Commit 7d0d3fa7 authored by Linus Torvalds's avatar Linus Torvalds

Merge tag 'arm-boardfiles-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM boardfile deprecation from Arnd Bergmann:
 "Over the past ten years, new machine support was based on device tree,
  and an initial set of about 400 boards using ATAGS with boardfile for
  booting were grandfathered in, with about half of them either removed
  or converted to DT over time.

  Based on the recent mailing list discussion I started, I have now
  turned the findings into a set of patches that marks most board files
  as 'depends on UNUSED_BOARD_FILES', leaving only 38 of the 196 boards.

  For the boards that are marked as unused, there are two final chances
  for potential users: The removal is scheduled to take place after the
  longterm stable kernel at the end of 2022, so users can stay on that
  version for another few years, and if anyone still has one of these
  machines and is planning to keep updating kernels beyond that version,
  they can speak up now to have their boards taken off the list again.

  Waiting for the LTS release also makes sure that there will be at
  least one longterm kernel that contains the recent multiplatform
  conversion along while still supporting all legacy boards.

  The short summary of the current status is:

   - The s3c24xx, cns3xxx, iop32x and mv78xx0 platforms have no known
     users and will be removed entirely.

   - The mmp and davinci platforms have DT support for the important
     machines and will become DT-only after this.

   - s3c64xx, dove, orion5x, and pxa keep some board files to allow
     those to be migrated over to DT more easily, but most board files
     are getting removed now. DT support on these platforms is partially
     working but requires changes to additional drivers for the other
     boards.

   - omap1, ep93xx, sa1100, footbridge and rpc have no DT support at the
     moment but have some boards with known users. Removing the board
     files that nobody uses should make it easier to try a DT conversion
     if anyone cares.

  There is no explicit timeline what happens with the boards that remain
  after this removal, but I expect to revisit this in the future, and
  with most boards gone, there will be a good time to do a treewide
  review of platform drivers that never gained DT support and have no
  remaining in-tree board files"

Link: https://lore.kernel.org/linux-arm-kernel/CAK8P3a0Z9vGEQbVRBo84bSyPFM-LF+hs5w8ZA51g2Z+NsdtDQA@mail.gmail.com/

* tag 'arm-boardfiles-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  ARM: cns3xxx: add CONFIG_UNUSED_BOARD_FILES dependency
  ARM: iop32x: mark as unused
  ARM: s3c: mark most board files as unused
  ARM: omap1: add Kconfig dependencies for unused boards
  ARM: sa1100: mark most boards as unused
  ARM: footbridge: mark cats board for removal
  ARM: mmp: mark all board files for removal
  ARM: ep93xx: mark most board files as unused
  ARM: davinci: mark all ATAGS board files as unused
  ARM: orion: add ATAGS dependencies
  ARM: pxa: add Kconfig dependencies for ATAGS based boards
  ARM: add CONFIG_UNUSED_BOARD_FILES
  ARM: add ATAGS dependencies to non-DT platforms
parents dd65b964 1785ab76
......@@ -350,6 +350,7 @@ config ARCH_MULTIPLATFORM
config ARCH_FOOTBRIDGE
bool "FootBridge"
depends on CPU_LITTLE_ENDIAN
depends on ATAGS
select CPU_SA110
select FOOTBRIDGE
select NEED_MACH_MEMORY_H
......@@ -361,6 +362,7 @@ config ARCH_RPC
bool "RiscPC"
depends on !CC_IS_CLANG && GCC_VERSION < 90100 && GCC_VERSION >= 60000
depends on CPU_LITTLE_ENDIAN
depends on ATAGS
select ARCH_ACORN
select ARCH_MAY_HAVE_PC_FDC
select ARCH_SPARSEMEM_ENABLE
......@@ -380,6 +382,7 @@ config ARCH_RPC
config ARCH_SA1100
bool "SA1100-based"
depends on CPU_LITTLE_ENDIAN
depends on ATAGS
select ARCH_MTD_XIP
select ARCH_SPARSEMEM_ENABLE
select CLKSRC_MMIO
......@@ -1541,14 +1544,26 @@ config USE_OF
Include support for flattened device tree machine descriptions.
config ATAGS
bool "Support for the traditional ATAGS boot data passing" if USE_OF
bool "Support for the traditional ATAGS boot data passing"
default y
help
This is the traditional way of passing data to the kernel at boot
time. If you are solely relying on the flattened device tree (or
the ARM_ATAG_DTB_COMPAT option) then you may unselect this option
to remove ATAGS support from your kernel binary. If unsure,
leave this to y.
to remove ATAGS support from your kernel binary.
config UNUSED_BOARD_FILES
bool "Board support for machines without known users"
depends on ATAGS
help
Most ATAGS based board files are completely unused and are
scheduled for removal in early 2023, and left out of kernels
by default now. If you are using a board file that is marked
as unused, turn on this option to build support into the kernel.
To keep support for your individual board from being removed,
send a reply to the email discussion at
https://lore.kernel.org/all/CAK8P3a0Z9vGEQbVRBo84bSyPFM-LF+hs5w8ZA51g2Z+NsdtDQA@mail.gmail.com/
config DEPRECATED_PARAM_STRUCT
bool "Provide old way to pass kernel parameters"
......
......@@ -2,6 +2,7 @@ CONFIG_LOG_BUF_SHIFT=14
CONFIG_EXPERT=y
CONFIG_ARCH_SA1100=y
CONFIG_SA1100_BADGE4=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="init=/linuxrc root=/dev/mtdblock3"
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_FPE_NWFPE=y
......
......@@ -4,6 +4,7 @@ CONFIG_LOG_BUF_SHIFT=14
CONFIG_ARCH_SA1100=y
CONFIG_SA1100_CERF=y
CONFIG_SA1100_CERF_FLASH_16MB=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="console=ttySA0,38400 root=/dev/mtdblock3 rootfstype=jffs2 rw mem=32M init=/linuxrc"
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_USERSPACE=m
......
......@@ -12,6 +12,7 @@ CONFIG_ARCH_PXA=y
CONFIG_MACH_CM_X300=y
CONFIG_AEABI=y
CONFIG_HIGHMEM=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="root=/dev/mtdblock5 rootfstype=ubifs console=ttyS2,38400"
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y
......
......@@ -12,6 +12,7 @@ CONFIG_PROFILING=y
CONFIG_ARCH_MULTI_V6=y
CONFIG_ARCH_CNS3XXX=y
CONFIG_MACH_CNS3420VB=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="console=ttyS0,38400 mem=128M root=/dev/mmcblk0p1 ro rootwait"
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
......
......@@ -14,6 +14,7 @@ CONFIG_KALLSYMS_EXTRA_PASS=y
CONFIG_ARCH_PXA=y
CONFIG_MACH_COLIBRI=y
CONFIG_AEABI=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
......
......@@ -2,6 +2,7 @@
CONFIG_ARCH_PXA=y
CONFIG_MACH_COLIBRI300=y
CONFIG_AEABI=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="console=ttyS0,115200 rw"
CONFIG_CPU_IDLE=y
CONFIG_FPE_NWFPE=y
......
......@@ -13,6 +13,7 @@ CONFIG_MACH_POODLE=y
CONFIG_MACH_CORGI=y
CONFIG_MACH_SHEPHERD=y
CONFIG_MACH_HUSKY=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="console=ttyS0,115200n8 console=tty1 noinitrd root=/dev/mtdblock2 rootfstype=jffs2 debug"
CONFIG_FPE_NWFPE=y
CONFIG_BINFMT_AOUT=m
......
......@@ -14,17 +14,8 @@ CONFIG_ARCH_MULTIPLATFORM=y
CONFIG_ARCH_MULTI_V5=y
# CONFIG_ARCH_MULTI_V7 is not set
CONFIG_ARCH_DAVINCI=y
CONFIG_ARCH_DAVINCI_DM644x=y
CONFIG_ARCH_DAVINCI_DM355=y
CONFIG_ARCH_DAVINCI_DM646x=y
CONFIG_ARCH_DAVINCI_DA830=y
CONFIG_ARCH_DAVINCI_DA850=y
CONFIG_ARCH_DAVINCI_DM365=y
CONFIG_MACH_SFFSDR=y
CONFIG_MACH_NEUROS_OSD2=y
CONFIG_MACH_DM355_LEOPARD=y
CONFIG_MACH_MITYOMAPL138=y
CONFIG_MACH_OMAPL138_HAWKBOARD=y
CONFIG_DAVINCI_MUX_DEBUG=y
CONFIG_DAVINCI_MUX_WARNINGS=y
CONFIG_AEABI=y
......@@ -110,7 +101,6 @@ CONFIG_KEYBOARD_XTKBD=m
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PWM_BEEPER=m
CONFIG_INPUT_DM355EVM=m
CONFIG_SERIO_LIBPS2=y
# CONFIG_VT_CONSOLE is not set
CONFIG_SERIAL_8250=y
......@@ -138,7 +128,6 @@ CONFIG_SYSCON_REBOOT_MODE=m
CONFIG_BATTERY_LEGO_EV3=m
CONFIG_WATCHDOG=y
CONFIG_DAVINCI_WATCHDOG=y
CONFIG_MFD_DM355EVM_MSP=y
CONFIG_TPS6507X=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
......
......@@ -8,7 +8,6 @@ CONFIG_EXPERT=y
CONFIG_ARCH_MULTI_V4T=y
# CONFIG_ARCH_MULTI_V7 is not set
CONFIG_ARCH_EP93XX=y
CONFIG_MACH_ADSSPHERE=y
CONFIG_MACH_EDB9301=y
CONFIG_MACH_EDB9302=y
CONFIG_MACH_EDB9302A=y
......@@ -17,13 +16,6 @@ CONFIG_MACH_EDB9307A=y
CONFIG_MACH_EDB9312=y
CONFIG_MACH_EDB9315=y
CONFIG_MACH_EDB9315A=y
CONFIG_MACH_GESBC9312=y
CONFIG_MACH_MICRO9H=y
CONFIG_MACH_MICRO9M=y
CONFIG_MACH_MICRO9L=y
CONFIG_MACH_MICRO9S=y
CONFIG_MACH_SIM_ONE=y
CONFIG_MACH_SNAPPER_CL15=y
CONFIG_MACH_TS72XX=y
CONFIG_MACH_VISION_EP9307=y
CONFIG_AEABI=y
......
......@@ -8,6 +8,7 @@ CONFIG_ARCH_PXA=y
CONFIG_ARCH_PXA_ESERIES=y
CONFIG_IWMMXT=y
CONFIG_AEABI=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_KEXEC=y
CONFIG_FPE_NWFPE=y
CONFIG_MODULES=y
......
......@@ -15,6 +15,7 @@ CONFIG_EXPERT=y
CONFIG_ARCH_PXA=y
CONFIG_PXA_EZX=y
CONFIG_AEABI=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="console=tty1 root=/dev/mmcblk0p2 rootfstype=ext2 rootdelay=3 ip=192.168.0.202:192.168.0.200:192.168.0.200:255.255.255.0 debug"
CONFIG_KEXEC=y
CONFIG_CPU_FREQ=y
......
......@@ -5,7 +5,6 @@ CONFIG_BLK_DEV_INITRD=y
CONFIG_EXPERT=y
# CONFIG_HOTPLUG is not set
CONFIG_ARCH_FOOTBRIDGE=y
CONFIG_ARCH_CATS=y
CONFIG_ARCH_EBSA285_HOST=y
CONFIG_ARCH_NETWINDER=y
CONFIG_FPE_NWFPE=y
......
......@@ -10,6 +10,7 @@ CONFIG_EXPERT=y
CONFIG_ARCH_PXA=y
CONFIG_MACH_H5000=y
CONFIG_AEABI=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="keepinitrd"
CONFIG_KEXEC=y
CONFIG_FPE_NWFPE=y
......
......@@ -3,6 +3,7 @@ CONFIG_LOG_BUF_SHIFT=14
CONFIG_BLK_DEV_INITRD=y
CONFIG_ARCH_SA1100=y
CONFIG_SA1100_HACKKIT=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="console=ttySA0,115200 root=/dev/ram0 initrd=0xc0400000,8M init=/rootshell"
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_FPE_NWFPE=y
......
......@@ -9,6 +9,7 @@ CONFIG_MACH_GLANTANK=y
CONFIG_ARCH_IQ80321=y
CONFIG_ARCH_IQ31244=y
CONFIG_MACH_N2100=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="console=ttyS0,115200 root=/dev/nfs ip=bootp cachepolicy=writealloc"
CONFIG_FPE_NWFPE=y
CONFIG_BINFMT_AOUT=y
......
......@@ -4,6 +4,7 @@ CONFIG_SYSFS_DEPRECATED_V2=y
CONFIG_ARCH_SA1100=y
CONFIG_SA1100_JORNADA720=y
CONFIG_SA1100_JORNADA720_SSP=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_FPE_NWFPE=y
CONFIG_BINFMT_AOUT=y
CONFIG_PM=y
......
......@@ -3,6 +3,7 @@ CONFIG_LOG_BUF_SHIFT=14
CONFIG_BLK_DEV_INITRD=y
CONFIG_ARCH_SA1100=y
CONFIG_SA1100_LART=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="console=ttySA0,9600 root=/dev/ram"
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y
......
......@@ -3,6 +3,7 @@ CONFIG_LOG_BUF_SHIFT=14
# CONFIG_ARCH_MULTI_V7 is not set
CONFIG_ARCH_PXA=y
CONFIG_MACH_LOGICPD_PXA270=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="root=/dev/nfs ip=bootp console=ttyS0,115200 mem=64M"
CONFIG_FPE_NWFPE=y
CONFIG_MODULES=y
......
......@@ -3,6 +3,7 @@ CONFIG_LOG_BUF_SHIFT=14
# CONFIG_ARCH_MULTI_V7 is not set
CONFIG_ARCH_PXA=y
CONFIG_ARCH_LUBBOCK=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="root=/dev/nfs ip=bootp console=ttyS0,115200 mem=64M"
CONFIG_FPE_NWFPE=y
CONFIG_MODULES=y
......
......@@ -13,6 +13,7 @@ CONFIG_ARCH_PXA=y
CONFIG_MACH_H4700=y
CONFIG_MACH_MAGICIAN=y
CONFIG_AEABI=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="keepinitrd"
CONFIG_KEXEC=y
CONFIG_CPU_FREQ=y
......
......@@ -3,6 +3,7 @@ CONFIG_LOG_BUF_SHIFT=14
# CONFIG_ARCH_MULTI_V7 is not set
CONFIG_ARCH_PXA=y
CONFIG_MACH_MAINSTONE=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="root=/dev/nfs ip=bootp console=ttyS0,115200 mem=64M"
CONFIG_FPE_NWFPE=y
CONFIG_MODULES=y
......
......@@ -11,6 +11,7 @@ CONFIG_S3C_ADC=y
CONFIG_CPU_S3C2440=y
CONFIG_MACH_MINI2440=y
CONFIG_AEABI=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_KEXEC=y
CONFIG_CPU_IDLE=y
CONFIG_APM_EMULATION=y
......
......@@ -5,10 +5,8 @@ CONFIG_LOG_BUF_SHIFT=14
CONFIG_SYSFS_DEPRECATED_V2=y
# CONFIG_BLK_DEV_BSG is not set
CONFIG_ARCH_MMP=y
CONFIG_MACH_BROWNSTONE=y
CONFIG_MACH_FLINT=y
CONFIG_MACH_MARVELL_JASPER=y
CONFIG_AEABI=y
CONFIG_MACH_MMP2_DT=y
CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS2,38400 mem=128M user_debug=255 earlyprintk"
CONFIG_VFP=y
CONFIG_MODULES=y
......@@ -56,6 +54,7 @@ CONFIG_BACKLIGHT_MAX8925=y
CONFIG_MMC=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_DRV_MAX8925=y
# CONFIG_RESET_CONTROLLER is not set
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
CONFIG_EXT4_FS=y
......
......@@ -12,17 +12,8 @@ CONFIG_MACH_ASPEED_G4=y
CONFIG_ARCH_AT91=y
CONFIG_SOC_AT91SAM9=y
CONFIG_ARCH_DAVINCI=y
CONFIG_ARCH_DAVINCI_DM644x=y
CONFIG_ARCH_DAVINCI_DM355=y
CONFIG_ARCH_DAVINCI_DM646x=y
CONFIG_ARCH_DAVINCI_DA830=y
CONFIG_ARCH_DAVINCI_DA850=y
CONFIG_ARCH_DAVINCI_DM365=y
CONFIG_MACH_SFFSDR=y
CONFIG_MACH_NEUROS_OSD2=y
CONFIG_MACH_DM355_LEOPARD=y
CONFIG_MACH_MITYOMAPL138=y
CONFIG_MACH_OMAPL138_HAWKBOARD=y
CONFIG_ARCH_MXC=y
CONFIG_SOC_IMX25=y
CONFIG_SOC_IMX27=y
......@@ -31,8 +22,6 @@ CONFIG_MACH_KIRKWOOD=y
CONFIG_ARCH_NPCM=y
CONFIG_ARCH_WPCM450=y
CONFIG_ARCH_ORION5X=y
CONFIG_MACH_DB88F5281=y
CONFIG_MACH_RD88F5182=y
CONFIG_MACH_RD88F5182_DT=y
CONFIG_MACH_KUROBOX_PRO=y
CONFIG_MACH_DNS323=y
......@@ -40,18 +29,12 @@ CONFIG_MACH_TS209=y
CONFIG_MACH_TERASTATION_PRO2=y
CONFIG_MACH_LINKSTATION_PRO=y
CONFIG_MACH_LINKSTATION_MINI=y
CONFIG_MACH_LINKSTATION_LS_HGL=y
CONFIG_MACH_TS409=y
CONFIG_MACH_WRT350N_V2=y
CONFIG_MACH_TS78XX=y
CONFIG_MACH_MV2120=y
CONFIG_MACH_D2NET_DT=y
CONFIG_MACH_NET2BIG=y
CONFIG_MACH_MSS2_DT=y
CONFIG_MACH_WNR854T=y
CONFIG_MACH_RD88F5181L_GE=y
CONFIG_MACH_RD88F5181L_FXO=y
CONFIG_MACH_RD88F6183AP_GE=y
CONFIG_ARCH_SUNXI=y
CONFIG_ARCH_VERSATILE=y
CONFIG_AEABI=y
......
......@@ -17,6 +17,7 @@ CONFIG_MACH_TERASTATION_WXL=y
CONFIG_AEABI=y
CONFIG_HIGHMEM=y
CONFIG_FPE_NWFPE=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_VFP=y
CONFIG_KPROBES=y
CONFIG_MODULES=y
......
......@@ -9,8 +9,6 @@ CONFIG_PROFILING=y
CONFIG_ARCH_MVEBU=y
CONFIG_MACH_KIRKWOOD=y
CONFIG_ARCH_ORION5X=y
CONFIG_MACH_DB88F5281=y
CONFIG_MACH_RD88F5182=y
CONFIG_MACH_RD88F5182_DT=y
CONFIG_MACH_KUROBOX_PRO=y
CONFIG_MACH_DNS323=y
......@@ -19,18 +17,12 @@ CONFIG_MACH_TERASTATION_PRO2=y
CONFIG_MACH_LINKSTATION_PRO=y
CONFIG_MACH_LINKSTATION_LSCHL=y
CONFIG_MACH_LINKSTATION_MINI=y
CONFIG_MACH_LINKSTATION_LS_HGL=y
CONFIG_MACH_TS409=y
CONFIG_MACH_WRT350N_V2=y
CONFIG_MACH_TS78XX=y
CONFIG_MACH_MV2120=y
CONFIG_MACH_D2NET_DT=y
CONFIG_MACH_NET2BIG=y
CONFIG_MACH_MSS2_DT=y
CONFIG_MACH_WNR854T=y
CONFIG_MACH_RD88F5181L_GE=y
CONFIG_MACH_RD88F5181L_FXO=y
CONFIG_MACH_RD88F6183AP_GE=y
CONFIG_AEABI=y
CONFIG_HIGHMEM=y
CONFIG_ARM_APPENDED_DTB=y
......
......@@ -25,17 +25,8 @@ CONFIG_ARCH_OMAP850=y
CONFIG_ARCH_OMAP16XX=y
# CONFIG_OMAP_MUX is not set
CONFIG_OMAP_RESET_CLOCKS=y
CONFIG_MACH_OMAP_INNOVATOR=y
CONFIG_MACH_OMAP_H2=y
CONFIG_MACH_OMAP_H3=y
CONFIG_MACH_HERALD=y
CONFIG_MACH_OMAP_OSK=y
CONFIG_MACH_OMAP_PERSEUS2=y
CONFIG_MACH_OMAP_FSAMPLE=y
CONFIG_MACH_VOICEBLUE=y
CONFIG_MACH_OMAP_PALMTE=y
CONFIG_MACH_OMAP_PALMZ71=y
CONFIG_MACH_OMAP_PALMTT=y
CONFIG_MACH_SX1=y
CONFIG_MACH_NOKIA770=y
CONFIG_MACH_AMS_DELTA=y
......
......@@ -9,9 +9,6 @@ CONFIG_ARCH_MULTI_V5=y
# CONFIG_ARCH_MULTI_V6 is not set
# CONFIG_ARCH_MULTI_V7 is not set
CONFIG_ARCH_ORION5X=y
CONFIG_ARCH_ORION5X_DT=y
CONFIG_MACH_DB88F5281=y
CONFIG_MACH_RD88F5182=y
CONFIG_MACH_RD88F5182_DT=y
CONFIG_MACH_KUROBOX_PRO=y
CONFIG_MACH_DNS323=y
......@@ -19,20 +16,10 @@ CONFIG_MACH_TS209=y
CONFIG_MACH_TERASTATION_PRO2=y
CONFIG_MACH_LINKSTATION_PRO=y
CONFIG_MACH_LINKSTATION_MINI=y
CONFIG_MACH_LINKSTATION_LS_HGL=y
CONFIG_MACH_TS409=y
CONFIG_MACH_WRT350N_V2=y
CONFIG_MACH_TS78XX=y
CONFIG_MACH_MV2120=y
CONFIG_MACH_EDMINI_V2_DT=y
CONFIG_MACH_D2NET=y
CONFIG_MACH_BIGDISK=y
CONFIG_MACH_NET2BIG=y
CONFIG_MACH_MSS2=y
CONFIG_MACH_WNR854T=y
CONFIG_MACH_RD88F5181L_GE=y
CONFIG_MACH_RD88F5181L_FXO=y
CONFIG_MACH_RD88F6183AP_GE=y
CONFIG_AEABI=y
CONFIG_ARM_APPENDED_DTB=y
CONFIG_ARM_ATAG_DTB_COMPAT=y
......
......@@ -10,6 +10,7 @@ CONFIG_ARCH_PXA=y
CONFIG_ARCH_PXA_PALM=y
# CONFIG_MACH_PALMTX is not set
CONFIG_AEABI=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="mem=32M console=tty root=/dev/mmcblk0"
CONFIG_FPE_NWFPE=y
CONFIG_PM=y
......
......@@ -16,6 +16,7 @@ CONFIG_MACH_PCM027=y
CONFIG_MACH_PCM990_BASEBOARD=y
CONFIG_AEABI=y
# CONFIG_OABI_COMPAT is not set
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
......
......@@ -6,6 +6,7 @@ CONFIG_EXPERT=y
# CONFIG_SHMEM is not set
CONFIG_ARCH_SA1100=y
CONFIG_SA1100_PLEB=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="console=ttySA0,9600 mem=16M@0xc0000000 mem=16M@0xc8000000 root=/dev/ram initrd=0xc0400000,4M"
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_ONDEMAND=y
......
......@@ -3,6 +3,7 @@ CONFIG_LOG_BUF_SHIFT=14
# CONFIG_ARCH_MULTI_V7 is not set
CONFIG_ARCH_PXA=y
CONFIG_ARCH_PXA_IDP=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="root=/dev/nfs ip=dhcp console=ttyS0,115200 mem=64M"
CONFIG_FPE_NWFPE=y
CONFIG_MODULES=y
......
......@@ -7,9 +7,7 @@ CONFIG_KALLSYMS_ALL=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_ARCH_MULTI_V7 is not set
CONFIG_ARCH_PXA=y
CONFIG_MACH_LITTLETON=y
CONFIG_MACH_TAVOREVB=y
CONFIG_MACH_SAAR=y
CONFIG_MACH_PXA3XX_DT=y
CONFIG_AEABI=y
CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS0,115200 mem=64M debug"
CONFIG_FPE_NWFPE=y
......@@ -43,8 +41,6 @@ CONFIG_SMC91X=y
# CONFIG_KEYBOARD_ATKBD is not set
CONFIG_KEYBOARD_GPIO=y
CONFIG_KEYBOARD_PXA27x=y
CONFIG_KEYBOARD_PXA930_ROTARY=y
CONFIG_MOUSE_PXA930_TRKBALL=y
CONFIG_INPUT_TOUCHSCREEN=y
# CONFIG_LEGACY_PTYS is not set
CONFIG_SERIAL_PXA=y
......@@ -59,7 +55,6 @@ CONFIG_GPIO_MAX732X=y
CONFIG_GPIO_PCA953X=y
CONFIG_GPIO_PCF857X=y
CONFIG_GPIO_MAX7301=y
CONFIG_POWER_SUPPLY=y
CONFIG_POWER_SUPPLY_DEBUG=y
CONFIG_PDA_POWER=y
CONFIG_BATTERY_DA9030=y
......
......@@ -15,57 +15,13 @@ CONFIG_EMBEDDED=y
CONFIG_PROFILING=y
# CONFIG_ARCH_MULTI_V7 is not set
CONFIG_ARCH_PXA=y
CONFIG_ARCH_LUBBOCK=y
CONFIG_MACH_MAINSTONE=y
CONFIG_MACH_ZYLONITE300=y
CONFIG_MACH_ZYLONITE320=y
CONFIG_MACH_LITTLETON=y
CONFIG_MACH_TAVOREVB=y
CONFIG_MACH_SAAR=y
CONFIG_ARCH_PXA_IDP=y
CONFIG_ARCH_VIPER=y
CONFIG_MACH_ARCOM_ZEUS=y
CONFIG_MACH_BALLOON3=y
CONFIG_MACH_CSB726=y
CONFIG_CSB726_CSB701=y
CONFIG_MACH_EXEDA=y
CONFIG_MACH_CM_X300=y
CONFIG_MACH_CAPC7117=y
CONFIG_ARCH_GUMSTIX=y
CONFIG_MACH_XCEP=y
CONFIG_TRIZEPS_PXA=y
CONFIG_MACH_TRIZEPS4WL=y
CONFIG_MACH_LOGICPD_PXA270=y
CONFIG_MACH_PCM027=y
CONFIG_MACH_PCM990_BASEBOARD=y
CONFIG_MACH_COLIBRI=y
CONFIG_MACH_COLIBRI_PXA270_INCOME=y
CONFIG_MACH_COLIBRI300=y
CONFIG_MACH_COLIBRI320=y
CONFIG_MACH_COLIBRI_EVALBOARD=y
CONFIG_MACH_VPAC270=y
CONFIG_MACH_H4700=y
CONFIG_MACH_H5000=y
CONFIG_MACH_HIMALAYA=y
CONFIG_MACH_MAGICIAN=y
CONFIG_MACH_MIOA701=y
CONFIG_PXA_EZX=y
CONFIG_MACH_MP900C=y
CONFIG_ARCH_PXA_PALM=y
CONFIG_PXA_SHARPSL=y
CONFIG_MACH_POODLE=y
CONFIG_MACH_CORGI=y
CONFIG_MACH_SHEPHERD=y
CONFIG_MACH_HUSKY=y
CONFIG_MACH_AKITA=y
CONFIG_MACH_BORZOI=y
CONFIG_MACH_TOSA=y
CONFIG_TOSA_BT=m
CONFIG_TOSA_USE_EXT_KEYCODES=y
CONFIG_MACH_ICONTROL=y
CONFIG_ARCH_PXA_ESERIES=y
CONFIG_MACH_ZIPIT2=y
CONFIG_PXA_SYSTEMS_CPLDS=y
CONFIG_AEABI=y
CONFIG_FORCE_MAX_ZONEORDER=9
CONFIG_CMDLINE="root=/dev/ram0 ro"
CONFIG_KEXEC=y
CONFIG_CPU_FREQ=y
......@@ -148,6 +104,7 @@ CONFIG_PCMCIA_PXA2XX=m
CONFIG_DEVTMPFS=y
CONFIG_DEVTMPFS_MOUNT=y
CONFIG_CONNECTOR=y
CONFIG_MTD=y
CONFIG_MTD_AR7_PARTS=m
CONFIG_MTD_CMDLINE_PARTS=m
CONFIG_MTD_OF_PARTS=m
......@@ -159,16 +116,19 @@ CONFIG_MTD_REDBOOT_PARTS_READONLY=y
CONFIG_MTD_BLOCK=m
CONFIG_NFTL=m
CONFIG_NFTL_RW=y
CONFIG_MTD_CFI=y
CONFIG_MTD_JEDECPROBE=m
CONFIG_MTD_CFI_ADV_OPTIONS=y
CONFIG_MTD_CFI_LE_BYTE_SWAP=y
CONFIG_MTD_CFI_GEOMETRY=y
CONFIG_MTD_OTP=y
CONFIG_MTD_CFI_INTELEXT=y
CONFIG_MTD_CFI_AMDSTD=m
CONFIG_MTD_CFI_STAA=m
CONFIG_MTD_RAM=m
CONFIG_MTD_ROM=m
CONFIG_MTD_COMPLEX_MAPPINGS=y
CONFIG_MTD_PHYSMAP=y
CONFIG_MTD_PXA2XX=m
CONFIG_MTD_M25P80=m
CONFIG_MTD_BLOCK2MTD=y
......@@ -178,7 +138,6 @@ CONFIG_MTD_ONENAND_VERIFY_WRITE=y
CONFIG_MTD_ONENAND_GENERIC=m
CONFIG_MTD_RAW_NAND=m
CONFIG_MTD_NAND_SHARPSL=m
CONFIG_MTD_NAND_MARVELL=m
CONFIG_MTD_NAND_TMIO=m
CONFIG_MTD_NAND_BRCMNAND=m
CONFIG_MTD_NAND_GPIO=m
......@@ -285,14 +244,12 @@ CONFIG_KEYBOARD_ATKBD=m
CONFIG_KEYBOARD_QT1070=m
CONFIG_KEYBOARD_GPIO=m
CONFIG_KEYBOARD_PXA27x=m
CONFIG_KEYBOARD_PXA930_ROTARY=m
CONFIG_KEYBOARD_CROS_EC=m
CONFIG_MOUSE_PS2=m
CONFIG_MOUSE_PS2_ELANTECH=y
CONFIG_MOUSE_SERIAL=m
CONFIG_MOUSE_CYAPA=m
CONFIG_MOUSE_ELAN_I2C=m
CONFIG_MOUSE_PXA930_TRKBALL=m
CONFIG_MOUSE_NAVPOINT_PXA27x=m
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_ADS7846=m
......@@ -303,12 +260,9 @@ CONFIG_TOUCHSCREEN_FUJITSU=m
CONFIG_TOUCHSCREEN_ELO=m
CONFIG_TOUCHSCREEN_MTOUCH=m
CONFIG_TOUCHSCREEN_INEXIO=m
CONFIG_TOUCHSCREEN_HTCPEN=m
CONFIG_TOUCHSCREEN_PENMOUNT=m
CONFIG_TOUCHSCREEN_TOUCHRIGHT=m
CONFIG_TOUCHSCREEN_TOUCHWIN=m
CONFIG_TOUCHSCREEN_UCB1400=m
CONFIG_TOUCHSCREEN_WM97XX=m
CONFIG_TOUCHSCREEN_TOUCHIT213=m
CONFIG_TOUCHSCREEN_PCAP=m
CONFIG_TOUCHSCREEN_ST1232=m
......@@ -319,7 +273,6 @@ CONFIG_INPUT_GPIO_ROTARY_ENCODER=m
CONFIG_INPUT_PCAP=m
CONFIG_INPUT_ADXL34X=m
CONFIG_SERIO=m
CONFIG_SERIO_SA1111=m
CONFIG_LEGACY_PTY_COUNT=8
CONFIG_SERIAL_8250=m
CONFIG_SERIAL_8250_CS=m
......@@ -332,6 +285,7 @@ CONFIG_I2C_CHARDEV=m
CONFIG_I2C_MUX_PCA954x=m
CONFIG_I2C_MUX_PINCTRL=m
CONFIG_I2C_DESIGNWARE_PLATFORM=m
CONFIG_I2C_GPIO=y
CONFIG_I2C_PXA_SLAVE=y
CONFIG_I2C_XILINX=m
CONFIG_I2C_CROS_EC_TUNNEL=m
......@@ -431,8 +385,10 @@ CONFIG_V4L_PLATFORM_DRIVERS=y
CONFIG_V4L_MEM2MEM_DRIVERS=y
CONFIG_VIDEO_PXA27x=m
CONFIG_DRM=m
CONFIG_FB=y
CONFIG_FIRMWARE_EDID=y
CONFIG_FB_TILEBLITTING=y
CONFIG_FB_PXA=y
CONFIG_FB_PXA_OVERLAY=y
CONFIG_FB_PXA_PARAMETERS=y
CONFIG_PXA3XX_GCU=m
......@@ -459,21 +415,10 @@ CONFIG_SND_USB_AUDIO=m
CONFIG_SND_SOC=m
CONFIG_SND_ATMEL_SOC=m
CONFIG_SND_PXA2XX_SOC=m
CONFIG_SND_PXA2XX_SOC_CORGI=m
CONFIG_SND_PXA_SOC_SSP=m
CONFIG_SND_PXA2XX_SOC_SPITZ=m
CONFIG_SND_PXA2XX_SOC_Z2=m
CONFIG_SND_PXA2XX_SOC_POODLE=m
CONFIG_SND_PXA2XX_SOC_TOSA=m
CONFIG_SND_PXA2XX_SOC_E740=m
CONFIG_SND_PXA2XX_SOC_E750=m
CONFIG_SND_PXA2XX_SOC_E800=m
CONFIG_SND_PXA2XX_SOC_EM_X270=m
CONFIG_SND_PXA2XX_SOC_PALM27X=y
CONFIG_SND_SOC_ZYLONITE=m
CONFIG_SND_PXA2XX_SOC_HX4700=m
CONFIG_SND_PXA2XX_SOC_MAGICIAN=m
CONFIG_SND_PXA2XX_SOC_MIOA701=m
CONFIG_SND_SOC_AK4642=m
CONFIG_SND_SOC_WM8731_I2C=m
CONFIG_SND_SOC_WM8978=m
CONFIG_SND_SIMPLE_CARD=m
CONFIG_SOUND_PRIME=m
......
......@@ -37,6 +37,7 @@ CONFIG_ARCH_S3C2440=y
CONFIG_MACH_NEO1973_GTA02=y
CONFIG_MACH_RX1950=y
CONFIG_MACH_SMDK2443=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="root=/dev/hda1 ro init=/bin/bash console=ttySAC0"
CONFIG_FPE_NWFPE=y
CONFIG_FPE_NWFPE_XP=y
......
......@@ -5,15 +5,6 @@ CONFIG_KALLSYMS_ALL=y
CONFIG_ARCH_MULTI_V6=y
# CONFIG_ARCH_MULTI_V7 is not set
CONFIG_ARCH_S3C64XX=y
CONFIG_MACH_SMDK6400=y
CONFIG_MACH_ANW6410=y
CONFIG_MACH_MINI6410=y
CONFIG_MACH_REAL6410=y
CONFIG_MACH_SMDK6410=y
CONFIG_MACH_NCP=y
CONFIG_MACH_HMT=y
CONFIG_MACH_SMARTQ5=y
CONFIG_MACH_SMARTQ7=y
CONFIG_MACH_WLF_CRAGG_6410=y
CONFIG_CMDLINE="console=ttySAC0,115200 root=/dev/ram init=/linuxrc initrd=0x51000000,6M ramdisk_size=6144"
CONFIG_VFP=y
......
......@@ -3,6 +3,7 @@ CONFIG_LOG_BUF_SHIFT=14
CONFIG_BLK_DEV_INITRD=y
CONFIG_ARCH_SA1100=y
CONFIG_SA1100_SHANNON=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="console=ttySA0,9600 console=tty1 root=/dev/mtdblock2 init=/linuxrc"
CONFIG_FPE_NWFPE=y
CONFIG_MODULES=y
......
......@@ -7,6 +7,7 @@ CONFIG_KALLSYMS_ALL=y
CONFIG_KALLSYMS_EXTRA_PASS=y
CONFIG_ARCH_SA1100=y
CONFIG_SA1100_SIMPAD=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="mtdparts=sa1100:512k(boot),1m(kernel),-(root) console=ttySA0 root=1f02 noinitrd mem=64M jffs2_orphaned_inodes=delete rootfstype=jffs2"
CONFIG_FPE_NWFPE=y
CONFIG_MODULES=y
......
......@@ -13,6 +13,7 @@ CONFIG_ARCH_MULTI_V4T=y
# CONFIG_ARCH_MULTI_V7 is not set
CONFIG_ARCH_S3C24XX=y
CONFIG_MACH_TCT_HAMMER=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="mem=64M root=/dev/ram0 init=/linuxrc rw"
CONFIG_FPE_NWFPE=y
CONFIG_MODULES=y
......
......@@ -14,6 +14,7 @@ CONFIG_ARCH_PXA=y
CONFIG_TRIZEPS_PXA=y
CONFIG_MACH_TRIZEPS4=y
CONFIG_AEABI=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="root=fe01 console=ttyS0,38400n8 loglevel=5"
CONFIG_FPE_NWFPE=y
CONFIG_FPE_NWFPE_XP=y
......
......@@ -9,6 +9,7 @@ CONFIG_ARCH_PXA=y
CONFIG_ARCH_VIPER=y
CONFIG_IWMMXT=y
CONFIG_AEABI=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="root=31:02 rootfstype=jffs2 ro console=ttyS0,115200"
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=m
......
......@@ -17,6 +17,7 @@ CONFIG_ARCH_PXA=y
CONFIG_MACH_XCEP=y
CONFIG_IWMMXT=y
CONFIG_AEABI=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="root=mtd4 rootfstype=jffs2 ro console=ttyS0,115200"
CONFIG_FPE_NWFPE=y
CONFIG_KPROBES=y
......
......@@ -5,6 +5,7 @@ CONFIG_LOG_BUF_SHIFT=13
CONFIG_ARCH_PXA=y
CONFIG_MACH_ARCOM_ZEUS=y
CONFIG_AEABI=y
CONFIG_UNUSED_BOARD_FILES=y
CONFIG_CMDLINE="root=31:02 rootfstype=jffs2 ro console=ttyS0,115200"
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=m
......
......@@ -2,6 +2,7 @@
menuconfig ARCH_CNS3XXX
bool "Cavium Networks CNS3XXX family"
depends on ARCH_MULTI_V6
depends on ATAGS && UNUSED_BOARD_FILES
select ARM_GIC
help
Support for Cavium Networks CNS3XXX platform.
......
......@@ -21,12 +21,14 @@ comment "DaVinci Core Type"
config ARCH_DAVINCI_DM355
bool "DaVinci 355 based system"
depends on ATAGS && UNUSED_BOARD_FILES
select DAVINCI_AINTC
select ARCH_DAVINCI_DMx
config ARCH_DAVINCI_DA830
bool "DA830/OMAP-L137/AM17x based system"
depends on !ARCH_DAVINCI_DMx || (AUTO_ZRELADDR && ARM_PATCH_PHYS_VIRT)
depends on ATAGS
select ARCH_DAVINCI_DA8XX
# needed on silicon revs 1.0, 1.1:
select CPU_DCACHE_WRITETHROUGH if !CPU_DCACHE_DISABLE
......@@ -35,6 +37,7 @@ config ARCH_DAVINCI_DA830
config ARCH_DAVINCI_DA850
bool "DA850/OMAP-L138/AM18x based system"
depends on !ARCH_DAVINCI_DMx || (AUTO_ZRELADDR && ARM_PATCH_PHYS_VIRT)
depends on ATAGS
select ARCH_DAVINCI_DA8XX
select DAVINCI_CP_INTC
......@@ -43,6 +46,7 @@ config ARCH_DAVINCI_DA8XX
config ARCH_DAVINCI_DM365
bool "DaVinci 365 based system"
depends on ATAGS && UNUSED_BOARD_FILES
select DAVINCI_AINTC
select ARCH_DAVINCI_DMx
......@@ -83,6 +87,7 @@ config MACH_DAVINCI_DM365_EVM
config MACH_DAVINCI_DA830_EVM
bool "TI DA830/OMAP-L137/AM17x Reference Platform"
default ARCH_DAVINCI_DA830
depends on ATAGS && UNUSED_BOARD_FILES
depends on ARCH_DAVINCI_DA830
select GPIO_PCF857X if I2C
help
......@@ -112,6 +117,7 @@ endchoice
config MACH_DAVINCI_DA850_EVM
bool "TI DA850/OMAP-L138/AM18x Reference Platform"
depends on ATAGS && UNUSED_BOARD_FILES
default ARCH_DAVINCI_DA850
depends on ARCH_DAVINCI_DA850
help
......@@ -153,6 +159,7 @@ endchoice
config MACH_MITYOMAPL138
bool "Critical Link MityDSP-L138/MityARM-1808 SoM"
depends on ARCH_DAVINCI_DA850
depends on ATAGS && UNUSED_BOARD_FILES
help
Say Y here to select the Critical Link MityDSP-L138/MityARM-1808
System on Module. Information on this SoM may be found at
......@@ -161,6 +168,7 @@ config MACH_MITYOMAPL138
config MACH_OMAPL138_HAWKBOARD
bool "TI AM1808 / OMAPL-138 Hawkboard platform"
depends on ARCH_DAVINCI_DA850
depends on ATAGS && UNUSED_BOARD_FILES
help
Say Y here to select the TI AM1808 / OMAPL-138 Hawkboard platform .
......
# SPDX-License-Identifier: GPL-2.0
menuconfig ARCH_DOVE
bool "Marvell Dove" if ARCH_MULTI_V7
depends on ATAGS
select CPU_PJ4
select GPIOLIB
select MVEBU_MBUS
......
# SPDX-License-Identifier: GPL-2.0-only
menuconfig ARCH_EP93XX
bool "EP93xx-based"
depends on ATAGS
depends on ARCH_MULTI_V4T
depends on CPU_LITTLE_ENDIAN
select ARCH_SPARSEMEM_ENABLE
......@@ -26,6 +27,7 @@ comment "EP93xx Platforms"
config MACH_ADSSPHERE
bool "Support ADS Sphere"
depends on UNUSED_BOARD_FILES
help
Say 'Y' here if you want your kernel to support the ADS
Sphere board.
......@@ -98,6 +100,7 @@ config MACH_EDB9315A
config MACH_GESBC9312
bool "Support Glomation GESBC-9312-sx"
depends on UNUSED_BOARD_FILES
help
Say 'Y' here if you want your kernel to support the Glomation
GESBC-9312-sx board.
......@@ -108,6 +111,7 @@ config MACH_MICRO9
config MACH_MICRO9H
bool "Support Contec Micro9-High"
select MACH_MICRO9
depends on UNUSED_BOARD_FILES
help
Say 'Y' here if you want your kernel to support the
Contec Micro9-High board.
......@@ -115,6 +119,7 @@ config MACH_MICRO9H
config MACH_MICRO9M
bool "Support Contec Micro9-Mid"
select MACH_MICRO9
depends on UNUSED_BOARD_FILES
help
Say 'Y' here if you want your kernel to support the
Contec Micro9-Mid board.
......@@ -122,6 +127,7 @@ config MACH_MICRO9M
config MACH_MICRO9L
bool "Support Contec Micro9-Lite"
select MACH_MICRO9
depends on UNUSED_BOARD_FILES
help
Say 'Y' here if you want your kernel to support the
Contec Micro9-Lite board.
......@@ -129,18 +135,21 @@ config MACH_MICRO9L
config MACH_MICRO9S
bool "Support Contec Micro9-Slim"
select MACH_MICRO9
depends on UNUSED_BOARD_FILES
help
Say 'Y' here if you want your kernel to support the
Contec Micro9-Slim board.
config MACH_SIM_ONE
bool "Support Simplemachines Sim.One board"
depends on UNUSED_BOARD_FILES
help
Say 'Y' here if you want your kernel to support the
Simplemachines Sim.One board.
config MACH_SNAPPER_CL15
bool "Support Bluewater Systems Snapper CL15 Module"
depends on UNUSED_BOARD_FILES
help
Say 'Y' here if you want your kernel to support the Bluewater
Systems Snapper CL15 Module.
......
......@@ -5,6 +5,7 @@ menu "Footbridge Implementations"
config ARCH_CATS
bool "CATS"
depends on UNUSED_BOARD_FILES
select CLKEVT_I8253
select CLKSRC_I8253
select FOOTBRIDGE_HOST
......
......@@ -3,6 +3,7 @@ menuconfig ARCH_IOP32X
bool "IOP32x-based platforms"
depends on ARCH_MULTI_V5
depends on CPU_LITTLE_ENDIAN
depends on ATAGS && UNUSED_BOARD_FILES
select CPU_XSCALE
select GPIO_IOP
select GPIOLIB
......
