Merge branch 'for-greg' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

* 'for-greg' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
  usb: musb: omap2430: minor cleanups.
  usb: dwc3: unmap the proper number of sg entries
  usb: musb: fix shutdown while usb gadget is in use
  usb: gadget: f_mass_storage: Use "bool" instead of "int" in fsg_module_parameters
  usb: gadget: check for streams only for SS udcs
  usb: gadget: fsl_udc: fix the usage of udc->max_ep
  drivers: usb: otg: Fix dependencies for some OTG drivers
  usb: renesas: silence uninitialized variable report in usbhsg_recip_run_handle()
  usb: gadget: SS Isoc endpoints use comp_desc->bMaxBurst too
  usb: gadget: storage: endian fix
  usb: dwc3: ep0: fix compile warning
  usb: musb: davinci: fix build breakage
  usb: gadget: langwell: don't call gadget's disconnect()
  usb: gadget: langwell: drop langwell_otg support
  usb: otg: kill langwell_otg driver
  usb: dwc3: ep0: tidy up Pending Request handling

drivers/usb/dwc3/ep0.c

@@ -126,7 +126,6 @@ static int __dwc3_gadget_ep0_queue(struct dwc3_ep *dep,
 		struct dwc3_request *req)
 {
 	struct dwc3		*dwc = dep->dwc;
-	u32			type;
 	int			ret = 0;
 
 	req->request.actual	= 0;
@@ -149,20 +148,14 @@ static int __dwc3_gadget_ep0_queue(struct dwc3_ep *dep,
 
 		direction = !!(dep->flags & DWC3_EP0_DIR_IN);
 
-		if (dwc->ep0state == EP0_STATUS_PHASE) {
-			type = dwc->three_stage_setup
-				? DWC3_TRBCTL_CONTROL_STATUS3
-				: DWC3_TRBCTL_CONTROL_STATUS2;
-		} else if (dwc->ep0state == EP0_DATA_PHASE) {
-			type = DWC3_TRBCTL_CONTROL_DATA;
-		} else {
-			/* should never happen */
-			WARN_ON(1);
+		if (dwc->ep0state != EP0_DATA_PHASE) {
+			dev_WARN(dwc->dev, "Unexpected pending request\n");
 			return 0;
 		}
 
 		ret = dwc3_ep0_start_trans(dwc, direction,
-				req->request.dma, req->request.length, type);
+				req->request.dma, req->request.length,
+				DWC3_TRBCTL_CONTROL_DATA);
 		dep->flags &= ~(DWC3_EP_PENDING_REQUEST |
 				DWC3_EP0_DIR_IN);
 	} else if (dwc->delayed_status) {

drivers/usb/dwc3/gadget.c

@@ -101,7 +101,7 @@ void dwc3_unmap_buffer_from_dma(struct dwc3_request *req)
 	if (req->request.num_mapped_sgs) {
 		req->request.dma = DMA_ADDR_INVALID;
 		dma_unmap_sg(dwc->dev, req->request.sg,
-				req->request.num_sgs,
+				req->request.num_mapped_sgs,
 				req->direction ? DMA_TO_DEVICE
 				: DMA_FROM_DEVICE);
 

drivers/usb/gadget/composite.c

@@ -175,13 +175,12 @@ int config_ep_by_speed(struct usb_gadget *g,
 	_ep->comp_desc = comp_desc;
 	if (g->speed == USB_SPEED_SUPER) {
 		switch (usb_endpoint_type(_ep->desc)) {
-		case USB_ENDPOINT_XFER_BULK:
-		case USB_ENDPOINT_XFER_INT:
-			_ep->maxburst = comp_desc->bMaxBurst;
-			break;
 		case USB_ENDPOINT_XFER_ISOC:
 			/* mult: bits 1:0 of bmAttributes */
 			_ep->mult = comp_desc->bmAttributes & 0x3;
+		case USB_ENDPOINT_XFER_BULK:
+		case USB_ENDPOINT_XFER_INT:
+			_ep->maxburst = comp_desc->bMaxBurst;
 			break;
 		default:
 			/* Do nothing for control endpoints */

