0000ffff);
+	buffer = kmalloc(len, GFP_ATOMIC);
 	if (!buffer)
 		return;
 	memcpy(buffer, data, len);
 	usb_control_msg(udev, pipe, request, reqtype, wvalue,
 			index, buffer, len, 50);
 
-	usb_free_coherent(udev, (size_t)len, buffer, dma_addr);
+	kfree(buffer);
 }
 
 static void _rtl_usb_io_handler_init(struct device *dev,
@@ -640,6 +639,7 @@ static int _rtl_usb_receive(struct ieee80211_hw *hw)
 			RT_TRACE(rtlpriv, COMP_USB, DBG_EMERG,
 				 "Failed to prep_rx_urb!!\n");
 			err = PTR_ERR(skb);
+			usb_free_urb(urb);
 			goto err_out;
 		}
 

drivers/ssb/Kconfig

@@ -162,8 +162,7 @@ config SSB_DRIVER_GIGE
 
 config SSB_DRIVER_GPIO
 	bool "SSB GPIO driver"
-	depends on SSB
-	select GPIOLIB
+	depends on SSB && GPIOLIB
 	help
 	  Driver to provide access to the GPIO pins on the bus.