e1000: fix loss of multicast packets

e1000 (and e1000e, igb, ixgbe, ixgb) all do a series of
operations each time a multicast address is added.  The flow goes
something like

1) stack adds one multicast address
2) stack passes whole current list of unicast and multicast
   addresses to driver
3) driver clears entire list in hardware
4) driver programs each multicast address using iomem in a loop

This was causing multicast packets to be lost during the
reprogramming process.

reference with test program:
http://kerneltrap.org/mailarchive/linux-netdev/2009/3/14/5160514/thread

Thanks to Dave Boutcher for his report and test program.

This driver fix prepares an array all at once in memory and
programs it in one shot to the hardware, not requiring an "erase"
cycle.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/e1000/e1000_main.c

@@ -2335,6 +2335,12 @@ static void e1000_set_rx_mode(struct net_device *netdev)
 	int mta_reg_count = (hw->mac_type == e1000_ich8lan) ?
 				E1000_NUM_MTA_REGISTERS_ICH8LAN :
 				E1000_NUM_MTA_REGISTERS;
+	u32 *mcarray = kcalloc(mta_reg_count, sizeof(u32), GFP_ATOMIC);
+
+	if (!mcarray) {
+		DPRINTK(PROBE, ERR, "memory allocation failed\n");
+		return;
+	}
 
 	if (hw->mac_type == e1000_ich8lan)
 		rar_entries = E1000_RAR_ENTRIES_ICH8LAN;
@@ -2401,22 +2407,34 @@ static void e1000_set_rx_mode(struct net_device *netdev)
 	}
 	WARN_ON(uc_ptr != NULL);
 
-	/* clear the old settings from the multicast hash table */
-
-	for (i = 0; i < mta_reg_count; i++) {
-		E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
-		E1000_WRITE_FLUSH();
-	}
-
 	/* load any remaining addresses into the hash table */
 
 	for (; mc_ptr; mc_ptr = mc_ptr->next) {
+		u32 hash_reg, hash_bit, mta;
 		hash_value = e1000_hash_mc_addr(hw, mc_ptr->da_addr);
-		e1000_mta_set(hw, hash_value);
+		hash_reg = (hash_value >> 5) & 0x7F;
+		hash_bit = hash_value & 0x1F;
+		mta = (1 << hash_bit);
+		mcarray[hash_reg] |= mta;
 	}
 
+	/* write the hash table completely, write from bottom to avoid
+	 * both stupid write combining chipsets, and flushing each write */
+	for (i = mta_reg_count - 1; i >= 0 ; i--) {
+		/*
+		 * If we are on an 82544 has an errata where writing odd
+		 * offsets overwrites the previous even offset, but writing
+		 * backwards over the range solves the issue by always
+		 * writing the odd offset first
+		 */
+		E1000_WRITE_REG_ARRAY(hw, MTA, i, mcarray[i]);
+	}
+	E1000_WRITE_FLUSH();
+
 	if (hw->mac_type == e1000_82542_rev2_0)
 		e1000_leave_82542_rst(adapter);
+
+	kfree(mcarray);
 }
 
 /* Need to wait a few seconds after link up to get diagnostic information from