arm64: dts: qcom: msm8998: Fixup uart3 gpio config for bluetooth

It turns out that the wcn3990 can float the gpio lines during bootup, etc
which will result in the uart core thinking there is incoming data.  This
results in the bluetooth stack getting garbage.  By applying a bias to
match what wcn3990 would drive, the issue is corrected.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lore.kernel.org/r/20191021161921.31825-1-jeffrey.l.hugo@gmail.com
[bjorn: Moved board specific pinctrl states to the end]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi

@@ -301,3 +301,26 @@ &wifi {
 	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
 	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
 };
+
+/* PINCTRL - board-specific pinctrl */
+&blsp1_uart3_on {
+	rx {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-up on 45 (RX). This is needed to
+		 * avoid garbage data when the TX pin of the Bluetooth
+		 * module is in tri-state (module powered off or not
+		 * driving the signal yet).
+		 */
+		bias-pull-up;
+	};
+
+	cts {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-down on 47 (CTS) to match the pull
+		 * of the Bluetooth module.
+		 */
+		bias-pull-down;
+	};
+};

arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi

@@ -373,3 +373,26 @@ &wifi {
 	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
 	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
 };
+
+/* PINCTRL - board-specific pinctrl */
+&blsp1_uart3_on {
+	rx {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-up on 45 (RX). This is needed to
+		 * avoid garbage data when the TX pin of the Bluetooth
+		 * module is in tri-state (module powered off or not
+		 * driving the signal yet).
+		 */
+		bias-pull-up;
+	};
+
+	cts {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-down on 47 (CTS) to match the pull
+		 * of the Bluetooth module.
+		 */
+		bias-pull-down;
+	};
+};

arch/arm64/boot/dts/qcom/msm8998-pins.dtsi

@@ -77,13 +77,30 @@ config {
 	};
 
 	blsp1_uart3_on: blsp1_uart3_on {
-		mux {
-			pins = "gpio45", "gpio46", "gpio47", "gpio48";
+		tx {
+			pins = "gpio45";
 			function = "blsp_uart3_a";
+			drive-strength = <2>;
+			bias-disable;
 		};
 
-		config {
-			pins = "gpio45", "gpio46", "gpio47", "gpio48";
+		rx {
+			pins = "gpio46";
+			function = "blsp_uart3_a";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		cts {
+			pins = "gpio47";
+			function = "blsp_uart3_a";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		rfr {
+			pins = "gpio48";
+			function = "blsp_uart3_a";
 			drive-strength = <2>;
 			bias-disable;
 		};