ARM: ux500: db8500: list most devices in the snowball device tree

This adds all devices that are normally present through the
u8500_init_machine function in the device tree as well, which
will duplicate the devices that are visible.

This will not do much by itself because the device from the
device tree are not matched by any device driver until they
are converted as well. The next step is to move over one
device at a time to actually be used from the device tree
instead of the hardcoded device using auxdata to pass the
correct platform_data.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

arch/arm/boot/dts/db8500.dtsi

@@ -15,7 +15,233 @@ / {
 	soc-u9500 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "simple-bus";
+		compatible = "stericsson,db8500";
 		ranges;
+
+		pmu {
+			compatible = "arm,cortex-a9-pmu";
+			interrupts = <0 7 0x4>;
+		};
+
+		rtc@80154000 {
+			compatible = "stericsson,db8500-rtc";
+			reg = <0x80154000 0x1000>;
+			interrupts = <0 18 0x4>;
+		};
+
+		gpio0: gpio@8012e000 {
+			compatible = "stericsson,db8500-gpio",
+				"stmicroelectronics,nomadik-gpio";
+			reg =  <0x8012e000 0x80>;
+			interrupts = <0 119 0x4>;
+			supports-sleepmode;
+			gpio-controller;
+		};
+
+		gpio1: gpio@8012e080 {
+			compatible = "stericsson,db8500-gpio",
+				"stmicroelectronics,nomadik-gpio";
+			reg =  <0x8012e080 0x80>;
+			interrupts = <0 120 0x4>;
+			supports-sleepmode;
+			gpio-controller;
+		};
+
+		gpio2: gpio@8000e000 {
+			compatible = "stericsson,db8500-gpio",
+				"stmicroelectronics,nomadik-gpio";
+			reg =  <0x8000e000 0x80>;
+			interrupts = <0 121 0x4>;
+			supports-sleepmode;
+			gpio-controller;
+		};
+
+		gpio3: gpio@8000e080 {
+			compatible = "stericsson,db8500-gpio",
+				"stmicroelectronics,nomadik-gpio";
+			reg =  <0x8000e080 0x80>;
+			interrupts = <0 122 0x4>;
+			supports-sleepmode;
+			gpio-controller;
+		};
+
+		gpio4: gpio@8000e100 {
+			compatible = "stericsson,db8500-gpio",
+				"stmicroelectronics,nomadik-gpio";
+			reg =  <0x8000e100 0x80>;
+			interrupts = <0 123 0x4>;
+			supports-sleepmode;
+			gpio-controller;
+		};
+
+		gpio5: gpio@8000e180 {
+			compatible = "stericsson,db8500-gpio",
+				"stmicroelectronics,nomadik-gpio";
+			reg =  <0x8000e180 0x80>;
+			interrupts = <0 124 0x4>;
+			supports-sleepmode;
+			gpio-controller;
+		};
+
+		gpio6: gpio@8011e000 {
+			compatible = "stericsson,db8500-gpio",
+				"stmicroelectronics,nomadik-gpio";
+			reg =  <0x8011e000 0x80>;
+			interrupts = <0 125 0x4>;
+			supports-sleepmode;
+			gpio-controller;
+		};
+
+		gpio7: gpio@8011e080 {
+			compatible = "stericsson,db8500-gpio",
+				"stmicroelectronics,nomadik-gpio";
+			reg =  <0x8011e080 0x80>;
+			interrupts = <0 126 0x4>;
+			supports-sleepmode;
+			gpio-controller;
+		};
+
+		gpio8: gpio@a03fe000 {
+			compatible = "stericsson,db8500-gpio",
+				"stmicroelectronics,nomadik-gpio";
+			reg =  <0xa03fe000 0x80>;
+			interrupts = <0 127 0x4>;
+			supports-sleepmode;
+			gpio-controller;
+		};
+
+		usb@a03e0000 {
+			compatible = "stericsson,db8500-musb",
+				"mentor,musb";
+			reg = <0xa03e0000 0x10000>;
+			interrupts = <0 23 0x4>;
+		};
+
+		dma-controller@801C0000 {
+			compatible = "stericsson,db8500-dma40",
+					"stericsson,dma40";
+			reg = <0x801C0000 0x1000 0x40010000 0x800>;
+			interrupts = <0 25 0x4>;
+		};
+
+		prcmu@80157000 {
+			compatible = "stericsson,db8500-prcmu";
+			reg = <0x80157000 0x1000>;
+			interrupts = <46 47>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ab8500@5 {
+				compatible = "stericsson,ab8500";
+				reg = <5>; /* mailbox 5 is i2c */
+				interrupts = <0 40 0x4>;
+			};
+		};
+
+		i2c@80004000 {
+			compatible = "stericsson,db8500-i2c", "stmicroelectronics,nomadik-i2c";
+			reg = <0x80004000 0x1000>;
+			interrupts = <0 21 0x4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@80122000 {
+			compatible = "stericsson,db8500-i2c", "stmicroelectronics,nomadik-i2c";
+			reg = <0x80122000 0x1000>;
+			interrupts = <0 22 0x4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@80128000 {
+			compatible = "stericsson,db8500-i2c", "stmicroelectronics,nomadik-i2c";
+			reg = <0x80128000 0x1000>;
+			interrupts = <0 55 0x4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@80110000 {
+			compatible = "stericsson,db8500-i2c", "stmicroelectronics,nomadik-i2c";
+			reg = <0x80110000 0x1000>;
+			interrupts = <0 12 0x4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@8012a000 {
+			compatible = "stericsson,db8500-i2c", "stmicroelectronics,nomadik-i2c";
+			reg = <0x8012a000 0x1000>;
+			interrupts = <0 51 0x4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		ssp@80002000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <80002000 0x1000>;
+			interrupts = <0 14 0x4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+			cs-gpios = <&gpio0 31 &gpio4 14 &gpio4 16 &gpio6 22 &gpio7 0>;
+		};
+
+		uart@80120000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x80120000 0x1000>;
+			interrupts = <0 11 0x4>;
+			status = "disabled";
+		};
+		uart@80121000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x80121000 0x1000>;
+			interrupts = <0 19 0x4>;
+			status = "disabled";
+		};
+		uart@80007000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x80007000 0x1000>;
+			interrupts = <0 26 0x4>;
+			status = "disabled";
+		};
+
+		sdi@80126000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			reg = <0x80126000 0x1000>;
+			interrupts = <0 60 0x4>;
+			status = "disabled";
+		};
+		sdi@80118000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			reg = <0x80118000 0x1000>;
+			interrupts = <0 50 0x4>;
+			status = "disabled";
+		};
+		sdi@80005000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			reg = <0x80005000 0x1000>;
+			interrupts = <0 41 0x4>;
+			status = "disabled";
+		};
+		sdi@80119000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			reg = <0x80119000 0x1000>;
+			interrupts = <0 59 0x4>;
+			status = "disabled";
+		};
+		sdi@80114000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			reg = <0x80114000 0x1000>;
+			interrupts = <0 99 0x4>;
+			status = "disabled";
+		};
+		sdi@80008000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			reg = <0x80114000 0x1000>;
+			interrupts = <0 100 0x4>;
+			status = "disabled";
+		};
 	};
 };

arch/arm/boot/dts/snowball.dts

@@ -20,6 +20,108 @@ memory {
 		reg = <0x00000000 0x20000000>;
 	};
 
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		button@1 {
+			debounce_interval = <50>;
+			wakeup = <1>;
+			linux,code = <2>;
+			label = "userpb";
+			gpios = <&gpio1 0>;
+		};
+		button@2 {
+			debounce_interval = <50>;
+			wakeup = <1>;
+			linux,code = <3>;
+			label = "userpb";
+			gpios = <&gpio4 23>;
+		};
+		button@3 {
+			debounce_interval = <50>;
+			wakeup = <1>;
+			linux,code = <4>;
+			label = "userpb";
+			gpios = <&gpio4 23>;
+		};
+		button@4 {
+			debounce_interval = <50>;
+			wakeup = <1>;
+			linux,code = <5>;
+			label = "userpb";
+			gpios = <&gpio5 1>;
+		};
+		button@5 {
+			debounce_interval = <50>;
+			wakeup = <1>;
+			linux,code = <6>;
+			label = "userpb";
+			gpios = <&gpio5 2>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		used-led {
+			label = "user_led";
+			gpios = <&gpio4 14>;
+		};
+	};
+
 	soc-u9500 {
+
+		external-bus@50000000 {
+			compatible = "simple-bus";
+			reg = <0x50000000 0x10000000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			ethernet@50000000 {
+				compatible = "smsc,9111";
+				reg = <0x50000000 0x10000>;
+				interrupts = <12>;
+				interrupt-parent = <&gpio4>;
+			};
+		};
+
+		sdi@80126000 {
+			status = "enabled";
+			cd-gpios = <&gpio6 26>;
+		};
+
+		sdi@80114000 {
+			status = "enabled";
+		};
+
+		i2c@80004000 {
+			tc3589x@42 {
+				//compatible = "tc3589x";
+				reg = <0x42>;
+				interrupts = <25>;
+				interrupt-parent = <&gpio6>;
+			};
+			tps61052@33 {
+				//compatible = "tps61052";
+				reg = <0x33>;
+			};
+		};
+
+		i2c@80128000 {
+			lp5521@0x33 {
+				// compatible = "lp5521";
+				reg = <0x33>;
+			};
+			lp5521@0x34 {
+				// compatible = "lp5521";
+				reg = <0x34>;
+			};
+			bh1780@0x29 {
+				// compatible = "rohm,bh1780gli";
+				reg = <0x33>;
+			};
+		};
 	};
 };

arch/arm/mach-ux500/board-mop500.c

@@ -621,6 +621,7 @@ static void __init mop500_init_machine(void)
 
 	mop500_pins_init();
 
+	/* FIXME: parent of ab8500 should be prcmu */
 	for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++)
 		mop500_platform_devs[i]->dev.parent = parent;
 
@@ -743,6 +744,17 @@ MACHINE_START(SNOWBALL, "Calao Systems Snowball platform")
 MACHINE_END
 
 #ifdef CONFIG_MACH_UX500_DT
+
+struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = {
+	{},
+};
+
+static const struct of_device_id u8500_soc_node[] = {
+	/* only create devices below soc node */
+	{ .compatible = "stericsson,db8500", },
+	{ },
+};
+
 static void __init u8500_init_machine(void)
 {
 	struct device *parent = NULL;
@@ -757,6 +769,8 @@ static void __init u8500_init_machine(void)
 	for (i = 0; i < ARRAY_SIZE(snowball_platform_devs); i++)
 		snowball_platform_devs[i]->dev.parent = parent;
 
+	/* automatically probe child nodes of db8500 device */
+	of_platform_populate(NULL, u8500_soc_node, u8500_auxdata_lookup, parent);
 
 	if (of_machine_is_compatible("st-ericsson,mop500")) {
 		mop500_gpio_keys[0].gpio = GPIO_PROX_SENSOR;