dt-bindings: net: stmmac: Convert the binding to a schemas

Switch the STMMAC / Synopsys DesignWare MAC controller binding to a YAML
schema to enable the DT validation.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>

Documentation/devicetree/bindings/net/stmmac.txt

-* STMicroelectronics 10/100/1000/2500/10000 Ethernet (GMAC/XGMAC)
-
-Required properties:
-- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac" or
-	"snps,dwxgmac-<ip_version>", "snps,dwxgmac".
-	For backwards compatibility: "st,spear600-gmac" is also supported.
-- reg: Address and length of the register set for the device
-- interrupts: Should contain the STMMAC interrupts
-- interrupt-names: Should contain a list of interrupt names corresponding to
-	the interrupts in the interrupts property, if available.
-	Valid interrupt names are:
-  - "macirq" (combined signal for various interrupt events)
-  - "eth_wake_irq" (the interrupt to manage the remote wake-up packet detection)
-  - "eth_lpi" (the interrupt that occurs when Rx exits the LPI state)
-- phy-mode: See ethernet.txt file in the same directory.
-- snps,reset-gpio 	gpio number for phy reset.
-- snps,reset-active-low boolean flag to indicate if phy reset is active low.
-- snps,reset-delays-us  is triplet of delays
-	The 1st cell is reset pre-delay in micro seconds.
-	The 2nd cell is reset pulse in micro seconds.
-	The 3rd cell is reset post-delay in micro seconds.
-
-Optional properties:
-- resets: Should contain a phandle to the STMMAC reset signal, if any
-- reset-names: Should contain the reset signal name "stmmaceth", if a
-	reset phandle is given
-- max-frame-size: See ethernet.txt file in the same directory
-- clocks: If present, the first clock should be the GMAC main clock and
-  the second clock should be peripheral's register interface clock. Further
-  clocks may be specified in derived bindings.
-- clock-names: One name for each entry in the clocks property, the
-  first one should be "stmmaceth" and the second one should be "pclk".
-- ptp_ref: this is the PTP reference clock; in case of the PTP is available
-  this clock is used for programming the Timestamp Addend Register. If not
-  passed then the system clock will be used and this is fine on some
-  platforms.
-- tx-fifo-depth: See ethernet.txt file in the same directory
-- rx-fifo-depth: See ethernet.txt file in the same directory
-- snps,pbl		Programmable Burst Length (tx and rx)
-- snps,txpbl		Tx Programmable Burst Length. Only for GMAC and newer.
-			If set, DMA tx will use this value rather than snps,pbl.
-- snps,rxpbl		Rx Programmable Burst Length. Only for GMAC and newer.
-			If set, DMA rx will use this value rather than snps,pbl.
-- snps,no-pbl-x8	Don't multiply the pbl/txpbl/rxpbl values by 8.
-			For core rev < 3.50, don't multiply the values by 4.
-- snps,aal		Address-Aligned Beats
-- snps,fixed-burst	Program the DMA to use the fixed burst mode
-- snps,mixed-burst	Program the DMA to use the mixed burst mode
-- snps,force_thresh_dma_mode	Force DMA to use the threshold mode for
-				both tx and rx
-- snps,force_sf_dma_mode	Force DMA to use the Store and Forward
-				mode for both tx and rx. This flag is
-				ignored if force_thresh_dma_mode is set.
-- snps,en-tx-lpi-clockgating	Enable gating of the MAC TX clock during
-				TX low-power mode
-- snps,multicast-filter-bins:	Number of multicast filter hash bins
-				supported by this device instance
-- snps,perfect-filter-entries:	Number of perfect filter entries supported
-				by this device instance
-- snps,ps-speed: port selection speed that can be passed to the core when
-		 PCS is supported. For example, this is used in case of SGMII
-		 and MAC2MAC connection.
-- snps,tso: this enables the TSO feature otherwise it will be managed by
-		 MAC HW capability register. Only for GMAC4 and newer.
-- AXI BUS Mode parameters: below the list of all the parameters to program the
-			   AXI register inside the DMA module:
-	- snps,lpi_en: enable Low Power Interface
-	- snps,xit_frm: unlock on WoL
-	- snps,wr_osr_lmt: max write outstanding req. limit
-	- snps,rd_osr_lmt: max read outstanding req. limit
-	- snps,kbbe: do not cross 1KiB boundary.
-	- snps,blen: this is a vector of supported burst length.
-	- snps,fb: fixed-burst
-	- snps,mb: mixed-burst
-	- snps,rb: rebuild INCRx Burst
-- mdio: with compatible = "snps,dwmac-mdio", create and register mdio bus.
-- Multiple RX Queues parameters: below the list of all the parameters to
-				 configure the multiple RX queues:
-	- snps,rx-queues-to-use: number of RX queues to be used in the driver
-	- Choose one of these RX scheduling algorithms:
-		- snps,rx-sched-sp: Strict priority
-		- snps,rx-sched-wsp: Weighted Strict priority
-	- For each RX queue
-		- Choose one of these modes:
-			- snps,dcb-algorithm: Queue to be enabled as DCB
-			- snps,avb-algorithm: Queue to be enabled as AVB
-		- snps,map-to-dma-channel: Channel to map
-		- Specifiy specific packet routing:
-			- snps,route-avcp: AV Untagged Control packets
-			- snps,route-ptp: PTP Packets
-			- snps,route-dcbcp: DCB Control Packets
-			- snps,route-up: Untagged Packets
-			- snps,route-multi-broad: Multicast & Broadcast Packets
-		- snps,priority: RX queue priority (Range: 0x0 to 0xF)
-- Multiple TX Queues parameters: below the list of all the parameters to
-				 configure the multiple TX queues:
-	- snps,tx-queues-to-use: number of TX queues to be used in the driver
-	- Choose one of these TX scheduling algorithms:
-		- snps,tx-sched-wrr: Weighted Round Robin
-		- snps,tx-sched-wfq: Weighted Fair Queuing
-		- snps,tx-sched-dwrr: Deficit Weighted Round Robin
-		- snps,tx-sched-sp: Strict priority
-	- For each TX queue
-		- snps,weight: TX queue weight (if using a DCB weight algorithm)
-		- Choose one of these modes:
-			- snps,dcb-algorithm: TX queue will be working in DCB
-			- snps,avb-algorithm: TX queue will be working in AVB
-			  [Attention] Queue 0 is reserved for legacy traffic
-			  and so no AVB is available in this queue.
-		- Configure Credit Base Shaper (if AVB Mode selected):
-			- snps,send_slope: enable Low Power Interface
-			- snps,idle_slope: unlock on WoL
-			- snps,high_credit: max write outstanding req. limit
-			- snps,low_credit: max read outstanding req. limit
-		- snps,priority: TX queue priority (Range: 0x0 to 0xF)
-Examples:
-
-	stmmac_axi_setup: stmmac-axi-config {
-		snps,wr_osr_lmt = <0xf>;
-		snps,rd_osr_lmt = <0xf>;
-		snps,blen = <256 128 64 32 0 0 0>;
-	};
-
-	mtl_rx_setup: rx-queues-config {
-		snps,rx-queues-to-use = <1>;
-		snps,rx-sched-sp;
-		queue0 {
-			snps,dcb-algorithm;
-			snps,map-to-dma-channel = <0x0>;
-			snps,priority = <0x0>;
-		};
-	};
-
-	mtl_tx_setup: tx-queues-config {
-		snps,tx-queues-to-use = <2>;
-		snps,tx-sched-wrr;
-		queue0 {
-			snps,weight = <0x10>;
-			snps,dcb-algorithm;
-			snps,priority = <0x0>;
-		};
-
-		queue1 {
-			snps,avb-algorithm;
-			snps,send_slope = <0x1000>;
-			snps,idle_slope = <0x1000>;
-			snps,high_credit = <0x3E800>;
-			snps,low_credit = <0xFFC18000>;
-			snps,priority = <0x1>;
-		};
-	};
-
-	gmac0: ethernet@e0800000 {
-		compatible = "st,spear600-gmac";
-		reg = <0xe0800000 0x8000>;
-		interrupt-parent = <&vic1>;
-		interrupts = <24 23 22>;
-		interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
-		mac-address = [000000000000]; /* Filled in by U-Boot */
-		max-frame-size = <3800>;
-		phy-mode = "gmii";
-		snps,multicast-filter-bins = <256>;
-		snps,perfect-filter-entries = <128>;
-		rx-fifo-depth = <16384>;
-		tx-fifo-depth = <16384>;
-		clocks = <&clock>;
-		clock-names = "stmmaceth";
-		snps,axi-config = <&stmmac_axi_setup>;
-		mdio0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "snps,dwmac-mdio";
-			phy1: ethernet-phy@0 {
-			};
-		};
-		snps,mtl-rx-config = <&mtl_rx_setup>;
-		snps,mtl-tx-config = <&mtl_tx_setup>;
-	};
+This file has moved to snps,dwmac.yaml.