Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

Pull more SCSI updates from James Bottomley:
 "The only new stuff which missed the first pull request is an update to
  the UFS driver.

  The rest is an assortment of bug fixes and minor tweaks which appeared
  recently (some are fixes for recent code and some are stuff spotted
  recently by the checkers or the new gcc-6 compiler [most of Arnd's
  stuff])"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (32 commits)
  scsi_common: do not clobber fixed sense information
  scsi: ufs: select CONFIG_NLS
  scsi: fc: use get/put_unaligned64 for wwn access
  fnic: move printk()s outside of the critical code section.
  qla2xxx: avoid maybe_uninitialized warning
  megaraid_sas: add missing curly braces in ioctl handler
  lpfc: fix misleading indentation
  scsi_transport_sas: add 'scsi_target_id' sysfs attribute
  scsi_dh_alua: uninitialized variable in alua_check_vpd()
  scsi: ufs-qcom: add printouts of testbus debug registers
  scsi: ufs-qcom: enable/disable the device ref clock
  scsi: ufs-qcom: set PA_Local_TX_LCC_Enable before link startup
  scsi: ufs: add device quirk delay before putting UFS rails in LPM
  scsi: ufs: fix leakage during link off state
  scsi: ufs: tune UniPro parameters to optimize hibern8 exit time
  scsi: ufs: handle non spec compliant bkops behaviour by device
  scsi: ufs: add retry for query descriptors
  scsi: ufs: add error recovery after DL NAC error
  scsi: ufs: make error handling bit faster
  scsi: ufs: disable vccq if it's not needed by UFS device
  ...

Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt

@@ -38,6 +38,9 @@ Optional properties:
 			  defined or a value in the array is "0" then it is assumed
 			  that the frequency is set by the parent clock or a
 			  fixed rate clock source.
+-lanes-per-direction	: number of lanes available per direction - either 1 or 2.
+			  Note that it is assume same number of lanes is used both
+			  directions at once. If not specified, default is 2 lanes per direction.
 
 Note: If above properties are not defined it can be assumed that the supply
 regulators or clocks are always on.

drivers/scsi/device_handler/scsi_dh_alua.c

@@ -332,7 +332,7 @@ static int alua_check_vpd(struct scsi_device *sdev, struct alua_dh_data *h,
 {
 	int rel_port = -1, group_id;
 	struct alua_port_group *pg, *old_pg = NULL;
-	bool pg_updated;
+	bool pg_updated = false;
 	unsigned long flags;
 
 	group_id = scsi_vpd_tpg_id(sdev, &rel_port);

drivers/scsi/fnic/fnic_scsi.c

@@ -958,23 +958,22 @@ static void fnic_fcpio_icmnd_cmpl_handler(struct fnic *fnic,
 	case FCPIO_INVALID_PARAM:    /* some parameter in request invalid */
 	case FCPIO_REQ_NOT_SUPPORTED:/* request type is not supported */
 	default:
-		shost_printk(KERN_ERR, fnic->lport->host, "hdr status = %s\n",
-			     fnic_fcpio_status_to_str(hdr_status));
 		sc->result = (DID_ERROR << 16) | icmnd_cmpl->scsi_status;
 		break;
 	}
 
-	if (hdr_status != FCPIO_SUCCESS) {
-		atomic64_inc(&fnic_stats->io_stats.io_failures);
-		shost_printk(KERN_ERR, fnic->lport->host, "hdr status = %s\n",
-			     fnic_fcpio_status_to_str(hdr_status));
-	}
 	/* Break link with the SCSI command */
 	CMD_SP(sc) = NULL;
 	CMD_FLAGS(sc) |= FNIC_IO_DONE;
 
 	spin_unlock_irqrestore(io_lock, flags);
 
+	if (hdr_status != FCPIO_SUCCESS) {
+		atomic64_inc(&fnic_stats->io_stats.io_failures);
+		shost_printk(KERN_ERR, fnic->lport->host, "hdr status = %s\n",
+			     fnic_fcpio_status_to_str(hdr_status));
+	}
+
 	fnic_release_ioreq_buf(fnic, io_req, sc);
 
 	mempool_free(io_req, fnic->io_req_pool);

drivers/scsi/lpfc/lpfc_init.c

@@ -2860,7 +2860,7 @@ lpfc_online(struct lpfc_hba *phba)
 	}
 
 	vports = lpfc_create_vport_work_array(phba);
-	if (vports != NULL)
+	if (vports != NULL) {
 		for (i = 0; i <= phba->max_vports && vports[i] != NULL; i++) {
 			struct Scsi_Host *shost;
 			shost = lpfc_shost_from_vport(vports[i]);
@@ -2877,7 +2877,8 @@ lpfc_online(struct lpfc_hba *phba)
 			}
 			spin_unlock_irq(shost->host_lock);
 		}
-		lpfc_destroy_vport_work_array(phba, vports);
+	}
+	lpfc_destroy_vport_work_array(phba, vports);
 
 	lpfc_unblock_mgmt_io(phba);
 	return 0;

drivers/scsi/megaraid/megaraid_sas.h

@@ -2097,7 +2097,7 @@ struct megasas_instance {
 	u8 UnevenSpanSupport;
 
 	u8 supportmax256vd;
-	u8 allow_fw_scan;
+	u8 pd_list_not_supported;
 	u16 fw_supported_vd_count;
 	u16 fw_supported_pd_count;
 

drivers/scsi/megaraid/megaraid_sas_base.c

@@ -1838,7 +1838,7 @@ static int megasas_slave_configure(struct scsi_device *sdev)
 	struct megasas_instance *instance;
 
 	instance = megasas_lookup_instance(sdev->host->host_no);
-	if (instance->allow_fw_scan) {
+	if (instance->pd_list_not_supported) {
 		if (sdev->channel < MEGASAS_MAX_PD_CHANNELS &&
 			sdev->type == TYPE_DISK) {
 			pd_index = (sdev->channel * MEGASAS_MAX_DEV_PER_CHANNEL) +
@@ -1874,7 +1874,8 @@ static int megasas_slave_alloc(struct scsi_device *sdev)
 		pd_index =
 			(sdev->channel * MEGASAS_MAX_DEV_PER_CHANNEL) +
 			sdev->id;
-		if ((instance->allow_fw_scan || instance->pd_list[pd_index].driveState ==
+		if ((instance->pd_list_not_supported ||
+			instance->pd_list[pd_index].driveState ==
 			MR_PD_STATE_SYSTEM)) {
 			goto scan_target;
 		}
@@ -4087,7 +4088,13 @@ megasas_get_pd_list(struct megasas_instance *instance)
 
 	switch (ret) {
 	case DCMD_FAILED:
-		megaraid_sas_kill_hba(instance);
+		dev_info(&instance->pdev->dev, "MR_DCMD_PD_LIST_QUERY "
+			"failed/not supported by firmware\n");
+
+		if (instance->ctrl_context)
+			megaraid_sas_kill_hba(instance);
+		else
+			instance->pd_list_not_supported = 1;
 		break;
 	case DCMD_TIMEOUT:
 
@@ -5034,7 +5041,6 @@ static int megasas_init_fw(struct megasas_instance *instance)
 	case PCI_DEVICE_ID_DELL_PERC5:
 	default:
 		instance->instancet = &megasas_instance_template_xscale;
-		instance->allow_fw_scan = 1;
 		break;
 	}
 
@@ -6650,12 +6656,13 @@ megasas_mgmt_fw_ioctl(struct megasas_instance *instance,
 	}
 
 	for (i = 0; i < ioc->sge_count; i++) {
-		if (kbuff_arr[i])
+		if (kbuff_arr[i]) {
 			dma_free_coherent(&instance->pdev->dev,
 					  le32_to_cpu(kern_sge32[i].length),
 					  kbuff_arr[i],
 					  le32_to_cpu(kern_sge32[i].phys_addr));
 			kbuff_arr[i] = NULL;
+		}
 	}
 
 	megasas_return_cmd(instance, cmd);

drivers/scsi/qla2xxx/qla_target.c

@@ -1881,15 +1881,17 @@ static int qlt_check_reserve_free_req(struct scsi_qla_host *vha,
 		else
 			vha->req->cnt = vha->req->length -
 			    (vha->req->ring_index - cnt);
-	}
 