drivers/usb/gadget/epautoconf.c

@@ -126,7 +126,7 @@ ep_matches (
 	 * descriptor and see if the EP matches it
 	 */
 	if (usb_endpoint_xfer_bulk(desc)) {
-		if (ep_comp) {
+		if (ep_comp && gadget->max_speed >= USB_SPEED_SUPER) {
 			num_req_streams = ep_comp->bmAttributes & 0x1f;
 			if (num_req_streams > ep->max_streams)
 				return 0;

drivers/usb/gadget/f_mass_storage.c

@@ -3123,15 +3123,15 @@ fsg_add(struct usb_composite_dev *cdev, struct usb_configuration *c,
 
 struct fsg_module_parameters {
 	char		*file[FSG_MAX_LUNS];
-	int		ro[FSG_MAX_LUNS];
-	int		removable[FSG_MAX_LUNS];
-	int		cdrom[FSG_MAX_LUNS];
-	int		nofua[FSG_MAX_LUNS];
+	bool		ro[FSG_MAX_LUNS];
+	bool		removable[FSG_MAX_LUNS];
+	bool		cdrom[FSG_MAX_LUNS];
+	bool		nofua[FSG_MAX_LUNS];
 
 	unsigned int	file_count, ro_count, removable_count, cdrom_count;
 	unsigned int	nofua_count;
 	unsigned int	luns;	/* nluns */
-	int		stall;	/* can_stall */
+	bool		stall;	/* can_stall */
 };
 
 #define _FSG_MODULE_PARAM_ARRAY(prefix, params, name, type, desc)	\

drivers/usb/gadget/fsl_udc_core.c

@@ -1430,7 +1430,7 @@ static void setup_received_irq(struct fsl_udc *udc,
 			int pipe = get_pipe_by_windex(wIndex);
 			struct fsl_ep *ep;
 
-			if (wValue != 0 || wLength != 0 || pipe > udc->max_ep)
+			if (wValue != 0 || wLength != 0 || pipe >= udc->max_ep)
 				break;
 			ep = get_ep_by_pipe(udc, pipe);
 
@@ -1673,7 +1673,7 @@ static void dtd_complete_irq(struct fsl_udc *udc)
 	if (!bit_pos)
 		return;
 
-	for (i = 0; i < udc->max_ep * 2; i++) {
+	for (i = 0; i < udc->max_ep; i++) {
 		ep_num = i >> 1;
 		direction = i % 2;
 

drivers/usb/gadget/langwell_udc.c

@@ -11,11 +11,6 @@
 /* #undef	DEBUG */
 /* #undef	VERBOSE_DEBUG */
 
-#if defined(CONFIG_USB_LANGWELL_OTG)
-#define	OTG_TRANSCEIVER
-#endif
-
-
 #include <linux/module.h>
 #include <linux/pci.h>
 #include <linux/dma-mapping.h>
@@ -1522,8 +1517,7 @@ static void langwell_udc_stop(struct langwell_udc *dev)
 
 
 /* stop all USB activities */
-static void stop_activity(struct langwell_udc *dev,
-		struct usb_gadget_driver *driver)
+static void stop_activity(struct langwell_udc *dev)
 {
 	struct langwell_ep	*ep;
 	dev_dbg(&dev->pdev->dev, "---> %s()\n", __func__);
@@ -1535,9 +1529,9 @@ static void stop_activity(struct langwell_udc *dev,
 	}
 
 	/* report disconnect; the driver is already quiesced */
-	if (driver) {
+	if (dev->driver) {
 		spin_unlock(&dev->lock);
-		driver->disconnect(&dev->gadget);
+		dev->driver->disconnect(&dev->gadget);
 		spin_lock(&dev->lock);
 	}
 
