Massive merge by hand for changes duplicated independently

by Doug Ledford, hch and alan.

Documentation/filesystems/befs.txt

+BeOS filesystem for Linux
+
+Document last updated: Dec 6, 2001
+
+WARNING
+=======
+Make sure you understand that this is alpha software.  This means that the
+implementation is neither complete nor well-tested. 
+
+I DISCLAIM ALL RESPONSIBILTY FOR ANY POSSIBLE BAD EFFECTS OF THIS CODE!
+
+LICENSE
+=====
+This software is covered by the GNU General Public License. 
+See the file COPYING for the complete text of the license.
+Or the GNU website: <http://www.gnu.org/licenses/licenses.html>
+
+AUTHOR
+=====
+Current maintainer: Will Dyson <will_dyson@pobox.com>
+Has been working on the code since Aug 13, 2001. See the changelog for details.
+
+Original Author: Makoto Kato <m_kato@ga2.so-net.ne.jp>
+His orriginal code can still be found at: <http://hp.vector.co.jp/authors/VA008030/bfs/>
+Does anyone know of a more current email address for Makoto? He doesn't respond
+to the address given above...
+
+WHAT IS THIS DRIVER?
+==================
+This module implements the native filesystem of BeOS <http://www.be.com/>
+for the linux 2.4.1 and later kernels. Currently it is a read-only implementation.
+
+Which is it, BFS or BEFS?
+================
+Be, Inc said, "BeOS Filesystem is officially called BFS, not BeFS". 
+But Unixware Boot Filesystem is called bfs, too. And they are already in the
+kernel.
+Because of this nameing conflict, on Linux the BeOS filesystem is called befs.
+
+HOW TO INSTALL
+==============
+step 1.  Install the BeFS  patch into the source code tree of linux.
+
+Apply the patchfile to your kernel source tree.
+Assuming that your kernel source is in /foo/bar/linux and the patchfile is called
+patch-befs-xxx, you would do the following:
+
+	cd /foo/bar/linux
+	patch -p1 < /path/to/patch-befs-xxx
+
+if the patching step fails (i.e. there are rejected hunks), you can try to
+figure it out yourself (it shouldn't be hard), or mail the maintainer 
+(Will Dyson <will_dyson@pobox.com>) for help.
+
+step 2.  Configuretion & make kernel
+
+The linux kernel has many compile-time options. Most of them are beyond the
+scope of this document. I suggest the Kernel-HOWTO document as a good general
+reference on this topic. <http://www.linux.com/howto/Kernel-HOWTO.html>
+
+However, to use the BeFS module, you must enable it at configure time.
+
+	cd /foo/bar/linux
+	make menuconfig (or xconfig)
+
+The BeFS module is not a standard part of the linux kernel, so you must first
+enable support for experimental code under the "Code maturity level" menu.
+
+Then, under the "Filesystems" menu will be an option called "BeFS filesystem (experimental)",
+or something like that. Enable that option (it is fine to make it a module).
+
+Save your kernel configuration and then build your kernel.
+
+step 3.  Install
+
+See the kernel howto <http://www.linux.com/howto/Kernel-HOWTO.html> for
+instructions on this critical step.
+
+USING BFS
+=========
+To use the BeOS filesystem, use filesystem type 'befs'.
+
+ex)
+    mount -t befs /dev/fd0 /beos
+
+MOUNT OPTIONS
+=============
+uid=nnn        All files in the partition will be owned by user id nnn.
+gid=nnn	       All files in the partition will be in group nnn.
+iocharset=xxx  Use xxx as the name of the NLS translation table.
+debug          The driver will output debugging information to the syslog.
+
+HOW TO GET LASTEST VERSION
+==========================
+
+The latest version is currently available at:
+<http://befs-driver.sourceforge.net/>
+
+ANY KNOWN BUGS?
+===========
+As of Jan 20, 2002:
+	
+	None
+
+SPECIAL THANKS
+==============
+Dominic Giampalo ... Writing "Practical file system design with Be filesystem"
+Hiroyuki Yamada  ... Testing LinuxPPC.
+
+
+

Documentation/voyager.txt

+Running Linux on the Voyager Architecture
+=========================================
+
+For full details and current project status, see
+
+http://www.hansenpartnership.com/voyager
+
+The voyager architecture was designed by NCR in the mid 80s to be a
+fully SMP capable RAS computing architecture built around intel's 486
+chip set.  The voyager came in three levels of architectural
+sophistication: 3,4 and 5 --- 1 and 2 never made it out of prototype.
+The linux patches support only the Level 5 voyager architecture (any
+machine class 3435 and above).
+
+The Voyager Architecture
+------------------------
+
+Voyager machines consist of a Baseboard with a 386 diagnostic
+processor, a Power Supply Interface (PSI) a Primary and possibly
+Secondary Microchannel bus and between 2 and 20 voyager slots.  The
+voyager slots can be populated with memory and cpu cards (up to 4GB
+memory and from 1 486 to 32 Pentium Pro processors).  Internally, the
+voyager has a dual arbitrated system bus and a configuration and test
+bus (CAT).  The voyager bus speed is 40MHz.  Therefore (since all
+voyager cards are dual ported for each system bus) the maximum
+transfer rate is 320Mb/s but only if you have your slot configuration
+tuned (only memory cards can communicate with both busses at once, CPU
+cards utilise them one at a time).
+
+Voyager SMP
+-----------
+
+Since voyager was the first intel based SMP system, it is slightly
+more primitive than the Intel IO-APIC approach to SMP.  Voyager allows
+arbitrary interrupt routing (including processor affinity routing) of
+all 16 PC type interrupts.  However it does this by using a modified
+5259 master/slave chip set instead of an APIC bus.  Additionally,
+voyager supports Cross Processor Interrupts (CPI) equivalent to the
+APIC IPIs.  There are two routed voyager interrupt lines provided to
+each slot.
+
+Processor Cards
+---------------
+
+These come in single, dyadic and quad configurations (the quads are
+problematic--see later).  The maximum configuration is 8 quad cards
+for 32 way SMP.
+
+Quad Processors
+---------------
+
+Because voyager only supplies two interrupt lines to each Processor
+card, the Quad processors have to be configured (and Bootstrapped) in
+as a pair of Master/Slave processors.
+
+In fact, most Quad cards only accept one VIC interrupt line, so they
+have one interrupt handling processor (called the VIC extended
+processor) and three non-interrupt handling processors.
+
+Current Status
+--------------
+
+The System will boot on Mono, Dyad and Quad cards.  There was
+originally a Quad boot problem which has been fixed by proper gdt
+alignment in the initial boot loader.  If you still cannot get your
+voyager system to boot, email me at:
+
+<J.E.J.Bottomley@HansenPartnership.com>
+
+
+The Quad cards now support using the separate Quad CPI vectors instead
+of going through the VIC mailbox system.
+
+The Level 4 architecture (3430 and 3360 Machines) should also work
+fine.
+
+Dump Switch
+-----------
+
+The voyager dump switch sends out a broadcast NMI which the voyager
+code intercepts and does a task dump.
+
+Power Switch
+------------
+
+The front panel power switch is intercepted by the kernel and should
+cause a system shutdown and power off.
+
+A Note About Mixed CPU Systems
+------------------------------
+
+Linux isn't designed to handle mixed CPU systems very well.  In order
+to get everything going you *must* make sure that your lowest
+capability CPU is used for booting.  Also, mixing CPU classes
+(e.g. 486 and 586) is really not going to work very well at all.

arch/i386/kernel/apm.c

@@ -40,6 +40,7 @@
  * Nov 2000, Version 1.14
  * Oct 2001, Version 1.15
  * Jan 2002, Version 1.16
+ * Oct 2002, Version 1.16ac
  *
  * History:
  *    0.6b: first version in official kernel, Linux 1.3.46
@@ -177,6 +178,9 @@
  *         CONFIG_APM_CPU_IDLE now just affects the default value of
  *         idle_threshold (sfr).
  *         Change name of kernel apm daemon (as it no longer idles) (sfr).
+ *   1.16ac: Fix up SMP support somewhat. You can now force SMP on and we
+ *	   make _all_ APM calls on the CPU#0. Fix unsafe sign bug.
+ *	   TODO: determine if its "boot CPU" or "CPU0" we want to lock to.
  *
  * APM 1.1 Reference:
  *
@@ -250,6 +254,7 @@ extern int (*console_blank_hook)(int);
  *	    					powering off
  *	    [no-]debug			log some debugging messages
  *	    [no-]power[-_]off		power off on shutdown
+ *	    [no-]smp			Use apm even on an SMP box
  *	    bounce[-_]interval=<n>	number of ticks to ignore suspend
  *	    				bounces
  *          idle[-_]threshold=<n>       System idle percentage above which to
@@ -396,6 +401,7 @@ static long			clock_cmos_diff;
 static int			got_clock_diff;
 #endif
 static int			debug;
+static int			smp;
 static int			apm_disabled = -1;
 #ifdef CONFIG_SMP
 static int			power_off;
@@ -422,7 +428,7 @@ static struct apm_user *	user_list;
 static spinlock_t		user_list_lock = SPIN_LOCK_UNLOCKED;
 static struct desc_struct	bad_bios_desc = { 0, 0x00409200 };
 
-static char			driver_version[] = "1.16";	/* no spaces */
+static char			driver_version[] = "1.16ac";	/* no spaces */
 
