Commit 831eae69 authored by Stephen Warren's avatar Stephen Warren Committed by Greg Kroah-Hartman

staging: dwc2: set up all module params

The DWC2 USB controller in the BCM2835 (Raspberry Pi) needs some non-
default parameters. Select these based on the compatible value from the
DT node. For all other HW, fall back to the default parameters currently
in use.

The values in params_bcm2835[] were posted to the mailing list by Paul
quite some time ago. I made a couple of minor modifications since then;
to set ahbcfg instead of ahb_single, and to set uframe_sched.
Signed-off-by: default avatarStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent f4b406dc
......@@ -2,7 +2,9 @@ Platform DesignWare HS OTG USB 2.0 controller
-----------------------------------------------------
Required properties:
- compatible : "snps,dwc2"
- compatible : One of:
- brcm,bcm2835-usb: The DWC2 USB controller instance in the BCM2835 SoC.
- snps,dwc2: A generic DWC2 USB controller with default parameters.
- reg : Should contain 1 register range (address and length)
- interrupts : Should contain 1 interrupt
......
......@@ -39,6 +39,7 @@
#include <linux/slab.h>
#include <linux/device.h>
#include <linux/dma-mapping.h>
#include <linux/of_device.h>
#include <linux/platform_device.h>
#include "core.h"
......@@ -46,6 +47,34 @@
static const char dwc2_driver_name[] = "dwc2";
static const struct dwc2_core_params params_bcm2835 = {
.otg_cap = 0, /* HNP/SRP capable */
.otg_ver = 0, /* 1.3 */
.dma_enable = 1,
.dma_desc_enable = 0,
.speed = 0, /* High Speed */
.enable_dynamic_fifo = 1,
.en_multiple_tx_fifo = 1,
.host_rx_fifo_size = 774, /* 774 DWORDs */
.host_nperio_tx_fifo_size = 256, /* 256 DWORDs */
.host_perio_tx_fifo_size = 512, /* 512 DWORDs */
.max_transfer_size = 65535,
.max_packet_count = 511,
.host_channels = 8,
.phy_type = 1, /* UTMI */
.phy_utmi_width = 8, /* 8 bits */
.phy_ulpi_ddr = 0, /* Single */
.phy_ulpi_ext_vbus = 0,
.i2c_enable = 0,
.ulpi_fs_ls = 0,
.host_support_fs_ls_low_power = 0,
.host_ls_low_power_phy_clk = 0, /* 48 MHz */
.ts_dline = 0,
.reload_ctl = 0,
.ahbcfg = 0x10,
.uframe_sched = 1,
};
/**
* dwc2_driver_remove() - Called when the DWC_otg core is unregistered with the
* DWC_otg driver
......@@ -66,6 +95,13 @@ static int dwc2_driver_remove(struct platform_device *dev)
return 0;
}
static const struct of_device_id dwc2_of_match_table[] = {
{ .compatible = "brcm,bcm2835-usb", .data = &params_bcm2835 },
{ .compatible = "snps,dwc2", .data = NULL },
{},
};
MODULE_DEVICE_TABLE(of, dwc2_of_match_table);
/**
* dwc2_driver_probe() - Called when the DWC_otg core is bound to the DWC_otg
* driver
......@@ -80,14 +116,22 @@ static int dwc2_driver_remove(struct platform_device *dev)
*/
static int dwc2_driver_probe(struct platform_device *dev)
{
const struct of_device_id *match;
const struct dwc2_core_params *params;
struct dwc2_core_params defparams;
struct dwc2_hsotg *hsotg;
struct resource *res;
int retval;
int irq;
struct dwc2_core_params params;
/* Default all params to autodetect */
dwc2_set_all_params(&params, -1);
match = of_match_device(dwc2_of_match_table, &dev->dev);
if (match && match->data) {
params = match->data;
} else {
/* Default all params to autodetect */
dwc2_set_all_params(&defparams, -1);
params = &defparams;
}
hsotg = devm_kzalloc(&dev->dev, sizeof(*hsotg), GFP_KERNEL);
if (!hsotg)
......@@ -118,7 +162,7 @@ static int dwc2_driver_probe(struct platform_device *dev)
dev_dbg(&dev->dev, "mapped PA %08lx to VA %p\n",
(unsigned long)res->start, hsotg->regs);
retval = dwc2_hcd_init(hsotg, irq, &params);
retval = dwc2_hcd_init(hsotg, irq, params);
if (retval)
return retval;
......@@ -127,12 +171,6 @@ static int dwc2_driver_probe(struct platform_device *dev)
return retval;
}
static const struct of_device_id dwc2_of_match_table[] = {
{ .compatible = "snps,dwc2" },
{},
};
MODULE_DEVICE_TABLE(of, dwc2_of_match_table);
static struct platform_driver dwc2_platform_driver = {
.driver = {
.name = dwc2_driver_name,
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment