r8152: adjust the flow of power cut for RTL8153B

For runtime resuming, the RTL8153B may be resumed from the state
of power cut, when enabling the feature of UPS. Then, the PHY
would be reset, so it is necessary to be initailized again.

Besides, the USB_U1U2_TIMER also has to be set again, so I move
it from r8153b_init() to r8153b_hw_phy_cfg().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

drivers/net/usb/r8152.c

@@ -1371,6 +1371,10 @@ void write_mii_word(struct net_device *netdev, int phy_id, int reg, int val)
 static int
 r8152_submit_rx(struct r8152 *tp, struct rx_agg *agg, gfp_t mem_flags);
 
+static int
+rtl8152_set_speed(struct r8152 *tp, u8 autoneg, u32 speed, u8 duplex,
+		  u32 advertising);
+
 static int rtl8152_set_mac_address(struct net_device *netdev, void *p)
 {
 	struct r8152 *tp = netdev_priv(netdev);
@@ -3205,8 +3209,6 @@ static void r8153b_ups_en(struct r8152 *tp, bool enable)
 		ocp_data |= BIT(0);
 		ocp_write_byte(tp, MCU_TYPE_USB, 0xcfff, ocp_data);
 	} else {
-		u16 data;
-
 		ocp_data &= ~(UPS_EN | USP_PREWAKE);
 		ocp_write_byte(tp, MCU_TYPE_USB, USB_POWER_CUT, ocp_data);
 
@@ -3214,31 +3216,20 @@ static void r8153b_ups_en(struct r8152 *tp, bool enable)
 		ocp_data &= ~BIT(0);
 		ocp_write_byte(tp, MCU_TYPE_USB, 0xcfff, ocp_data);
 
-		ocp_data = ocp_read_word(tp, MCU_TYPE_USB, USB_MISC_0);
-		ocp_data &= ~PCUT_STATUS;
-		ocp_write_word(tp, MCU_TYPE_USB, USB_MISC_0, ocp_data);
-
-		data = r8153_phy_status(tp, 0);
-
-		switch (data) {
-		case PHY_STAT_PWRDN:
-		case PHY_STAT_EXT_INIT:
-			r8153b_green_en(tp,
-					test_bit(GREEN_ETHERNET, &tp->flags));
+		if (ocp_read_word(tp, MCU_TYPE_USB, USB_MISC_0) & PCUT_STATUS) {
+			int i;
 
-			data = r8152_mdio_read(tp, MII_BMCR);
-			data &= ~BMCR_PDOWN;
-			data |= BMCR_RESET;
-			r8152_mdio_write(tp, MII_BMCR, data);
+			for (i = 0; i < 500; i++) {
+				if (ocp_read_word(tp, MCU_TYPE_PLA, PLA_BOOT_CTRL) &
+				    AUTOLOAD_DONE)
+					break;
+				msleep(20);
+			}
 
-			data = r8153_phy_status(tp, PHY_STAT_LAN_ON);
-			fallthrough;
+			tp->rtl_ops.hw_phy_cfg(tp);
 
-		default:
-			if (data != PHY_STAT_LAN_ON)
-				netif_warn(tp, link, tp->netdev,
-					   "PHY not ready");
-			break;
+			rtl8152_set_speed(tp, tp->autoneg, tp->speed,
+					  tp->duplex, tp->advertising);
 		}
 	}
 }
@@ -4612,13 +4603,37 @@ static void r8153b_hw_phy_cfg(struct r8152 *tp)
 	u32 ocp_data;
 	u16 data;
 
+	ocp_data = ocp_read_word(tp, MCU_TYPE_USB, USB_MISC_0);
+	if (ocp_data & PCUT_STATUS) {
+		ocp_data &= ~PCUT_STATUS;
+		ocp_write_word(tp, MCU_TYPE_USB, USB_MISC_0, ocp_data);
+	}
+
 	/* disable ALDPS before updating the PHY parameters */
 	r8153_aldps_en(tp, false);
 
 	/* disable EEE before updating the PHY parameters */
 	rtl_eee_enable(tp, false);
 
-	rtl8152_apply_firmware(tp, false);
+	/* U1/U2/L1 idle timer. 500 us */
+	ocp_write_word(tp, MCU_TYPE_USB, USB_U1U2_TIMER, 500);
+
+	data = r8153_phy_status(tp, 0);
+
+	switch (data) {
+	case PHY_STAT_PWRDN:
+	case PHY_STAT_EXT_INIT:
+		rtl8152_apply_firmware(tp, true);
+
+		data = r8152_mdio_read(tp, MII_BMCR);
+		data &= ~BMCR_PDOWN;
+		r8152_mdio_write(tp, MII_BMCR, data);
+		break;
+	case PHY_STAT_LAN_ON:
+	default:
+		rtl8152_apply_firmware(tp, false);
+		break;
+	}
 
 	r8153b_green_en(tp, test_bit(GREEN_ETHERNET, &tp->flags));
 
@@ -5544,9 +5559,6 @@ static void r8153b_init(struct r8152 *tp)
 	/* MSC timer = 0xfff * 8ms = 32760 ms */
 	ocp_write_word(tp, MCU_TYPE_USB, USB_MSC_TIMER, 0x0fff);
 
-	/* U1/U2/L1 idle timer. 500 us */
-	ocp_write_word(tp, MCU_TYPE_USB, USB_U1U2_TIMER, 500);
-
 	r8153b_power_cut_en(tp, false);
 	r8153b_ups_en(tp, false);
 	r8153_queue_wake(tp, false);