@@ -1925,11 +1919,10 @@ static int langwell_stop(struct usb_gadget *g,
 
 	/* stop all usb activities */
 	dev->gadget.speed = USB_SPEED_UNKNOWN;
-	stop_activity(dev, driver);
-	spin_unlock_irqrestore(&dev->lock, flags);
-
 	dev->gadget.dev.driver = NULL;
 	dev->driver = NULL;
+	stop_activity(dev);
+	spin_unlock_irqrestore(&dev->lock, flags);
 
 	device_remove_file(&dev->pdev->dev, &dev_attr_function);
 
@@ -2315,13 +2308,9 @@ static void handle_setup_packet(struct langwell_udc *dev,
 
 			if (!gadget_is_otg(&dev->gadget))
 				break;
-			else if (setup->bRequest == USB_DEVICE_B_HNP_ENABLE) {
+			else if (setup->bRequest == USB_DEVICE_B_HNP_ENABLE)
 				dev->gadget.b_hnp_enable = 1;
-#ifdef	OTG_TRANSCEIVER
-				if (!dev->lotg->otg.default_a)
-					dev->lotg->hsm.b_hnp_enable = 1;
-#endif
-			} else if (setup->bRequest == USB_DEVICE_A_HNP_SUPPORT)
+			else if (setup->bRequest == USB_DEVICE_A_HNP_SUPPORT)
 				dev->gadget.a_hnp_support = 1;
 			else if (setup->bRequest ==
 					USB_DEVICE_A_ALT_HNP_SUPPORT)
@@ -2733,7 +2722,7 @@ static void handle_usb_reset(struct langwell_udc *dev)
 		dev->bus_reset = 1;
 
 		/* reset all the queues, stop all USB activities */
-		stop_activity(dev, dev->driver);
+		stop_activity(dev);
 		dev->usb_state = USB_STATE_DEFAULT;
 	} else {
 		dev_vdbg(&dev->pdev->dev, "device controller reset\n");
@@ -2741,7 +2730,7 @@ static void handle_usb_reset(struct langwell_udc *dev)
 		langwell_udc_reset(dev);
 
 		/* reset all the queues, stop all USB activities */
-		stop_activity(dev, dev->driver);
+		stop_activity(dev);
 
 		/* reset ep0 dQH and endptctrl */
 		ep0_reset(dev);
@@ -2752,12 +2741,6 @@ static void handle_usb_reset(struct langwell_udc *dev)
 		dev->usb_state = USB_STATE_ATTACHED;
 	}
 
-#ifdef	OTG_TRANSCEIVER
-	/* refer to USB OTG 6.6.2.3 b_hnp_en is cleared */
-	if (!dev->lotg->otg.default_a)
-		dev->lotg->hsm.b_hnp_enable = 0;
-#endif
-
 	dev_vdbg(&dev->pdev->dev, "<--- %s()\n", __func__);
 }
 
@@ -2770,29 +2753,6 @@ static void handle_bus_suspend(struct langwell_udc *dev)
 	dev->resume_state = dev->usb_state;
 	dev->usb_state = USB_STATE_SUSPENDED;
 
-#ifdef	OTG_TRANSCEIVER
-	if (dev->lotg->otg.default_a) {
-		if (dev->lotg->hsm.b_bus_suspend_vld == 1) {
-			dev->lotg->hsm.b_bus_suspend = 1;
-			/* notify transceiver the state changes */
-			if (spin_trylock(&dev->lotg->wq_lock)) {
-				langwell_update_transceiver();
-				spin_unlock(&dev->lotg->wq_lock);
-			}
-		}
-		dev->lotg->hsm.b_bus_suspend_vld++;
-	} else {
-		if (!dev->lotg->hsm.a_bus_suspend) {
-			dev->lotg->hsm.a_bus_suspend = 1;
-			/* notify transceiver the state changes */
-			if (spin_trylock(&dev->lotg->wq_lock)) {
-				langwell_update_transceiver();
-				spin_unlock(&dev->lotg->wq_lock);
-			}
-		}
-	}
-#endif
-
 	/* report suspend to the driver */
 	if (dev->driver) {
 		if (dev->driver->suspend) {
@@ -2823,11 +2783,6 @@ static void handle_bus_resume(struct langwell_udc *dev)
 	if (dev->pdev->device != 0x0829)
 		langwell_phy_low_power(dev, 0);
 
