Merge tag 'exynos-drm-next-for-v4.14' of...

Merge tag 'exynos-drm-next-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next

Summary:
- Provide NV12MT pixel format support of Mixer driver in generic way.
- Refactor Exynos KMS drivers
  . Refactoring to panel detection way
  . Refactoring to setting up possible_crtcs
  . Refactoring to video and command mode support
- Some cleanups

* tag 'exynos-drm-next-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
  drm/exynos: simplify set_pixfmt() in DECON and FIMD drivers
  drm/exynos: consistent use of cpp
  drm/exynos: mixer: remove src offset from mixer_graph_buffer()
  drm/exynos: mixer: simplify mixer_graph_buffer()
  drm/exynos: mixer: simplify vp_video_buffer()
  drm/exynos: mixer: enable NV12MT support for the video plane
  drm/exynos: mixer: fix chroma comment in vp_video_buffer()
  arm64: dts: exynos: remove i80-if-timings nodes
  dt-bindings: exynos5433-decon: remove i80-if-timings property
  drm/exynos/decon5433: use mode info stored in CRTC to detect i80 mode
  drm/exynos: add mode_valid callback to exynos_drm
  drm/exynos/decon5433: refactor irq requesting code
  drm/exynos/mic: use mode info stored in CRTC to detect i80 mode
  drm/exynos/dsi: propagate info about command mode from panel
  drm/exynos/dsi: refactor panel detection logic
  drm/exynos: use helper to set possible crtcs
  drm/exynos/decon5433: use readl_poll_timeout helpers

Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt

@@ -25,12 +25,6 @@ Required properties:
 	 size-cells must 1 and 0, respectively.
 - port: contains an endpoint node which is connected to the endpoint in the mic
 	node. The reg value muset be 0.
-- i80-if-timings: specify whether the panel which is connected to decon uses
-		  i80 lcd interface or mipi video interface. This node contains
-		  no timing information as that of fimd does. Because there is
-		  no register in decon to specify i80 interface timing value,
-		  it is not needed, but make it remain to use same kind of node
-		  in fimd and exynos7 decon.
 
 Example:
 SoC specific DT entry:
@@ -59,9 +53,3 @@ decon: decon@13800000 {
 		};
 	};
 };
-
-Board specific DT entry:
-&decon {
-	i80-if-timings {
-	};
-};

arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi

@@ -280,9 +280,6 @@ &cpu4 {
 
 &decon {
 	status = "okay";
-
-	i80-if-timings {
-	};
 };
 
 &decon_tv {
@@ -1116,9 +1113,6 @@ &pwm {
 
 &mic {
 	status = "okay";
-
-	i80-if-timings {
-	};
 };
 
 &pmu_system_controller {

drivers/gpu/drm/exynos/exynos5433_drm_decon.c

@@ -13,6 +13,7 @@
 #include <linux/platform_device.h>
 #include <linux/clk.h>
 #include <linux/component.h>
+#include <linux/iopoll.h>
 #include <linux/mfd/syscon.h>
 #include <linux/of_device.h>
 #include <linux/of_gpio.h>
@@ -33,9 +34,8 @@
 #define WINDOWS_NR	3
 #define MIN_FB_WIDTH_FOR_16WORD_BURST	128
 
-#define IFTYPE_I80	(1 << 0)
-#define I80_HW_TRG	(1 << 1)
-#define IFTYPE_HDMI	(1 << 2)
+#define I80_HW_TRG	(1 << 0)
+#define IFTYPE_HDMI	(1 << 1)
 
 static const char * const decon_clks_name[] = {
 	"pclk",
@@ -57,6 +57,8 @@ struct decon_context {
 	struct regmap			*sysreg;
 	struct clk			*clks[ARRAY_SIZE(decon_clks_name)];
 	unsigned int			irq;
+	unsigned int			irq_vsync;
+	unsigned int			irq_lcd_sys;
 	unsigned int			te_irq;
 	unsigned long			out_type;
 	int				first_win;
@@ -90,7 +92,7 @@ static int decon_enable_vblank(struct exynos_drm_crtc *crtc)
 	u32 val;
 
 	val = VIDINTCON0_INTEN;
-	if (ctx->out_type & IFTYPE_I80)
+	if (crtc->i80_mode)
 		val |= VIDINTCON0_FRAMEDONE;
 	else
 		val |= VIDINTCON0_INTFRMEN | VIDINTCON0_FRAMESEL_FP;
@@ -139,7 +141,7 @@ static u32 decon_get_frame_count(struct decon_context *ctx, bool end)
 
 	switch (status & (VIDCON1_VSTATUS_MASK | VIDCON1_I80_ACTIVE)) {
 	case VIDCON1_VSTATUS_VS:
-		if (!(ctx->out_type & IFTYPE_I80))
+		if (!(ctx->crtc->i80_mode))
 			--frm;
 		break;
 	case VIDCON1_VSTATUS_BP:
@@ -166,7 +168,7 @@ static u32 decon_get_vblank_counter(struct exynos_drm_crtc *crtc)
 
 static void decon_setup_trigger(struct decon_context *ctx)
 {
-	if (!(ctx->out_type & (IFTYPE_I80 | I80_HW_TRG)))
+	if (!ctx->crtc->i80_mode && !(ctx->out_type & I80_HW_TRG))
 		return;
 
 	if (!(ctx->out_type & I80_HW_TRG)) {
@@ -206,7 +208,7 @@ static void decon_commit(struct exynos_drm_crtc *crtc)
 	val = VIDOUT_LCD_ON;
 	if (interlaced)
 		val |= VIDOUT_INTERLACE_EN_F;
-	if (ctx->out_type & IFTYPE_I80) {
+	if (crtc->i80_mode) {
 		val |= VIDOUT_COMMAND_IF;
 	} else {
 		val |= VIDOUT_RGB_IF;
@@ -222,7 +224,7 @@ static void decon_commit(struct exynos_drm_crtc *crtc)
 			VIDTCON2_HOZVAL(m->hdisplay - 1);
 	writel(val, ctx->addr + DECON_VIDTCON2);
 
-	if (!(ctx->out_type & IFTYPE_I80)) {
+	if (!crtc->i80_mode) {
 		int vbp = m->crtc_vtotal - m->crtc_vsync_end;
 		int vfp = m->crtc_vsync_start - m->crtc_vdisplay;
 
@@ -277,16 +279,14 @@ static void decon_win_set_pixfmt(struct decon_context *ctx, unsigned int win,
 		val |= WINCONx_BURSTLEN_16WORD;
 		break;
 	case DRM_FORMAT_ARGB8888:
+	default:
 		val |= WINCONx_BPPMODE_32BPP_A8888;
 		val |= WINCONx_WSWP_F | WINCONx_BLD_PIX_F | WINCONx_ALPHA_SEL_F;
 		val |= WINCONx_BURSTLEN_16WORD;
 		break;
-	default:
-		DRM_ERROR("Proper pixel format is not set\n");
-		return;
 	}
 
-	DRM_DEBUG_KMS("bpp = %u\n", fb->format->cpp[0] * 8);
+	DRM_DEBUG_KMS("cpp = %u\n", fb->format->cpp[0]);
 
 	/*
 	 * In case of exynos, setting dma-burst to 16Word causes permanent
@@ -329,7 +329,7 @@ static void decon_update_plane(struct exynos_drm_crtc *crtc,
 	struct decon_context *ctx = crtc->ctx;
 	struct drm_framebuffer *fb = state->base.fb;
 	unsigned int win = plane->index;
-	unsigned int bpp = fb->format->cpp[0];
+	unsigned int cpp = fb->format->cpp[0];
 	unsigned int pitch = fb->pitches[0];
 	dma_addr_t dma_addr = exynos_drm_fb_dma_addr(fb, 0);
 	u32 val;
@@ -365,11 +365,11 @@ static void decon_update_plane(struct exynos_drm_crtc *crtc,
 	writel(val, ctx->addr + DECON_VIDW0xADD1B0(win));
 
 	if (!(ctx->out_type & IFTYPE_HDMI))
-		val = BIT_VAL(pitch - state->crtc.w * bpp, 27, 14)
-			| BIT_VAL(state->crtc.w * bpp, 13, 0);
+		val = BIT_VAL(pitch - state->crtc.w * cpp, 27, 14)
+			| BIT_VAL(state->crtc.w * cpp, 13, 0);
 	else
-		val = BIT_VAL(pitch - state->crtc.w * bpp, 29, 15)
-			| BIT_VAL(state->crtc.w * bpp, 14, 0);
+		val = BIT_VAL(pitch - state->crtc.w * cpp, 29, 15)
+			| BIT_VAL(state->crtc.w * cpp, 14, 0);
 	writel(val, ctx->addr + DECON_VIDW0xADD2(win));
 
 	decon_win_set_pixfmt(ctx, win, fb);
@@ -407,24 +407,19 @@ static void decon_atomic_flush(struct exynos_drm_crtc *crtc)
 
 static void decon_swreset(struct decon_context *ctx)
 {
-	unsigned int tries;
 	unsigned long flags;
+	u32 val;
+	int ret;
 
 	writel(0, ctx->addr + DECON_VIDCON0);
-	for (tries = 2000; tries; --tries) {
-		if (~readl(ctx->addr + DECON_VIDCON0) & VIDCON0_STOP_STATUS)
-			break;
-		udelay(10);
-	}
+	readl_poll_timeout(ctx->addr + DECON_VIDCON0, val,
+			   ~val & VIDCON0_STOP_STATUS, 12, 20000);
 
 	writel(VIDCON0_SWRESET, ctx->addr + DECON_VIDCON0);
-	for (tries = 2000; tries; --tries) {
-		if (~readl(ctx->addr + DECON_VIDCON0) & VIDCON0_SWRESET)
-			break;
-		udelay(10);
-	}
+	ret = readl_poll_timeout(ctx->addr + DECON_VIDCON0, val,
+				 ~val & VIDCON0_SWRESET, 12, 20000);
 
-	WARN(tries == 0, "failed to software reset DECON\n");
+	WARN(ret < 0, "failed to software reset DECON\n");
 
 	spin_lock_irqsave(&ctx->vblank_lock, flags);
 	ctx->frame_id = 0;
@@ -515,6 +510,22 @@ static void decon_clear_channels(struct exynos_drm_crtc *crtc)
 		clk_disable_unprepare(ctx->clks[i]);
 }
 
+static enum drm_mode_status decon_mode_valid(struct exynos_drm_crtc *crtc,
+		const struct drm_display_mode *mode)
+{
+	struct decon_context *ctx = crtc->ctx;
+
+	ctx->irq = crtc->i80_mode ? ctx->irq_lcd_sys : ctx->irq_vsync;
+
+	if (ctx->irq)
+		return MODE_OK;
+
+	dev_info(ctx->dev, "Sink requires %s mode, but appropriate interrupt is not provided.\n",
+			crtc->i80_mode ? "command" : "video");
+
+	return MODE_BAD;
+}
+
 static const struct exynos_drm_crtc_ops decon_crtc_ops = {
 	.enable			= decon_enable,
 	.disable		= decon_disable,
@@ -524,6 +535,7 @@ static const struct exynos_drm_crtc_ops decon_crtc_ops = {
 	.atomic_begin		= decon_atomic_begin,
 	.update_plane		= decon_update_plane,
 	.disable_plane		= decon_disable_plane,
+	.mode_valid		= decon_mode_valid,
 	.atomic_flush		= decon_atomic_flush,
 };
 
@@ -674,19 +686,22 @@ static const struct of_device_id exynos5433_decon_driver_dt_match[] = {
 MODULE_DEVICE_TABLE(of, exynos5433_decon_driver_dt_match);
 
 static int decon_conf_irq(struct decon_context *ctx, const char *name,
-		irq_handler_t handler, unsigned long int flags, bool required)
+		irq_handler_t handler, unsigned long int flags)
 {
 	struct platform_device *pdev = to_platform_device(ctx->dev);
 	int ret, irq = platform_get_irq_byname(pdev, name);
 
 	if (irq < 0) {
-		if (irq == -EPROBE_DEFER)
+		switch (irq) {
+		case -EPROBE_DEFER:
 			return irq;
-		if (required)
-			dev_err(ctx->dev, "cannot get %s IRQ\n", name);
-		else
-			irq = 0;
-		return irq;
+		case -ENODATA:
+		case -ENXIO:
+			return 0;
+		default:
+			dev_err(ctx->dev, "IRQ %s get failed, %d\n", name, irq);
+			return irq;
+		}
 	}
 	irq_set_status_flags(irq, IRQ_NOAUTOEN);
 	ret = devm_request_irq(ctx->dev, irq, handler, flags, "drm_decon", ctx);
@@ -714,11 +729,8 @@ static int exynos5433_decon_probe(struct platform_device *pdev)
 	ctx->out_type = (unsigned long)of_device_get_match_data(dev);
 	spin_lock_init(&ctx->vblank_lock);
 
-	if (ctx->out_type & IFTYPE_HDMI) {
+	if (ctx->out_type & IFTYPE_HDMI)
 		ctx->first_win = 1;
-	} else if (of_get_child_by_name(dev->of_node, "i80-if-timings")) {
-		ctx->out_type |= IFTYPE_I80;
-	}
 
 	for (i = 0; i < ARRAY_SIZE(decon_clks_name); i++) {
 		struct clk *clk;
@@ -742,25 +754,23 @@ static int exynos5433_decon_probe(struct platform_device *pdev)
 		return PTR_ERR(ctx->addr);
 	}
 
-	if (ctx->out_type & IFTYPE_I80) {
-		ret = decon_conf_irq(ctx, "lcd_sys", decon_irq_handler, 0, true);
-		if (ret < 0)
-			return ret;
-		ctx->irq = ret;
+	ret = decon_conf_irq(ctx, "vsync", decon_irq_handler, 0);
+	if (ret < 0)
+		return ret;
+	ctx->irq_vsync = ret;
 
-		ret = decon_conf_irq(ctx, "te", decon_te_irq_handler,
-				     IRQF_TRIGGER_RISING, false);
-		if (ret < 0)
-			return ret;
-		if (ret) {
-			ctx->te_irq = ret;
-			ctx->out_type &= ~I80_HW_TRG;
-		}
-	} else {
-		ret = decon_conf_irq(ctx, "vsync", decon_irq_handler, 0, true);
-		if (ret < 0)
+	ret = decon_conf_irq(ctx, "lcd_sys", decon_irq_handler, 0);
+	if (ret < 0)
+		return ret;
+	ctx->irq_lcd_sys = ret;
+
+	ret = decon_conf_irq(ctx, "te", decon_te_irq_handler,
+			IRQF_TRIGGER_RISING);
+	if (ret < 0)
 			return ret;
-		ctx->irq = ret;
+	if (ret) {
+		ctx->te_irq = ret;
+		ctx->out_type &= ~I80_HW_TRG;
 	}
 
 	if (ctx->out_type & I80_HW_TRG) {

drivers/gpu/drm/exynos/exynos7_drm_decon.c

@@ -309,19 +309,14 @@ static void decon_win_set_pixfmt(struct decon_context *ctx, unsigned int win,
 		val |= WINCONx_BURSTLEN_16WORD;
 		break;
 	case DRM_FORMAT_BGRA8888:
+	default:
 		val |= WINCONx_BPPMODE_32BPP_BGRA | WINCONx_BLD_PIX |
 			WINCONx_ALPHA_SEL;
 		val |= WINCONx_BURSTLEN_16WORD;
 		break;
-	default:
-		DRM_DEBUG_KMS("invalid pixel size so using unpacked 24bpp.\n");
-
-		val |= WINCONx_BPPMODE_24BPP_xRGB;
-		val |= WINCONx_BURSTLEN_16WORD;
-		break;
 	}
 
-	DRM_DEBUG_KMS("bpp = %d\n", fb->format->cpp[0] * 8);
+	DRM_DEBUG_KMS("cpp = %d\n", fb->format->cpp[0]);
 
 	/*
 	 * In case of exynos, setting dma-burst to 16Word causes permanent
@@ -398,7 +393,7 @@ static void decon_update_plane(struct exynos_drm_crtc *crtc,
 	unsigned int last_x;
 	unsigned int last_y;
 	unsigned int win = plane->index;
-	unsigned int bpp = fb->format->cpp[0];
+	unsigned int cpp = fb->format->cpp[0];
 	unsigned int pitch = fb->pitches[0];
 
 	if (ctx->suspended)
@@ -418,7 +413,7 @@ static void decon_update_plane(struct exynos_drm_crtc *crtc,
 	val = (unsigned long)exynos_drm_fb_dma_addr(fb, 0);
 	writel(val, ctx->regs + VIDW_BUF_START(win));
 
-	padding = (pitch / bpp) - fb->width;
+	padding = (pitch / cpp) - fb->width;
 
 	/* buffer size */
 	writel(fb->width + padding, ctx->regs + VIDW_WHOLE_X(win));

drivers/gpu/drm/exynos/exynos_dp.c

@@ -155,7 +155,7 @@ static int exynos_dp_bind(struct device *dev, struct device *master, void *data)
 	struct exynos_dp_device *dp = dev_get_drvdata(dev);
 	struct drm_encoder *encoder = &dp->encoder;
 	struct drm_device *drm_dev = data;
-	int pipe, ret;
+	int ret;
 
 	/*
 	 * Just like the probe function said, we don't need the
@@ -179,20 +179,15 @@ static int exynos_dp_bind(struct device *dev, struct device *master, void *data)
 			return ret;
 	}
 
-	pipe = exynos_drm_crtc_get_pipe_from_type(drm_dev,
-						  EXYNOS_DISPLAY_TYPE_LCD);
-	if (pipe < 0)
-		return pipe;
-
-	encoder->possible_crtcs = 1 << pipe;
-
-	DRM_DEBUG_KMS("possible_crtcs = 0x%x\n", encoder->possible_crtcs);
-
 	drm_encoder_init(drm_dev, encoder, &exynos_dp_encoder_funcs,
 			 DRM_MODE_ENCODER_TMDS, NULL);
 
 	drm_encoder_helper_add(encoder, &exynos_dp_encoder_helper_funcs);
 
+	ret = exynos_drm_set_possible_crtcs(encoder, EXYNOS_DISPLAY_TYPE_LCD);
+	if (ret < 0)
+		return ret;
+
 	dp->plat_data.encoder = encoder;
 
 	return analogix_dp_bind(dev, dp->drm_dev, &dp->plat_data);

drivers/gpu/drm/exynos/exynos_drm_core.c

@@ -13,6 +13,7 @@
  */
 
 #include <drm/drmP.h>
+
 #include "exynos_drm_drv.h"
 #include "exynos_drm_crtc.h"
 

drivers/gpu/drm/exynos/exynos_drm_crtc.c

@@ -16,6 +16,7 @@
 #include <drm/drm_crtc_helper.h>
 #include <drm/drm_atomic.h>
 #include <drm/drm_atomic_helper.h>
+#include <drm/drm_encoder.h>
 
 #include "exynos_drm_crtc.h"
 #include "exynos_drm_drv.h"
@@ -83,7 +84,19 @@ static void exynos_crtc_atomic_flush(struct drm_crtc *crtc,
 		exynos_crtc->ops->atomic_flush(exynos_crtc);
 }
 
+static enum drm_mode_status exynos_crtc_mode_valid(struct drm_crtc *crtc,
+	const struct drm_display_mode *mode)
+{
+	struct exynos_drm_crtc *exynos_crtc = to_exynos_crtc(crtc);
+
+	if (exynos_crtc->ops->mode_valid)
+		return exynos_crtc->ops->mode_valid(exynos_crtc, mode);
+
+	return MODE_OK;
+}
+
 static const struct drm_crtc_helper_funcs exynos_crtc_helper_funcs = {
+	.mode_valid	= exynos_crtc_mode_valid,
 	.atomic_check	= exynos_crtc_atomic_check,
 	.atomic_begin	= exynos_crtc_atomic_begin,
 	.atomic_flush	= exynos_crtc_atomic_flush,
@@ -191,16 +204,30 @@ struct exynos_drm_crtc *exynos_drm_crtc_create(struct drm_device *drm_dev,
 	return ERR_PTR(ret);
 }
 
-int exynos_drm_crtc_get_pipe_from_type(struct drm_device *drm_dev,
+struct exynos_drm_crtc *exynos_drm_crtc_get_by_type(struct drm_device *drm_dev,
 				       enum exynos_drm_output_type out_type)
 {
 	struct drm_crtc *crtc;
 
 	drm_for_each_crtc(crtc, drm_dev)
 		if (to_exynos_crtc(crtc)->type == out_type)
-			return drm_crtc_index(crtc);
+			return to_exynos_crtc(crtc);
 
-	return -EPERM;
+	return ERR_PTR(-EPERM);
+}
+
+int exynos_drm_set_possible_crtcs(struct drm_encoder *encoder,
+		enum exynos_drm_output_type out_type)
+{
+	struct exynos_drm_crtc *crtc = exynos_drm_crtc_get_by_type(encoder->dev,
+						out_type);
+
+	if (IS_ERR(crtc))
+		return PTR_ERR(crtc);
+
+	encoder->possible_crtcs = drm_crtc_mask(&crtc->base);
+
+	return 0;
 }
 
 void exynos_drm_crtc_te_handler(struct drm_crtc *crtc)

drivers/gpu/drm/exynos/exynos_drm_crtc.h

@@ -15,21 +15,25 @@
 #ifndef _EXYNOS_DRM_CRTC_H_
 #define _EXYNOS_DRM_CRTC_H_
 
+
 #include "exynos_drm_drv.h"
 
 struct exynos_drm_crtc *exynos_drm_crtc_create(struct drm_device *drm_dev,
 					struct drm_plane *plane,
-					enum exynos_drm_output_type type,
+					enum exynos_drm_output_type out_type,
 					const struct exynos_drm_crtc_ops *ops,
 					void *context);
 void exynos_drm_crtc_wait_pending_update(struct exynos_drm_crtc *exynos_crtc);
 void exynos_drm_crtc_finish_update(struct exynos_drm_crtc *exynos_crtc,
 				   struct exynos_drm_plane *exynos_plane);
 
-/* This function gets pipe value to crtc device matched with out_type. */
-int exynos_drm_crtc_get_pipe_from_type(struct drm_device *drm_dev,
+/* This function gets crtc device matched with out_type. */
+struct exynos_drm_crtc *exynos_drm_crtc_get_by_type(struct drm_device *drm_dev,
 				       enum exynos_drm_output_type out_type);
 
+int exynos_drm_set_possible_crtcs(struct drm_encoder *encoder,
+		enum exynos_drm_output_type out_type);
+
 /*
  * This function calls the crtc device(manager)'s te_handler() callback
  * to trigger to transfer video image at the tearing effect synchronization

drivers/gpu/drm/exynos/exynos_drm_dpi.c

@@ -202,19 +202,15 @@ int exynos_dpi_bind(struct drm_device *dev, struct drm_encoder *encoder)
 {
 	int ret;
 
-	ret = exynos_drm_crtc_get_pipe_from_type(dev, EXYNOS_DISPLAY_TYPE_LCD);
-	if (ret < 0)
-		return ret;
-
-	encoder->possible_crtcs = 1 << ret;
-
-	DRM_DEBUG_KMS("possible_crtcs = 0x%x\n", encoder->possible_crtcs);
-
 	drm_encoder_init(dev, encoder, &exynos_dpi_encoder_funcs,
 			 DRM_MODE_ENCODER_TMDS, NULL);
 
 	drm_encoder_helper_add(encoder, &exynos_dpi_encoder_helper_funcs);
 
+	ret = exynos_drm_set_possible_crtcs(encoder, EXYNOS_DISPLAY_TYPE_LCD);
+	if (ret < 0)
+		return ret;
+
 	ret = exynos_dpi_create_connector(encoder);
 	if (ret) {
 		DRM_ERROR("failed to create connector ret = %d\n", ret);

drivers/gpu/drm/exynos/exynos_drm_drv.h

@@ -91,6 +91,7 @@ struct exynos_drm_plane {
 #define EXYNOS_DRM_PLANE_CAP_DOUBLE	(1 << 0)
 #define EXYNOS_DRM_PLANE_CAP_SCALE	(1 << 1)
 #define EXYNOS_DRM_PLANE_CAP_ZPOS	(1 << 2)
+#define EXYNOS_DRM_PLANE_CAP_TILE	(1 << 3)
 
 /*
  * Exynos DRM plane configuration structure.
@@ -117,6 +118,7 @@ struct exynos_drm_plane_config {
  * @disable: disable the device
  * @enable_vblank: specific driver callback for enabling vblank interrupt.
  * @disable_vblank: specific driver callback for disabling vblank interrupt.
+ * @mode_valid: specific driver callback for mode validation
  * @atomic_check: validate state
  * @atomic_begin: prepare device to receive an update
  * @atomic_flush: mark the end of device update
@@ -132,6 +134,8 @@ struct exynos_drm_crtc_ops {
 	int (*enable_vblank)(struct exynos_drm_crtc *crtc);
 	void (*disable_vblank)(struct exynos_drm_crtc *crtc);
 	u32 (*get_vblank_counter)(struct exynos_drm_crtc *crtc);
+	enum drm_mode_status (*mode_valid)(struct exynos_drm_crtc *crtc,
+		const struct drm_display_mode *mode);
 	int (*atomic_check)(struct exynos_drm_crtc *crtc,
 			    struct drm_crtc_state *state);
 	void (*atomic_begin)(struct exynos_drm_crtc *crtc);
@@ -162,6 +166,7 @@ struct exynos_drm_crtc {
 	const struct exynos_drm_crtc_ops	*ops;
 	void				*ctx;
 	struct exynos_drm_clk		*pipe_clk;
+	bool				i80_mode : 1;
 };
 
 static inline void exynos_drm_pipe_clk_enable(struct exynos_drm_crtc *crtc,

drivers/gpu/drm/exynos/exynos_drm_dsi.c

@@ -254,7 +254,6 @@ struct exynos_dsi {
 	struct drm_encoder encoder;
 	struct mipi_dsi_host dsi_host;
 	struct drm_connector connector;
-	struct device_node *panel_node;
 	struct drm_panel *panel;
 	struct device *dev;
 
@@ -1329,12 +1328,13 @@ static int exynos_dsi_init(struct exynos_dsi *dsi)
 	return 0;
 }
 
-static int exynos_dsi_register_te_irq(struct exynos_dsi *dsi)
+static int exynos_dsi_register_te_irq(struct exynos_dsi *dsi,
+				      struct device *panel)
 {
 	int ret;
 	int te_gpio_irq;
 
-	dsi->te_gpio = of_get_named_gpio(dsi->panel_node, "te-gpios", 0);
+	dsi->te_gpio = of_get_named_gpio(panel->of_node, "te-gpios", 0);
 	if (dsi->te_gpio == -ENOENT)
 		return 0;
 
@@ -1374,85 +1374,6 @@ static void exynos_dsi_unregister_te_irq(struct exynos_dsi *dsi)
 	}
 }
 
-static int exynos_dsi_host_attach(struct mipi_dsi_host *host,
-				  struct mipi_dsi_device *device)
-{
-	struct exynos_dsi *dsi = host_to_dsi(host);
-
-	dsi->lanes = device->lanes;
-	dsi->format = device->format;
-	dsi->mode_flags = device->mode_flags;
-	dsi->panel_node = device->dev.of_node;
-
-	/*
-	 * This is a temporary solution and should be made by more generic way.
-	 *
-	 * If attached panel device is for command mode one, dsi should register
-	 * TE interrupt handler.
-	 */
-	if (!(dsi->mode_flags & MIPI_DSI_MODE_VIDEO)) {
-		int ret = exynos_dsi_register_te_irq(dsi);
-
-		if (ret)
-			return ret;
-	}
-
-	if (dsi->connector.dev)
-		drm_helper_hpd_irq_event(dsi->connector.dev);
-
-	return 0;
-}
-
-static int exynos_dsi_host_detach(struct mipi_dsi_host *host,
-				  struct mipi_dsi_device *device)
-{
-	struct exynos_dsi *dsi = host_to_dsi(host);
-
-	exynos_dsi_unregister_te_irq(dsi);
-
-	dsi->panel_node = NULL;
-
-	if (dsi->connector.dev)
-		drm_helper_hpd_irq_event(dsi->connector.dev);
-
-	return 0;
-}
-
-static ssize_t exynos_dsi_host_transfer(struct mipi_dsi_host *host,
-				        const struct mipi_dsi_msg *msg)
-{
-	struct exynos_dsi *dsi = host_to_dsi(host);
-	struct exynos_dsi_transfer xfer;
-	int ret;
-
-	if (!(dsi->state & DSIM_STATE_ENABLED))
-		return -EINVAL;
-
-	if (!(dsi->state & DSIM_STATE_INITIALIZED)) {
-		ret = exynos_dsi_init(dsi);
-		if (ret)
-			return ret;
-		dsi->state |= DSIM_STATE_INITIALIZED;
-	}
-
-	ret = mipi_dsi_create_packet(&xfer.packet, msg);
-	if (ret < 0)
-		return ret;
-
-	xfer.rx_len = msg->rx_len;
-	xfer.rx_payload = msg->rx_buf;
-	xfer.flags = msg->flags;
-
-	ret = exynos_dsi_transfer(dsi, &xfer);
-	return (ret < 0) ? ret : xfer.rx_done;
-}
-
-static const struct mipi_dsi_host_ops exynos_dsi_ops = {
-	.attach = exynos_dsi_host_attach,
-	.detach = exynos_dsi_host_detach,
-	.transfer = exynos_dsi_host_transfer,
-};
-
 static void exynos_dsi_enable(struct drm_encoder *encoder)
 {
 	struct exynos_dsi *dsi = encoder_to_dsi(encoder);
@@ -1508,25 +1429,7 @@ static void exynos_dsi_disable(struct drm_encoder *encoder)
 static enum drm_connector_status
 exynos_dsi_detect(struct drm_connector *connector, bool force)
 {
-	struct exynos_dsi *dsi = connector_to_dsi(connector);
-
-	if (!dsi->panel) {
-		dsi->panel = of_drm_find_panel(dsi->panel_node);
-		if (dsi->panel)
-			drm_panel_attach(dsi->panel, &dsi->connector);
-	} else if (!dsi->panel_node) {
-		struct drm_encoder *encoder;
-
-		encoder = platform_get_drvdata(to_platform_device(dsi->dev));
-		exynos_dsi_disable(encoder);
-		drm_panel_detach(dsi->panel);
-		dsi->panel = NULL;
-	}
-
-	if (dsi->panel)
-		return connector_status_connected;
-
-	return connector_status_disconnected;
+	return connector->status;
 }
 
 static void exynos_dsi_connector_destroy(struct drm_connector *connector)
@@ -1575,6 +1478,7 @@ static int exynos_dsi_create_connector(struct drm_encoder *encoder)
 		return ret;
 	}
 
+	connector->status = connector_status_disconnected;
 	drm_connector_helper_add(connector, &exynos_dsi_connector_helper_funcs);
 	drm_mode_connector_attach_encoder(connector, encoder);
 
@@ -1611,6 +1515,105 @@ static const struct drm_encoder_funcs exynos_dsi_encoder_funcs = {
 
 MODULE_DEVICE_TABLE(of, exynos_dsi_of_match);
 
+static int exynos_dsi_host_attach(struct mipi_dsi_host *host,
+				  struct mipi_dsi_device *device)
+{
+	struct exynos_dsi *dsi = host_to_dsi(host);
+	struct drm_device *drm = dsi->connector.dev;
+
+	/*
+	 * This is a temporary solution and should be made by more generic way.
+	 *
+	 * If attached panel device is for command mode one, dsi should register
+	 * TE interrupt handler.
+	 */
+	if (!(device->mode_flags & MIPI_DSI_MODE_VIDEO)) {
+		int ret = exynos_dsi_register_te_irq(dsi, &device->dev);
+		if (ret)
+			return ret;
+	}
+
+	mutex_lock(&drm->mode_config.mutex);
+
+	dsi->lanes = device->lanes;
+	dsi->format = device->format;
+	dsi->mode_flags = device->mode_flags;
+	dsi->panel = of_drm_find_panel(device->dev.of_node);
+	if (dsi->panel) {
+		drm_panel_attach(dsi->panel, &dsi->connector);
+		dsi->connector.status = connector_status_connected;
+	}
+	exynos_drm_crtc_get_by_type(drm, EXYNOS_DISPLAY_TYPE_LCD)->i80_mode =
+			!(dsi->mode_flags & MIPI_DSI_MODE_VIDEO);
+
+	mutex_unlock(&drm->mode_config.mutex);
+
+	if (drm->mode_config.poll_enabled)
+		drm_kms_helper_hotplug_event(drm);
+
+	return 0;
+}
+
+static int exynos_dsi_host_detach(struct mipi_dsi_host *host,
+				  struct mipi_dsi_device *device)
+{
+	struct exynos_dsi *dsi = host_to_dsi(host);
+	struct drm_device *drm = dsi->connector.dev;
+
+	mutex_lock(&drm->mode_config.mutex);
+
+	if (dsi->panel) {
+		exynos_dsi_disable(&dsi->encoder);
+		drm_panel_detach(dsi->panel);
+		dsi->panel = NULL;
+		dsi->connector.status = connector_status_disconnected;
+	}
+
+	mutex_unlock(&drm->mode_config.mutex);
+
+	if (drm->mode_config.poll_enabled)
+		drm_kms_helper_hotplug_event(drm);
+
+	exynos_dsi_unregister_te_irq(dsi);
+
+	return 0;
+}
+
+static ssize_t exynos_dsi_host_transfer(struct mipi_dsi_host *host,
+					 const struct mipi_dsi_msg *msg)
+{
+	struct exynos_dsi *dsi = host_to_dsi(host);
+	struct exynos_dsi_transfer xfer;
+	int ret;
+
+	if (!(dsi->state & DSIM_STATE_ENABLED))
+		return -EINVAL;
+
+	if (!(dsi->state & DSIM_STATE_INITIALIZED)) {
+		ret = exynos_dsi_init(dsi);
+		if (ret)
+			return ret;
+		dsi->state |= DSIM_STATE_INITIALIZED;
+	}
+
+	ret = mipi_dsi_create_packet(&xfer.packet, msg);
+	if (ret < 0)
+		return ret;
+
+	xfer.rx_len = msg->rx_len;
+	xfer.rx_payload = msg->rx_buf;
+	xfer.flags = msg->flags;
+
+	ret = exynos_dsi_transfer(dsi, &xfer);
+	return (ret < 0) ? ret : xfer.rx_done;
+}
+
+static const struct mipi_dsi_host_ops exynos_dsi_ops = {
+	.attach = exynos_dsi_host_attach,
+	.detach = exynos_dsi_host_detach,
+	.transfer = exynos_dsi_host_transfer,
+};
+
 static int exynos_dsi_of_read_u32(const struct device_node *np,
 				  const char *propname, u32 *out_value)
 {
@@ -1662,20 +1665,15 @@ static int exynos_dsi_bind(struct device *dev, struct device *master,
 	struct drm_bridge *bridge;
 	int ret;
 
-	ret = exynos_drm_crtc_get_pipe_from_type(drm_dev,
-						  EXYNOS_DISPLAY_TYPE_LCD);
-	if (ret < 0)
-		return ret;
-
-	encoder->possible_crtcs = 1 << ret;
-
-	DRM_DEBUG_KMS("possible_crtcs = 0x%x\n", encoder->possible_crtcs);
-
 	drm_encoder_init(drm_dev, encoder, &exynos_dsi_encoder_funcs,
 			 DRM_MODE_ENCODER_TMDS, NULL);
 
 	drm_encoder_helper_add(encoder, &exynos_dsi_encoder_helper_funcs);
 
+	ret = exynos_drm_set_possible_crtcs(encoder, EXYNOS_DISPLAY_TYPE_LCD);
+	if (ret < 0)
+		return ret;
+
 	ret = exynos_dsi_create_connector(encoder);
 	if (ret) {
 		DRM_ERROR("failed to create connector ret = %d\n", ret);

drivers/gpu/drm/exynos/exynos_drm_fb.c

@@ -225,4 +225,6 @@ void exynos_drm_mode_config_init(struct drm_device *dev)
 
 	dev->mode_config.funcs = &exynos_drm_mode_config_funcs;
 	dev->mode_config.helper_private = &exynos_drm_mode_config_helpers;
+
+	dev->mode_config.allow_fb_modifiers = true;
 }

drivers/gpu/drm/exynos/exynos_drm_fimd.c

@@ -583,18 +583,12 @@ static void fimd_win_set_pixfmt(struct fimd_context *ctx, unsigned int win,
 		val |= WINCONx_BURSTLEN_16WORD;
 		break;
 	case DRM_FORMAT_ARGB8888:
+	default:
 		val |= WINCON1_BPPMODE_25BPP_A1888
 			| WINCON1_BLD_PIX | WINCON1_ALPHA_SEL;
 		val |= WINCONx_WSWP;
 		val |= WINCONx_BURSTLEN_16WORD;
 		break;
-	default:
-		DRM_DEBUG_KMS("invalid pixel size so using unpacked 24bpp.\n");
-
-		val |= WINCON0_BPPMODE_24BPP_888;
-		val |= WINCONx_WSWP;
-		val |= WINCONx_BURSTLEN_16WORD;
-		break;
 	}
 
 	/*
@@ -718,13 +712,13 @@ static void fimd_update_plane(struct exynos_drm_crtc *crtc,
 	unsigned long val, size, offset;
 	unsigned int last_x, last_y, buf_offsize, line_size;
 	unsigned int win = plane->index;
-	unsigned int bpp = fb->format->cpp[0];
+	unsigned int cpp = fb->format->cpp[0];
 	unsigned int pitch = fb->pitches[0];
 
 	if (ctx->suspended)
 		return;
 
-	offset = state->src.x * bpp;
+	offset = state->src.x * cpp;
 	offset += state->src.y * pitch;
 
 	/* buffer start address */
@@ -743,8 +737,8 @@ static void fimd_update_plane(struct exynos_drm_crtc *crtc,
 			state->crtc.w, state->crtc.h);
 
 	/* buffer size */
-	buf_offsize = pitch - (state->crtc.w * bpp);
-	line_size = state->crtc.w * bpp;
+	buf_offsize = pitch - (state->crtc.w * cpp);
+	line_size = state->crtc.w * cpp;
 	val = VIDW_BUF_SIZE_OFFSET(buf_offsize) |
 		VIDW_BUF_SIZE_PAGEWIDTH(line_size) |
 		VIDW_BUF_SIZE_OFFSET_E(buf_offsize) |

drivers/gpu/drm/exynos/exynos_drm_mic.c

@@ -21,9 +21,12 @@
 #include <linux/component.h>
 #include <linux/pm_runtime.h>
 #include <drm/drmP.h>
+#include <drm/drm_encoder.h>
 #include <linux/mfd/syscon.h>
 #include <linux/regmap.h>
 
+#include "exynos_drm_drv.h"
+
 /* Sysreg registers for MIC */
 #define DSD_CFG_MUX	0x1004
 #define MIC0_RGB_MUX	(1 << 0)
@@ -85,12 +88,6 @@
 
 #define MIC_BS_SIZE_2D(x)	((x) & 0x3fff)
 
-enum {
-	ENDPOINT_DECON_NODE,
-	ENDPOINT_DSI_NODE,
-	NUM_ENDPOINTS
-};
-
 static char *clk_names[] = { "pclk_mic0", "sclk_rgb_vclk_to_mic0" };
 #define NUM_CLKS		ARRAY_SIZE(clk_names)
 static DEFINE_MUTEX(mic_mutex);
@@ -229,36 +226,6 @@ static void mic_set_reg_on(struct exynos_mic *mic, bool enable)
 	writel(reg, mic->reg + MIC_OP);
 }
 
-static int parse_dt(struct exynos_mic *mic)
-{
-	int ret = 0, i, j;
-	struct device_node *remote_node;
-	struct device_node *nodes[3];
-
-	/*
-	 * The order of endpoints does matter.
-	 * The first node must be for decon and the second one must be for dsi.
-	 */
-	for (i = 0, j = 0; i < NUM_ENDPOINTS; i++) {
-		remote_node = of_graph_get_remote_node(mic->dev->of_node, i, 0);
-		if (!remote_node) {
-			ret = -EPIPE;
-			goto exit;
-		}
-		nodes[j++] = remote_node;
-
-		if (i == ENDPOINT_DECON_NODE &&
-			of_get_child_by_name(remote_node, "i80-if-timings"))
-			mic->i80_mode = 1;
-	}
-
-exit:
-	while (--j > -1)
-		of_node_put(nodes[j]);
-
-	return ret;
-}
-
 static void mic_disable(struct drm_bridge *bridge) { }
 
 static void mic_post_disable(struct drm_bridge *bridge)
@@ -286,6 +253,7 @@ static void mic_mode_set(struct drm_bridge *bridge,
 
 	mutex_lock(&mic_mutex);
 	drm_display_mode_to_videomode(mode, &mic->vm);
+	mic->i80_mode = to_exynos_crtc(bridge->encoder->crtc)->i80_mode;
 	mutex_unlock(&mic_mutex);
 }
 
@@ -417,10 +385,6 @@ static int exynos_mic_probe(struct platform_device *pdev)
 
 	mic->dev = dev;
 
-	ret = parse_dt(mic);
-	if (ret)
-		goto err;
-
 	ret = of_address_to_resource(dev->of_node, 0, &res);
 	if (ret) {
 		DRM_ERROR("mic: Failed to get mem region for MIC\n");

drivers/gpu/drm/exynos/exynos_drm_plane.c

@@ -178,6 +178,29 @@ static struct drm_plane_funcs exynos_plane_funcs = {
 	.atomic_destroy_state = exynos_drm_plane_destroy_state,
 };
 
+static int
+exynos_drm_plane_check_format(const struct exynos_drm_plane_config *config,
+			      struct exynos_drm_plane_state *state)
+{
+	struct drm_framebuffer *fb = state->base.fb;
+
+	switch (fb->modifier) {
+	case DRM_FORMAT_MOD_SAMSUNG_64_32_TILE:
+		if (!(config->capabilities & EXYNOS_DRM_PLANE_CAP_TILE))
+			return -ENOTSUPP;
+		break;
+
+	case DRM_FORMAT_MOD_LINEAR:
+		break;
+
+	default:
+		DRM_ERROR("unsupported pixel format modifier");
+		return -ENOTSUPP;
+	}
+
+	return 0;
+}
+
 static int
 exynos_drm_plane_check_size(const struct exynos_drm_plane_config *config,
 			    struct exynos_drm_plane_state *state)
@@ -222,6 +245,10 @@ static int exynos_plane_atomic_check(struct drm_plane *plane,
 	/* translate state into exynos_state */
 	exynos_plane_mode_set(exynos_state);
 
+	ret = exynos_drm_plane_check_format(exynos_plane->config, exynos_state);
+	if (ret)
+		return ret;
+
 	ret = exynos_drm_plane_check_size(exynos_plane->config, exynos_state);
 	return ret;
 }

drivers/gpu/drm/exynos/exynos_drm_vidi.c

@@ -381,7 +381,7 @@ static int vidi_bind(struct device *dev, struct device *master, void *data)
 	struct exynos_drm_plane *exynos_plane;
 	struct exynos_drm_plane_config plane_config = { 0 };
 	unsigned int i;
-	int pipe, ret;
+	int ret;
 
 	ctx->drm_dev = drm_dev;
 
@@ -406,20 +406,15 @@ static int vidi_bind(struct device *dev, struct device *master, void *data)
 		return PTR_ERR(ctx->crtc);
 	}
 
-	pipe = exynos_drm_crtc_get_pipe_from_type(drm_dev,
-						  EXYNOS_DISPLAY_TYPE_VIDI);
-	if (pipe < 0)
-		return pipe;
-
-	encoder->possible_crtcs = 1 << pipe;
-
-	DRM_DEBUG_KMS("possible_crtcs = 0x%x\n", encoder->possible_crtcs);
-
 	drm_encoder_init(drm_dev, encoder, &exynos_vidi_encoder_funcs,
 			 DRM_MODE_ENCODER_TMDS, NULL);
 
 	drm_encoder_helper_add(encoder, &exynos_vidi_encoder_helper_funcs);
 
+	ret = exynos_drm_set_possible_crtcs(encoder, EXYNOS_DISPLAY_TYPE_VIDI);
+	if (ret < 0)
+		return ret;
+
 	ret = vidi_create_connector(encoder);
 	if (ret) {
 		DRM_ERROR("failed to create connector ret = %d\n", ret);

drivers/gpu/drm/exynos/exynos_hdmi.c

@@ -1697,32 +1697,25 @@ static int hdmi_bind(struct device *dev, struct device *master, void *data)
 	struct drm_device *drm_dev = data;
 	struct hdmi_context *hdata = dev_get_drvdata(dev);
 	struct drm_encoder *encoder = &hdata->encoder;
-	struct exynos_drm_crtc *exynos_crtc;
-	struct drm_crtc *crtc;
-	int ret, pipe;
+	struct exynos_drm_crtc *crtc;
+	int ret;
 
 	hdata->drm_dev = drm_dev;
 
-	pipe = exynos_drm_crtc_get_pipe_from_type(drm_dev,
-						  EXYNOS_DISPLAY_TYPE_HDMI);
-	if (pipe < 0)
-		return pipe;
-
 	hdata->phy_clk.enable = hdmiphy_clk_enable;
 
-	crtc = drm_crtc_from_index(drm_dev, pipe);
-	exynos_crtc = to_exynos_crtc(crtc);
-	exynos_crtc->pipe_clk = &hdata->phy_clk;
-
-	encoder->possible_crtcs = 1 << pipe;
-
-	DRM_DEBUG_KMS("possible_crtcs = 0x%x\n", encoder->possible_crtcs);
-
 	drm_encoder_init(drm_dev, encoder, &exynos_hdmi_encoder_funcs,
 			 DRM_MODE_ENCODER_TMDS, NULL);
 
 	drm_encoder_helper_add(encoder, &exynos_hdmi_encoder_helper_funcs);
 
+	ret = exynos_drm_set_possible_crtcs(encoder, EXYNOS_DISPLAY_TYPE_HDMI);
+	if (ret < 0)
+		return ret;
+
+	crtc = exynos_drm_crtc_get_by_type(drm_dev, EXYNOS_DISPLAY_TYPE_HDMI);
+	crtc->pipe_clk = &hdata->phy_clk;
+
 	ret = hdmi_create_connector(encoder);
 	if (ret) {
 		DRM_ERROR("failed to create connector ret = %d\n", ret);

drivers/gpu/drm/exynos/exynos_mixer.c

@@ -148,7 +148,8 @@ static const struct exynos_drm_plane_config plane_configs[MIXER_WIN_NR] = {
 		.pixel_formats = vp_formats,
 		.num_pixel_formats = ARRAY_SIZE(vp_formats),
 		.capabilities = EXYNOS_DRM_PLANE_CAP_SCALE |
-				EXYNOS_DRM_PLANE_CAP_ZPOS,
+				EXYNOS_DRM_PLANE_CAP_ZPOS |
+				EXYNOS_DRM_PLANE_CAP_TILE,
 	},
 };
 
@@ -483,29 +484,18 @@ static void vp_video_buffer(struct mixer_context *ctx,
 	unsigned int priority = state->base.normalized_zpos + 1;
 	unsigned long flags;
 	dma_addr_t luma_addr[2], chroma_addr[2];
-	bool tiled_mode = false;
-	bool crcb_mode = false;
+	bool is_tiled, is_nv21;
 	u32 val;
 
-	switch (fb->format->format) {
-	case DRM_FORMAT_NV12:
-		crcb_mode = false;
-		break;
-	case DRM_FORMAT_NV21:
-		crcb_mode = true;
-		break;
-	default:
-		DRM_ERROR("pixel format for vp is wrong [%d].\n",
-				fb->format->format);
-		return;
-	}
+	is_nv21 = (fb->format->format == DRM_FORMAT_NV21);
+	is_tiled = (fb->modifier == DRM_FORMAT_MOD_SAMSUNG_64_32_TILE);
 
 	luma_addr[0] = exynos_drm_fb_dma_addr(fb, 0);
 	chroma_addr[0] = exynos_drm_fb_dma_addr(fb, 1);
 
 	if (mode->flags & DRM_MODE_FLAG_INTERLACE) {
 		__set_bit(MXR_BIT_INTERLACE, &ctx->flags);
-		if (tiled_mode) {
+		if (is_tiled) {
 			luma_addr[1] = luma_addr[0] + 0x40;
 			chroma_addr[1] = chroma_addr[0] + 0x40;
 		} else {
@@ -525,14 +515,14 @@ static void vp_video_buffer(struct mixer_context *ctx,
 	vp_reg_writemask(res, VP_MODE, val, VP_MODE_LINE_SKIP);
 
 	/* setup format */
-	val = (crcb_mode ? VP_MODE_NV21 : VP_MODE_NV12);
-	val |= (tiled_mode ? VP_MODE_MEM_TILED : VP_MODE_MEM_LINEAR);
+	val = (is_nv21 ? VP_MODE_NV21 : VP_MODE_NV12);
+	val |= (is_tiled ? VP_MODE_MEM_TILED : VP_MODE_MEM_LINEAR);
 	vp_reg_writemask(res, VP_MODE, val, VP_MODE_FMT_MASK);
 
 	/* setting size of input image */
 	vp_reg_write(res, VP_IMG_SIZE_Y, VP_IMG_HSIZE(fb->pitches[0]) |
 		VP_IMG_VSIZE(fb->height));
-	/* chroma height has to reduced by 2 to avoid chroma distorions */
+	/* chroma plane for NV12/NV21 is half the height of the luma plane */
 	vp_reg_write(res, VP_IMG_SIZE_C, VP_IMG_HSIZE(fb->pitches[0]) |
 		VP_IMG_VSIZE(fb->height / 2));
 
@@ -594,7 +584,7 @@ static void mixer_graph_buffer(struct mixer_context *ctx,
 	unsigned long flags;
 	unsigned int win = plane->index;
 	unsigned int x_ratio = 0, y_ratio = 0;
-	unsigned int src_x_offset, src_y_offset, dst_x_offset, dst_y_offset;
+	unsigned int dst_x_offset, dst_y_offset;
 	dma_addr_t dma_addr;
 	unsigned int fmt;
 	u32 val;
@@ -616,12 +606,9 @@ static void mixer_graph_buffer(struct mixer_context *ctx,
 
 	case DRM_FORMAT_XRGB8888:
 	case DRM_FORMAT_ARGB8888:
+	default:
 		fmt = MXR_FORMAT_ARGB8888;
 		break;
-
-	default:
-		DRM_DEBUG_KMS("pixelformat unsupported by mixer\n");
-		return;
 	}
 
 	/* ratio is already checked by common plane code */
@@ -631,12 +618,10 @@ static void mixer_graph_buffer(struct mixer_context *ctx,
 	dst_x_offset = state->crtc.x;
 	dst_y_offset = state->crtc.y;
 
-	/* converting dma address base and source offset */
+	/* translate dma address base s.t. the source image offset is zero */
 	dma_addr = exynos_drm_fb_dma_addr(fb, 0)
 		+ (state->src.x * fb->format->cpp[0])
 		+ (state->src.y * fb->pitches[0]);
-	src_x_offset = 0;
-	src_y_offset = 0;
 
 	if (mode->flags & DRM_MODE_FLAG_INTERLACE)
 		__set_bit(MXR_BIT_INTERLACE, &ctx->flags);
@@ -667,11 +652,6 @@ static void mixer_graph_buffer(struct mixer_context *ctx,
 	val |= MXR_GRP_WH_V_SCALE(y_ratio);
 	mixer_reg_write(res, MXR_GRAPHIC_WH(win), val);
 
-	/* setup offsets in source image */
-	val  = MXR_GRP_SXY_SX(src_x_offset);
-	val |= MXR_GRP_SXY_SY(src_y_offset);
-	mixer_reg_write(res, MXR_GRAPHIC_SXY(win), val);
-
 	/* setup offsets in display image */
 	val  = MXR_GRP_DXY_DX(dst_x_offset);
 	val |= MXR_GRP_DXY_DY(dst_y_offset);
@@ -748,6 +728,10 @@ static void mixer_win_reset(struct mixer_context *ctx)
 	if (test_bit(MXR_BIT_VP_ENABLED, &ctx->flags))
 		mixer_reg_writemask(res, MXR_CFG, 0, MXR_CFG_VP_ENABLE);
 
+	/* set all source image offsets to zero */
+	mixer_reg_write(res, MXR_GRAPHIC_SXY(0), 0);
+	mixer_reg_write(res, MXR_GRAPHIC_SXY(1), 0);
+
 	spin_unlock_irqrestore(&res->reg_slock, flags);
 }