 /*
  *	APM event names taken from the APM 1.2 specification. These are
@@ -498,6 +504,38 @@ static void apm_error(char *str, int err)
 			str, err);
 }
 
+/*
+ * Lock APM functionality to physical CPU 0
+ */
+ 
+#ifdef CONFIG_SMP
+
+static unsigned long apm_save_cpus(void)
+{
+	unsigned long x = current->cpus_allowed;
+	/* Some bioses don't like being called from CPU != 0 */
+	set_cpus_allowed(current, 1 << 0);
+	if (unlikely(smp_processor_id() != 0))
+		BUG();
+	return x;
+}
+
+static inline void apm_restore_cpus(unsigned long mask)
+{
+	set_cpus_allowed(current, mask);
+}
+
+#else
+
+/*
+ *	No CPU lockdown needed on a uniprocessor
+ */
+ 
+#define apm_save_cpus()	0
+#define apm_restore_cpus(x)	(void)(x)
+
+#endif
+
 /*
  * These are the actual BIOS calls.  Depending on APM_ZERO_SEGS and
  * apm_info.allow_ints, we are being really paranoid here!  Not only
@@ -571,9 +609,12 @@ static u8 apm_bios_call(u32 func, u32 ebx_in, u32 ecx_in,
 {
 	APM_DECL_SEGS
 	unsigned long		flags;
+	unsigned long		cpus;
 	int			cpu;
 	struct desc_struct	save_desc_40;
 
+	cpus = apm_save_cpus();
+	
 	cpu = get_cpu();
 	save_desc_40 = cpu_gdt_table[cpu][0x40 / 8];
 	cpu_gdt_table[cpu][0x40 / 8] = bad_bios_desc;
@@ -601,6 +642,8 @@ static u8 apm_bios_call(u32 func, u32 ebx_in, u32 ecx_in,
 	local_irq_restore(flags);
 	cpu_gdt_table[cpu][0x40 / 8] = save_desc_40;
 	put_cpu();
+	apm_restore_cpus(cpus);
+	
 	return *eax & 0xff;
 }
 
@@ -623,9 +666,13 @@ static u8 apm_bios_call_simple(u32 func, u32 ebx_in, u32 ecx_in, u32 *eax)
 	u8			error;
 	APM_DECL_SEGS
 	unsigned long		flags;
+	unsigned long		cpus;
 	int			cpu;
 	struct desc_struct	save_desc_40;
 
+
+	cpus = apm_save_cpus();
+	
 	cpu = get_cpu();
 	save_desc_40 = cpu_gdt_table[cpu][0x40 / 8];
 	cpu_gdt_table[cpu][0x40 / 8] = bad_bios_desc;
@@ -657,6 +704,7 @@ static u8 apm_bios_call_simple(u32 func, u32 ebx_in, u32 ecx_in, u32 *eax)
 	local_irq_restore(flags);
 	cpu_gdt_table[smp_processor_id()][0x40 / 8] = save_desc_40;
 	put_cpu();
+	apm_restore_cpus(cpus);
 	return error;
 }
 
@@ -772,7 +820,11 @@ static int apm_do_idle(void)
 	if (apm_bios_call_simple(APM_FUNC_IDLE, 0, 0, &eax)) {
 		static unsigned long t;
 
-		if (time_after(jiffies, t + 10 * HZ)) {
+		/* This always fails on some SMP boards running UP kernels.
+		 * Only report the failure the first 5 times.
+		 */
+		if (++t < 5)
+		{
 			printk(KERN_DEBUG "apm_do_idle failed (%d)\n",
 					(eax >> 8) & 0xff);
 			t = jiffies;
@@ -912,14 +964,16 @@ static void apm_power_off(void)
 #ifdef CONFIG_SMP
 	/* Some bioses don't like being called from CPU != 0 */
 	if (smp_processor_id() != 0) {
-		current->cpus_allowed = 1;
-		schedule();
+		set_cpus_allowed(current, 1 << 0);
 		if (unlikely(smp_processor_id() != 0))
 			BUG();
 	}
 #endif
 	if (apm_info.realmode_power_off)
+	{
+		(void)apm_save_cpus();
 		machine_real_restart(po_bios_call, sizeof(po_bios_call));
+	}
 	else
 		(void) set_system_power_state(APM_STATE_OFF);
 }
@@ -1096,6 +1150,19 @@ static int apm_console_blank(int blank)
 	}
 	if ((error == APM_SUCCESS) || (error == APM_NO_ERROR))
 		return 1;
+	if (error == APM_NOT_ENGAGED) {
+		static int tried;
+		int eng_error;
+		if (tried++ == 0) {
+			eng_error = apm_engage_power_management(APM_DEVICE_ALL, 1);
+			if (eng_error) {
+				apm_error("set display", error);
+				apm_error("engage interface", eng_error);
+				return 0;
+			} else
+				return apm_console_blank(blank);
+		}
+	}
 	apm_error("set display", error);
 	return 0;
 }
@@ -1424,7 +1491,7 @@ static ssize_t do_read(struct file *fp, char *buf, size_t count, loff_t *ppos)
 	as = fp->private_data;
 	if (check_apm_user(as, "read"))
 		return -EIO;
-	if (count < sizeof(apm_event_t))
+	if ((int)count < sizeof(apm_event_t))
 		return -EINVAL;
 	if ((queue_empty(as)) && (fp->f_flags & O_NONBLOCK))
 		return -EAGAIN;
@@ -1693,8 +1760,7 @@ static int apm(void *unused)
 	 * Method suggested by Ingo Molnar.
 	 */
 	if (smp_processor_id() != 0) {
-		current->cpus_allowed = 1;
-		schedule();
+		set_cpus_allowed(current, 1 << 0);
 		if (unlikely(smp_processor_id() != 0))
 			BUG();
 	}
@@ -1746,7 +1812,7 @@ static int apm(void *unused)
 		}
 	}
 
-	if (debug) {
+	if (debug && (num_online_cpus() == 1 || smp )) {
 		error = apm_get_power_status(&bx, &cx, &dx);
 		if (error)
 			printk(KERN_INFO "apm: power status not available\n");
@@ -1790,7 +1856,7 @@ static int apm(void *unused)
 		pm_power_off = apm_power_off;
 	register_sysrq_key('o', &sysrq_poweroff_op);
 
-	if (num_online_cpus() == 1) {
+	if (num_online_cpus() == 1 || smp) {
 #if defined(CONFIG_APM_DISPLAY_BLANK) && defined(CONFIG_VT)
 		console_blank_hook = apm_console_blank;
 #endif
@@ -1832,6 +1898,11 @@ static int __init apm_setup(char *str)
 		if ((strncmp(str, "power-off", 9) == 0) ||
 		    (strncmp(str, "power_off", 9) == 0))
 			power_off = !invert;
+		if (strncmp(str, "smp", 3) == 0)
+		{
+			smp = !invert;
+			idle_threshold = 100;
+		}
 		if ((strncmp(str, "allow-ints", 10) == 0) ||
 		    (strncmp(str, "allow_ints", 10) == 0))
  			apm_info.allow_ints = !invert;
@@ -1934,7 +2005,7 @@ static int __init apm_init(void)
 		printk(KERN_NOTICE "apm: disabled on user request.\n");
 		return -ENODEV;
 	}
-	if ((num_online_cpus() > 1) && !power_off) {
+	if ((num_online_cpus() > 1) && !power_off && !smp) {
 		printk(KERN_NOTICE "apm: disabled - APM is not SMP safe.\n");
 		return -ENODEV;
 	}
@@ -1980,6 +2051,14 @@ static int __init apm_init(void)
 				(apm_info.bios.cseg_16_len - 1) & 0xffff);
 			_set_limit((char *)&cpu_gdt_table[i][APM_DS >> 3],
 				(apm_info.bios.dseg_len - 1) & 0xffff);
+		      /* workaround for broken BIOSes */
+	                if (apm_info.bios.cseg_len <= apm_info.bios.offset)
+        	                _set_limit((char *)&cpu_gdt_table[i][APM_CS >> 3], 64 * 1024 -1);
+                       if (apm_info.bios.dseg_len <= 0x40) { /* 0x40 * 4kB == 64kB */
+                        	/* for the BIOS that assumes granularity = 1 */
+                        	cpu_gdt_table[i][APM_DS >> 3].b |= 0x800000;
+                        	printk(KERN_NOTICE "apm: we set the granularity of dseg.\n");
+        	        }
 		}
 #endif
 	}
@@ -1990,7 +2069,7 @@ static int __init apm_init(void)
 
 	kernel_thread(apm, NULL, CLONE_FS | CLONE_FILES | CLONE_SIGHAND | SIGCHLD);
 
-	if (num_online_cpus() > 1) {
+	if (num_online_cpus() > 1 && !smp ) {
 		printk(KERN_NOTICE
 		   "apm: disabled - APM is not SMP safe (power off active).\n");
 		return 0;
@@ -2058,3 +2137,7 @@ MODULE_PARM_DESC(idle_threshold,
 MODULE_PARM(idle_period, "i");
 MODULE_PARM_DESC(idle_period,
 	"Period (in sec/100) over which to caculate the idle percentage");
+MODULE_PARM(smp, "i");
+MODULE_PARM_DESC(smp,
+	"Set this to enable APM use on an SMP platform. Use with caution on older systems");
+

arch/i386/kernel/mca.c

@@ -194,10 +194,9 @@ struct resource mca_standard_resources[] = {
 
 #define MCA_STANDARD_RESOURCES	(sizeof(mca_standard_resources)/sizeof(struct resource))
 
-void __init mca_init(void)
+int __init mca_init(void)
 {
 	unsigned int i, j;
-	unsigned long flags;
 
 	/* WARNING: Be careful when making changes here. Putting an adapter
 	 * and the motherboard simultaneously into setup mode may result in
@@ -209,16 +208,16 @@ void __init mca_init(void)
 	/* Make sure the MCA bus is present */
 
 	if(!MCA_bus)
-		return;
-	printk("Micro Channel bus detected.\n");
+		return -ENODEV;
+	printk(KERN_INFO "Micro Channel bus detected.\n");
 
 	/* Allocate MCA_info structure (at address divisible by 8) */
 
 	mca_info = (struct MCA_info *)kmalloc(sizeof(struct MCA_info), GFP_KERNEL);
 
 	if(mca_info == NULL) {
-		printk("Failed to allocate memory for mca_info!");
-		return;
+		printk(KERN_ERR "Failed to allocate memory for mca_info!");
+		return -ENOMEM;
 	}
 	memset(mca_info, 0, sizeof(struct MCA_info));
 
@@ -320,6 +319,8 @@ void __init mca_init(void)
 #ifdef CONFIG_PROC_FS
 	mca_do_proc_init();
 #endif
+
+	return 0;
 }
 
 subsys_initcall(mca_init);
@@ -329,16 +330,16 @@ subsys_initcall(mca_init);
 static void mca_handle_nmi_slot(int slot, int check_flag)
 {
 	if(slot < MCA_MAX_SLOT_NR) {
-		printk("NMI: caused by MCA adapter in slot %d (%s)\n", slot+1,
+		printk(KERN_CRIT "NMI: caused by MCA adapter in slot %d (%s)\n", slot+1,
 			mca_info->slot[slot].name);
 	} else if(slot == MCA_INTEGSCSI) {
-		printk("NMI: caused by MCA integrated SCSI adapter (%s)\n",
+		printk(KERN_CRIT "NMI: caused by MCA integrated SCSI adapter (%s)\n",
 			mca_info->slot[slot].name);
 	} else if(slot == MCA_INTEGVIDEO) {
-		printk("NMI: caused by MCA integrated video adapter (%s)\n",
+		printk(KERN_CRIT "NMI: caused by MCA integrated video adapter (%s)\n",
 			mca_info->slot[slot].name);
 	} else if(slot == MCA_MOTHERBOARD) {
-		printk("NMI: caused by motherboard (%s)\n",
+		printk(KERN_CRIT "NMI: caused by motherboard (%s)\n",
 			mca_info->slot[slot].name);
 	}
 
@@ -350,7 +351,7 @@ static void mca_handle_nmi_slot(int slot, int check_flag)
 		pos6 = mca_read_pos(slot, 6);
 		pos7 = mca_read_pos(slot, 7);
 
-		printk("NMI: POS 6 = 0x%x, POS 7 = 0x%x\n", pos6, pos7);
+		printk(KERN_CRIT "NMI: POS 6 = 0x%x, POS 7 = 0x%x\n", pos6, pos7);
 	}
 
 } /* mca_handle_nmi_slot */
@@ -367,21 +368,19 @@ void mca_handle_nmi(void)
 	 * adapter was responsible for the error.
 	 */
 
-	for(i = 0; i < MCA_NUMADAPTERS; i++) {
-
-	/* Bit 7 of POS 5 is reset when this adapter has a hardware
-	 * error. Bit 7 it reset if there's error information
-	 * available in POS 6 and 7.
-	 */
-
-	pos5 = mca_read_pos(i, 5);
+	for(i = 0; i < MCA_NUMADAPTERS; i++) 
+	{
+		/* Bit 7 of POS 5 is reset when this adapter has a hardware
+		 * error. Bit 7 it reset if there's error information
+		 * available in POS 6 and 7.
+		 */
+		pos5 = mca_read_pos(i, 5);
 
-	if(!(pos5 & 0x80)) {
+		if(!(pos5 & 0x80)) {
 			mca_handle_nmi_slot(i, !(pos5 & 0x40));
 			return;
 		}
 	}
-
 	mca_nmi_hook();
 } /* mca_handle_nmi */
 

arch/i386/mach-voyager/Makefile

+#
+# Makefile for the linux kernel.
+#
+# Note! Dependencies are done automagically by 'make dep', which also
+# removes any old dependencies. DON'T put your own dependencies here
+# unless it's something special (ie not a .c file).
+#
+# Note 2! The CFLAGS definitions are now in the main makefile...
+
+EXTRA_CFLAGS	+= -I../kernel
+export-objs	:=
+
+obj-y			:= setup.o voyager_basic.o voyager_thread.o
+
+obj-$(CONFIG_SMP)	+= voyager_smp.o voyager_cat.o
+
+include $(TOPDIR)/Rules.make

arch/i386/mach-voyager/do_timer.h

+/* defines for inline arch setup functions */
+#include <asm/voyager.h>
+
+static inline void do_timer_interrupt_hook(struct pt_regs *regs)
+{
+	do_timer(regs);
+
+	voyager_timer_interrupt(regs);
+}
+
+static inline int do_timer_overflow(int count)
+{
+	/* can't read the ISR, just assume 1 tick
+	   overflow */
+	if(count > LATCH || count < 0) {
+		printk(KERN_ERR "VOYAGER PROBLEM: count is %d, latch is %d\n", count, LATCH);
+		count = LATCH;
+	}
+	count -= LATCH;
+
+	return count;
+}

arch/i386/mach-voyager/entry_arch.h

+/* -*- mode: c; c-basic-offset: 8 -*- */
+
+/* Copyright (C) 2002
+ *
+ * Author: James.Bottomley@HansenPartnership.com
+ *
+ * linux/arch/i386/voyager/entry_arch.h
+ *
+ * This file builds the VIC and QIC CPI gates
+ */
+
+/* initialise the voyager interrupt gates 
+ *
+ * This uses the macros in irq.h to set up assembly jump gates.  The
+ * calls are then redirected to the same routine with smp_ prefixed */
+BUILD_INTERRUPT(vic_sys_interrupt, VIC_SYS_INT)
+BUILD_INTERRUPT(vic_cmn_interrupt, VIC_CMN_INT)
+BUILD_INTERRUPT(vic_cpi_interrupt, VIC_CPI_LEVEL0);
+
+/* do all the QIC interrupts */
+BUILD_INTERRUPT(qic_timer_interrupt, QIC_TIMER_CPI);
+BUILD_INTERRUPT(qic_invalidate_interrupt, QIC_INVALIDATE_CPI);
+BUILD_INTERRUPT(qic_reschedule_interrupt, QIC_RESCHEDULE_CPI);
+BUILD_INTERRUPT(qic_enable_irq_interrupt, QIC_ENABLE_IRQ_CPI);
+BUILD_INTERRUPT(qic_call_function_interrupt, QIC_CALL_FUNCTION_CPI);
+

arch/i386/mach-voyager/irq_vectors.h

+/* -*- mode: c; c-basic-offset: 8 -*- */
+
+/* Copyright (C) 2002
+ *
+ * Author: James.Bottomley@HansenPartnership.com
+ *
+ * linux/arch/i386/voyager/irq_vectors.h
+ *
+ * This file provides definitions for the VIC and QIC CPIs
+ */
+
+#ifndef _ASM_IRQ_VECTORS_H
+#define _ASM_IRQ_VECTORS_H
+
+/*
+ * IDT vectors usable for external interrupt sources start
+ * at 0x20:
+ */
+#define FIRST_EXTERNAL_VECTOR	0x20
+
+#define SYSCALL_VECTOR		0x80
+
+/*
+ * Vectors 0x20-0x2f are used for ISA interrupts.
+ */
+
+/* These define the CPIs we use in linux */
+#define VIC_CPI_LEVEL0			0
+#define VIC_CPI_LEVEL1			1
+/* now the fake CPIs */
+#define VIC_TIMER_CPI			2
+#define VIC_INVALIDATE_CPI		3
+#define VIC_RESCHEDULE_CPI		4
+#define VIC_ENABLE_IRQ_CPI		5
+#define VIC_CALL_FUNCTION_CPI		6
+
+/* Now the QIC CPIs:  Since we don't need the two initial levels,
+ * these are 2 less than the VIC CPIs */
+#define QIC_CPI_OFFSET			1
+#define QIC_TIMER_CPI			(VIC_TIMER_CPI - QIC_CPI_OFFSET)
+#define QIC_INVALIDATE_CPI		(VIC_INVALIDATE_CPI - QIC_CPI_OFFSET)
+#define QIC_RESCHEDULE_CPI		(VIC_RESCHEDULE_CPI - QIC_CPI_OFFSET)
+#define QIC_ENABLE_IRQ_CPI		(VIC_ENABLE_IRQ_CPI - QIC_CPI_OFFSET)
+#define QIC_CALL_FUNCTION_CPI		(VIC_CALL_FUNCTION_CPI - QIC_CPI_OFFSET)
+
+#define VIC_START_FAKE_CPI		VIC_TIMER_CPI
+#define VIC_END_FAKE_CPI		VIC_CALL_FUNCTION_CPI
+
+/* this is the SYS_INT CPI. */
+#define VIC_SYS_INT			8
+#define VIC_CMN_INT			15
+
+/* This is the boot CPI for alternate processors.  It gets overwritten
+ * by the above once the system has activated all available processors */
+#define VIC_CPU_BOOT_CPI		VIC_CPI_LEVEL0
+#define VIC_CPU_BOOT_ERRATA_CPI		(VIC_CPI_LEVEL0 + 8)
+
+#define NR_IRQS 224
+
+#ifndef __ASSEMBLY__
+extern asmlinkage void vic_cpi_interrupt(void);
+extern asmlinkage void vic_sys_interrupt(void);
+extern asmlinkage void vic_cmn_interrupt(void);
+extern asmlinkage void qic_timer_interrupt(void);
+extern asmlinkage void qic_invalidate_interrupt(void);
+extern asmlinkage void qic_reschedule_interrupt(void);
+extern asmlinkage void qic_enable_irq_interrupt(void);
+extern asmlinkage void qic_call_function_interrupt(void);
+#endif /* !__ASSEMBLY__ */
+
+#endif /* _ASM_IRQ_VECTORS_H */

arch/i386/mach-voyager/setup.c

+/*
+ *	Machine specific setup for generic
+ */
+
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <asm/arch_hooks.h>
+
+void __init pre_intr_init_hook(void)
+{
+	init_ISA_irqs();
+}
+
+/*
+ * IRQ2 is cascade interrupt to second interrupt controller
+ */
+static struct irqaction irq2 = { no_action, 0, 0, "cascade", NULL, NULL};
+
+void __init intr_init_hook(void)
+{
+#ifdef CONFIG_SMP
+	smp_intr_init();
+#endif
+
+	setup_irq(2, &irq2);
+}
+
+void __init pre_setup_arch_hook(void)
+{
+}
+
+void __init trap_init_hook(void)
+{
+}
+
+static struct irqaction irq0  = { timer_interrupt, SA_INTERRUPT, 0, "timer", NULL, NULL};
+
+void __init time_init_hook(void)
+{
+	setup_irq(0, &irq0);
+}

arch/i386/mach-voyager/setup_arch_post.h

+/* Hook for machine specific memory setup.
+ *
+ * This is included late in kernel/setup.c so that it can make use of all of
+ * the static functions. */
+
+static inline char * __init machine_specific_memory_setup(void)
+{
+	char *who;
+
+	who = "NOT VOYAGER";
+
+	if(voyager_level == 5) {
+		__u32 addr, length;
+		int i;
+
+		who = "Voyager-SUS";
+
+		e820.nr_map = 0;
+		for(i=0; voyager_memory_detect(i, &addr, &length); i++) {
+			add_memory_region(addr, length, E820_RAM);
+		}
+		return who;
+	} else if(voyager_level == 4) {
+		__u32 tom;
+		__u16 catbase = inb(VOYAGER_SSPB_RELOCATION_PORT)<<8;
+		/* select the DINO config space */
+		outb(VOYAGER_DINO, VOYAGER_CAT_CONFIG_PORT);
+		/* Read DINO top of memory register */
+		tom = ((inb(catbase + 0x4) & 0xf0) << 16)
+			+ ((inb(catbase + 0x5) & 0x7f) << 24);
+
+		if(inb(catbase) != VOYAGER_DINO) {
+			printk(KERN_ERR "Voyager: Failed to get DINO for L4, setting tom to EXT_MEM_K\n");
+			tom = (EXT_MEM_K)<<10;
+		}
+		who = "Voyager-TOM";
+		add_memory_region(0, 0x9f000, E820_RAM);
+		/* map from 1M to top of memory */
+		add_memory_region(1*1024*1024, tom - 1*1024*1024, E820_RAM);
+		/* FIXME: Should check the ASICs to see if I need to
+		 * take out the 8M window.  Just do it at the moment
+		 * */
+		add_memory_region(8*1024*1024, 8*1024*1024, E820_RESERVED);
+		return who;
+	}
+
+	who = "BIOS-e820";
+
+	/*
+	 * Try to copy the BIOS-supplied E820-map.
+	 *
+	 * Otherwise fake a memory map; one section from 0k->640k,
+	 * the next section from 1mb->appropriate_mem_k
+	 */
+	sanitize_e820_map(E820_MAP, &E820_MAP_NR);
+	if (copy_e820_map(E820_MAP, E820_MAP_NR) < 0) {
+		unsigned long mem_size;
+
+		/* compare results from other methods and take the greater */
+		if (ALT_MEM_K < EXT_MEM_K) {
+			mem_size = EXT_MEM_K;
+			who = "BIOS-88";
+		} else {
+			mem_size = ALT_MEM_K;
+			who = "BIOS-e801";
+		}
+
+		e820.nr_map = 0;
+		add_memory_region(0, LOWMEMSIZE(), E820_RAM);
+		add_memory_region(HIGH_MEMORY, mem_size << 10, E820_RAM);
+  	}
+	return who;
+}

arch/i386/mach-voyager/setup_arch_pre.h

+#include <asm/voyager.h>
+#define VOYAGER_BIOS_INFO ((struct voyager_bios_info *)(PARAM+0x40))
+
+/* Hook to call BIOS initialisation function */
+
+/* for voyager, pass the voyager BIOS/SUS info area to the detection 
+ * routines */
+
+#define ARCH_SETUP	voyager_detect(VOYAGER_BIOS_INFO);
+

arch/i386/mach-voyager/voyager_basic.c

+/* Copyright (C) 1999,2001 
+ *
+ * Author: J.E.J.Bottomley@HansenPartnership.com
+ *
+ * linux/arch/i386/kernel/voyager.c
+ *
+ * This file contains all the voyager specific routines for getting
+ * initialisation of the architecture to function.  For additional
+ * features see:
+ *
+ *	voyager_cat.c - Voyager CAT bus interface
+ *	voyager_smp.c - Voyager SMP hal (emulates linux smp.c)
+ */
+
+#include <linux/config.h>
+#include <linux/types.h>
+#include <linux/sched.h>
+#include <linux/ptrace.h>
+#include <linux/ioport.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/reboot.h>
+#include <asm/io.h>
+#include <asm/pgalloc.h>
+#include <asm/voyager.h>
+#include <asm/vic.h>
+#include <linux/pm.h>
+#include <linux/irq.h>
+#include <asm/tlbflush.h>
+#include <asm/arch_hooks.h>
+
+/*
+ * Power off function, if any
+ */
+void (*pm_power_off)(void);
+
+int reboot_thru_bios;
+
+int voyager_level = 0;
+
+struct voyager_SUS *voyager_SUS = NULL;
+
+void
+voyager_detect(struct voyager_bios_info *bios)
+{
+	if(bios->len != 0xff) {
+		int class = (bios->class_1 << 8) 
+			| (bios->class_2 & 0xff);
+
+		printk("Voyager System detected.\n"
+		       "        Class %x, Revision %d.%d\n",
+		       class, bios->major, bios->minor);
+		if(class == VOYAGER_LEVEL4) 
+			voyager_level = 4;
+		else if(class < VOYAGER_LEVEL5_AND_ABOVE)
+			voyager_level = 3;
+		else
+			voyager_level = 5;
+		printk("        Architecture Level %d\n", voyager_level);
+		if(voyager_level < 4)
+			printk("\n**WARNING**: Voyager HAL only supports Levels 4 and 5 Architectures at the moment\n\n");
+		/* install the power off handler */
+		pm_power_off = voyager_power_off;
+	} else {
+		printk("\n\n**WARNING**: No Voyager Subsystem Found\n");
+	}
+}
+
+void
+voyager_system_interrupt(int cpl, void *dev_id, struct pt_regs *regs)
+{
+	printk("Voyager: detected system interrupt\n");
+}
+
+/* Routine to read information from the extended CMOS area */
+__u8
+voyager_extended_cmos_read(__u16 addr)
+{
+	outb(addr & 0xff, 0x74);
+	outb((addr >> 8) & 0xff, 0x75);
+	return inb(0x76);
+}
+
+/* internal definitions for the SUS Click Map of memory */
+
+#define CLICK_ENTRIES	16
+#define CLICK_SIZE	4096	/* click to byte conversion for Length */
+
+typedef struct ClickMap {
+	struct Entry {
+		__u32	Address;
+		__u32	Length;
+	} Entry[CLICK_ENTRIES];
+} ClickMap_t;
+
+
+/* This routine is pretty much an awful hack to read the bios clickmap by
+ * mapping it into page 0.  There are usually three regions in the map:
+ * 	Base Memory
+ * 	Extended Memory
+ *	zero length marker for end of map
+ *
+ * Returns are 0 for failure and 1 for success on extracting region.
+ */
+int __init
+voyager_memory_detect(int region, __u32 *start, __u32 *length)
+{
+	int i;
+	int retval = 0;
+	__u8 cmos[4];
+	ClickMap_t *map;
+	unsigned long map_addr;
+	unsigned long old;
+
+	if(region >= CLICK_ENTRIES) {
+		printk("Voyager: Illegal ClickMap region %d\n", region);
+		return 0;
+	}
+
+	for(i = 0; i < sizeof(cmos); i++)
+		cmos[i] = voyager_extended_cmos_read(VOYAGER_MEMORY_CLICKMAP + i);
+
+	map_addr = *(unsigned long *)cmos;
+
+	/* steal page 0 for this */
+	old = pg0[0];
+	pg0[0] = ((map_addr & PAGE_MASK) | _PAGE_RW | _PAGE_PRESENT);
+	local_flush_tlb();
+	/* now clear everything out but page 0 */
+	map = (ClickMap_t *)(map_addr & (~PAGE_MASK));
+
+	/* zero length is the end of the clickmap */
+	if(map->Entry[region].Length != 0) {
+		*length = map->Entry[region].Length * CLICK_SIZE;
+		*start = map->Entry[region].Address;
+		retval = 1;
+	}
+
+	/* replace the mapping */
+	pg0[0] = old;
+	local_flush_tlb();
+	return retval;
+}
+
+void
+voyager_dump()
+{
+	/* get here via a sysrq */
+#ifdef CONFIG_SMP
+	voyager_smp_dump();
+#endif
+}
+
+/* voyager specific handling code for timer interrupts.  Used to hand
+ * off the timer tick to the SMP code, since the VIC doesn't have an
+ * internal timer (The QIC does, but that's another story). */
+void
+voyager_timer_interrupt(struct pt_regs *regs)
+{
+	if((jiffies & 0x3ff) == 0) {
+
+		/* There seems to be something flaky in either
+		 * hardware or software that is resetting the timer 0
+		 * count to something much higher than it should be
+		 * This seems to occur in the boot sequence, just
+		 * before root is mounted.  Therefore, every 10
+		 * seconds or so, we sanity check the timer zero count
+		 * and kick it back to where it should be.
+		 *
+		 * FIXME: This is the most awful hack yet seen.  I
+		 * should work out exactly what is interfering with
+		 * the timer count settings early in the boot sequence
+		 * and swiftly introduce it to something sharp and
+		 * pointy.  */
+		__u16 val;
+		extern spinlock_t i8253_lock;
+
+		spin_lock(&i8253_lock);
+		
+		outb_p(0x00, 0x43);
+		val = inb_p(0x40);
+		val |= inb(0x40) << 8;
+		spin_unlock(&i8253_lock);
+
+		if(val > LATCH) {
+			printk("\nVOYAGER: countdown timer value too high (%d), resetting\n\n", val);
+			spin_lock(&i8253_lock);
+			outb(0x34,0x43);
+			outb_p(LATCH & 0xff , 0x40);	/* LSB */
+			outb(LATCH >> 8 , 0x40);	/* MSB */
+			spin_unlock(&i8253_lock);
+		}
+	}
+#ifdef CONFIG_SMP
+	smp_vic_timer_interrupt(regs);
+#endif
+}
+
+void
+voyager_power_off(void)
+{
+	printk("VOYAGER Power Off\n");
+
+	if(voyager_level == 5) {
+		voyager_cat_power_off();
+	} else if(voyager_level == 4) {
+		/* This doesn't apparently work on most L4 machines,
+		 * but the specs say to do this to get automatic power
+		 * off.  Unfortunately, if it doesn't power off the
+		 * machine, it ends up doing a cold restart, which
+		 * isn't really intended, so comment out the code */
+#if 0
+		int port;
+
+	  
+		/* enable the voyager Configuration Space */
+		outb((inb(VOYAGER_MC_SETUP) & 0xf0) | 0x8, 
+		     VOYAGER_MC_SETUP);
+		/* the port for the power off flag is an offset from the
+		   floating base */
+		port = (inb(VOYAGER_SSPB_RELOCATION_PORT) << 8) + 0x21;
+		/* set the power off flag */
+		outb(inb(port) | 0x1, port);
+#endif
+	}
+	/* and wait for it to happen */
+	for(;;) {
+		__asm("cli");
+		__asm("hlt");
+	}
+}
+
+/* copied from process.c */
+static inline void
+kb_wait(void)
+{
+	int i;
+
+	for (i=0; i<0x10000; i++)
+		if ((inb_p(0x64) & 0x02) == 0)
+			break;
+}
+
+void
+machine_restart(char *cmd)
+{
+	printk("Voyager Warm Restart\n");
+	kb_wait();
+
+	if(voyager_level == 5) {
+		/* write magic values to the RTC to inform system that
+		 * shutdown is beginning */
+		outb(0x8f, 0x70);
+		outb(0x5 , 0x71);
+		
+		udelay(50);
+		outb(0xfe,0x64);         /* pull reset low */
+	} else if(voyager_level == 4) {
+		__u16 catbase = inb(VOYAGER_SSPB_RELOCATION_PORT)<<8;
+		__u8 basebd = inb(VOYAGER_MC_SETUP);
+		
+		outb(basebd | 0x08, VOYAGER_MC_SETUP);
+		outb(0x02, catbase + 0x21);
+	}
+	for(;;) {
+		asm("cli");
+		asm("hlt");
+	}
+}
+
+void
+mca_nmi_hook(void)
+{
+	__u8 dumpval __attribute__((unused)) = inb(0xf823);
+	__u8 swnmi __attribute__((unused)) = inb(0xf813);
+	extern void show_stack(unsigned long *);
+
+	/* FIXME: assume dump switch pressed */
+	/* check to see if the dump switch was pressed */
+	VDEBUG(("VOYAGER: dumpval = 0x%x, swnmi = 0x%x\n", dumpval, swnmi));
+	/* clear swnmi */
+	outb(0xff, 0xf813);
+	/* tell SUS to ignore dump */
+	if(voyager_level == 5 && voyager_SUS != NULL) {
+		if(voyager_SUS->SUS_mbox == VOYAGER_DUMP_BUTTON_NMI) {
+			voyager_SUS->kernel_mbox = VOYAGER_NO_COMMAND;
+			voyager_SUS->kernel_flags |= VOYAGER_OS_IN_PROGRESS;
+			udelay(1000);
+			voyager_SUS->kernel_mbox = VOYAGER_IGNORE_DUMP;
+			voyager_SUS->kernel_flags &= ~VOYAGER_OS_IN_PROGRESS;
+		}
+	}
+	printk(KERN_ERR "VOYAGER: Dump switch pressed, printing CPU%d tracebacks\n", smp_processor_id());
+	show_stack(NULL);
+	show_state();
+}
+
+
+
+void
+machine_halt(void)
+{
+	/* treat a halt like a power off */
+	machine_power_off();
+}
+
+void machine_power_off(void)
+{
+	if (pm_power_off)
+		pm_power_off();
+}

arch/i386/mach-voyager/voyager_thread.c

+/* -*- mode: c; c-basic-offset: 8 -*- */
+
+/* Copyright (C) 2001
+ *
+ * Author: J.E.J.Bottomley@HansenPartnership.com
+ *
+ * linux/arch/i386/kernel/voyager_thread.c
+ *
+ * This module provides the machine status monitor thread for the
+ * voyager architecture.  This allows us to monitor the machine
+ * environment (temp, voltage, fan function) and the front panel and
+ * internal UPS.  If a fault is detected, this thread takes corrective
+ * action (usually just informing init)
+ * */
+
+#include <linux/module.h>
+#include <linux/config.h>
+#include <linux/mm.h>
+#include <linux/kernel_stat.h>
+#include <linux/delay.h>
+#include <linux/mc146818rtc.h>
+#include <linux/smp_lock.h>
+#include <linux/init.h>
+#include <linux/bootmem.h>
+#include <linux/kmod.h>
+#include <linux/completion.h>
+#include <linux/sched.h>
+#include <asm/desc.h>
+#include <asm/voyager.h>
+#include <asm/vic.h>
+#include <asm/pgalloc.h>
+#include <asm/mtrr.h>
+#include <asm/msr.h>
+
+#include <linux/irq.h>
+
+#define THREAD_NAME "kvoyagerd"
+
+/* external variables */
+int kvoyagerd_running = 0;
+DECLARE_MUTEX_LOCKED(kvoyagerd_sem);
+
+static int thread(void *);
+
+static __u8 set_timeout = 0;
+
+/* Start the machine monitor thread.  Return 1 if OK, 0 if fail */
+static int __init
+voyager_thread_start(void)
+{
+	if(kernel_thread(thread, NULL, CLONE_KERNEL) < 0) {
+		/* This is serious, but not fatal */
+		printk(KERN_ERR "Voyager: Failed to create system monitor thread!!!\n");
+		return 1;
+	}
+	return 0;
+}
+
+static int
+execute_helper(void *string)
+{
+	int ret;
+
+	char *envp[] = {
+		"HOME=/",
+		"TERM=linux",
+		"PATH=/sbin:/usr/sbin:/bin:/usr/bin",
+		NULL,
+	};
+	char *argv[] = {
+		"/bin/bash",
+		"-c",
+		(char *)string,
+		NULL,
+	};
+
+	if((ret = exec_usermodehelper(argv[0], argv, envp)) < 0) {
+		printk(KERN_ERR "Voyager failed to execute \"%s\"\n",
+		       (char *)string);
+	}
+	return ret;
+}
+
+static void
+execute(char *string)
+{
+	if(kernel_thread(execute_helper, (void *)string, CLONE_VFORK | SIGCHLD) < 0) {
+		printk(KERN_ERR "Voyager failed to fork before exec of \"%s\"\n",
+		       string);
+	}
+}
+
+static void
+check_from_kernel(void)
+{
+	if(voyager_status.switch_off) {
+		
+		/* FIXME: This should be configureable via proc */
+		execute("umask 600; echo 0 > /etc/initrunlvl; kill -HUP 1");
+	} else if(voyager_status.power_fail) {
+		VDEBUG(("Voyager daemon detected AC power failure\n"));
+		
+		/* FIXME: This should be configureable via proc */
+		execute("umask 600; echo F > /etc/powerstatus; kill -PWR 1");
+		set_timeout = 1;
+	}
+}
+
+static void
+check_continuing_condition(void)
+{
+	if(voyager_status.power_fail) {
+		__u8 data;
+		voyager_cat_psi(VOYAGER_PSI_SUBREAD, 
+				VOYAGER_PSI_AC_FAIL_REG, &data);
+		if((data & 0x1f) == 0) {
+			/* all power restored */
+			printk(KERN_NOTICE "VOYAGER AC power restored, cancelling shutdown\n");
+			/* FIXME: should be user configureable */
+			execute("umask 600; echo O > /etc/powerstatus; kill -PWR 1");
+			set_timeout = 0;
+		}
+	}
+}
+
+static void
+wakeup(unsigned long unused)
+{
+	up(&kvoyagerd_sem);
+}
+
+static int
+thread(void *unused)
+{
+	struct timer_list wakeup_timer;
+
+	kvoyagerd_running = 1;
+
+	reparent_to_init();
+	daemonize();
+
+	set_timeout = 0;
+
+	init_timer(&wakeup_timer);
+
+	strcpy(current->comm, THREAD_NAME);
+	sigfillset(&current->blocked);
+	current->tty = NULL;	/* get rid of controlling tty */
+
+	printk(KERN_NOTICE "Voyager starting monitor thread\n");
+
+	for(;;) {
+		down_interruptible(&kvoyagerd_sem);
+		VDEBUG(("Voyager Daemon awoken\n"));
+		if(voyager_status.request_from_kernel == 0) {
+			/* probably awoken from timeout */
+			check_continuing_condition();
+		} else {
+			check_from_kernel();
+			voyager_status.request_from_kernel = 0;
+		}
+		if(set_timeout) {
+			del_timer(&wakeup_timer);
+			wakeup_timer.expires = HZ + jiffies;
+			wakeup_timer.function = wakeup;
+			add_timer(&wakeup_timer);
+		}
+	}
+}
+
+static void __exit
+voyager_thread_stop(void)
+{
+	/* FIXME: do nothing at the moment */
+}
+
+module_init(voyager_thread_start);
+//module_exit(voyager_thread_stop);

arch/ia64/Config.help

@@ -157,6 +157,11 @@ CONFIG_PCMCIA
   and ds.o.  If you want to compile it as a module, say M here and
   read <file:Documentation/modules.txt>.
 
+CONFIG_KALLSYMS
+  Say Y here to let the kernel print out symbolic crash information and
+  symbolic stack backtraces. This increases the size of the kernel
+  somewhat, as all symbols have to be loaded into the kernel image.
+
 CONFIG_KCORE_ELF
   If you enabled support for /proc file system then the file
   /proc/kcore will contain the kernel core image. This can be used

arch/ia64/Makefile

@@ -33,44 +33,48 @@ ifeq ($(CONFIG_ITANIUM_BSTEP_SPECIFIC),y)
 	CFLAGS += -mb-step
 endif
 
-HEAD := arch/$(ARCH)/kernel/head.o arch/ia64/kernel/init_task.o
+HEAD := arch/$(ARCH)/kernel/head.o arch/$(ARCH)/kernel/init_task.o
 
-core-$(CONFIG_IA64_GENERIC) 	+= arch/$(ARCH)/hp/	  arch/$(ARCH)/dig/
-core-$(CONFIG_IA64_HP_SIM)	+= arch/$(ARCH)/hp/
-core-$(CONFIG_IA64_HP_ZX1)	+= arch/$(ARCH)/hp/ 	  arch/$(ARCH)/dig/
-core-$(CONFIG_IA64_SGI_SN)	+= arch/$(ARCH)/sn/kernel arch/$(ARCH)/sn/io
+libs-y				+= arch/$(ARCH)/lib/
+core-y				+= arch/$(ARCH)/kernel/ arch/$(ARCH)/mm/
+core-$(CONFIG_IA32_SUPPORT)	+= arch/$(ARCH)/ia32/
 core-$(CONFIG_IA64_DIG) 	+= arch/$(ARCH)/dig/
+core-$(CONFIG_IA64_GENERIC) 	+= arch/$(ARCH)/dig/ arch/$(ARCH)/hp/common/ arch/$(ARCH)/hp/zx1/ \
+				   arch/$(ARCH)/hp/sim/
+core-$(CONFIG_IA64_HP_ZX1)	+= arch/$(ARCH)/dig/
+core-$(CONFIG_IA64_SGI_SN)	+= arch/$(ARCH)/sn/kernel arch/$(ARCH)/sn/io \
+				   arch/$(ARCH)/sn/fakeprom
+drivers-$(CONFIG_PCI)		+= arch/$(ARCH)/pci/
+drivers-$(CONFIG_IA64_HP_SIM)	+= arch/$(ARCH)/hp/sim/
+drivers-$(CONFIG_IA64_HP_ZX1)	+= arch/$(ARCH)/hp/common/ arch/$(ARCH)/hp/zx1/
 
 ifdef CONFIG_IA64_SGI_SN
 	CFLAGS			+= -DBRINGUP
         SUBDIRS         	+= arch/$(ARCH)/sn/fakeprom
 endif
 
-core-$(CONFIG_IA32_SUPPORT)	+= arch/$(ARCH)/ia32/
+makeboot = $(call descend,arch/ia64/boot,$(1))
+maketool = $(call descend,arch/ia64/tools,$(1))
 
-libs-y				+= arch/$(ARCH)/lib/
-core-y				+= arch/$(ARCH)/kernel/ arch/$(ARCH)/mm/
-drivers-$(CONFIG_PCI)		+= arch/$(ARCH)/pci/
-drivers-$(CONFIG_IA64_HP_ZX1)	+= arch/$(ARCH)/hp/common/ arch/$(ARCH)/hp/zx1/
+.PHONY: compressed archclean archmrproper $(TOPDIR)/include/asm-ia64/offsets.h
+
+all: compressed boot
 
-MAKEBOOT = $(MAKE) -C arch/$(ARCH)/boot
+boot: vmlinux
+	+@$(call makeboot,all)
 
 compressed: vmlinux
 	$(OBJCOPY) $(OBJCOPYFLAGS) vmlinux vmlinux-tmp
 	gzip vmlinux-tmp
 	mv vmlinux-tmp.gz vmlinux.gz
 
-rawboot:
-	@$(MAKEBOOT) rawboot
-
 archclean:
-	@$(MAKEBOOT) clean
+	$(MAKE) -rR -f scripts/Makefile.clean obj=arch/$(ARCH)/boot
 
 archmrproper:
-	@$(MAKE) -C arch/$(ARCH)/tools mrproper
 
 prepare: $(TOPDIR)/include/asm-ia64/offsets.h
 
 $(TOPDIR)/include/asm-ia64/offsets.h: include/asm include/linux/version.h \
 				      include/config/MARKER
-	@$(MAKE) -C arch/$(ARCH)/tools $@
+	+@$(call maketool,$@)

arch/ia64/boot/Makefile

@@ -8,9 +8,9 @@
 # Copyright (C) 1998 by David Mosberger-Tang <davidm@hpl.hp.com>
 #
 
-LINKFLAGS = -static -T bootloader.lds
+LINKFLAGS = -static -T $(src)/bootloader.lds
 
-OBJECTS	= bootloader.o
+OBJS	= $(obj)/bootloader.o
 
 targets-$(CONFIG_IA64_HP_SIM)	+= bootloader
 targets-$(CONFIG_IA64_GENERIC)	+= bootloader
@@ -19,8 +19,8 @@ CFLAGS	:= $(CFLAGS) $(CFLAGS_KERNEL)
 
 all:	$(targets-y)
 
-bootloader: $(OBJECTS)
-	$(LD) $(LINKFLAGS) $(OBJECTS) $(TOPDIR)/lib/lib.a $(TOPDIR)/arch/$(ARCH)/lib/lib.a \
+bootloader: $(OBJS)
+	$(LD) $(LINKFLAGS) $(OBJS) $(TOPDIR)/lib/lib.a $(TOPDIR)/arch/$(ARCH)/lib/lib.a \
 	-o bootloader
 
 clean:

arch/ia64/config.in

@@ -66,6 +66,10 @@ fi
 
 if [ "$CONFIG_IA64_GENERIC" = "y" -o "$CONFIG_IA64_DIG" = "y" -o "$CONFIG_IA64_HP_ZX1" = "y" ];
 then
+	bool '  Enable NUMA support' CONFIG_NUMA
+	if [ "$CONFIG_NUMA" = "y" ]; then
+		define_bool CONFIG_DISCONTIGMEM y
+	fi
 	bool '  Enable IA-64 Machine Check Abort' CONFIG_IA64_MCA
 	define_bool CONFIG_PM y
 	define_bool CONFIG_IOSAPIC y
@@ -267,6 +271,7 @@ choice 'Physical memory granularity'				\
 
 bool 'Kernel debugging' CONFIG_DEBUG_KERNEL
 if [ "$CONFIG_DEBUG_KERNEL" != "n" ]; then
+   bool '  Load all symbols for debugging/kksymoops' CONFIG_KALLSYMS
    bool '  Print possible IA64 hazards to console' CONFIG_IA64_PRINT_HAZARDS
    bool '  Disable VHPT' CONFIG_DISABLE_VHPT
    bool '  Magic SysRq key' CONFIG_MAGIC_SYSRQ

arch/ia64/hp/Makefile

-# arch/ia64/hp/Makefile
-# Copyright (c) 2002 Matthew Wilcox for Hewlett Packard
-
-obj-$(CONFIG_IA64_GENERIC)	+= sim/ zx1/ common/
-obj-$(CONFIG_IA64_HP_SIM)	+= sim/
-
-include $(TOPDIR)/Rules.make

arch/ia64/hp/sim/simscsi.c

@@ -359,7 +359,9 @@ simscsi_queuecommand (Scsi_Cmnd *sc, void (*done)(Scsi_Cmnd *))
 			break;
 
 		      case MODE_SENSE:
-			printk("MODE_SENSE\n");
+			/* sd.c uses this to determine whether disk does write-caching. */
+			memset(sc->request_buffer, 0, 128);
+			sc->result = GOOD;
 			break;
 
 		      case START_STOP:
@@ -389,6 +391,4 @@ simscsi_queuecommand (Scsi_Cmnd *sc, void (*done)(Scsi_Cmnd *))
 
 static Scsi_Host_Template driver_template = SIMSCSI;
 
-#define __initcall(fn)	late_initcall(fn)
-
 #include "../drivers/scsi/scsi_module.c"

arch/ia64/hp/sim/simserial.c

@@ -752,8 +752,7 @@ static int get_async_struct(int line, struct async_struct **ret_info)
 	info->flags = sstate->flags;
 	info->xmit_fifo_size = sstate->xmit_fifo_size;
 	info->line = line;
-	info->tqueue.routine = do_softint;
-	info->tqueue.data = info;
+	INIT_WORK(&info->work, do_softint, info);
 	info->state = sstate;
 	if (sstate->info) {
 		kfree(info);

arch/ia64/ia32/ia32_ioctl.c

@@ -26,6 +26,12 @@
 #include <linux/if_ppp.h>
 #include <linux/ixjuser.h>
 #include <linux/i2o-dev.h>
+#include <scsi/scsi.h>
+/* Ugly hack. */
+#undef	__KERNEL__
+#include <scsi/scsi_ioctl.h>
+#define	__KERNEL__
+#include <scsi/sg.h>
 
 #include <asm/ia32.h>
 
@@ -60,6 +66,235 @@ put_dirent32 (struct dirent *d, struct linux32_dirent *d32)
 		|| put_user(d->d_reclen, &d32->d_reclen)
 		|| copy_to_user(d32->d_name, d->d_name, namelen + 1));
 }
+/*
+ *  The transform code for the SG_IO ioctl was brazenly lifted from
+ *  the Sparc64 port in the file `arch/sparc64/kernel/ioctl32.c'.
+ *  Thanks to Jakub Jelinek & Eddie C. Dost.
+ */
+typedef struct sg_io_hdr32 {
+	int interface_id;	/* [i] 'S' for SCSI generic (required) */
+	int dxfer_direction;	/* [i] data transfer direction  */
+	char  cmd_len;		/* [i] SCSI command length ( <= 16 bytes) */
+	char  mx_sb_len;		/* [i] max length to write to sbp */
+	short iovec_count;	/* [i] 0 implies no scatter gather */
+	int dxfer_len;		/* [i] byte count of data transfer */
+	int dxferp;		/* [i], [*io] points to data transfer memory
+					      or scatter gather list */
+	int cmdp;		/* [i], [*i] points to command to perform */
+	int sbp;		/* [i], [*o] points to sense_buffer memory */
+	int timeout;		/* [i] MAX_UINT->no timeout (unit: millisec) */
+	int flags;		/* [i] 0 -> default, see SG_FLAG... */
+	int pack_id;		/* [i->o] unused internally (normally) */
+	int usr_ptr;		/* [i->o] unused internally */
+	char  status;		/* [o] scsi status */
+	char  masked_status;	/* [o] shifted, masked scsi status */
+	char  msg_status;	/* [o] messaging level data (optional) */
+	char  sb_len_wr;	/* [o] byte count actually written to sbp */
+	short host_status;	/* [o] errors from host adapter */
+	short driver_status;	/* [o] errors from software driver */
+	int resid;		/* [o] dxfer_len - actual_transferred */
+	int duration;		/* [o] time taken by cmd (unit: millisec) */
+	int info;		/* [o] auxiliary information */
+} sg_io_hdr32_t;  /* 64 bytes long (on IA32) */
+
+struct iovec32 { unsigned int iov_base; int iov_len; };
+
+static int alloc_sg_iovec(sg_io_hdr_t *sgp, int uptr32)
+{
+	struct iovec32 *uiov = (struct iovec32 *) P(uptr32);
+	sg_iovec_t *kiov;
+	int i;
+
+	sgp->dxferp = kmalloc(sgp->iovec_count *
+			      sizeof(sg_iovec_t), GFP_KERNEL);
+	if (!sgp->dxferp)
+		return -ENOMEM;
+	memset(sgp->dxferp, 0,
+	       sgp->iovec_count * sizeof(sg_iovec_t));
+
+	kiov = (sg_iovec_t *) sgp->dxferp;
+	for (i = 0; i < sgp->iovec_count; i++) {
+		int iov_base32;
+		if (__get_user(iov_base32, &uiov->iov_base) ||
+		    __get_user(kiov->iov_len, &uiov->iov_len))
+			return -EFAULT;
+
+		kiov->iov_base = kmalloc(kiov->iov_len, GFP_KERNEL);
+		if (!kiov->iov_base)
+			return -ENOMEM;
+		if (copy_from_user(kiov->iov_base,
+				   (void *) P(iov_base32),
+				   kiov->iov_len))
+			return -EFAULT;
+
+		uiov++;
+		kiov++;
+	}
+
+	return 0;
+}
+
+static int copy_back_sg_iovec(sg_io_hdr_t *sgp, int uptr32)
+{
+	struct iovec32 *uiov = (struct iovec32 *) P(uptr32);
+	sg_iovec_t *kiov = (sg_iovec_t *) sgp->dxferp;
+	int i;
+
+	for (i = 0; i < sgp->iovec_count; i++) {
+		int iov_base32;
+
+		if (__get_user(iov_base32, &uiov->iov_base))
+			return -EFAULT;
+
+		if (copy_to_user((void *) P(iov_base32),
+				 kiov->iov_base,
+				 kiov->iov_len))
+			return -EFAULT;
+
+		uiov++;
+		kiov++;
+	}
+
+	return 0;
+}
+
+static void free_sg_iovec(sg_io_hdr_t *sgp)
+{
+	sg_iovec_t *kiov = (sg_iovec_t *) sgp->dxferp;
+	int i;
+
+	for (i = 0; i < sgp->iovec_count; i++) {
+		if (kiov->iov_base) {
+			kfree(kiov->iov_base);
+			kiov->iov_base = NULL;
+		}
+		kiov++;
+	}
+	kfree(sgp->dxferp);
+	sgp->dxferp = NULL;
+}
+
+static int sg_ioctl_trans(unsigned int fd, unsigned int cmd, unsigned long arg)
+{
+	sg_io_hdr32_t *sg_io32;
+	sg_io_hdr_t sg_io64;
+	int dxferp32, cmdp32, sbp32;
+	mm_segment_t old_fs;
+	int err = 0;
+
+	sg_io32 = (sg_io_hdr32_t *)arg;
+	err = __get_user(sg_io64.interface_id, &sg_io32->interface_id);
+	err |= __get_user(sg_io64.dxfer_direction, &sg_io32->dxfer_direction);
+	err |= __get_user(sg_io64.cmd_len, &sg_io32->cmd_len);
+	err |= __get_user(sg_io64.mx_sb_len, &sg_io32->mx_sb_len);
+	err |= __get_user(sg_io64.iovec_count, &sg_io32->iovec_count);
+	err |= __get_user(sg_io64.dxfer_len, &sg_io32->dxfer_len);
+	err |= __get_user(sg_io64.timeout, &sg_io32->timeout);
+	err |= __get_user(sg_io64.flags, &sg_io32->flags);
+	err |= __get_user(sg_io64.pack_id, &sg_io32->pack_id);
+
+	sg_io64.dxferp = NULL;
+	sg_io64.cmdp = NULL;
+	sg_io64.sbp = NULL;
+
+	err |= __get_user(cmdp32, &sg_io32->cmdp);
+	sg_io64.cmdp = kmalloc(sg_io64.cmd_len, GFP_KERNEL);
+	if (!sg_io64.cmdp) {
+		err = -ENOMEM;
+		goto out;
+	}
+	if (copy_from_user(sg_io64.cmdp,
+			   (void *) P(cmdp32),
+			   sg_io64.cmd_len)) {
+		err = -EFAULT;
+		goto out;
+	}
+
+	err |= __get_user(sbp32, &sg_io32->sbp);
+	sg_io64.sbp = kmalloc(sg_io64.mx_sb_len, GFP_KERNEL);
+	if (!sg_io64.sbp) {
+		err = -ENOMEM;
+		goto out;
+	}
+	if (copy_from_user(sg_io64.sbp,
+			   (void *) P(sbp32),
+			   sg_io64.mx_sb_len)) {
+		err = -EFAULT;
+		goto out;
+	}
+
+	err |= __get_user(dxferp32, &sg_io32->dxferp);
+	if (sg_io64.iovec_count) {
+		int ret;
+
+		if ((ret = alloc_sg_iovec(&sg_io64, dxferp32))) {
+			err = ret;
+			goto out;
+		}
+	} else {
+		sg_io64.dxferp = kmalloc(sg_io64.dxfer_len, GFP_KERNEL);
+		if (!sg_io64.dxferp) {
+			err = -ENOMEM;
+			goto out;
+		}
+		if (copy_from_user(sg_io64.dxferp,
+				   (void *) P(dxferp32),
+				   sg_io64.dxfer_len)) {
+			err = -EFAULT;
+			goto out;
+		}
+	}
+
+	/* Unused internally, do not even bother to copy it over. */
+	sg_io64.usr_ptr = NULL;
+
+	if (err)
+		return -EFAULT;
+
+	old_fs = get_fs();
+	set_fs (KERNEL_DS);
+	err = sys_ioctl (fd, cmd, (unsigned long) &sg_io64);
+	set_fs (old_fs);
+
+	if (err < 0)
+		goto out;
+
+	err = __put_user(sg_io64.pack_id, &sg_io32->pack_id);
+	err |= __put_user(sg_io64.status, &sg_io32->status);
+	err |= __put_user(sg_io64.masked_status, &sg_io32->masked_status);
+	err |= __put_user(sg_io64.msg_status, &sg_io32->msg_status);
+	err |= __put_user(sg_io64.sb_len_wr, &sg_io32->sb_len_wr);
+	err |= __put_user(sg_io64.host_status, &sg_io32->host_status);
+	err |= __put_user(sg_io64.driver_status, &sg_io32->driver_status);
+	err |= __put_user(sg_io64.resid, &sg_io32->resid);
+	err |= __put_user(sg_io64.duration, &sg_io32->duration);
+	err |= __put_user(sg_io64.info, &sg_io32->info);
+	err |= copy_to_user((void *)P(sbp32), sg_io64.sbp, sg_io64.mx_sb_len);
+	if (sg_io64.dxferp) {
+		if (sg_io64.iovec_count)
+			err |= copy_back_sg_iovec(&sg_io64, dxferp32);
+		else
+			err |= copy_to_user((void *)P(dxferp32),
+					    sg_io64.dxferp,
+					    sg_io64.dxfer_len);
+	}
+	if (err)
+		err = -EFAULT;
+
+out:
+	if (sg_io64.cmdp)
+		kfree(sg_io64.cmdp);
+	if (sg_io64.sbp)
+		kfree(sg_io64.sbp);
+	if (sg_io64.dxferp) {
+		if (sg_io64.iovec_count) {
+			free_sg_iovec(&sg_io64);
+		} else {
+			kfree(sg_io64.dxferp);
+		}
+	}
+	return err;
+}
 
 asmlinkage long
 sys32_ioctl (unsigned int fd, unsigned int cmd, unsigned int arg)
@@ -271,6 +506,9 @@ sys32_ioctl (unsigned int fd, unsigned int cmd, unsigned int arg)
 	      default:
 		return sys_ioctl(fd, cmd, (unsigned long)arg);
 
+		case IOCTL_NR(SG_IO):
+			return(sg_ioctl_trans(fd, cmd, arg));
+
 	}
 	printk("%x:unimplemented IA32 ioctl system call\n", cmd);
 	return -EINVAL;

arch/ia64/ia32/sys_ia32.c

@@ -2842,20 +2842,6 @@ putreg (struct task_struct *child, int regno, unsigned int value)
 	}
 }
 
-static inline void
-ia32f2ia64f (void *dst, void *src)
-{
-	asm volatile ("ldfe f6=[%1];; stf.spill [%0]=f6" :: "r"(dst), "r"(src) : "memory");
-	return;
-}
-
-static inline void
-ia64f2ia32f (void *dst, void *src)
-{
-	asm volatile ("ldf.fill f6=[%1];; stfe [%0]=f6" :: "r"(dst),  "r"(src) : "memory");
-	return;
-}
-
 static void
 put_fpreg (int regno, struct _fpreg_ia32 *reg, struct pt_regs *ptp, struct switch_stack *swp,
 	   int tos)

arch/ia64/kernel/fw-emu.c

@@ -2,7 +2,7 @@
  * PAL & SAL emulation.
  *
  * Copyright (C) 1998-2001 Hewlett-Packard Co
- * Copyright (C) 1998-2001 David Mosberger-Tang <davidm@hpl.hp.com>
+ *	David Mosberger-Tang <davidm@hpl.hp.com>
  *
  * For the HP simulator, this file gets include in boot/bootloader.c.
  * For SoftSDV, this file gets included in sys_softsdv.c.

arch/ia64/kernel/iosapic.c

@@ -133,12 +133,8 @@ find_iosapic (unsigned int gsi)
 	return -1;
 }
 
-/*
- * Translate GSI number to the corresponding IA-64 interrupt vector.  If no
- * entry exists, return -1.
- */
-int
-gsi_to_vector (unsigned int gsi)
+static inline int
+_gsi_to_vector (unsigned int gsi)
 {
 	struct iosapic_intr_info *info;
 
@@ -148,6 +144,26 @@ gsi_to_vector (unsigned int gsi)
 	return -1;
 }
 
+/*
+ * Translate GSI number to the corresponding IA-64 interrupt vector.  If no
+ * entry exists, return -1.
+ */
+inline int
+gsi_to_vector (unsigned int gsi)
+{
+	return _gsi_to_vector(gsi);
+}
+
+int
+gsi_to_irq (unsigned int gsi)
+{
+	/*
+	 * XXX fix me: this assumes an identity mapping vetween IA-64 vector and Linux irq
+	 * numbers...
+	 */
+	return _gsi_to_vector(gsi);
+}
+
 static void
 set_rte (unsigned int vector, unsigned int dest)
 {
@@ -157,7 +173,7 @@ set_rte (unsigned int vector, unsigned int dest)
 	int rte_index;
 	char redir;
 
-	DBG(KERN_DEBUG"IOSAPIC: routing vector %d to %x\n", vector, dest);
+	DBG(KERN_DEBUG"IOSAPIC: routing vector %d to 0x%x\n", vector, dest);
 
 	rte_index = iosapic_intr_info[vector].rte_index;
 	if (rte_index < 0)

arch/ia64/kernel/ivt.S

@@ -116,8 +116,8 @@ ENTRY(vhpt_miss)
 	;;
 (p8)	dep r25=r18,r25,2,6
 (p8)	shr r22=r22,HPAGE_SHIFT-PAGE_SHIFT
-	;;
 #endif
+	;;
 	cmp.eq p6,p7=5,r17			// is IFA pointing into to region 5?
 	shr.u r18=r22,PGDIR_SHIFT		// get bits 33-63 of the faulting address
 	;;

arch/ia64/kernel/mca.c

@@ -1012,28 +1012,13 @@ ia64_log_prt_oem_data (int header_len, int sect_len, u8 *p_data, prfunc_t prfunc
 void
 ia64_log_rec_header_print (sal_log_record_header_t *lh, prfunc_t prfunc)
 {
-	char str_buf[32];
-
-	sprintf(str_buf, "%2d.%02d",
-		(lh->revision.major >> 4) * 10 + (lh->revision.major & 0xf),
-		(lh->revision.minor >> 4) * 10 + (lh->revision.minor & 0xf));
-	prfunc("+Err Record ID: %d    SAL Rev: %s\n", lh->id, str_buf);
-	sprintf(str_buf, "%02d/%02d/%04d/ %02d:%02d:%02d",
-		(lh->timestamp.slh_month >> 4) * 10 +
-		(lh->timestamp.slh_month & 0xf),
-		(lh->timestamp.slh_day >> 4) * 10 +
-		(lh->timestamp.slh_day & 0xf),
-		(lh->timestamp.slh_century >> 4) * 1000 +
-		(lh->timestamp.slh_century & 0xf) * 100 +
-		(lh->timestamp.slh_year >> 4) * 10 +
-		(lh->timestamp.slh_year & 0xf),
-		(lh->timestamp.slh_hour >> 4) * 10 +
-		(lh->timestamp.slh_hour & 0xf),
-		(lh->timestamp.slh_minute >> 4) * 10 +
-		(lh->timestamp.slh_minute & 0xf),
-		(lh->timestamp.slh_second >> 4) * 10 +
-		(lh->timestamp.slh_second & 0xf));
-	prfunc("+Time: %s    Severity %d\n", str_buf, lh->severity);
+	prfunc("+Err Record ID: %d    SAL Rev: %2x.%02x\n", lh->id,
+			lh->revision.major, lh->revision.minor);
+	prfunc("+Time: %02x/%02x/%02x%02x %02x:%02x:%02x    Severity %d\n",
+			lh->timestamp.slh_month, lh->timestamp.slh_day,
+			lh->timestamp.slh_century, lh->timestamp.slh_year,
+			lh->timestamp.slh_hour, lh->timestamp.slh_minute,
+			lh->timestamp.slh_second, lh->severity);
 }
 
 /*

arch/ia64/mm/Makefile

@@ -9,5 +9,7 @@
 
 obj-y	 := init.o fault.o tlb.o extable.o
 obj-$(CONFIG_HUGETLB_PAGE) += hugetlbpage.o
+obj-$(CONFIG_NUMA) += numa.o
+obj-$(CONFIG_DISCONTIGMEM) += discontig.o
 
 include $(TOPDIR)/Rules.make