-#ifdef	OTG_TRANSCEIVER
-	if (dev->lotg->otg.default_a == 0)
-		dev->lotg->hsm.a_bus_suspend = 0;
-#endif
-
 	/* report resume to the driver */
 	if (dev->driver) {
 		if (dev->driver->resume) {
@@ -3020,7 +2975,6 @@ static void langwell_udc_remove(struct pci_dev *pdev)
 
 	dev->done = &done;
 
-#ifndef	OTG_TRANSCEIVER
 	/* free dTD dma_pool and dQH */
 	if (dev->dtd_pool)
 		dma_pool_destroy(dev->dtd_pool);
@@ -3032,7 +2986,6 @@ static void langwell_udc_remove(struct pci_dev *pdev)
 	/* release SRAM caching */
 	if (dev->has_sram && dev->got_sram)
 		sram_deinit(dev);
-#endif
 
 	if (dev->status_req) {
 		kfree(dev->status_req->req.buf);
@@ -3045,7 +2998,6 @@ static void langwell_udc_remove(struct pci_dev *pdev)
 	if (dev->got_irq)
 		free_irq(pdev->irq, dev);
 
-#ifndef	OTG_TRANSCEIVER
 	if (dev->cap_regs)
 		iounmap(dev->cap_regs);
 
@@ -3055,13 +3007,6 @@ static void langwell_udc_remove(struct pci_dev *pdev)
 
 	if (dev->enabled)
 		pci_disable_device(pdev);
-#else
-	if (dev->transceiver) {
-		otg_put_transceiver(dev->transceiver);
-		dev->transceiver = NULL;
-		dev->lotg = NULL;
-	}
-#endif
 
 	dev->cap_regs = NULL;
 
@@ -3072,9 +3017,7 @@ static void langwell_udc_remove(struct pci_dev *pdev)
 	device_remove_file(&pdev->dev, &dev_attr_langwell_udc);
 	device_remove_file(&pdev->dev, &dev_attr_remote_wakeup);
 
-#ifndef	OTG_TRANSCEIVER
 	pci_set_drvdata(pdev, NULL);
-#endif
 
 	/* free dev, wait for the release() finished */
 	wait_for_completion(&done);
@@ -3089,9 +3032,7 @@ static int langwell_udc_probe(struct pci_dev *pdev,
 		const struct pci_device_id *id)
 {
 	struct langwell_udc	*dev;
-#ifndef	OTG_TRANSCEIVER
 	unsigned long		resource, len;
-#endif
 	void			__iomem *base = NULL;
 	size_t			size;
 	int			retval;
@@ -3109,16 +3050,6 @@ static int langwell_udc_probe(struct pci_dev *pdev,
 	dev->pdev = pdev;
 	dev_dbg(&dev->pdev->dev, "---> %s()\n", __func__);
 
-#ifdef	OTG_TRANSCEIVER
-	/* PCI device is already enabled by otg_transceiver driver */
-	dev->enabled = 1;
-
-	/* mem region and register base */
-	dev->region = 1;
-	dev->transceiver = otg_get_transceiver();
-	dev->lotg = otg_to_langwell(dev->transceiver);
-	base = dev->lotg->regs;
-#else
 	pci_set_drvdata(pdev, dev);
 
 	/* now all the pci goodies ... */
@@ -3139,7 +3070,6 @@ static int langwell_udc_probe(struct pci_dev *pdev,
 	dev->region = 1;
 
 	base = ioremap_nocache(resource, len);
-#endif
 	if (base == NULL) {
 		dev_err(&dev->pdev->dev, "can't map memory\n");
 		retval = -EFAULT;
@@ -3163,7 +3093,6 @@ static int langwell_udc_probe(struct pci_dev *pdev,
 	dev->got_sram = 0;
 	dev_vdbg(&dev->pdev->dev, "dev->has_sram: %d\n", dev->has_sram);
 
-#ifndef	OTG_TRANSCEIVER
 	/* enable SRAM caching if detected */
 	if (dev->has_sram && !dev->got_sram)
 		sram_init(dev);
@@ -3182,7 +3111,6 @@ static int langwell_udc_probe(struct pci_dev *pdev,
 		goto error;
 	}
 	dev->got_irq = 1;
-#endif
 
 	/* set stopped bit */
 	dev->stopped = 1;
@@ -3257,10 +3185,8 @@ static int langwell_udc_probe(struct pci_dev *pdev,
 	dev->remote_wakeup = 0;
 	dev->dev_status = 1 << USB_DEVICE_SELF_POWERED;
 
-#ifndef	OTG_TRANSCEIVER
 	/* reset device controller */
 	langwell_udc_reset(dev);
-#endif
 
 	/* initialize gadget structure */
 	dev->gadget.ops = &langwell_ops;	/* usb_gadget_ops */
@@ -3268,9 +3194,6 @@ static int langwell_udc_probe(struct pci_dev *pdev,
 	INIT_LIST_HEAD(&dev->gadget.ep_list);	/* ep_list */
 	dev->gadget.speed = USB_SPEED_UNKNOWN;	/* speed */
 	dev->gadget.max_speed = USB_SPEED_HIGH;	/* support dual speed */
-#ifdef	OTG_TRANSCEIVER
-	dev->gadget.is_otg = 1;			/* support otg mode */
-#endif
 
 	/* the "gadget" abstracts/virtualizes the controller */
 	dev_set_name(&dev->gadget.dev, "gadget");
@@ -3282,10 +3205,8 @@ static int langwell_udc_probe(struct pci_dev *pdev,
 	/* controller endpoints reinit */
 	eps_reinit(dev);
 
-#ifndef	OTG_TRANSCEIVER
 	/* reset ep0 dQH and endptctrl */
 	ep0_reset(dev);
-#endif
 
 	/* create dTD dma_pool resource */
 	dev->dtd_pool = dma_pool_create("langwell_dtd",
@@ -3367,7 +3288,7 @@ static int langwell_udc_suspend(struct pci_dev *pdev, pm_message_t state)
 
 	spin_lock_irq(&dev->lock);
 	/* stop all usb activities */
-	stop_activity(dev, dev->driver);
+	stop_activity(dev);
 	spin_unlock_irq(&dev->lock);
 
 	/* free dTD dma_pool and dQH */
@@ -3525,22 +3446,14 @@ static struct pci_driver langwell_pci_driver = {
 
 static int __init init(void)
 {
-#ifdef	OTG_TRANSCEIVER
-	return langwell_register_peripheral(&langwell_pci_driver);
-#else
 	return pci_register_driver(&langwell_pci_driver);
-#endif
 }
 module_init(init);
 
 
 static void __exit cleanup(void)
 {
-#ifdef	OTG_TRANSCEIVER
-	return langwell_unregister_peripheral(&langwell_pci_driver);
-#else
 	pci_unregister_driver(&langwell_pci_driver);
-#endif
 }
 module_exit(cleanup);
 

drivers/usb/gadget/langwell_udc.h

@@ -8,7 +8,6 @@
  */
 
 #include <linux/usb/langwell_udc.h>
-#include <linux/usb/langwell_otg.h>
 
 /*-------------------------------------------------------------------------*/
 

drivers/usb/gadget/storage_common.c

@@ -598,16 +598,16 @@ static __maybe_unused struct usb_ss_cap_descriptor fsg_ss_cap_desc = {
 		| USB_5GBPS_OPERATION),
 	.bFunctionalitySupport = USB_LOW_SPEED_OPERATION,
 	.bU1devExitLat =	USB_DEFAULT_U1_DEV_EXIT_LAT,
-	.bU2DevExitLat =	USB_DEFAULT_U2_DEV_EXIT_LAT,
+	.bU2DevExitLat =	cpu_to_le16(USB_DEFAULT_U2_DEV_EXIT_LAT),
 };
 
 static __maybe_unused struct usb_bos_descriptor fsg_bos_desc = {
 	.bLength =		USB_DT_BOS_SIZE,
 	.bDescriptorType =	USB_DT_BOS,
 
-	.wTotalLength =		USB_DT_BOS_SIZE
+	.wTotalLength =		cpu_to_le16(USB_DT_BOS_SIZE
 				+ USB_DT_USB_EXT_CAP_SIZE
-				+ USB_DT_USB_SS_CAP_SIZE,
+				+ USB_DT_USB_SS_CAP_SIZE),
 
 	.bNumDeviceCaps =	2,
 };

drivers/usb/musb/davinci.c

@@ -33,9 +33,6 @@
 #include <linux/platform_device.h>
 #include <linux/dma-mapping.h>
 
-#include <mach/hardware.h>
-#include <mach/memory.h>
-#include <asm/gpio.h>
 #include <mach/cputype.h>
 
 #include <asm/mach-types.h>

drivers/usb/musb/musb_core.c

@@ -981,6 +981,9 @@ static void musb_shutdown(struct platform_device *pdev)
 	unsigned long	flags;
 
 	pm_runtime_get_sync(musb->controller);
+
+	musb_gadget_cleanup(musb);
+
 	spin_lock_irqsave(&musb->lock, flags);
 	musb_platform_disable(musb);
 	musb_generic_disable(musb);
@@ -1827,8 +1830,6 @@ static void musb_free(struct musb *musb)
 	sysfs_remove_group(&musb->controller->kobj, &musb_attr_group);
 #endif
 
-	musb_gadget_cleanup(musb);
-
 	if (musb->nIrq >= 0) {
 		if (musb->irq_wake)
 			disable_irq_wake(musb->nIrq);

drivers/usb/musb/omap2430.c

@@ -222,7 +222,6 @@ static inline void omap2430_low_level_init(struct musb *musb)
 	musb_writel(musb->mregs, OTG_FORCESTDBY, l);
 }
 
-/* blocking notifier support */
 static int musb_otg_notifications(struct notifier_block *nb,
 		unsigned long event, void *unused)
 {
@@ -231,7 +230,7 @@ static int musb_otg_notifications(struct notifier_block *nb,
 	musb->xceiv_event = event;
 	schedule_work(&musb->otg_notifier_work);
 
-	return 0;
+	return NOTIFY_OK;
 }
 
 static void musb_otg_notifier_work(struct work_struct *data_notifier_work)
@@ -386,6 +385,7 @@ static void omap2430_musb_disable(struct musb *musb)
 static int omap2430_musb_exit(struct musb *musb)
 {
 	del_timer_sync(&musb_idle_timer);
+	cancel_work_sync(&musb->otg_notifier_work);
 
 	omap2430_low_level_exit(musb);
 	otg_put_transceiver(musb->xceiv);

drivers/usb/otg/Kconfig

@@ -86,20 +86,6 @@ config NOP_USB_XCEIV
 	  built-in with usb ip or which are autonomous and doesn't require any
 	  phy programming such as ISP1x04 etc.
 
-config USB_LANGWELL_OTG
-	tristate "Intel Langwell USB OTG dual-role support"
-	depends on USB && PCI && INTEL_SCU_IPC
-	select USB_OTG
-	select USB_OTG_UTILS
-	help
-	  Say Y here if you want to build Intel Langwell USB OTG
-	  transciever driver in kernel. This driver implements role
-	  switch between EHCI host driver and Langwell USB OTG
-	  client driver.
-
-	  To compile this driver as a module, choose M here: the
-	  module will be called langwell_otg.
-
 config USB_MSM_OTG
 	tristate "OTG support for Qualcomm on-chip USB controller"
 	depends on (USB || USB_GADGET) && ARCH_MSM
@@ -124,7 +110,7 @@ config AB8500_USB
 
 config FSL_USB2_OTG
 	bool "Freescale USB OTG Transceiver Driver"
-	depends on USB_EHCI_FSL && USB_GADGET_FSL_USB2
+	depends on USB_EHCI_FSL && USB_GADGET_FSL_USB2 && USB_SUSPEND
 	select USB_OTG
 	select USB_OTG_UTILS
 	help
@@ -132,7 +118,7 @@ config FSL_USB2_OTG
 
 config USB_MV_OTG
 	tristate "Marvell USB OTG support"
-	depends on USB_MV_UDC
+	depends on USB_MV_UDC && USB_SUSPEND
 	select USB_OTG
 	select USB_OTG_UTILS
 	help

drivers/usb/otg/Makefile

@@ -13,7 +13,6 @@ obj-$(CONFIG_USB_GPIO_VBUS)	+= gpio_vbus.o
 obj-$(CONFIG_ISP1301_OMAP)	+= isp1301_omap.o
 obj-$(CONFIG_TWL4030_USB)	+= twl4030-usb.o
 obj-$(CONFIG_TWL6030_USB)	+= twl6030-usb.o
-obj-$(CONFIG_USB_LANGWELL_OTG)	+= langwell_otg.o
 obj-$(CONFIG_NOP_USB_XCEIV)	+= nop-usb-xceiv.o
 obj-$(CONFIG_USB_ULPI)		+= ulpi.o
 obj-$(CONFIG_USB_ULPI_VIEWPORT)	+= ulpi_viewport.o

drivers/usb/renesas_usbhs/mod_gadget.c

@@ -425,7 +425,7 @@ static int usbhsg_recip_run_handle(struct usbhs_priv *priv,
 	struct usbhs_pipe *pipe;
 	int recip = ctrl->bRequestType & USB_RECIP_MASK;
 	int nth = le16_to_cpu(ctrl->wIndex) & USB_ENDPOINT_NUMBER_MASK;
-	int ret;
+	int ret = 0;
 	int (*func)(struct usbhs_priv *priv, struct usbhsg_uep *uep,
 		    struct usb_ctrlrequest *ctrl);
 	char *msg;

include/linux/usb/langwell_otg.h

-/*
- * Intel Langwell USB OTG transceiver driver
- * Copyright (C) 2008 - 2010, Intel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms and conditions of the GNU General Public License,
- * version 2, as published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
- * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program; if not, write to the Free Software Foundation, Inc.,
- * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
- *
- */
-
-#ifndef __LANGWELL_OTG_H
-#define __LANGWELL_OTG_H
-
-#include <linux/usb/intel_mid_otg.h>
-
-#define CI_USBCMD		0x30
-#	define USBCMD_RST		BIT(1)
-#	define USBCMD_RS		BIT(0)
-#define CI_USBSTS		0x34
-#	define USBSTS_SLI		BIT(8)
-#	define USBSTS_URI		BIT(6)
-#	define USBSTS_PCI		BIT(2)
-#define CI_PORTSC1		0x74
-#	define PORTSC_PP		BIT(12)
-#	define PORTSC_LS		(BIT(11) | BIT(10))
-#	define PORTSC_SUSP		BIT(7)
-#	define PORTSC_CCS		BIT(0)
-#define CI_HOSTPC1		0xb4
-#	define HOSTPC1_PHCD		BIT(22)
-#define CI_OTGSC		0xf4
-#	define OTGSC_DPIE		BIT(30)
-#	define OTGSC_1MSE		BIT(29)
-#	define OTGSC_BSEIE		BIT(28)
-#	define OTGSC_BSVIE		BIT(27)
-#	define OTGSC_ASVIE		BIT(26)
-#	define OTGSC_AVVIE		BIT(25)
-#	define OTGSC_IDIE		BIT(24)
-#	define OTGSC_DPIS		BIT(22)
-#	define OTGSC_1MSS		BIT(21)
-#	define OTGSC_BSEIS		BIT(20)
-#	define OTGSC_BSVIS		BIT(19)
-#	define OTGSC_ASVIS		BIT(18)
-#	define OTGSC_AVVIS		BIT(17)
-#	define OTGSC_IDIS		BIT(16)
-#	define OTGSC_DPS		BIT(14)
-#	define OTGSC_1MST		BIT(13)
-#	define OTGSC_BSE		BIT(12)
-#	define OTGSC_BSV		BIT(11)
-#	define OTGSC_ASV		BIT(10)
-#	define OTGSC_AVV		BIT(9)
-#	define OTGSC_ID			BIT(8)
-#	define OTGSC_HABA		BIT(7)
-#	define OTGSC_HADP		BIT(6)
-#	define OTGSC_IDPU		BIT(5)
-#	define OTGSC_DP			BIT(4)
-#	define OTGSC_OT			BIT(3)
-#	define OTGSC_HAAR		BIT(2)
-#	define OTGSC_VC			BIT(1)
-#	define OTGSC_VD			BIT(0)
-#	define OTGSC_INTEN_MASK		(0x7f << 24)
-#	define OTGSC_INT_MASK		(0x5f << 24)
-#	define OTGSC_INTSTS_MASK	(0x7f << 16)
-#define CI_USBMODE		0xf8
-#	define USBMODE_CM		(BIT(1) | BIT(0))
-#	define USBMODE_IDLE		0
-#	define USBMODE_DEVICE		0x2
-#	define USBMODE_HOST		0x3
-#define USBCFG_ADDR			0xff10801c
-#define USBCFG_LEN			4
-#	define USBCFG_VBUSVAL		BIT(14)
-#	define USBCFG_AVALID		BIT(13)
-#	define USBCFG_BVALID		BIT(12)
-#	define USBCFG_SESEND		BIT(11)
-
-#define INTR_DUMMY_MASK (USBSTS_SLI | USBSTS_URI | USBSTS_PCI)
-
-enum langwell_otg_timer_type {
-	TA_WAIT_VRISE_TMR,
-	TA_WAIT_BCON_TMR,
-	TA_AIDL_BDIS_TMR,
-	TB_ASE0_BRST_TMR,
-	TB_SE0_SRP_TMR,
-	TB_SRP_INIT_TMR,
-	TB_SRP_FAIL_TMR,
-	TB_BUS_SUSPEND_TMR
-};
-
-#define TA_WAIT_VRISE	100
-#define TA_WAIT_BCON	30000
-#define TA_AIDL_BDIS	15000
-#define TB_ASE0_BRST	5000
-#define TB_SE0_SRP	2
-#define TB_SRP_INIT	100
-#define TB_SRP_FAIL	5500
-#define TB_BUS_SUSPEND	500
-
-struct langwell_otg_timer {
-	unsigned long expires;	/* Number of count increase to timeout */
-	unsigned long count;	/* Tick counter */
-	void (*function)(unsigned long);	/* Timeout function */
-	unsigned long data;	/* Data passed to function */
-	struct list_head list;
-};
-
-struct langwell_otg {
-	struct intel_mid_otg_xceiv	iotg;
-	struct device			*dev;
-
-	void __iomem			*usbcfg;	/* SCCBUSB config Reg */
-
-	unsigned			region;
-	unsigned			cfg_region;
-
-	struct work_struct		work;
-	struct workqueue_struct		*qwork;
-	struct timer_list		hsm_timer;
-
-	spinlock_t			lock;
-	spinlock_t			wq_lock;
-
-	struct notifier_block		iotg_notifier;
-};
-
-static inline
-struct langwell_otg *mid_xceiv_to_lnw(struct intel_mid_otg_xceiv *iotg)
-{
-	return container_of(iotg, struct langwell_otg, iotg);
-}
-
-#endif /* __LANGWELL_OTG_H__ */