remove the mg_disk driver

This drivers was added in 2008, but as far as a I can tell we never had a
single platform that actually registered resources for the platform driver.

It's also been unmaintained for a long time and apparently has a ATA mode
that can be driven using the IDE/libata subsystem.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>

Documentation/blockdev/mflash.txt

-This document describes m[g]flash support in linux.
-
-Contents
-  1. Overview
-  2. Reserved area configuration
-  3. Example of mflash platform driver registration
-
-1. Overview
-
-Mflash and gflash are embedded flash drive. The only difference is mflash is
-MCP(Multi Chip Package) device. These two device operate exactly same way.
-So the rest mflash repersents mflash and gflash altogether.
-
-Internally, mflash has nand flash and other hardware logics and supports
-2 different operation (ATA, IO) modes. ATA mode doesn't need any new
-driver and currently works well under standard IDE subsystem. Actually it's
-one chip SSD. IO mode is ATA-like custom mode for the host that doesn't have
-IDE interface.
-
-Following are brief descriptions about IO mode.
-A. IO mode based on ATA protocol and uses some custom command. (read confirm,
-write confirm)
-B. IO mode uses SRAM bus interface.
-C. IO mode supports 4kB boot area, so host can boot from mflash.
-
-2. Reserved area configuration
-If host boot from mflash, usually needs raw area for boot loader image. All of
-the mflash's block device operation will be taken this value as start offset.
-Note that boot loader's size of reserved area and kernel configuration value
-must be same.
-
-3. Example of mflash platform driver registration
-Working mflash is very straight forward. Adding platform device stuff to board
-configuration file is all. Here is some pseudo example.
-
-static struct mg_drv_data mflash_drv_data = {
-	/* If you want to polling driver set to 1 */
-	.use_polling = 0,
-	/* device attribution */
-	.dev_attr = MG_BOOT_DEV
-};
-
-static struct resource mg_mflash_rsc[] = {
-	/* Base address of mflash */
-	[0] = {
-		.start = 0x08000000,
-		.end = 0x08000000 + SZ_64K - 1,
-		.flags = IORESOURCE_MEM
-	},
-	/* mflash interrupt pin */
-	[1] = {
-		.start = IRQ_GPIO(84),
-		.end = IRQ_GPIO(84),
-		.flags = IORESOURCE_IRQ
-	},
-	/* mflash reset pin */
-	[2] = {
-		.start = 43,
-		.end = 43,
-		.name = MG_RST_PIN,
-		.flags = IORESOURCE_IO
-	},
-	/* mflash reset-out pin
-	 * If you use mflash as storage device (i.e. other than MG_BOOT_DEV),
-	 * should assign this */
-	[3] = {
-		.start = 51,
-		.end = 51,
-		.name = MG_RSTOUT_PIN,
-		.flags = IORESOURCE_IO
-	}
-};
-
-static struct platform_device mflash_dev = {
-	.name = MG_DEV_NAME,
-	.id = -1,
-	.dev = {
-		.platform_data = &mflash_drv_data,
-	},
-	.num_resources = ARRAY_SIZE(mg_mflash_rsc),
-	.resource = mg_mflash_rsc
-};
-
-platform_device_register(&mflash_dev);

drivers/block/Kconfig

@@ -434,23 +434,6 @@ config ATA_OVER_ETH
 	This driver provides Support for ATA over Ethernet block
 	devices like the Coraid EtherDrive (R) Storage Blade.
 
-config MG_DISK
-	tristate "mGine mflash, gflash support"
-	depends on ARM && GPIOLIB
-	help
-	  mGine mFlash(gFlash) block device driver
-
-config MG_DISK_RES
-	int "Size of reserved area before MBR"
-	depends on MG_DISK
-	default 0
-	help
-	  Define size of reserved area that usually used for boot. Unit is KB.
-	  All of the block device operation will be taken this value as start
-	  offset
-	  Examples:
-			1024 => 1 MB
-
 config SUNVDC
 	tristate "Sun Virtual Disk Client support"
 	depends on SUN_LDOMS

drivers/block/Makefile

@@ -19,7 +19,6 @@ obj-$(CONFIG_BLK_CPQ_CISS_DA)  += cciss.o
 obj-$(CONFIG_BLK_DEV_DAC960)	+= DAC960.o
 obj-$(CONFIG_XILINX_SYSACE)	+= xsysace.o
 obj-$(CONFIG_CDROM_PKTCDVD)	+= pktcdvd.o
-obj-$(CONFIG_MG_DISK)		+= mg_disk.o
 obj-$(CONFIG_SUNVDC)		+= sunvdc.o
 obj-$(CONFIG_BLK_DEV_SKD)	+= skd.o
 obj-$(CONFIG_BLK_DEV_OSD)	+= osdblk.o

include/linux/mg_disk.h

-/*
- *  include/linux/mg_disk.c
- *
- *  Private data for mflash platform driver
- *
- * (c) 2008 mGine Co.,LTD
- * (c) 2008 unsik Kim <donari75@gmail.com>
- *
- *  This program is free software; you can redistribute it and/or modify
- *  it under the terms of the GNU General Public License version 2 as
- *  published by the Free Software Foundation.
- */
-
-#ifndef __MG_DISK_H__
-#define __MG_DISK_H__
-
-/* name for platform device */
-#define MG_DEV_NAME "mg_disk"
-
-/* names of GPIO resource */
-#define MG_RST_PIN	"mg_rst"
-/* except MG_BOOT_DEV, reset-out pin should be assigned */
-#define MG_RSTOUT_PIN	"mg_rstout"
-
-/* device attribution */
-/* use mflash as boot device */
-#define MG_BOOT_DEV		(1 << 0)
-/* use mflash as storage device */
-#define MG_STORAGE_DEV		(1 << 1)
-/* same as MG_STORAGE_DEV, but bootloader already done reset sequence */
-#define MG_STORAGE_DEV_SKIP_RST	(1 << 2)
-
-/* private driver data */
-struct mg_drv_data {
-	/* disk resource */
-	u32 use_polling;
-
-	/* device attribution */
-	u32 dev_attr;
-
-	/* internally used */
-	void *host;
-};
-
-#endif