......@@ -18,6 +18,7 @@ if ATAGS
config MACH_ASPENITE
bool "Marvell's PXA168 Aspenite Development Board"
depends on ARCH_MULTI_V5
depends on UNUSED_BOARD_FILES
select CPU_PXA168
help
Say 'Y' here if you want to support the Marvell PXA168-based
......@@ -26,6 +27,7 @@ config MACH_ASPENITE
config MACH_ZYLONITE2
bool "Marvell's PXA168 Zylonite2 Development Board"
depends on ARCH_MULTI_V5
depends on UNUSED_BOARD_FILES
select CPU_PXA168
help
Say 'Y' here if you want to support the Marvell PXA168-based
......@@ -34,6 +36,7 @@ config MACH_ZYLONITE2
config MACH_AVENGERS_LITE
bool "Marvell's PXA168 Avengers Lite Development Board"
depends on ARCH_MULTI_V5
depends on UNUSED_BOARD_FILES
select CPU_PXA168
help
Say 'Y' here if you want to support the Marvell PXA168-based
......@@ -42,6 +45,7 @@ config MACH_AVENGERS_LITE
config MACH_TTC_DKB
bool "Marvell's PXA910 TavorEVB/TTC_DKB Development Board"
depends on ARCH_MULTI_V5
depends on UNUSED_BOARD_FILES
select CPU_PXA910
help
Say 'Y' here if you want to support the Marvell PXA910-based
......@@ -50,6 +54,7 @@ config MACH_TTC_DKB
config MACH_BROWNSTONE
bool "Marvell's Brownstone Development Platform"
depends on ARCH_MULTI_V7
depends on UNUSED_BOARD_FILES
select CPU_MMP2
help
Say 'Y' here if you want to support the Marvell MMP2-based
......@@ -61,6 +66,7 @@ config MACH_BROWNSTONE
config MACH_FLINT
bool "Marvell's Flint Development Platform"
depends on ARCH_MULTI_V7
depends on UNUSED_BOARD_FILES
select CPU_MMP2
help
Say 'Y' here if you want to support the Marvell MMP2-based
......@@ -72,6 +78,7 @@ config MACH_FLINT
config MACH_MARVELL_JASPER
bool "Marvell's Jasper Development Platform"
depends on ARCH_MULTI_V7
depends on UNUSED_BOARD_FILES
select CPU_MMP2
help
Say 'Y' here if you want to support the Marvell MMP2-base
......@@ -83,6 +90,7 @@ config MACH_MARVELL_JASPER
config MACH_TETON_BGA
bool "Marvell's PXA168 Teton BGA Development Board"
depends on ARCH_MULTI_V5
depends on UNUSED_BOARD_FILES
select CPU_PXA168
help
Say 'Y' here if you want to support the Marvell PXA168-based
......@@ -91,6 +99,7 @@ config MACH_TETON_BGA
config MACH_GPLUGD
bool "Marvell's PXA168 GuruPlug Display (gplugD) Board"
depends on ARCH_MULTI_V5
depends on UNUSED_BOARD_FILES
select CPU_PXA168
help
Say 'Y' here if you want to support the Marvell PXA168-based
......
......@@ -3,6 +3,7 @@ menuconfig ARCH_MV78XX0
bool "Marvell MV78xx0"
depends on ARCH_MULTI_V5
depends on CPU_LITTLE_ENDIAN
depends on ATAGS && UNUSED_BOARD_FILES
select CPU_FEROCEON
select GPIOLIB
select MVEBU_MBUS
......
......@@ -3,6 +3,7 @@ menuconfig ARCH_OMAP1
bool "TI OMAP1"
depends on ARCH_MULTI_V4T || ARCH_MULTI_V5
depends on CPU_LITTLE_ENDIAN
depends on ATAGS
select ARCH_HAS_HOLES_MEMORYMODEL
select ARCH_OMAP
select CLKSRC_MMIO
......@@ -131,6 +132,7 @@ comment "OMAP Board Type"
config MACH_OMAP_INNOVATOR
bool "TI Innovator"
depends on ARCH_OMAP15XX || ARCH_OMAP16XX
depends on UNUSED_BOARD_FILES
help
TI OMAP 1510 or 1610 Innovator board support. Say Y here if you
have such a board.
......@@ -138,6 +140,7 @@ config MACH_OMAP_INNOVATOR
config MACH_OMAP_H2
bool "TI H2 Support"
depends on ARCH_OMAP16XX
depends on UNUSED_BOARD_FILES
help
TI OMAP 1610/1611B H2 board support. Say Y here if you have such
a board.
......@@ -145,6 +148,7 @@ config MACH_OMAP_H2
config MACH_OMAP_H3
bool "TI H3 Support"
depends on ARCH_OMAP16XX
depends on UNUSED_BOARD_FILES
help
TI OMAP 1710 H3 board support. Say Y here if you have such
a board.
......@@ -152,6 +156,7 @@ config MACH_OMAP_H3
config MACH_HERALD
bool "HTC Herald"
depends on ARCH_OMAP850
depends on UNUSED_BOARD_FILES
help
HTC Herald smartphone support (AKA T-Mobile Wing, ...)
......@@ -165,6 +170,7 @@ config MACH_OMAP_OSK
config OMAP_OSK_MISTRAL
bool "Mistral QVGA board Support"
depends on MACH_OMAP_OSK
depends on UNUSED_BOARD_FILES
help
The OSK supports an optional add-on board with a Quarter-VGA
touchscreen, PDA-ish buttons, a resume button, bicolor LED,
......@@ -173,6 +179,7 @@ config OMAP_OSK_MISTRAL
config MACH_OMAP_PERSEUS2
bool "TI Perseus2"
depends on ARCH_OMAP730
depends on UNUSED_BOARD_FILES
help
Support for TI OMAP 730 Perseus2 board. Say Y here if you have such
a board.
......@@ -180,6 +187,7 @@ config MACH_OMAP_PERSEUS2
config MACH_OMAP_FSAMPLE
bool "TI F-Sample"
depends on ARCH_OMAP730
depends on UNUSED_BOARD_FILES
help
Support for TI OMAP 850 F-Sample board. Say Y here if you have such
a board.
......@@ -196,6 +204,7 @@ config MACH_OMAP_PALMTE
config MACH_OMAP_PALMZ71
bool "Palm Zire71"
depends on ARCH_OMAP15XX
depends on UNUSED_BOARD_FILES
help
Support for the Palm Zire71 PDA. To boot the kernel,
you'll need a PalmOS compatible bootloader; check out
......@@ -205,6 +214,7 @@ config MACH_OMAP_PALMZ71
config MACH_OMAP_PALMTT
bool "Palm Tungsten|T"
depends on ARCH_OMAP15XX
depends on UNUSED_BOARD_FILES
help
Support for the Palm Tungsten|T PDA. To boot the kernel, you'll
need a PalmOS compatible bootloader (Garux); check out
......@@ -245,6 +255,7 @@ config MACH_AMS_DELTA
config MACH_OMAP_GENERIC
bool "Generic OMAP board"
depends on ARCH_OMAP15XX || ARCH_OMAP16XX
depends on UNUSED_BOARD_FILES
help
Support for generic OMAP-1510, 1610 or 1710 board with
no FPGA. Can be used as template for porting Linux to
......
......@@ -31,6 +31,7 @@ config ARCH_ORION5X_DT
config MACH_DB88F5281
bool "Marvell Orion-2 Development Board"
select I2C_BOARDINFO if I2C
depends on ATAGS && UNUSED_BOARD_FILES
help
Say 'Y' here if you want your kernel to support the
Marvell Orion-2 (88F5281) Development Board
......@@ -38,6 +39,7 @@ config MACH_DB88F5281
config MACH_RD88F5182
bool "Marvell Orion-NAS Reference Design"
select I2C_BOARDINFO if I2C
depends on ATAGS && UNUSED_BOARD_FILES
help
Say 'Y' here if you want your kernel to support the
Marvell Orion-NAS (88F5182) RD2
......@@ -53,6 +55,7 @@ config MACH_RD88F5182_DT
config MACH_KUROBOX_PRO
bool "KuroBox Pro"
select I2C_BOARDINFO if I2C
depends on ATAGS
help
Say 'Y' here if you want your kernel to support the
KuroBox Pro platform.
......@@ -60,24 +63,28 @@ config MACH_KUROBOX_PRO
config MACH_DNS323
bool "D-Link DNS-323"
select I2C_BOARDINFO if I2C
depends on ATAGS
help
Say 'Y' here if you want your kernel to support the
D-Link DNS-323 platform.
config MACH_TS209
bool "QNAP TS-109/TS-209"
depends on ATAGS
help
Say 'Y' here if you want your kernel to support the
QNAP TS-109/TS-209 platform.
config MACH_TERASTATION_PRO2
bool "Buffalo Terastation Pro II/Live"
depends on ATAGS
help
Say 'Y' here if you want your kernel to support the
Buffalo Terastation Pro II/Live platform.
config MACH_LINKSTATION_PRO
bool "Buffalo Linkstation Pro/Live"
depends on ATAGS
select I2C_BOARDINFO if I2C
help
Say 'Y' here if you want your kernel to support the
......@@ -93,6 +100,7 @@ config MACH_LINKSTATION_MINI
config MACH_LINKSTATION_LS_HGL
bool "Buffalo Linkstation LS-HGL"
depends on ATAGS && UNUSED_BOARD_FILES
select I2C_BOARDINFO if I2C
help
Say 'Y' here if you want your kernel to support the
......@@ -100,24 +108,28 @@ config MACH_LINKSTATION_LS_HGL
config MACH_TS409
bool "QNAP TS-409"
depends on ATAGS
help
Say 'Y' here if you want your kernel to support the
QNAP TS-409 platform.
config MACH_WRT350N_V2
bool "Linksys WRT350N v2"
depends on ATAGS && UNUSED_BOARD_FILES
help
Say 'Y' here if you want your kernel to support the
Linksys WRT350N v2 platform.
config MACH_TS78XX
bool "Technologic Systems TS-78xx"
depends on ATAGS
help
Say 'Y' here if you want your kernel to support the
Technologic Systems TS-78xx platform.
config MACH_MV2120
bool "HP Media Vault mv2120"
depends on ATAGS
help
Say 'Y' here if you want your kernel to support the
HP Media Vault mv2120 or mv5100.
......@@ -131,6 +143,7 @@ config MACH_D2NET_DT
config MACH_NET2BIG
bool "LaCie 2Big Network"
depends on ATAGS
select I2C_BOARDINFO if I2C
help
Say 'Y' here if you want your kernel to support the
......@@ -145,24 +158,28 @@ config MACH_MSS2_DT
config MACH_WNR854T
bool "Netgear WNR854T"
depends on ATAGS && UNUSED_BOARD_FILES
help
Say 'Y' here if you want your kernel to support the
Netgear WNR854T platform.
config MACH_RD88F5181L_GE
bool "Marvell Orion-VoIP GE Reference Design"
depends on ATAGS && UNUSED_BOARD_FILES
help
Say 'Y' here if you want your kernel to support the
Marvell Orion-VoIP GE (88F5181L) RD.
config MACH_RD88F5181L_FXO
bool "Marvell Orion-VoIP FXO Reference Design"
depends on ATAGS && UNUSED_BOARD_FILES
help
Say 'Y' here if you want your kernel to support the
Marvell Orion-VoIP FXO (88F5181L) RD.
config MACH_RD88F6183AP_GE
bool "Marvell Orion-1-90 AP GE Reference Design"
depends on ATAGS && UNUSED_BOARD_FILES
help
Say 'Y' here if you want your kernel to support the
Marvell Orion-1-90 (88F6183) AP GE RD.
......
......@@ -54,14 +54,18 @@ config MACH_PXA3XX_DT
the device tree. Needn't select any other machine while
MACH_PXA3XX_DT is enabled.
if ATAGS
config ARCH_LUBBOCK
bool "Intel DBPXA250 Development Platform (aka Lubbock)"
depends on UNUSED_BOARD_FILES
select GPIO_REG
select PXA25x
select SA1111
config MACH_MAINSTONE
bool "Intel HCDDBBVA0 Development Platform (aka Mainstone)"
depends on UNUSED_BOARD_FILES
select GPIO_REG
select PXA27x
......@@ -71,23 +75,27 @@ config MACH_ZYLONITE
config MACH_ZYLONITE300
bool "PXA3xx Development Platform (aka Zylonite) PXA300/310"
depends on UNUSED_BOARD_FILES
select CPU_PXA300
select CPU_PXA310
select MACH_ZYLONITE
config MACH_ZYLONITE320
bool "PXA3xx Development Platform (aka Zylonite) PXA320"
depends on UNUSED_BOARD_FILES
select CPU_PXA320
select MACH_ZYLONITE
config MACH_LITTLETON
bool "PXA3xx Form Factor Platform (aka Littleton)"
depends on UNUSED_BOARD_FILES
select CPU_PXA300
select CPU_PXA310
select PXA3xx
config MACH_TAVOREVB
bool "PXA930 Evaluation Board (aka TavorEVB)"
depends on UNUSED_BOARD_FILES
select CPU_PXA930
select CPU_PXA935
select PXA3xx
......@@ -96,6 +104,7 @@ config MACH_TAVOREVB
config MACH_SAAR
bool "PXA930 Handheld Platform (aka SAAR)"
depends on UNUSED_BOARD_FILES
select CPU_PXA930
select CPU_PXA935
select PXA3xx
......@@ -106,10 +115,12 @@ comment "Third Party Dev Platforms (sorted by vendor name)"
config ARCH_PXA_IDP
bool "Accelent Xscale IDP"
depends on UNUSED_BOARD_FILES
select PXA25x
config ARCH_VIPER
bool "Arcom/Eurotech VIPER SBC"
depends on UNUSED_BOARD_FILES
select ARCOM_PCMCIA
select I2C_GPIO if I2C=y
select ISA
......@@ -117,17 +128,20 @@ config ARCH_VIPER
config MACH_ARCOM_ZEUS
bool "Arcom/Eurotech ZEUS SBC"
depends on UNUSED_BOARD_FILES
select ARCOM_PCMCIA
select ISA
select PXA27x
config MACH_BALLOON3
bool "Balloon 3 board"
depends on UNUSED_BOARD_FILES
select IWMMXT
select PXA27x
config MACH_CSB726
bool "Enable Cogent CSB726 System On a Module"
depends on UNUSED_BOARD_FILES
select IWMMXT
select PXA27x
help
......@@ -136,16 +150,19 @@ config MACH_CSB726
config CSB726_CSB701
bool "Enable support for CSB701 baseboard"
depends on UNUSED_BOARD_FILES
depends on MACH_CSB726
config MACH_CM_X300
bool "CompuLab CM-X300 modules"
depends on UNUSED_BOARD_FILES
select CPU_PXA300
select CPU_PXA310
select PXA3xx
config MACH_CAPC7117
bool "Embedian CAPC-7117 evaluation kit based on the MXM-8x10 CoM"
depends on UNUSED_BOARD_FILES
select CPU_PXA320
select PXA3xx
......@@ -170,6 +187,7 @@ endchoice
config MACH_XCEP
bool "Iskratel Electronics XCEP"
depends on UNUSED_BOARD_FILES
select MTD
select MTD_CFI
select MTD_CFI_INTELEXT
......@@ -181,6 +199,7 @@ config MACH_XCEP
config TRIZEPS_PXA
bool "PXA based Keith und Koep Trizeps DIMM-Modules"
depends on UNUSED_BOARD_FILES
config MACH_TRIZEPS4
bool "Keith und Koep Trizeps4 DIMM-Module"
......@@ -222,15 +241,18 @@ config TRIZEPS_PCMCIA
config MACH_LOGICPD_PXA270
bool "LogicPD PXA270 Card Engine Development Platform"
depends on UNUSED_BOARD_FILES
select PXA27x
config MACH_PCM027
bool "Phytec phyCORE-PXA270 CPU module (PCM-027)"
depends on UNUSED_BOARD_FILES
select IWMMXT
select PXA27x
config MACH_PCM990_BASEBOARD
bool "PHYTEC PCM-990 development board"
depends on UNUSED_BOARD_FILES
depends on MACH_PCM027
choice
......@@ -250,30 +272,36 @@ endchoice
config MACH_COLIBRI
bool "Toradex Colibri PXA270"
depends on UNUSED_BOARD_FILES
select PXA27x
config MACH_COLIBRI_PXA270_INCOME
bool "Income s.r.o. PXA270 SBC"
depends on UNUSED_BOARD_FILES
depends on MACH_COLIBRI
select PXA27x
config MACH_COLIBRI300
bool "Toradex Colibri PXA300/310"
depends on UNUSED_BOARD_FILES
select CPU_PXA300
select CPU_PXA310
select PXA3xx
config MACH_COLIBRI320
bool "Toradex Colibri PXA320"
depends on UNUSED_BOARD_FILES
select CPU_PXA320
select PXA3xx
config MACH_COLIBRI_EVALBOARD
bool "Toradex Colibri Evaluation Carrier Board support"
depends on UNUSED_BOARD_FILES
depends on MACH_COLIBRI || MACH_COLIBRI300 || MACH_COLIBRI320
config MACH_VPAC270
bool "Voipac PXA270"
depends on UNUSED_BOARD_FILES
select HAVE_PATA_PLATFORM
select PXA27x
help
......@@ -283,24 +311,29 @@ comment "End-user Products (sorted by vendor name)"
config MACH_H4700
bool "HP iPAQ hx4700"
depends on UNUSED_BOARD_FILES
select IWMMXT
select PXA27x
config MACH_H5000
bool "HP iPAQ h5000"
depends on UNUSED_BOARD_FILES
select PXA25x
config MACH_HIMALAYA
bool "HTC Himalaya Support"
depends on UNUSED_BOARD_FILES
select CPU_PXA26x
config MACH_MAGICIAN
bool "Enable HTC Magician Support"
depends on UNUSED_BOARD_FILES
select IWMMXT
select PXA27x
config MACH_MIOA701
bool "Mitac Mio A701 Support"
depends on UNUSED_BOARD_FILES
select IWMMXT
select PXA27x
help
......@@ -310,6 +343,7 @@ config MACH_MIOA701
config PXA_EZX
bool "Motorola EZX Platform"
depends on UNUSED_BOARD_FILES
select IWMMXT
select PXA27x
......@@ -345,16 +379,19 @@ config MACH_EZX_E2
config MACH_MP900C
bool "Nec Mobilepro 900/c"
depends on UNUSED_BOARD_FILES
select PXA25x
config ARCH_PXA_PALM
bool "PXA based Palm PDAs"
depends on UNUSED_BOARD_FILES
config MACH_PALM27X
bool
config MACH_PALMTE2
bool "Palm Tungsten|E2"
depends on UNUSED_BOARD_FILES
default y
depends on ARCH_PXA_PALM
select PXA25x
......@@ -373,6 +410,7 @@ config MACH_PALMTC
config MACH_PALMT5
bool "Palm Tungsten|T5"
depends on UNUSED_BOARD_FILES
default y
depends on ARCH_PXA_PALM
select IWMMXT
......@@ -384,6 +422,7 @@ config MACH_PALMT5
config MACH_PALMTX
bool "Palm T|X"
depends on UNUSED_BOARD_FILES
default y
depends on ARCH_PXA_PALM
select IWMMXT
......@@ -395,6 +434,7 @@ config MACH_PALMTX
config MACH_PALMZ72
bool "Palm Zire 72"
depends on UNUSED_BOARD_FILES
default y
depends on ARCH_PXA_PALM
select IWMMXT
......@@ -406,6 +446,7 @@ config MACH_PALMZ72
config MACH_PALMLD
bool "Palm LifeDrive"
depends on UNUSED_BOARD_FILES
default y
depends on ARCH_PXA_PALM
select IWMMXT
......@@ -421,6 +462,7 @@ config PALM_TREO
config MACH_CENTRO
bool "Palm Centro 685 (GSM)"
depends on UNUSED_BOARD_FILES
default y
depends on ARCH_PXA_PALM
select IWMMXT
......@@ -433,6 +475,7 @@ config MACH_CENTRO
config MACH_TREO680
bool "Palm Treo 680"
depends on UNUSED_BOARD_FILES
default y
depends on ARCH_PXA_PALM
select IWMMXT
......@@ -465,24 +508,28 @@ config PXA_SHARPSL_DETECT_MACH_ID
config MACH_POODLE
bool "Enable Sharp SL-5600 (Poodle) Support"
depends on PXA_SHARPSL
depends on UNUSED_BOARD_FILES
select PXA25x
select SHARP_LOCOMO
config MACH_CORGI
bool "Enable Sharp SL-C700 (Corgi) Support"
depends on PXA_SHARPSL
depends on UNUSED_BOARD_FILES
select PXA25x
select PXA_SHARP_C7xx
config MACH_SHEPHERD
bool "Enable Sharp SL-C750 (Shepherd) Support"
depends on PXA_SHARPSL
depends on UNUSED_BOARD_FILES
select PXA25x
select PXA_SHARP_C7xx
config MACH_HUSKY
bool "Enable Sharp SL-C760 (Husky) Support"
depends on PXA_SHARPSL
depends on UNUSED_BOARD_FILES
select PXA25x
select PXA_SHARP_C7xx
......@@ -509,6 +556,7 @@ config MACH_BORZOI
config MACH_TOSA
bool "Enable Sharp SL-6000x (Tosa) Support"
depends on UNUSED_BOARD_FILES
depends on PXA_SHARPSL
select PXA25x
......@@ -532,11 +580,13 @@ config TOSA_USE_EXT_KEYCODES
config MACH_ICONTROL
bool "TMT iControl/SafeTCam based on the MXM-8x10 CoM"
depends on UNUSED_BOARD_FILES
select CPU_PXA320
select PXA3xx
config ARCH_PXA_ESERIES
bool "PXA based Toshiba e-series PDAs"
depends on UNUSED_BOARD_FILES
select FB_W100
select FB
select PXA25x
......@@ -591,7 +641,10 @@ config MACH_E800
config MACH_ZIPIT2
bool "Zipit Z2 Handheld"
depends on UNUSED_BOARD_FILES
select PXA27x
endif # ATAGS
endmenu
config PXA25x
......
......@@ -8,7 +8,7 @@ menuconfig ARCH_S3C24XX
bool "Samsung S3C24XX SoCs (deprecated, see help)"
depends on ARCH_MULTI_V4T || ARCH_MULTI_V5
depends on CPU_LITTLE_ENDIAN
select ATAGS
depends on ATAGS && UNUSED_BOARD_FILES
select CLKSRC_SAMSUNG_PWM
select GPIO_SAMSUNG
select GPIOLIB
......
......@@ -115,7 +115,7 @@ config S3C64XX_SETUP_USB_PHY
config MACH_SMDK6400
bool "SMDK6400"
depends on ATAGS
depends on ATAGS && UNUSED_BOARD_FILES
select CPU_S3C6400
select S3C64XX_SETUP_SDHCI
select S3C_DEV_HSMMC1
......@@ -126,7 +126,7 @@ config MACH_SMDK6400
config MACH_ANW6410
bool "A&W6410"
depends on ATAGS
depends on ATAGS && UNUSED_BOARD_FILES
select CPU_S3C6410
select S3C64XX_SETUP_FB_24BPP
select S3C_DEV_FB
......@@ -135,7 +135,7 @@ config MACH_ANW6410
config MACH_MINI6410
bool "MINI6410"
depends on ATAGS
depends on ATAGS && UNUSED_BOARD_FILES
select CPU_S3C6410
select S3C64XX_SETUP_FB_24BPP
select S3C64XX_SETUP_SDHCI
......@@ -151,7 +151,7 @@ config MACH_MINI6410
config MACH_REAL6410
bool "REAL6410"
depends on ATAGS
depends on ATAGS && UNUSED_BOARD_FILES
select CPU_S3C6410
select S3C64XX_SETUP_FB_24BPP
select S3C64XX_SETUP_SDHCI
......@@ -167,7 +167,7 @@ config MACH_REAL6410
config MACH_SMDK6410
bool "SMDK6410"
depends on ATAGS
depends on ATAGS && UNUSED_BOARD_FILES
select CPU_S3C6410
select S3C64XX_SETUP_FB_24BPP
select S3C64XX_SETUP_I2C1
......@@ -254,7 +254,7 @@ config SMDK6410_WM1192_EV1
config MACH_NCP
bool "NCP"
depends on ATAGS
depends on ATAGS && UNUSED_BOARD_FILES
select CPU_S3C6410
select S3C64XX_SETUP_I2C1
select S3C_DEV_HSMMC1
......@@ -264,7 +264,7 @@ config MACH_NCP
config MACH_HMT
bool "Airgoo HMT"
depends on ATAGS
depends on ATAGS && UNUSED_BOARD_FILES
select CPU_S3C6410
select S3C64XX_SETUP_FB_24BPP
select S3C_DEV_FB
......@@ -296,14 +296,14 @@ config MACH_SMARTQ
config MACH_SMARTQ5
bool "SmartQ 5"
depends on ATAGS
depends on ATAGS && UNUSED_BOARD_FILES
select MACH_SMARTQ
help
Machine support for the SmartQ 5
config MACH_SMARTQ7
bool "SmartQ 7"
depends on ATAGS
depends on ATAGS && UNUSED_BOARD_FILES
select MACH_SMARTQ
help
Machine support for the SmartQ 7
......
......@@ -25,6 +25,7 @@ config ASSABET_NEPONSET
config SA1100_CERF
bool "CerfBoard"
depends on UNUSED_BOARD_FILES
select ARM_SA1110_CPUFREQ
select LEDS_GPIO_REGISTER
help
......@@ -62,6 +63,7 @@ config SA1100_COLLIE
config SA1100_H3100
bool "Compaq iPAQ H3100"
depends on UNUSED_BOARD_FILES
select ARM_SA1110_CPUFREQ
select HTC_EGPIO
select MFD_IPAQ_MICRO
......@@ -80,6 +82,7 @@ config SA1100_H3600
config SA1100_BADGE4
bool "HP Labs BadgePAD 4"
depends on UNUSED_BOARD_FILES
select ARM_SA1100_CPUFREQ
select SA1111
help
......@@ -88,6 +91,7 @@ config SA1100_BADGE4
config SA1100_JORNADA720
bool "HP Jornada 720"
depends on UNUSED_BOARD_FILES
# FIXME: select ARM_SA11x0_CPUFREQ
select SA1111
help
......@@ -107,6 +111,7 @@ config SA1100_JORNADA720_SSP
config SA1100_HACKKIT
bool "HackKit Core CPU Board"
depends on UNUSED_BOARD_FILES
select ARM_SA1100_CPUFREQ
help
Say Y here to support the HackKit Core CPU Board
......@@ -114,6 +119,7 @@ config SA1100_HACKKIT
config SA1100_LART
bool "LART"
depends on UNUSED_BOARD_FILES
select ARM_SA1100_CPUFREQ
help
Say Y here if you are using the Linux Advanced Radio Terminal
......@@ -122,6 +128,7 @@ config SA1100_LART
config SA1100_NANOENGINE
bool "nanoEngine"
depends on UNUSED_BOARD_FILES
select ARM_SA1110_CPUFREQ
select FORCE_PCI
select PCI_NANOENGINE
......@@ -132,6 +139,7 @@ config SA1100_NANOENGINE
config SA1100_PLEB
bool "PLEB"
depends on UNUSED_BOARD_FILES
select ARM_SA1100_CPUFREQ
help
Say Y here if you are using version 1 of the Portable Linux
......@@ -141,6 +149,7 @@ config SA1100_PLEB
config SA1100_SHANNON
bool "Shannon"
depends on UNUSED_BOARD_FILES
select ARM_SA1100_CPUFREQ
select REGULATOR
select REGULATOR_FIXED_VOLTAGE
......@@ -152,6 +161,7 @@ config SA1100_SHANNON
config SA1100_SIMPAD
bool "Simpad"
depends on UNUSED_BOARD_FILES
select ARM_SA1110_CPUFREQ
help
The SIEMENS webpad SIMpad is based on the StrongARM 1110. There
......@@ -163,6 +173,7 @@ config SA1100_SIMPAD
config SA1100_SSP
tristate "Generic PIO SSP"
depends on UNUSED_BOARD_FILES
help
Say Y here to enable support for the generic PIO SSP driver.
This isn't for audio support, but for attached sensors and
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment