Commit 7cbeb2e1 authored by Sakari Ailus's avatar Sakari Ailus Committed by Mauro Carvalho Chehab

media: smiapp: Move definitions under driver directory

include/media/i2c/smiapp.h was meant to serve systems where the sensor is
enumerated through platform data. That's no longer necessary, hopefully
not even in out-of-tree use cases. Move the definitions to the appropriate
headers.
Signed-off-by: default avatarSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: default avatarMauro Carvalho Chehab <mchehab+samsung@kernel.org>
parent 354d5aba
......@@ -35,6 +35,10 @@
#define SMIAPP_FLASH_MODE_CAPABILITY_SINGLE_STROBE BIT(0)
#define SMIAPP_FLASH_MODE_CAPABILITY_MULTIPLE_STROBE BIT(1)
#define SMIAPP_CSI_SIGNALLING_MODE_CCP2_DATA_CLOCK 0
#define SMIAPP_CSI_SIGNALLING_MODE_CCP2_DATA_STROBE 1
#define SMIAPP_CSI_SIGNALLING_MODE_CSI2 2
#define SMIAPP_DPHY_CTRL_AUTOMATIC 0
/* DPHY control based on REQUESTED_LINK_BIT_RATE_MBPS */
#define SMIAPP_DPHY_CTRL_UI 1
......
......@@ -14,7 +14,6 @@
#include <linux/mutex.h>
#include <media/v4l2-ctrls.h>
#include <media/v4l2-subdev.h>
#include <media/i2c/smiapp.h>
#include "smiapp-pll.h"
#include "smiapp-reg.h"
......@@ -42,6 +41,49 @@
#define SMIAPP_COLOUR_COMPONENTS 4
#define SMIAPP_NAME "smiapp"
#define SMIAPP_DFL_I2C_ADDR (0x20 >> 1) /* Default I2C Address */
#define SMIAPP_ALT_I2C_ADDR (0x6e >> 1) /* Alternate I2C Address */
/*
* Sometimes due to board layout considerations the camera module can be
* mounted rotated. The typical rotation used is 180 degrees which can be
* corrected by giving a default H-FLIP and V-FLIP in the sensor readout.
* FIXME: rotation also changes the bayer pattern.
*/
enum smiapp_module_board_orient {
SMIAPP_MODULE_BOARD_ORIENT_0 = 0,
SMIAPP_MODULE_BOARD_ORIENT_180,
};
struct smiapp_flash_strobe_parms {
u8 mode;
u32 strobe_width_high_us;
u16 strobe_delay;
u16 stobe_start_point;
u8 trigger;
};
struct smiapp_hwconfig {
/*
* Change the cci address if i2c_addr_alt is set.
* Both default and alternate cci addr need to be present
*/
unsigned short i2c_addr_dfl; /* Default i2c addr */
unsigned short i2c_addr_alt; /* Alternate i2c addr */
uint32_t ext_clk; /* sensor external clk */
unsigned int lanes; /* Number of CSI-2 lanes */
uint32_t csi_signalling_mode; /* SMIAPP_CSI_SIGNALLING_MODE_* */
uint64_t *op_sys_clock;
enum smiapp_module_board_orient module_board_orient;
struct smiapp_flash_strobe_parms *strobe_setup;
};
#include "smiapp-limits.h"
struct smiapp_quirk;
......
/* SPDX-License-Identifier: GPL-2.0-only */
/*
* include/media/i2c/smiapp.h
*
* Generic driver for SMIA/SMIA++ compliant camera modules
*
* Copyright (C) 2011--2012 Nokia Corporation
* Contact: Sakari Ailus <sakari.ailus@iki.fi>
*/
#ifndef __SMIAPP_H_
#define __SMIAPP_H_
#include <media/v4l2-subdev.h>
#define SMIAPP_NAME "smiapp"
#define SMIAPP_DFL_I2C_ADDR (0x20 >> 1) /* Default I2C Address */
#define SMIAPP_ALT_I2C_ADDR (0x6e >> 1) /* Alternate I2C Address */
#define SMIAPP_CSI_SIGNALLING_MODE_CCP2_DATA_CLOCK 0
#define SMIAPP_CSI_SIGNALLING_MODE_CCP2_DATA_STROBE 1
#define SMIAPP_CSI_SIGNALLING_MODE_CSI2 2
/*
* Sometimes due to board layout considerations the camera module can be
* mounted rotated. The typical rotation used is 180 degrees which can be
* corrected by giving a default H-FLIP and V-FLIP in the sensor readout.
* FIXME: rotation also changes the bayer pattern.
*/
enum smiapp_module_board_orient {
SMIAPP_MODULE_BOARD_ORIENT_0 = 0,
SMIAPP_MODULE_BOARD_ORIENT_180,
};
struct smiapp_flash_strobe_parms {
u8 mode;
u32 strobe_width_high_us;
u16 strobe_delay;
u16 stobe_start_point;
u8 trigger;
};
struct smiapp_hwconfig {
/*
* Change the cci address if i2c_addr_alt is set.
* Both default and alternate cci addr need to be present
*/
unsigned short i2c_addr_dfl; /* Default i2c addr */
unsigned short i2c_addr_alt; /* Alternate i2c addr */
uint32_t ext_clk; /* sensor external clk */
unsigned int lanes; /* Number of CSI-2 lanes */
uint32_t csi_signalling_mode; /* SMIAPP_CSI_SIGNALLING_MODE_* */
uint64_t *op_sys_clock;
enum smiapp_module_board_orient module_board_orient;
struct smiapp_flash_strobe_parms *strobe_setup;
};
#endif /* __SMIAPP_H_ */
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment