Commit 7c0db24c authored by John David Anglin's avatar John David Anglin Committed by David S. Miller

dsa: mv88e6xxx: Ensure all pending interrupts are handled prior to exit

The GPIO interrupt controller on the espressobin board only supports edge interrupts.
If one enables the use of hardware interrupts in the device tree for the 88E6341, it is
possible to miss an edge.  When this happens, the INTn pin on the Marvell switch is
stuck low and no further interrupts occur.

I found after adding debug statements to mv88e6xxx_g1_irq_thread_work() that there is
a race in handling device interrupts (e.g. PHY link interrupts).  Some interrupts are
directly cleared by reading the Global 1 status register.  However, the device interrupt
flag, for example, is not cleared until all the unmasked SERDES and PHY ports are serviced.
This is done by reading the relevant SERDES and PHY status register.

The code only services interrupts whose status bit is set at the time of reading its status
register.  If an interrupt event occurs after its status is read and before all interrupts
are serviced, then this event will not be serviced and the INTn output pin will remain low.

This is not a problem with polling or level interrupts since the handler will be called
again to process the event.  However, it's a big problem when using level interrupts.

The fix presented here is to add a loop around the code servicing switch interrupts.  If
any pending interrupts remain after the current set has been handled, we loop and process
the new set.  If there are no pending interrupts after servicing, we are sure that INTn has
gone high and we will get an edge when a new event occurs.

Tested on espressobin board.

Fixes: dc30c35b ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: default avatarJohn David Anglin <dave.anglin@bell.net>
Tested-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent b79555d5
...@@ -261,6 +261,7 @@ static irqreturn_t mv88e6xxx_g1_irq_thread_work(struct mv88e6xxx_chip *chip) ...@@ -261,6 +261,7 @@ static irqreturn_t mv88e6xxx_g1_irq_thread_work(struct mv88e6xxx_chip *chip)
unsigned int sub_irq; unsigned int sub_irq;
unsigned int n; unsigned int n;
u16 reg; u16 reg;
u16 ctl1;
int err; int err;
mutex_lock(&chip->reg_lock); mutex_lock(&chip->reg_lock);
...@@ -270,13 +271,28 @@ static irqreturn_t mv88e6xxx_g1_irq_thread_work(struct mv88e6xxx_chip *chip) ...@@ -270,13 +271,28 @@ static irqreturn_t mv88e6xxx_g1_irq_thread_work(struct mv88e6xxx_chip *chip)
if (err) if (err)
goto out; goto out;
for (n = 0; n < chip->g1_irq.nirqs; ++n) { do {
if (reg & (1 << n)) { for (n = 0; n < chip->g1_irq.nirqs; ++n) {
sub_irq = irq_find_mapping(chip->g1_irq.domain, n); if (reg & (1 << n)) {
handle_nested_irq(sub_irq); sub_irq = irq_find_mapping(chip->g1_irq.domain,
++nhandled; n);
handle_nested_irq(sub_irq);
++nhandled;
}
} }
}
mutex_lock(&chip->reg_lock);
err = mv88e6xxx_g1_read(chip, MV88E6XXX_G1_CTL1, &ctl1);
if (err)
goto unlock;
err = mv88e6xxx_g1_read(chip, MV88E6XXX_G1_STS, &reg);
unlock:
mutex_unlock(&chip->reg_lock);
if (err)
goto out;
ctl1 &= GENMASK(chip->g1_irq.nirqs, 0);
} while (reg & ctl1);
out: out:
return (nhandled > 0 ? IRQ_HANDLED : IRQ_NONE); return (nhandled > 0 ? IRQ_HANDLED : IRQ_NONE);
} }
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment