Commit 7bdb2b6a authored by Linus Torvalds's avatar Linus Torvalds

Merge master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6

parents 4c2cac89 c0f2f761
......@@ -178,8 +178,6 @@ endchoice
endmenu
source "drivers/firmware/Kconfig"
source "mm/Kconfig"
config GENERIC_ISA_DMA
......
......@@ -175,7 +175,7 @@ config MOXA_INTELLIO
config MOXA_SMARTIO
tristate "Moxa SmartIO support"
depends on SERIAL_NONSTANDARD && (BROKEN || !SPARC32)
depends on SERIAL_NONSTANDARD
help
Say Y here if you have a Moxa SmartIO multiport serial card.
......@@ -735,7 +735,7 @@ config SGI_IP27_RTC
config GEN_RTC
tristate "Generic /dev/rtc emulation"
depends on RTC!=y && !IA64 && !ARM && !PPC64 && !M32R && !SPARC32
depends on RTC!=y && !IA64 && !ARM && !PPC64 && !M32R && !SPARC32 && !SPARC64
---help---
If you say Y here and create a character special file /dev/rtc with
major number 10 and minor number 135 using mknod ("man mknod"), you
......
......@@ -63,7 +63,6 @@
#include <asm/system.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/segment.h>
#include <asm/bitops.h>
#include <asm/uaccess.h>
......
......@@ -938,10 +938,9 @@ static int __init rtc_init(void)
/*
* XXX Interrupt pin #7 in Espresso is shared between RTC and
* PCI Slot 2 INTA# (and some INTx# in Slot 1). SA_INTERRUPT here
* is asking for trouble with add-on boards. Change to SA_SHIRQ.
* PCI Slot 2 INTA# (and some INTx# in Slot 1).
*/
if (request_irq(rtc_irq, rtc_interrupt, SA_INTERRUPT, "rtc", (void *)&rtc_port)) {
if (request_irq(rtc_irq, rtc_interrupt, SA_SHIRQ, "rtc", (void *)&rtc_port)) {
/*
* Standard way for sparc to print irq's is to use
* __irq_itoa(). I think for EBus it's ok to use %d.
......
......@@ -269,7 +269,10 @@ static void sunsu_stop_tx(struct uart_port *port)
__stop_tx(up);
if (up->port.type == PORT_16C950 && tty_stop /*FIXME*/) {
/*
* We really want to stop the transmitter from sending.
*/
if (up->port.type == PORT_16C950) {
up->acr |= UART_ACR_TXDIS;
serial_icr_write(up, UART_ACR, up->acr);
}
......@@ -283,10 +286,11 @@ static void sunsu_start_tx(struct uart_port *port)
up->ier |= UART_IER_THRI;
serial_out(up, UART_IER, up->ier);
}
/*
* We only do this from uart_start
* Re-enable the transmitter if we disabled it.
*/
if (tty_start && up->port.type == PORT_16C950 /*FIXME*/) {
if (up->port.type == PORT_16C950 && up->acr & UART_ACR_TXDIS) {
up->acr &= ~UART_ACR_TXDIS;
serial_icr_write(up, UART_ACR, up->acr);
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment