GPIO descriptor cleanup for some Wolfson codecs

Merge series from Linus Walleij <linus.walleij@linaro.org>:

This converts the remaining Wolfson ASoC codecs to
use GPIO descriptors.

These Wolfson codecs are mostly used with different
Samsung S3C (especially Cragganmore 6410) board files,
so the in-tree users are fixed up in the process.

arch/arm/mach-s3c/mach-crag6410-module.c

@@ -32,9 +32,18 @@
 
 #include "crag6410.h"
 
+static struct gpiod_lookup_table wm0010_gpiod_table = {
+	.dev_id = "spi0.0", /* SPI device name */
+	.table = {
+		/* Active high for Glenfarclas Rev 2 */
+		GPIO_LOOKUP("GPION", 6,
+			    "reset", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static struct wm0010_pdata wm0010_pdata = {
-	.gpio_reset = S3C64XX_GPN(6),
-	.reset_active_high = 1, /* Active high for Glenfarclas Rev 2 */
+	/* Intentionally left blank */
 };
 
 static struct spi_board_info wm1253_devs[] = {
@@ -61,10 +70,19 @@ static struct spi_board_info balblair_devs[] = {
 	},
 };
 
+static struct gpiod_lookup_table wm5100_gpiod_table = {
+	.dev_id = "1-001a", /* Device 001a on I2C bus 1 */
+	.table = {
+		GPIO_LOOKUP("GPION", 7,
+			    "wlf,ldo1ena", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("wm5100", 3,
+			    "hp-pol", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static struct wm5100_pdata wm5100_pdata = {
-	.ldo_ena = S3C64XX_GPN(7),
 	.irq_flags = IRQF_TRIGGER_HIGH,
-	.gpio_base = CODEC_GPIO_BASE,
 
 	.in_mode = {
 		WM5100_IN_DIFF,
@@ -73,7 +91,6 @@ static struct wm5100_pdata wm5100_pdata = {
 		WM5100_IN_SE,
 	},
 
-	.hp_pol = CODEC_GPIO_BASE + 3,
 	.jack_modes = {
 		{ WM5100_MICDET_MICBIAS3, 0, 0 },
 		{ WM5100_MICDET_MICBIAS2, 1, 1 },
@@ -110,9 +127,16 @@ static struct wm8996_retune_mobile_config wm8996_retune[] = {
 	},
 };
 
+static struct gpiod_lookup_table wm8996_gpiod_table = {
+	.dev_id = "1-001a", /* Device 001a on I2C bus 1 */
+	.table = {
+		GPIO_LOOKUP("GPION", 7,
+			    "wlf,ldo1ena", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static struct wm8996_pdata wm8996_pdata __initdata = {
-	.ldo_ena = S3C64XX_GPN(7),
-	.gpio_base = CODEC_GPIO_BASE,
 	.micdet_def = 1,
 	.inl_mode = WM8996_DIFFERRENTIAL_1,
 	.inr_mode = WM8996_DIFFERRENTIAL_1,
@@ -296,12 +320,20 @@ static const struct i2c_board_info wm6230_i2c_devs[] = {
 };
 
 static struct wm2200_pdata wm2200_pdata = {
-	.ldo_ena = S3C64XX_GPN(7),
 	.gpio_defaults = {
 		[2] = 0x0005,  /* GPIO3 24.576MHz output clock */
 	},
 };
 
+static struct gpiod_lookup_table wm2200_gpiod_table = {
+	.dev_id = "1-003a", /* Device 003a on I2C bus 1 */
+	.table = {
+		GPIO_LOOKUP("GPION", 7,
+			    "wlf,ldo1ena", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static const struct i2c_board_info wm2200_i2c[] = {
 	{ I2C_BOARD_INFO("wm2200", 0x3a),
 	  .platform_data = &wm2200_pdata, },
@@ -337,18 +369,21 @@ static const struct {
 	{ .id = 0x21, .rev = 0xff, .name = "1275-EV1 Mortlach" },
 	{ .id = 0x25, .rev = 0xff, .name = "1274-EV1 Glencadam" },
 	{ .id = 0x31, .rev = 0xff, .name = "1253-EV1 Tomatin",
-	  .spi_devs = wm1253_devs, .num_spi_devs = ARRAY_SIZE(wm1253_devs) },
+	  .spi_devs = wm1253_devs, .num_spi_devs = ARRAY_SIZE(wm1253_devs),
+	  .gpiod_table = &wm0010_gpiod_table },
 	{ .id = 0x32, .rev = 0xff, .name = "XXXX-EV1 Caol Illa" },
 	{ .id = 0x33, .rev = 0xff, .name = "XXXX-EV1 Oban" },
 	{ .id = 0x34, .rev = 0xff, .name = "WM0010-6320-CS42 Balblair",
 	  .spi_devs = balblair_devs,
 	  .num_spi_devs = ARRAY_SIZE(balblair_devs) },
 	{ .id = 0x39, .rev = 0xff, .name = "1254-EV1 Dallas Dhu",
-	  .i2c_devs = wm1254_devs, .num_i2c_devs = ARRAY_SIZE(wm1254_devs) },
+	  .i2c_devs = wm1254_devs, .num_i2c_devs = ARRAY_SIZE(wm1254_devs),
+	  .gpiod_table = &wm8996_gpiod_table },
 	{ .id = 0x3a, .rev = 0xff, .name = "1259-EV1 Tobermory",
 	  .i2c_devs = wm1259_devs, .num_i2c_devs = ARRAY_SIZE(wm1259_devs) },
 	{ .id = 0x3b, .rev = 0xff, .name = "1255-EV1 Kilchoman",
-	  .i2c_devs = wm1255_devs, .num_i2c_devs = ARRAY_SIZE(wm1255_devs) },
+	  .i2c_devs = wm1255_devs, .num_i2c_devs = ARRAY_SIZE(wm1255_devs),
+	  .gpiod_table = &wm5100_gpiod_table },
 	{ .id = 0x3c, .rev = 0xff, .name = "1273-EV1 Longmorn" },
 	{ .id = 0x3d, .rev = 0xff, .name = "1277-EV1 Littlemill",
 	  .i2c_devs = wm1277_devs, .num_i2c_devs = ARRAY_SIZE(wm1277_devs),
@@ -362,7 +397,8 @@ static const struct {
 	  .num_spi_devs = ARRAY_SIZE(wm5102_spi_devs),
 	  .gpiod_table = &wm5102_gpiod_table },
 	{ .id = 0x3f, .rev = -1, .name = "WM2200-6271-CS90-M-REV1",
-	  .i2c_devs = wm2200_i2c, .num_i2c_devs = ARRAY_SIZE(wm2200_i2c) },
+	  .i2c_devs = wm2200_i2c, .num_i2c_devs = ARRAY_SIZE(wm2200_i2c),
+	  .gpiod_table = &wm2200_gpiod_table },
 };
 
 static int wlf_gf_module_probe(struct i2c_client *i2c)

arch/arm/mach-s3c/mach-crag6410.c

@@ -39,8 +39,6 @@
 #include <linux/mfd/wm831x/irq.h>
 #include <linux/mfd/wm831x/gpio.h>
 
-#include <sound/wm1250-ev1.h>
-
 #include <asm/mach/arch.h>
 #include <asm/mach-types.h>
 
@@ -713,13 +711,16 @@ static struct wm831x_pdata glenfarclas_pmic_pdata = {
 	.disable_touch = true,
 };
 
-static struct wm1250_ev1_pdata wm1250_ev1_pdata = {
-	.gpios = {
-		[WM1250_EV1_GPIO_CLK_ENA] = S3C64XX_GPN(12),
-		[WM1250_EV1_GPIO_CLK_SEL0] = S3C64XX_GPL(12),
-		[WM1250_EV1_GPIO_CLK_SEL1] = S3C64XX_GPL(13),
-		[WM1250_EV1_GPIO_OSR] = S3C64XX_GPL(14),
-		[WM1250_EV1_GPIO_MASTER] = S3C64XX_GPL(8),
+static struct gpiod_lookup_table crag_wm1250_ev1_gpiod_table = {
+	/* The WM1250-EV1 is device 0027 on I2C bus 1 */
+	.dev_id = "1-0027",
+	.table = {
+		GPIO_LOOKUP("GPION", 12, "clk-ena", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("GPIOL", 12, "clk-sel0", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("GPIOL", 13, "clk-sel1", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("GPIOL", 14, "osr", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("GPIOL", 8, "master", GPIO_ACTIVE_HIGH),
+		{ },
 	},
 };
 
@@ -733,9 +734,7 @@ static struct i2c_board_info i2c_devs1[] = {
 	{ I2C_BOARD_INFO("wlf-gf-module", 0x24) },
 	{ I2C_BOARD_INFO("wlf-gf-module", 0x25) },
 	{ I2C_BOARD_INFO("wlf-gf-module", 0x26) },
-
-	{ I2C_BOARD_INFO("wm1250-ev1", 0x27),
-	  .platform_data = &wm1250_ev1_pdata },
+	{ I2C_BOARD_INFO("wm1250-ev1", 0x27), },
 };
 
 static struct s3c2410_platform_i2c i2c1_pdata = {
@@ -862,6 +861,7 @@ static void __init crag6410_machine_init(void)
 
 	gpiod_add_lookup_table(&crag_pmic_gpiod_table);
 	i2c_register_board_info(0, i2c_devs0, ARRAY_SIZE(i2c_devs0));
+	gpiod_add_lookup_table(&crag_wm1250_ev1_gpiod_table);
 	i2c_register_board_info(1, i2c_devs1, ARRAY_SIZE(i2c_devs1));
 
 	samsung_keypad_set_platdata(&crag6410_keypad_data);

include/sound/wm0010.h

@@ -11,12 +11,6 @@
 #define WM0010_PDATA_H
 
 struct wm0010_pdata {
-	int gpio_reset;
-
-	/* Set if there is an inverter between the GPIO controlling
-	 * the reset signal and the device.
-	 */
-	int reset_active_high;
 	int irq_flags;
 };
 

include/sound/wm1250-ev1.h

-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * linux/sound/wm1250-ev1.h - Platform data for WM1250-EV1
- *
- * Copyright 2011 Wolfson Microelectronics. PLC.
- */
-
-#ifndef __LINUX_SND_WM1250_EV1_H
-#define __LINUX_SND_WM1250_EV1_H
-
-#define WM1250_EV1_NUM_GPIOS 5
-
-#define WM1250_EV1_GPIO_CLK_ENA  0
-#define WM1250_EV1_GPIO_CLK_SEL0 1
-#define WM1250_EV1_GPIO_CLK_SEL1 2
-#define WM1250_EV1_GPIO_OSR      3
-#define WM1250_EV1_GPIO_MASTER   4
-
-
-struct wm1250_ev1_pdata {
-	int gpios[WM1250_EV1_NUM_GPIOS];
-};
-
-#endif

include/sound/wm2200.h

@@ -42,8 +42,6 @@ struct wm2200_micbias {
 };
 
 struct wm2200_pdata {
-	int reset;      /** GPIO controlling /RESET, if any */
-	int ldo_ena;    /** GPIO controlling LODENA, if any */
 	int irq_flags;
 
 	int gpio_defaults[4];

include/sound/wm5100.h

@@ -36,11 +36,7 @@ struct wm5100_jack_mode {
 #define WM5100_GPIO_SET 0x10000
 
 struct wm5100_pdata {
-	int reset;      /** GPIO controlling /RESET, if any */
-	int ldo_ena;    /** GPIO controlling LODENA, if any */
-	int hp_pol;     /** GPIO controlling headset polarity, if any */
 	int irq_flags;
-	int gpio_base;
 
 	struct wm5100_jack_mode jack_modes[2];
 

include/sound/wm8996.h

@@ -33,8 +33,6 @@ struct wm8996_retune_mobile_config {
 struct wm8996_pdata {
 	int irq_flags;  /** Set IRQ trigger flags; default active low */
 
-	int ldo_ena;  /** GPIO for LDO1; -1 for none */
-
 	int micdet_def;  /** Default MICDET_SRC/HP1FB_SRC/MICD_BIAS */
 
 	enum wm8996_inmode inl_mode;
@@ -42,7 +40,6 @@ struct wm8996_pdata {
 
 	u32 spkmute_seq;  /** Value for register 0x802 */
 
-	int gpio_base;
 	u32 gpio_default[5];
 
 	int num_retune_mobile_cfgs;

sound/soc/codecs/wm0010.c

@@ -18,7 +18,7 @@
 #include <linux/firmware.h>
 #include <linux/delay.h>
 #include <linux/fs.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/regulator/consumer.h>
 #include <linux/mutex.h>
 #include <linux/workqueue.h>
@@ -94,8 +94,7 @@ struct wm0010_priv {
 
 	struct wm0010_pdata pdata;
 
-	int gpio_reset;
-	int gpio_reset_value;
+	struct gpio_desc *reset;
 
 	struct regulator_bulk_data core_supplies[2];
 	struct regulator *dbvdd;
@@ -174,8 +173,7 @@ static void wm0010_halt(struct snd_soc_component *component)
 	case WM0010_STAGE2:
 	case WM0010_FIRMWARE:
 		/* Remember to put chip back into reset */
-		gpio_set_value_cansleep(wm0010->gpio_reset,
-					wm0010->gpio_reset_value);
+		gpiod_set_value_cansleep(wm0010->reset, 1);
 		/* Disable the regulators */
 		regulator_disable(wm0010->dbvdd);
 		regulator_bulk_disable(ARRAY_SIZE(wm0010->core_supplies),
@@ -610,7 +608,7 @@ static int wm0010_boot(struct snd_soc_component *component)
 	}
 
 	/* Release reset */
-	gpio_set_value_cansleep(wm0010->gpio_reset, !wm0010->gpio_reset_value);
+	gpiod_set_value_cansleep(wm0010->reset, 0);
 	spin_lock_irqsave(&wm0010->irq_lock, flags);
 	wm0010->state = WM0010_OUT_OF_RESET;
 	spin_unlock_irqrestore(&wm0010->irq_lock, flags);
@@ -863,7 +861,6 @@ static int wm0010_probe(struct snd_soc_component *component)
 
 static int wm0010_spi_probe(struct spi_device *spi)
 {
-	unsigned long gpio_flags;
 	int ret;
 	int trigger;
 	int irq;
@@ -903,31 +900,11 @@ static int wm0010_spi_probe(struct spi_device *spi)
 		return ret;
 	}
 
-	if (wm0010->pdata.gpio_reset) {
-		wm0010->gpio_reset = wm0010->pdata.gpio_reset;
-
-		if (wm0010->pdata.reset_active_high)
-			wm0010->gpio_reset_value = 1;
-		else
-			wm0010->gpio_reset_value = 0;
-
-		if (wm0010->gpio_reset_value)
-			gpio_flags = GPIOF_OUT_INIT_HIGH;
-		else
-			gpio_flags = GPIOF_OUT_INIT_LOW;
-
-		ret = devm_gpio_request_one(wm0010->dev, wm0010->gpio_reset,
-					    gpio_flags, "wm0010 reset");
-		if (ret < 0) {
-			dev_err(wm0010->dev,
-				"Failed to request GPIO for DSP reset: %d\n",
-				ret);
-			return ret;
-		}
-	} else {
-		dev_err(wm0010->dev, "No reset GPIO configured\n");
-		return -EINVAL;
-	}
+	wm0010->reset = devm_gpiod_get(wm0010->dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(wm0010->reset))
+		return dev_err_probe(wm0010->dev, PTR_ERR(wm0010->reset),
+				     "could not get RESET GPIO\n");
+	gpiod_set_consumer_name(wm0010->reset, "wm0010 reset");
 
 	wm0010->state = WM0010_POWER_OFF;
 
@@ -972,8 +949,7 @@ static void wm0010_spi_remove(struct spi_device *spi)
 {
 	struct wm0010_priv *wm0010 = spi_get_drvdata(spi);
 
-	gpio_set_value_cansleep(wm0010->gpio_reset,
-				wm0010->gpio_reset_value);
+	gpiod_set_value_cansleep(wm0010->reset, 1);
 
 	irq_set_irq_wake(wm0010->irq, 0);
 

sound/soc/codecs/wm1250-ev1.c

@@ -9,34 +9,23 @@
 #include <linux/module.h>
 #include <linux/slab.h>
 #include <linux/i2c.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 
 #include <sound/soc.h>
 #include <sound/soc-dapm.h>
-#include <sound/wm1250-ev1.h>
-
-static const char *wm1250_gpio_names[WM1250_EV1_NUM_GPIOS] = {
-	"WM1250 CLK_ENA",
-	"WM1250 CLK_SEL0",
-	"WM1250 CLK_SEL1",
-	"WM1250 OSR",
-	"WM1250 MASTER",
-};
 
 struct wm1250_priv {
-	struct gpio gpios[WM1250_EV1_NUM_GPIOS];
+	struct gpio_desc *clk_ena;
+	struct gpio_desc *clk_sel0;
+	struct gpio_desc *clk_sel1;
+	struct gpio_desc *osr;
+	struct gpio_desc *master;
 };
 
 static int wm1250_ev1_set_bias_level(struct snd_soc_component *component,
 				     enum snd_soc_bias_level level)
 {
 	struct wm1250_priv *wm1250 = dev_get_drvdata(component->dev);
-	int ena;
-
-	if (wm1250)
-		ena = wm1250->gpios[WM1250_EV1_GPIO_CLK_ENA].gpio;
-	else
-		ena = -1;
 
 	switch (level) {
 	case SND_SOC_BIAS_ON:
@@ -46,13 +35,11 @@ static int wm1250_ev1_set_bias_level(struct snd_soc_component *component,
 		break;
 
 	case SND_SOC_BIAS_STANDBY:
-		if (ena >= 0)
-			gpio_set_value_cansleep(ena, 1);
+		gpiod_set_value_cansleep(wm1250->clk_ena, 1);
 		break;
 
 	case SND_SOC_BIAS_OFF:
-		if (ena >= 0)
-			gpio_set_value_cansleep(ena, 0);
+		gpiod_set_value_cansleep(wm1250->clk_ena, 0);
 		break;
 	}
 
