Commit 83342718 authored by Luciano Coelho's avatar Luciano Coelho

wl18xx: add module parameter to force SISO 20MHz

In some cases it may be useful to force narrow-band SISO channels.
Add a new value to the ht_mode module parameter to force the device to
operate in SISO 20MHz.
Signed-off-by: default avatarLuciano Coelho <coelho@ti.com>
Signed-off-by: default avatarArik Nemtsov <arik@wizery.com>
parent 60462b48
......@@ -1055,7 +1055,7 @@ static struct wlcore_ops wl18xx_ops = {
};
/* HT cap appropriate for wide channels */
static struct ieee80211_sta_ht_cap wl18xx_ht_cap = {
static struct ieee80211_sta_ht_cap wl18xx_siso40_ht_cap = {
.cap = IEEE80211_HT_CAP_SGI_20 | IEEE80211_HT_CAP_SGI_40 |
IEEE80211_HT_CAP_SUP_WIDTH_20_40 | IEEE80211_HT_CAP_DSSSCCK40,
.ht_supported = true,
......@@ -1068,6 +1068,19 @@ static struct ieee80211_sta_ht_cap wl18xx_ht_cap = {
},
};
/* HT cap appropriate for SISO 20 */
static struct ieee80211_sta_ht_cap wl18xx_siso20_ht_cap = {
.cap = IEEE80211_HT_CAP_SGI_20,
.ht_supported = true,
.ampdu_factor = IEEE80211_HT_MAX_AMPDU_16K,
.ampdu_density = IEEE80211_HT_MPDU_DENSITY_16,
.mcs = {
.rx_mask = { 0xff, 0, 0, 0, 0, 0, 0, 0, 0, 0, },
.rx_highest = cpu_to_le16(72),
.tx_params = IEEE80211_HT_MCS_TX_DEFINED,
},
};
/* HT cap appropriate for MIMO rates in 20mhz channel */
static struct ieee80211_sta_ht_cap wl18xx_mimo_ht_cap = {
.cap = IEEE80211_HT_CAP_SGI_20,
......@@ -1108,10 +1121,20 @@ int __devinit wl18xx_probe(struct platform_device *pdev)
wl->fw_status_priv_len = sizeof(struct wl18xx_fw_status_priv);
wl->stats.fw_stats_len = sizeof(struct wl18xx_acx_statistics);
wl->static_data_priv_len = sizeof(struct wl18xx_static_data_priv);
memcpy(&wl->ht_cap, &wl18xx_ht_cap, sizeof(wl18xx_ht_cap));
if (!strcmp(ht_mode_param, "mimo"))
if (!strcmp(ht_mode_param, "wide")) {
memcpy(&wl->ht_cap, &wl18xx_siso40_ht_cap,
sizeof(wl18xx_siso40_ht_cap));
} else if (!strcmp(ht_mode_param, "mimo")) {
memcpy(&wl->ht_cap, &wl18xx_mimo_ht_cap,
sizeof(wl18xx_mimo_ht_cap));
} else if (!strcmp(ht_mode_param, "siso20")) {
memcpy(&wl->ht_cap, &wl18xx_siso20_ht_cap,
sizeof(wl18xx_siso20_ht_cap));
} else {
wl1271_error("invalid ht_mode '%s'", ht_mode_param);
goto out_free;
}
wl18xx_conf_init(wl);
......@@ -1131,8 +1154,7 @@ int __devinit wl18xx_probe(struct platform_device *pdev)
priv->conf.phy.low_band_component_type = 0x06;
} else {
wl1271_error("invalid board type '%s'", board_type_param);
wlcore_free_hw(wl);
return -EINVAL;
goto out_free;
}
if (!checksum_param) {
......@@ -1143,6 +1165,10 @@ int __devinit wl18xx_probe(struct platform_device *pdev)
wl->enable_11a = enable_11a_param;
return wlcore_probe(wl, pdev);
out_free:
wlcore_free_hw(wl);
return -EINVAL;
}
static const struct platform_device_id wl18xx_id_table[] __devinitconst = {
......@@ -1174,7 +1200,7 @@ static void __exit wl18xx_exit(void)
module_exit(wl18xx_exit);
module_param_named(ht_mode, ht_mode_param, charp, S_IRUSR);
MODULE_PARM_DESC(ht_mode, "Force HT mode: wide or mimo");
MODULE_PARM_DESC(ht_mode, "Force HT mode: wide (default), mimo or siso20");
module_param_named(board_type, board_type_param, charp, S_IRUSR);
MODULE_PARM_DESC(board_type, "Board type: fpga, hdk (default), evb, com8 or "
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment