tty: serial: remove pnx8xxx uart driver

Commit 625326ea ("MIPS: Remove PNX833x alias NXP_STB22x") removed
support for PNX833x, so it's time to remove serial driver, too.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lore.kernel.org/r/20201106130332.103476-1-tsbogend@alpha.franken.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/tty/serial/Kconfig

@@ -703,22 +703,6 @@ config SERIAL_SH_SCI_DMA
 	depends on SERIAL_SH_SCI && DMA_ENGINE
 	default ARCH_RENESAS
 
-config SERIAL_PNX8XXX
-	bool "Enable PNX8XXX SoCs' UART Support"
-	depends on SOC_PNX833X
-	select SERIAL_CORE
-	help
-	  If you have a MIPS-based Philips SoC such as PNX8330 and you want
-	  to use serial ports, say Y.  Otherwise, say N.
-
-config SERIAL_PNX8XXX_CONSOLE
-	bool "Enable PNX8XX0 serial console"
-	depends on SERIAL_PNX8XXX
-	select SERIAL_CORE_CONSOLE
-	help
-	  If you have a MIPS-based Philips SoC such as PNX8330 and you want
-	  to use serial console, say Y. Otherwise, say N.
-
 config SERIAL_HS_LPC32XX
 	tristate "LPC32XX high speed serial port support"
 	depends on ARCH_LPC32XX || COMPILE_TEST

drivers/tty/serial/Makefile

@@ -27,7 +27,6 @@ obj-$(CONFIG_SERIAL_AMBA_PL010) += amba-pl010.o
 obj-$(CONFIG_SERIAL_AMBA_PL011) += amba-pl011.o
 obj-$(CONFIG_SERIAL_CLPS711X) += clps711x.o
 obj-$(CONFIG_SERIAL_PXA_NON8250) += pxa.o
-obj-$(CONFIG_SERIAL_PNX8XXX) += pnx8xxx_uart.o
 obj-$(CONFIG_SERIAL_SA1100) += sa1100.o
 obj-$(CONFIG_SERIAL_BCM63XX) += bcm63xx_uart.o
 obj-$(CONFIG_SERIAL_SAMSUNG) += samsung_tty.o

include/linux/serial_pnx8xxx.h

-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Embedded Alley Solutions, source@embeddedalley.com.
- */
-
-#ifndef _LINUX_SERIAL_PNX8XXX_H
-#define _LINUX_SERIAL_PNX8XXX_H
-
-#include <linux/serial_core.h>
-
-#define PNX8XXX_NR_PORTS	2
-
-struct pnx8xxx_port {
-	struct uart_port	port;
-	struct timer_list	timer;
-	unsigned int		old_status;
-};
-
-/* register offsets */
-#define PNX8XXX_LCR		0
-#define PNX8XXX_MCR		0x004
-#define PNX8XXX_BAUD		0x008
-#define PNX8XXX_CFG		0x00c
-#define PNX8XXX_FIFO		0x028
-#define PNX8XXX_ISTAT		0xfe0
-#define PNX8XXX_IEN		0xfe4
-#define PNX8XXX_ICLR		0xfe8
-#define PNX8XXX_ISET		0xfec
-#define PNX8XXX_PD		0xff4
-#define PNX8XXX_MID		0xffc
-
-#define PNX8XXX_UART_LCR_TXBREAK	(1<<30)
-#define PNX8XXX_UART_LCR_PAREVN		0x10000000
-#define PNX8XXX_UART_LCR_PAREN		0x08000000
-#define PNX8XXX_UART_LCR_2STOPB		0x04000000
-#define PNX8XXX_UART_LCR_8BIT		0x01000000
-#define PNX8XXX_UART_LCR_TX_RST		0x00040000
-#define PNX8XXX_UART_LCR_RX_RST		0x00020000
-#define PNX8XXX_UART_LCR_RX_NEXT	0x00010000
-
-#define PNX8XXX_UART_MCR_SCR		0xFF000000
-#define PNX8XXX_UART_MCR_DCD		0x00800000
-#define PNX8XXX_UART_MCR_CTS		0x00100000
-#define PNX8XXX_UART_MCR_LOOP		0x00000010
-#define PNX8XXX_UART_MCR_RTS		0x00000002
-#define PNX8XXX_UART_MCR_DTR		0x00000001
-
-#define PNX8XXX_UART_INT_TX		0x00000080
-#define PNX8XXX_UART_INT_EMPTY		0x00000040
-#define PNX8XXX_UART_INT_RCVTO		0x00000020
-#define PNX8XXX_UART_INT_RX		0x00000010
-#define PNX8XXX_UART_INT_RXOVRN		0x00000008
-#define PNX8XXX_UART_INT_FRERR		0x00000004
-#define PNX8XXX_UART_INT_BREAK		0x00000002
-#define PNX8XXX_UART_INT_PARITY		0x00000001
-#define PNX8XXX_UART_INT_ALLRX		0x0000003F
-#define PNX8XXX_UART_INT_ALLTX		0x000000C0
-
-#define PNX8XXX_UART_FIFO_TXFIFO	0x001F0000
-#define PNX8XXX_UART_FIFO_TXFIFO_STA	(0x1f<<16)
-#define PNX8XXX_UART_FIFO_RXBRK		0x00008000
-#define PNX8XXX_UART_FIFO_RXFE		0x00004000
-#define PNX8XXX_UART_FIFO_RXPAR		0x00002000
-#define PNX8XXX_UART_FIFO_RXFIFO	0x00001F00
-#define PNX8XXX_UART_FIFO_RBRTHR	0x000000FF
-
-#endif

include/uapi/linux/serial_core.h

@@ -134,8 +134,6 @@
 /*Digi jsm */
 #define PORT_JSM        69
 
-#define PORT_PNX8XXX	70
-
 /* SUN4V Hypervisor Console */
 #define PORT_SUNHV	72