@@ -80,28 +67,20 @@ static int wm1250_ev1_hw_params(struct snd_pcm_substream *substream,
 
 	switch (params_rate(params)) {
 	case 8000:
-		gpio_set_value(wm1250->gpios[WM1250_EV1_GPIO_CLK_SEL0].gpio,
-			       1);
-		gpio_set_value(wm1250->gpios[WM1250_EV1_GPIO_CLK_SEL1].gpio,
-			       1);
+		gpiod_set_value(wm1250->clk_sel0, 1);
+		gpiod_set_value(wm1250->clk_sel1, 1);
 		break;
 	case 16000:
-		gpio_set_value(wm1250->gpios[WM1250_EV1_GPIO_CLK_SEL0].gpio,
-			       0);
-		gpio_set_value(wm1250->gpios[WM1250_EV1_GPIO_CLK_SEL1].gpio,
-			       1);
+		gpiod_set_value(wm1250->clk_sel0, 0);
+		gpiod_set_value(wm1250->clk_sel1, 1);
 		break;
 	case 32000:
-		gpio_set_value(wm1250->gpios[WM1250_EV1_GPIO_CLK_SEL0].gpio,
-			       1);
-		gpio_set_value(wm1250->gpios[WM1250_EV1_GPIO_CLK_SEL1].gpio,
-			       0);
+		gpiod_set_value(wm1250->clk_sel0, 1);
+		gpiod_set_value(wm1250->clk_sel1, 0);
 		break;
 	case 64000:
-		gpio_set_value(wm1250->gpios[WM1250_EV1_GPIO_CLK_SEL0].gpio,
-			       0);
-		gpio_set_value(wm1250->gpios[WM1250_EV1_GPIO_CLK_SEL1].gpio,
-			       0);
+		gpiod_set_value(wm1250->clk_sel0, 0);
+		gpiod_set_value(wm1250->clk_sel1, 0);
 		break;
 	default:
 		return -EINVAL;
@@ -150,45 +129,43 @@ static int wm1250_ev1_pdata(struct i2c_client *i2c)
 {
 	struct wm1250_ev1_pdata *pdata = dev_get_platdata(&i2c->dev);
 	struct wm1250_priv *wm1250;
-	int i, ret;
+	int ret;
 
 	if (!pdata)
 		return 0;
 
 	wm1250 = devm_kzalloc(&i2c->dev, sizeof(*wm1250), GFP_KERNEL);
-	if (!wm1250) {
-		ret = -ENOMEM;
-		goto err;
-	}
-
-	for (i = 0; i < ARRAY_SIZE(wm1250->gpios); i++) {
-		wm1250->gpios[i].gpio = pdata->gpios[i];
-		wm1250->gpios[i].label = wm1250_gpio_names[i];
-		wm1250->gpios[i].flags = GPIOF_OUT_INIT_LOW;
-	}
-	wm1250->gpios[WM1250_EV1_GPIO_CLK_SEL0].flags = GPIOF_OUT_INIT_HIGH;
-	wm1250->gpios[WM1250_EV1_GPIO_CLK_SEL1].flags = GPIOF_OUT_INIT_HIGH;
-
-	ret = gpio_request_array(wm1250->gpios, ARRAY_SIZE(wm1250->gpios));
-	if (ret != 0) {
-		dev_err(&i2c->dev, "Failed to get GPIOs: %d\n", ret);
-		goto err;
-	}
+	if (!wm1250)
+		return -ENOMEM;
+
+	wm1250->clk_ena = devm_gpiod_get(&i2c->dev, "clk-ena", GPIOD_OUT_LOW);
+	if (IS_ERR(wm1250->clk_ena))
+		return dev_err_probe(&i2c->dev, PTR_ERR(wm1250->clk_ena),
+				     "failed to get clock enable GPIO\n");
+
+	wm1250->clk_sel0 = devm_gpiod_get(&i2c->dev, "clk-sel0", GPIOD_OUT_HIGH);
+	if (IS_ERR(wm1250->clk_sel0))
+		return dev_err_probe(&i2c->dev, PTR_ERR(wm1250->clk_sel0),
+				     "failed to get clock sel0 GPIO\n");
+
+	wm1250->clk_sel1 = devm_gpiod_get(&i2c->dev, "clk-sel1", GPIOD_OUT_HIGH);
+	if (IS_ERR(wm1250->clk_sel1))
+		return dev_err_probe(&i2c->dev, PTR_ERR(wm1250->clk_sel1),
+				     "failed to get clock sel1 GPIO\n");
+
+	wm1250->osr = devm_gpiod_get(&i2c->dev, "osr", GPIOD_OUT_LOW);
+	if (IS_ERR(wm1250->osr))
+		return dev_err_probe(&i2c->dev, PTR_ERR(wm1250->osr),
+				     "failed to get OSR GPIO\n");
+
+	wm1250->master = devm_gpiod_get(&i2c->dev, "master", GPIOD_OUT_LOW);
+	if (IS_ERR(wm1250->master))
+		return dev_err_probe(&i2c->dev, PTR_ERR(wm1250->master),
+				     "failed to get MASTER GPIO\n");
 
 	dev_set_drvdata(&i2c->dev, wm1250);
 
 	return ret;
-
-err:
-	return ret;
-}
-
-static void wm1250_ev1_free(struct i2c_client *i2c)
-{
-	struct wm1250_priv *wm1250 = dev_get_drvdata(&i2c->dev);
-
-	if (wm1250)
-		gpio_free_array(wm1250->gpios, ARRAY_SIZE(wm1250->gpios));
 }
 
 static int wm1250_ev1_probe(struct i2c_client *i2c)
@@ -221,18 +198,12 @@ static int wm1250_ev1_probe(struct i2c_client *i2c)
 				     &wm1250_ev1_dai, 1);
 	if (ret != 0) {
 		dev_err(&i2c->dev, "Failed to register CODEC: %d\n", ret);
-		wm1250_ev1_free(i2c);
 		return ret;
 	}
 
 	return 0;
 }
 
-static void wm1250_ev1_remove(struct i2c_client *i2c)
-{
-	wm1250_ev1_free(i2c);
-}
-
 static const struct i2c_device_id wm1250_ev1_i2c_id[] = {
 	{ "wm1250-ev1", 0 },
 	{ }
@@ -244,7 +215,6 @@ static struct i2c_driver wm1250_ev1_i2c_driver = {
 		.name = "wm1250-ev1",
 	},
 	.probe =    wm1250_ev1_probe,
-	.remove =   wm1250_ev1_remove,
 	.id_table = wm1250_ev1_i2c_id,
 };
 

sound/soc/codecs/wm2200.c

@@ -14,7 +14,7 @@
 #include <linux/pm.h>
 #include <linux/firmware.h>
 #include <linux/gcd.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/i2c.h>
 #include <linux/pm_runtime.h>
 #include <linux/regulator/consumer.h>
@@ -79,6 +79,8 @@ struct wm2200_priv {
 	struct snd_soc_component *component;
 	struct wm2200_pdata pdata;
 	struct regulator_bulk_data core_supplies[WM2200_NUM_CORE_SUPPLIES];
+	struct gpio_desc *ldo_ena;
+	struct gpio_desc *reset;
 
 	struct completion fll_lock;
 	int fll_fout;
@@ -975,9 +977,10 @@ static const struct reg_sequence wm2200_reva_patch[] = {
 
 static int wm2200_reset(struct wm2200_priv *wm2200)
 {
-	if (wm2200->pdata.reset) {
-		gpio_set_value_cansleep(wm2200->pdata.reset, 0);
-		gpio_set_value_cansleep(wm2200->pdata.reset, 1);
+	if (wm2200->reset) {
+		/* Descriptor flagged active low, so this will be inverted */
+		gpiod_set_value_cansleep(wm2200->reset, 1);
+		gpiod_set_value_cansleep(wm2200->reset, 0);
 
 		return 0;
 	} else {
@@ -2246,28 +2249,28 @@ static int wm2200_i2c_probe(struct i2c_client *i2c)
 		return ret;
 	}
 
-	if (wm2200->pdata.ldo_ena) {
-		ret = devm_gpio_request_one(&i2c->dev, wm2200->pdata.ldo_ena,
-					    GPIOF_OUT_INIT_HIGH,
-					    "WM2200 LDOENA");
-		if (ret < 0) {
-			dev_err(&i2c->dev, "Failed to request LDOENA %d: %d\n",
-				wm2200->pdata.ldo_ena, ret);
-			goto err_enable;
-		}
+	wm2200->ldo_ena = devm_gpiod_get_optional(&i2c->dev, "wlf,ldo1ena",
+						  GPIOD_OUT_HIGH);
+	if (IS_ERR(wm2200->ldo_ena)) {
+		ret = PTR_ERR(wm2200->ldo_ena);
+		dev_err(&i2c->dev, "Failed to request LDOENA GPIO %d\n",
+			ret);
+		goto err_enable;
+	}
+	if (wm2200->ldo_ena) {
+		gpiod_set_consumer_name(wm2200->ldo_ena, "WM2200 LDOENA");
 		msleep(2);
 	}
 
-	if (wm2200->pdata.reset) {
-		ret = devm_gpio_request_one(&i2c->dev, wm2200->pdata.reset,
-					    GPIOF_OUT_INIT_HIGH,
-					    "WM2200 /RESET");
-		if (ret < 0) {
-			dev_err(&i2c->dev, "Failed to request /RESET %d: %d\n",
-				wm2200->pdata.reset, ret);
-			goto err_ldo;
-		}
+	wm2200->reset = devm_gpiod_get_optional(&i2c->dev, "reset",
+						GPIOD_OUT_LOW);
+	if (IS_ERR(wm2200->reset)) {
+		ret = PTR_ERR(wm2200->reset);
+		dev_err(&i2c->dev, "Failed to request RESET GPIO %d\n",
+			ret);
+		goto err_ldo;
 	}
+	gpiod_set_consumer_name(wm2200->reset, "WM2200 /RESET");
 
 	ret = regmap_read(wm2200->regmap, WM2200_SOFTWARE_RESET, &reg);
 	if (ret < 0) {
@@ -2403,11 +2406,9 @@ static int wm2200_i2c_probe(struct i2c_client *i2c)
 	if (i2c->irq)
 		free_irq(i2c->irq, wm2200);
 err_reset:
-	if (wm2200->pdata.reset)
-		gpio_set_value_cansleep(wm2200->pdata.reset, 0);
+	gpiod_set_value_cansleep(wm2200->reset, 1);
 err_ldo:
-	if (wm2200->pdata.ldo_ena)
-		gpio_set_value_cansleep(wm2200->pdata.ldo_ena, 0);
+	gpiod_set_value_cansleep(wm2200->ldo_ena, 0);
 err_enable:
 	regulator_bulk_disable(ARRAY_SIZE(wm2200->core_supplies),
 			       wm2200->core_supplies);
@@ -2421,10 +2422,9 @@ static void wm2200_i2c_remove(struct i2c_client *i2c)
 	pm_runtime_disable(&i2c->dev);
 	if (i2c->irq)
 		free_irq(i2c->irq, wm2200);
-	if (wm2200->pdata.reset)
-		gpio_set_value_cansleep(wm2200->pdata.reset, 0);
-	if (wm2200->pdata.ldo_ena)
-		gpio_set_value_cansleep(wm2200->pdata.ldo_ena, 0);
+	/* Assert RESET, disable LDO */
+	gpiod_set_value_cansleep(wm2200->reset, 1);
+	gpiod_set_value_cansleep(wm2200->ldo_ena, 0);
 	regulator_bulk_disable(ARRAY_SIZE(wm2200->core_supplies),
 			       wm2200->core_supplies);
 }
@@ -2436,8 +2436,7 @@ static int wm2200_runtime_suspend(struct device *dev)
 
 	regcache_cache_only(wm2200->regmap, true);
 	regcache_mark_dirty(wm2200->regmap);
-	if (wm2200->pdata.ldo_ena)
-		gpio_set_value_cansleep(wm2200->pdata.ldo_ena, 0);
+	gpiod_set_value_cansleep(wm2200->ldo_ena, 0);
 	regulator_bulk_disable(ARRAY_SIZE(wm2200->core_supplies),
 			       wm2200->core_supplies);
 
@@ -2457,8 +2456,8 @@ static int wm2200_runtime_resume(struct device *dev)
 		return ret;
 	}
 
-	if (wm2200->pdata.ldo_ena) {
-		gpio_set_value_cansleep(wm2200->pdata.ldo_ena, 1);
+	if (wm2200->ldo_ena) {
+		gpiod_set_value_cansleep(wm2200->ldo_ena, 1);
 		msleep(2);
 	}
 

sound/soc/codecs/wm5100.c

@@ -15,7 +15,7 @@
 #include <linux/pm.h>
 #include <linux/gcd.h>
 #include <linux/gpio/driver.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/i2c.h>
 #include <linux/pm_runtime.h>
 #include <linux/regulator/consumer.h>
@@ -55,6 +55,9 @@ struct wm5100_priv {
 	struct snd_soc_component *component;
 
 	struct regulator_bulk_data core_supplies[WM5100_NUM_CORE_SUPPLIES];
+	struct gpio_desc *reset;
+	struct gpio_desc *ldo_ena;
+	struct gpio_desc *hp_pol;
 
 	int rev;
 
@@ -205,9 +208,9 @@ static void wm5100_free_sr(struct snd_soc_component *component, int rate)
 
 static int wm5100_reset(struct wm5100_priv *wm5100)
 {
-	if (wm5100->pdata.reset) {
-		gpio_set_value_cansleep(wm5100->pdata.reset, 0);
-		gpio_set_value_cansleep(wm5100->pdata.reset, 1);
+	if (wm5100->reset) {
+		gpiod_set_value_cansleep(wm5100->reset, 1);
+		gpiod_set_value_cansleep(wm5100->reset, 0);
 
 		return 0;
 	} else {
@@ -1974,7 +1977,7 @@ static void wm5100_set_detect_mode(struct wm5100_priv *wm5100, int the_mode)
 	if (WARN_ON(the_mode >= ARRAY_SIZE(wm5100->pdata.jack_modes)))
 		return;
 
-	gpio_set_value_cansleep(wm5100->pdata.hp_pol, mode->hp_pol);
+	gpiod_set_value_cansleep(wm5100->hp_pol, mode->hp_pol);
 	regmap_update_bits(wm5100->regmap, WM5100_ACCESSORY_DETECT_MODE_1,
 			   WM5100_ACCDET_BIAS_SRC_MASK |
 			   WM5100_ACCDET_SRC,
@@ -2299,11 +2302,7 @@ static void wm5100_init_gpio(struct i2c_client *i2c)
 	wm5100->gpio_chip = wm5100_template_chip;
 	wm5100->gpio_chip.ngpio = 6;
 	wm5100->gpio_chip.parent = &i2c->dev;
-
-	if (wm5100->pdata.gpio_base)
-		wm5100->gpio_chip.base = wm5100->pdata.gpio_base;
-	else
-		wm5100->gpio_chip.base = -1;
+	wm5100->gpio_chip.base = -1;
 
 	ret = gpiochip_add_data(&wm5100->gpio_chip, wm5100);
 	if (ret != 0)
@@ -2349,35 +2348,20 @@ static int wm5100_probe(struct snd_soc_component *component)
 		snd_soc_dapm_new_controls(dapm, wm5100_dapm_widgets_noirq,
 					  ARRAY_SIZE(wm5100_dapm_widgets_noirq));
 
-	if (wm5100->pdata.hp_pol) {
-		ret = gpio_request_one(wm5100->pdata.hp_pol,
-				       GPIOF_OUT_INIT_HIGH, "WM5100 HP_POL");
-		if (ret < 0) {
-			dev_err(&i2c->dev, "Failed to request HP_POL %d: %d\n",
-				wm5100->pdata.hp_pol, ret);
-			goto err_gpio;
-		}
+	wm5100->hp_pol = devm_gpiod_get_optional(&i2c->dev, "hp-pol",
+						 GPIOD_OUT_HIGH);
+	if (IS_ERR(wm5100->hp_pol)) {
+		ret = PTR_ERR(wm5100->hp_pol);
+		dev_err(&i2c->dev, "Failed to request HP_POL GPIO: %d\n",
+			ret);
+		return ret;
 	}
 
 	return 0;
-
-err_gpio:
-
-	return ret;
-}
-
-static void wm5100_remove(struct snd_soc_component *component)
-{
-	struct wm5100_priv *wm5100 = snd_soc_component_get_drvdata(component);
-
-	if (wm5100->pdata.hp_pol) {
-		gpio_free(wm5100->pdata.hp_pol);
-	}
 }
 
 static const struct snd_soc_component_driver soc_component_dev_wm5100 = {
 	.probe			= wm5100_probe,
-	.remove			= wm5100_remove,
 	.set_sysclk		= wm5100_set_sysclk,
 	.set_pll		= wm5100_set_fll,
 	.seq_notifier		= wm5100_seq_notifier,
@@ -2460,26 +2444,26 @@ static int wm5100_i2c_probe(struct i2c_client *i2c)
 		goto err;
 	}
 
-	if (wm5100->pdata.ldo_ena) {
-		ret = gpio_request_one(wm5100->pdata.ldo_ena,
-				       GPIOF_OUT_INIT_HIGH, "WM5100 LDOENA");
-		if (ret < 0) {
-			dev_err(&i2c->dev, "Failed to request LDOENA %d: %d\n",
-				wm5100->pdata.ldo_ena, ret);
-			goto err_enable;
-		}
+	wm5100->ldo_ena = devm_gpiod_get_optional(&i2c->dev, "wlf,ldo1ena",
+						  GPIOD_OUT_HIGH);
+	if (IS_ERR(wm5100->ldo_ena)) {
+		ret = PTR_ERR(wm5100->ldo_ena);
+		dev_err(&i2c->dev, "Failed to request LDOENA GPIO: %d\n", ret);
+		goto err_enable;
+	}
+	if (wm5100->ldo_ena) {
+		gpiod_set_consumer_name(wm5100->ldo_ena, "WM5100 LDOENA");
 		msleep(2);
 	}
 
-	if (wm5100->pdata.reset) {
-		ret = gpio_request_one(wm5100->pdata.reset,
-				       GPIOF_OUT_INIT_HIGH, "WM5100 /RESET");
-		if (ret < 0) {
-			dev_err(&i2c->dev, "Failed to request /RESET %d: %d\n",
-				wm5100->pdata.reset, ret);
-			goto err_ldo;
-		}
+	wm5100->reset = devm_gpiod_get_optional(&i2c->dev, "reset",
+						GPIOD_OUT_LOW);
+	if (IS_ERR(wm5100->reset)) {
+		ret = PTR_ERR(wm5100->reset);
+		dev_err(&i2c->dev, "Failed to request /RESET GPIO: %d\n", ret);
+		goto err_ldo;
 	}
+	gpiod_set_consumer_name(wm5100->reset, "WM5100 /RESET");
 
 	ret = regmap_read(wm5100->regmap, WM5100_SOFTWARE_RESET, &reg);
 	if (ret < 0) {
@@ -2619,15 +2603,9 @@ static int wm5100_i2c_probe(struct i2c_client *i2c)
 	if (i2c->irq)
 		free_irq(i2c->irq, wm5100);
 	wm5100_free_gpio(i2c);
-	if (wm5100->pdata.reset) {
-		gpio_set_value_cansleep(wm5100->pdata.reset, 0);
-		gpio_free(wm5100->pdata.reset);
-	}
+	gpiod_set_value_cansleep(wm5100->reset, 1);
 err_ldo:
-	if (wm5100->pdata.ldo_ena) {
-		gpio_set_value_cansleep(wm5100->pdata.ldo_ena, 0);
-		gpio_free(wm5100->pdata.ldo_ena);
-	}
+	gpiod_set_value_cansleep(wm5100->ldo_ena, 0);
 err_enable:
 	regulator_bulk_disable(ARRAY_SIZE(wm5100->core_supplies),
 			       wm5100->core_supplies);
@@ -2643,14 +2621,8 @@ static void wm5100_i2c_remove(struct i2c_client *i2c)
 	if (i2c->irq)
 		free_irq(i2c->irq, wm5100);
 	wm5100_free_gpio(i2c);
-	if (wm5100->pdata.reset) {
-		gpio_set_value_cansleep(wm5100->pdata.reset, 0);
-		gpio_free(wm5100->pdata.reset);
-	}
-	if (wm5100->pdata.ldo_ena) {
-		gpio_set_value_cansleep(wm5100->pdata.ldo_ena, 0);
-		gpio_free(wm5100->pdata.ldo_ena);
-	}
+	gpiod_set_value_cansleep(wm5100->reset, 1);
+	gpiod_set_value_cansleep(wm5100->ldo_ena, 0);
 }
 
 #ifdef CONFIG_PM
@@ -2660,8 +2632,7 @@ static int wm5100_runtime_suspend(struct device *dev)
 
 	regcache_cache_only(wm5100->regmap, true);
 	regcache_mark_dirty(wm5100->regmap);
-	if (wm5100->pdata.ldo_ena)
-		gpio_set_value_cansleep(wm5100->pdata.ldo_ena, 0);
+	gpiod_set_value_cansleep(wm5100->ldo_ena, 0);
 	regulator_bulk_disable(ARRAY_SIZE(wm5100->core_supplies),
 			       wm5100->core_supplies);
 
@@ -2681,8 +2652,8 @@ static int wm5100_runtime_resume(struct device *dev)
 		return ret;
 	}
 
-	if (wm5100->pdata.ldo_ena) {
-		gpio_set_value_cansleep(wm5100->pdata.ldo_ena, 1);
+	if (wm5100->ldo_ena) {
+		gpiod_set_value_cansleep(wm5100->ldo_ena, 1);
 		msleep(2);
 	}
 

sound/soc/codecs/wm8996.c

@@ -14,7 +14,7 @@
 #include <linux/pm.h>
 #include <linux/gcd.h>
 #include <linux/gpio/driver.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/i2c.h>
 #include <linux/regmap.h>
 #include <linux/regulator/consumer.h>
@@ -51,7 +51,7 @@ struct wm8996_priv {
 	struct regmap *regmap;
 	struct snd_soc_component *component;
 
-	int ldo1ena;
+	struct gpio_desc *ldo_ena;
 
 	int sysclk;
 	int sysclk_src;
@@ -1596,9 +1596,9 @@ static int wm8996_set_bias_level(struct snd_soc_component *component,
 				return ret;
 			}
 
-			if (wm8996->pdata.ldo_ena >= 0) {
-				gpio_set_value_cansleep(wm8996->pdata.ldo_ena,
-							1);
+			if (wm8996->ldo_ena) {
+				gpiod_set_value_cansleep(wm8996->ldo_ena,
+							 1);
 				msleep(5);
 			}
 
@@ -1615,8 +1615,8 @@ static int wm8996_set_bias_level(struct snd_soc_component *component,
 
 	case SND_SOC_BIAS_OFF:
 		regcache_cache_only(wm8996->regmap, true);
-		if (wm8996->pdata.ldo_ena >= 0) {
-			gpio_set_value_cansleep(wm8996->pdata.ldo_ena, 0);
+		if (wm8996->ldo_ena) {
+			gpiod_set_value_cansleep(wm8996->ldo_ena, 0);
 			regcache_cache_only(wm8996->regmap, true);
 		}
 		regulator_bulk_disable(ARRAY_SIZE(wm8996->supplies),
@@ -2188,6 +2188,8 @@ static const struct gpio_chip wm8996_template_chip = {
 	.direction_input	= wm8996_gpio_direction_in,
 	.get			= wm8996_gpio_get,
 	.can_sleep		= 1,
+	.ngpio			= 5,
+	.base			= -1,
 };
 
 static void wm8996_init_gpio(struct wm8996_priv *wm8996)
@@ -2195,14 +2197,8 @@ static void wm8996_init_gpio(struct wm8996_priv *wm8996)
 	int ret;
 
 	wm8996->gpio_chip = wm8996_template_chip;
-	wm8996->gpio_chip.ngpio = 5;
 	wm8996->gpio_chip.parent = wm8996->dev;
 
-	if (wm8996->pdata.gpio_base)
-		wm8996->gpio_chip.base = wm8996->pdata.gpio_base;
-	else
-		wm8996->gpio_chip.base = -1;
-
 	ret = gpiochip_add_data(&wm8996->gpio_chip, wm8996);
 	if (ret != 0)
 		dev_err(wm8996->dev, "Failed to add GPIOs: %d\n", ret);
@@ -2771,15 +2767,15 @@ static int wm8996_i2c_probe(struct i2c_client *i2c)
 		memcpy(&wm8996->pdata, dev_get_platdata(&i2c->dev),
 		       sizeof(wm8996->pdata));
 
-	if (wm8996->pdata.ldo_ena > 0) {
-		ret = gpio_request_one(wm8996->pdata.ldo_ena,
-				       GPIOF_OUT_INIT_LOW, "WM8996 ENA");
-		if (ret < 0) {
-			dev_err(&i2c->dev, "Failed to request GPIO %d: %d\n",
-				wm8996->pdata.ldo_ena, ret);
-			goto err;
-		}
+	wm8996->ldo_ena = devm_gpiod_get_optional(&i2c->dev, "wlf,ldo1ena",
+						  GPIOD_OUT_LOW);
+	if (IS_ERR(wm8996->ldo_ena)) {
+		ret = PTR_ERR(wm8996->ldo_ena);
+		dev_err(&i2c->dev, "Failed to request LDO ENA GPIO: %d\n",
+			ret);
+		goto err;
 	}
+	gpiod_set_consumer_name(wm8996->ldo_ena, "WM8996 ENA");
 
 	for (i = 0; i < ARRAY_SIZE(wm8996->supplies); i++)
 		wm8996->supplies[i].supply = wm8996_supply_names[i];
@@ -2814,8 +2810,8 @@ static int wm8996_i2c_probe(struct i2c_client *i2c)
 		goto err_gpio;
 	}
 
-	if (wm8996->pdata.ldo_ena > 0) {
-		gpio_set_value_cansleep(wm8996->pdata.ldo_ena, 1);
+	if (wm8996->ldo_ena) {
+		gpiod_set_value_cansleep(wm8996->ldo_ena, 1);
 		msleep(5);
 	}
 
@@ -2847,8 +2843,8 @@ static int wm8996_i2c_probe(struct i2c_client *i2c)
 	dev_info(&i2c->dev, "revision %c\n",
 		 (reg & WM8996_CHIP_REV_MASK) + 'A');
 
-	if (wm8996->pdata.ldo_ena > 0) {
-		gpio_set_value_cansleep(wm8996->pdata.ldo_ena, 0);
+	if (wm8996->ldo_ena) {
+		gpiod_set_value_cansleep(wm8996->ldo_ena, 0);
 		regcache_cache_only(wm8996->regmap, true);
 	} else {
 		ret = regmap_write(wm8996->regmap, WM8996_SOFTWARE_RESET,
@@ -3054,12 +3050,10 @@ static int wm8996_i2c_probe(struct i2c_client *i2c)
 	wm8996_free_gpio(wm8996);
 err_regmap:
 err_enable:
-	if (wm8996->pdata.ldo_ena > 0)
-		gpio_set_value_cansleep(wm8996->pdata.ldo_ena, 0);
+	if (wm8996->ldo_ena)
+		gpiod_set_value_cansleep(wm8996->ldo_ena, 0);
 	regulator_bulk_disable(ARRAY_SIZE(wm8996->supplies), wm8996->supplies);
 err_gpio:
-	if (wm8996->pdata.ldo_ena > 0)
-		gpio_free(wm8996->pdata.ldo_ena);
 err:
 
 	return ret;
@@ -3070,10 +3064,8 @@ static void wm8996_i2c_remove(struct i2c_client *client)
 	struct wm8996_priv *wm8996 = i2c_get_clientdata(client);
 
 	wm8996_free_gpio(wm8996);
-	if (wm8996->pdata.ldo_ena > 0) {
-		gpio_set_value_cansleep(wm8996->pdata.ldo_ena, 0);
-		gpio_free(wm8996->pdata.ldo_ena);
-	}
+	if (wm8996->ldo_ena)
+		gpiod_set_value_cansleep(wm8996->ldo_ena, 0);
 }
 
 static const struct i2c_device_id wm8996_i2c_id[] = {