-	if (unlikely(vha->req->cnt < (req_cnt + 2))) {
-		ql_dbg(ql_dbg_io, vha, 0x305a,
-		    "qla_target(%d): There is no room in the request ring: vha->req->ring_index=%d, vha->req->cnt=%d, req_cnt=%d Req-out=%d Req-in=%d Req-Length=%d\n",
-		    vha->vp_idx, vha->req->ring_index,
-		    vha->req->cnt, req_cnt, cnt, cnt_in, vha->req->length);
-		return -EAGAIN;
+		if (unlikely(vha->req->cnt < (req_cnt + 2))) {
+			ql_dbg(ql_dbg_io, vha, 0x305a,
+			    "qla_target(%d): There is no room in the request ring: vha->req->ring_index=%d, vha->req->cnt=%d, req_cnt=%d Req-out=%d Req-in=%d Req-Length=%d\n",
+			    vha->vp_idx, vha->req->ring_index,
+			    vha->req->cnt, req_cnt, cnt, cnt_in,
+			    vha->req->length);
+			return -EAGAIN;
+		}
 	}
+
 	vha->req->cnt -= req_cnt;
 
 	return 0;

drivers/scsi/scsi_common.c

@@ -278,8 +278,16 @@ int scsi_set_sense_information(u8 *buf, int buf_len, u64 info)
 		ucp[3] = 0;
 		put_unaligned_be64(info, &ucp[4]);
 	} else if ((buf[0] & 0x7f) == 0x70) {
-		buf[0] |= 0x80;
-		put_unaligned_be64(info, &buf[3]);
+		/*
+		 * Only set the 'VALID' bit if we can represent the value
+		 * correctly; otherwise just fill out the lower bytes and
+		 * clear the 'VALID' flag.
+		 */
+		if (info <= 0xffffffffUL)
+			buf[0] |= 0x80;
+		else
+			buf[0] &= 0x7f;
+		put_unaligned_be32((u32)info, &buf[3]);
 	}
 
 	return 0;

drivers/scsi/scsi_sas_internal.h

@@ -4,7 +4,7 @@
 #define SAS_HOST_ATTRS		0
 #define SAS_PHY_ATTRS		17
 #define SAS_PORT_ATTRS		1
-#define SAS_RPORT_ATTRS		7
+#define SAS_RPORT_ATTRS		8
 #define SAS_END_DEV_ATTRS	5
 #define SAS_EXPANDER_ATTRS	7
 

drivers/scsi/scsi_sysfs.c

@@ -1105,7 +1105,7 @@ static umode_t scsi_sdev_bin_attr_is_visible(struct kobject *kobj,
 	if (attr == &dev_attr_vpd_pg80 && !sdev->vpd_pg80)
 		return 0;
 
-	if (attr == &dev_attr_vpd_pg83 && sdev->vpd_pg83)
+	if (attr == &dev_attr_vpd_pg83 && !sdev->vpd_pg83)
 		return 0;
 
 	return S_IRUGO;

drivers/scsi/scsi_transport_sas.c

@@ -1286,6 +1286,7 @@ sas_rphy_protocol_attr(identify.target_port_protocols, target_port_protocols);
 sas_rphy_simple_attr(identify.sas_address, sas_address, "0x%016llx\n",
 		unsigned long long);
 sas_rphy_simple_attr(identify.phy_identifier, phy_identifier, "%d\n", u8);
+sas_rphy_simple_attr(scsi_target_id, scsi_target_id, "%d\n", u32);
 
 /* only need 8 bytes of data plus header (4 or 8) */
 #define BUF_SIZE 64
@@ -1886,6 +1887,7 @@ sas_attach_transport(struct sas_function_template *ft)
 	SETUP_RPORT_ATTRIBUTE(rphy_device_type);
 	SETUP_RPORT_ATTRIBUTE(rphy_sas_address);
 	SETUP_RPORT_ATTRIBUTE(rphy_phy_identifier);
+	SETUP_RPORT_ATTRIBUTE(rphy_scsi_target_id);
 	SETUP_OPTIONAL_RPORT_ATTRIBUTE(rphy_enclosure_identifier,
 				       get_enclosure_identifier);
 	SETUP_OPTIONAL_RPORT_ATTRIBUTE(rphy_bay_identifier,

drivers/scsi/ufs/Kconfig

@@ -37,6 +37,7 @@ config SCSI_UFSHCD
 	depends on SCSI && SCSI_DMA
 	select PM_DEVFREQ
 	select DEVFREQ_GOV_SIMPLE_ONDEMAND
+	select NLS
 	---help---
 	This selects the support for UFS devices in Linux, say Y and make
 	  sure that you know the name of your UFS host adapter (the card

drivers/scsi/ufs/ufs-qcom.c

 /*
- * Copyright (c) 2013-2015, Linux Foundation. All rights reserved.
+ * Copyright (c) 2013-2016, Linux Foundation. All rights reserved.
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 and
@@ -16,8 +16,8 @@
 #include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/phy/phy.h>
-
 #include <linux/phy/phy-qcom-ufs.h>
+
 #include "ufshcd.h"
 #include "ufshcd-pltfrm.h"
 #include "unipro.h"
@@ -58,6 +58,12 @@ static void ufs_qcom_dump_regs(struct ufs_hba *hba, int offset, int len,
 			len * 4, false);
 }
 
+static void ufs_qcom_dump_regs_wrapper(struct ufs_hba *hba, int offset, int len,
+		char *prefix, void *priv)
+{
+	ufs_qcom_dump_regs(hba, offset, len, prefix);
+}
+
 static int ufs_qcom_get_connected_tx_lanes(struct ufs_hba *hba, u32 *tx_lanes)
 {
 	int err = 0;
@@ -106,9 +112,11 @@ static void ufs_qcom_disable_lane_clks(struct ufs_qcom_host *host)
 	if (!host->is_lane_clks_enabled)
 		return;
 
-	clk_disable_unprepare(host->tx_l1_sync_clk);
+	if (host->hba->lanes_per_direction > 1)
+		clk_disable_unprepare(host->tx_l1_sync_clk);
 	clk_disable_unprepare(host->tx_l0_sync_clk);
-	clk_disable_unprepare(host->rx_l1_sync_clk);
+	if (host->hba->lanes_per_direction > 1)
+		clk_disable_unprepare(host->rx_l1_sync_clk);
 	clk_disable_unprepare(host->rx_l0_sync_clk);
 
 	host->is_lane_clks_enabled = false;
@@ -132,21 +140,24 @@ static int ufs_qcom_enable_lane_clks(struct ufs_qcom_host *host)
 	if (err)
 		goto disable_rx_l0;
 
-	err = ufs_qcom_host_clk_enable(dev, "rx_lane1_sync_clk",
-		host->rx_l1_sync_clk);
-	if (err)
-		goto disable_tx_l0;
+	if (host->hba->lanes_per_direction > 1) {
+		err = ufs_qcom_host_clk_enable(dev, "rx_lane1_sync_clk",
+			host->rx_l1_sync_clk);
+		if (err)
+			goto disable_tx_l0;
 
-	err = ufs_qcom_host_clk_enable(dev, "tx_lane1_sync_clk",
-		host->tx_l1_sync_clk);
-	if (err)
-		goto disable_rx_l1;
+		err = ufs_qcom_host_clk_enable(dev, "tx_lane1_sync_clk",
+			host->tx_l1_sync_clk);
+		if (err)
+			goto disable_rx_l1;
+	}
 
 	host->is_lane_clks_enabled = true;
 	goto out;
 
 disable_rx_l1:
-	clk_disable_unprepare(host->rx_l1_sync_clk);
+	if (host->hba->lanes_per_direction > 1)
+		clk_disable_unprepare(host->rx_l1_sync_clk);
 disable_tx_l0:
 	clk_disable_unprepare(host->tx_l0_sync_clk);
 disable_rx_l0:
@@ -170,14 +181,16 @@ static int ufs_qcom_init_lane_clks(struct ufs_qcom_host *host)
 	if (err)
 		goto out;
 
-	err = ufs_qcom_host_clk_get(dev, "rx_lane1_sync_clk",
-		&host->rx_l1_sync_clk);
-	if (err)
-		goto out;
-
-	err = ufs_qcom_host_clk_get(dev, "tx_lane1_sync_clk",
-		&host->tx_l1_sync_clk);
+	/* In case of single lane per direction, don't read lane1 clocks */
+	if (host->hba->lanes_per_direction > 1) {
+		err = ufs_qcom_host_clk_get(dev, "rx_lane1_sync_clk",
+			&host->rx_l1_sync_clk);
+		if (err)
+			goto out;
 
+		err = ufs_qcom_host_clk_get(dev, "tx_lane1_sync_clk",
+			&host->tx_l1_sync_clk);
+	}
 out:
 	return err;
 }
@@ -267,9 +280,8 @@ static int ufs_qcom_power_up_sequence(struct ufs_hba *hba)
 	ret = ufs_qcom_phy_calibrate_phy(phy, is_rate_B);
 
 	if (ret) {
-		dev_err(hba->dev,
-		"%s: ufs_qcom_phy_calibrate_phy()failed, ret = %d\n",
-		__func__, ret);
+		dev_err(hba->dev, "%s: ufs_qcom_phy_calibrate_phy() failed, ret = %d\n",
+			__func__, ret);
 		goto out;
 	}
 
@@ -519,6 +531,18 @@ static int ufs_qcom_link_startup_notify(struct ufs_hba *hba,
 			err = ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div(hba,
 									  150);
 
+		/*
+		 * Some UFS devices (and may be host) have issues if LCC is
+		 * enabled. So we are setting PA_Local_TX_LCC_Enable to 0
+		 * before link startup which will make sure that both host
+		 * and device TX LCC are disabled once link startup is
+		 * completed.
+		 */
+		if (ufshcd_get_local_unipro_ver(hba) != UFS_UNIPRO_VER_1_41)
+			err = ufshcd_dme_set(hba,
+					UIC_ARG_MIB(PA_LOCAL_TX_LCC_ENABLE),
+					0);
+
 		break;
 	case POST_CHANGE:
 		ufs_qcom_link_startup_post_change(hba);
@@ -962,6 +986,10 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
 			goto out;
 		}
 
+		/* enable the device ref clock before changing to HS mode */
+		if (!ufshcd_is_hs_mode(&hba->pwr_info) &&
+			ufshcd_is_hs_mode(dev_req_params))
+			ufs_qcom_dev_ref_clk_ctrl(host, true);
 		break;
 	case POST_CHANGE:
 		if (ufs_qcom_cfg_timers(hba, dev_req_params->gear_rx,
@@ -989,6 +1017,11 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
 		memcpy(&host->dev_req_params,
 				dev_req_params, sizeof(*dev_req_params));
 		ufs_qcom_update_bus_bw_vote(host);
+
+		/* disable the device ref clock if entered PWM mode */
+		if (ufshcd_is_hs_mode(&hba->pwr_info) &&
+			!ufshcd_is_hs_mode(dev_req_params))
+			ufs_qcom_dev_ref_clk_ctrl(host, false);
 		break;
 	default:
 		ret = -EINVAL;
@@ -1090,6 +1123,9 @@ static int ufs_qcom_setup_clocks(struct ufs_hba *hba, bool on)
 			ufs_qcom_phy_disable_iface_clk(host->generic_phy);
 			goto out;
 		}
+		/* enable the device ref clock for HS mode*/
+		if (ufshcd_is_hs_mode(&hba->pwr_info))
+			ufs_qcom_dev_ref_clk_ctrl(host, true);
 		vote = host->bus_vote.saved_vote;
 		if (vote == host->bus_vote.min_bw_vote)
 			ufs_qcom_update_bus_bw_vote(host);
@@ -1367,6 +1403,74 @@ static int ufs_qcom_clk_scale_notify(struct ufs_hba *hba,
 	return err;
 }
 
+static void ufs_qcom_print_hw_debug_reg_all(struct ufs_hba *hba,
+		void *priv, void (*print_fn)(struct ufs_hba *hba,
+		int offset, int num_regs, char *str, void *priv))
+{
+	u32 reg;
+	struct ufs_qcom_host *host;
+
+	if (unlikely(!hba)) {
+		pr_err("%s: hba is NULL\n", __func__);
+		return;
+	}
+	if (unlikely(!print_fn)) {
+		dev_err(hba->dev, "%s: print_fn is NULL\n", __func__);
+		return;
+	}
+
+	host = ufshcd_get_variant(hba);
+	if (!(host->dbg_print_en & UFS_QCOM_DBG_PRINT_REGS_EN))
+		return;
+
+	reg = ufs_qcom_get_debug_reg_offset(host, UFS_UFS_DBG_RD_REG_OCSC);
+	print_fn(hba, reg, 44, "UFS_UFS_DBG_RD_REG_OCSC ", priv);
+
+	reg = ufshcd_readl(hba, REG_UFS_CFG1);
+	reg |= UFS_BIT(17);
+	ufshcd_writel(hba, reg, REG_UFS_CFG1);
+
+	reg = ufs_qcom_get_debug_reg_offset(host, UFS_UFS_DBG_RD_EDTL_RAM);
+	print_fn(hba, reg, 32, "UFS_UFS_DBG_RD_EDTL_RAM ", priv);
+
+	reg = ufs_qcom_get_debug_reg_offset(host, UFS_UFS_DBG_RD_DESC_RAM);
+	print_fn(hba, reg, 128, "UFS_UFS_DBG_RD_DESC_RAM ", priv);
+
+	reg = ufs_qcom_get_debug_reg_offset(host, UFS_UFS_DBG_RD_PRDT_RAM);
+	print_fn(hba, reg, 64, "UFS_UFS_DBG_RD_PRDT_RAM ", priv);
+
+	ufshcd_writel(hba, (reg & ~UFS_BIT(17)), REG_UFS_CFG1);
+
+	reg = ufs_qcom_get_debug_reg_offset(host, UFS_DBG_RD_REG_UAWM);
+	print_fn(hba, reg, 4, "UFS_DBG_RD_REG_UAWM ", priv);
+
+	reg = ufs_qcom_get_debug_reg_offset(host, UFS_DBG_RD_REG_UARM);
+	print_fn(hba, reg, 4, "UFS_DBG_RD_REG_UARM ", priv);
+
+	reg = ufs_qcom_get_debug_reg_offset(host, UFS_DBG_RD_REG_TXUC);
+	print_fn(hba, reg, 48, "UFS_DBG_RD_REG_TXUC ", priv);
+
+	reg = ufs_qcom_get_debug_reg_offset(host, UFS_DBG_RD_REG_RXUC);
+	print_fn(hba, reg, 27, "UFS_DBG_RD_REG_RXUC ", priv);
+
+	reg = ufs_qcom_get_debug_reg_offset(host, UFS_DBG_RD_REG_DFC);
+	print_fn(hba, reg, 19, "UFS_DBG_RD_REG_DFC ", priv);
+
+	reg = ufs_qcom_get_debug_reg_offset(host, UFS_DBG_RD_REG_TRLUT);
+	print_fn(hba, reg, 34, "UFS_DBG_RD_REG_TRLUT ", priv);
+
+	reg = ufs_qcom_get_debug_reg_offset(host, UFS_DBG_RD_REG_TMRLUT);
+	print_fn(hba, reg, 9, "UFS_DBG_RD_REG_TMRLUT ", priv);
+}
+
+static void ufs_qcom_enable_test_bus(struct ufs_qcom_host *host)
+{
+	if (host->dbg_print_en & UFS_QCOM_DBG_PRINT_TEST_BUS_EN)
+		ufshcd_rmwl(host->hba, TEST_BUS_EN, TEST_BUS_EN, REG_UFS_CFG1);
+	else
+		ufshcd_rmwl(host->hba, TEST_BUS_EN, 0, REG_UFS_CFG1);
+}
+
 static void ufs_qcom_get_default_testbus_cfg(struct ufs_qcom_host *host)
 {
 	/* provide a legal default configuration */
@@ -1475,6 +1579,7 @@ int ufs_qcom_testbus_config(struct ufs_qcom_host *host)
 	ufshcd_rmwl(host->hba, mask,
 		    (u32)host->testbus.select_minor << offset,
 		    reg);
+	ufs_qcom_enable_test_bus(host);
 	ufshcd_release(host->hba);
 	pm_runtime_put_sync(host->hba->dev);
 
@@ -1491,8 +1596,10 @@ static void ufs_qcom_dump_dbg_regs(struct ufs_hba *hba)
 	ufs_qcom_dump_regs(hba, REG_UFS_SYS1CLK_1US, 16,
 			"HCI Vendor Specific Registers ");
 
+	ufs_qcom_print_hw_debug_reg_all(hba, NULL, ufs_qcom_dump_regs_wrapper);
 	ufs_qcom_testbus_read(hba);
 }
+
 /**
  * struct ufs_hba_qcom_vops - UFS QCOM specific variant operations
  *
@@ -1537,7 +1644,7 @@ static int ufs_qcom_probe(struct platform_device *pdev)
  * ufs_qcom_remove - set driver_data of the device to NULL
  * @pdev: pointer to platform device handle
  *
- * Always return 0
+ * Always returns 0
  */
 static int ufs_qcom_remove(struct platform_device *pdev)
 {

drivers/scsi/ufs/ufs-qcom.h

@@ -241,6 +241,15 @@ struct ufs_qcom_host {
 	struct ufs_qcom_testbus testbus;
 };
 
+static inline u32
+ufs_qcom_get_debug_reg_offset(struct ufs_qcom_host *host, u32 reg)
+{
+	if (host->hw_ver.major <= 0x02)
+		return UFS_CNTLR_2_x_x_VEN_REGS_OFFSET(reg);
+
+	return UFS_CNTLR_3_x_x_VEN_REGS_OFFSET(reg);
+};
+
 #define ufs_qcom_is_link_off(hba) ufshcd_is_link_off(hba)
 #define ufs_qcom_is_link_active(hba) ufshcd_is_link_active(hba)
 #define ufs_qcom_is_link_hibern8(hba) ufshcd_is_link_hibern8(hba)

drivers/scsi/ufs/ufs.h

@@ -43,6 +43,7 @@
 #define GENERAL_UPIU_REQUEST_SIZE 32
 #define QUERY_DESC_MAX_SIZE       255
 #define QUERY_DESC_MIN_SIZE       2
+#define QUERY_DESC_HDR_SIZE       2
 #define QUERY_OSF_SIZE            (GENERAL_UPIU_REQUEST_SIZE - \
 					(sizeof(struct utp_upiu_header)))
 
@@ -195,6 +196,37 @@ enum unit_desc_param {
 	UNIT_DESC_PARAM_LARGE_UNIT_SIZE_M1	= 0x22,
 };
 
+/* Device descriptor parameters offsets in bytes*/
+enum device_desc_param {
+	DEVICE_DESC_PARAM_LEN			= 0x0,
+	DEVICE_DESC_PARAM_TYPE			= 0x1,
+	DEVICE_DESC_PARAM_DEVICE_TYPE		= 0x2,
+	DEVICE_DESC_PARAM_DEVICE_CLASS		= 0x3,
+	DEVICE_DESC_PARAM_DEVICE_SUB_CLASS	= 0x4,
+	DEVICE_DESC_PARAM_PRTCL			= 0x5,
+	DEVICE_DESC_PARAM_NUM_LU		= 0x6,
+	DEVICE_DESC_PARAM_NUM_WLU		= 0x7,
+	DEVICE_DESC_PARAM_BOOT_ENBL		= 0x8,
+	DEVICE_DESC_PARAM_DESC_ACCSS_ENBL	= 0x9,
+	DEVICE_DESC_PARAM_INIT_PWR_MODE		= 0xA,
+	DEVICE_DESC_PARAM_HIGH_PR_LUN		= 0xB,
+	DEVICE_DESC_PARAM_SEC_RMV_TYPE		= 0xC,
+	DEVICE_DESC_PARAM_SEC_LU		= 0xD,
+	DEVICE_DESC_PARAM_BKOP_TERM_LT		= 0xE,
+	DEVICE_DESC_PARAM_ACTVE_ICC_LVL		= 0xF,
+	DEVICE_DESC_PARAM_SPEC_VER		= 0x10,
+	DEVICE_DESC_PARAM_MANF_DATE		= 0x12,
+	DEVICE_DESC_PARAM_MANF_NAME		= 0x14,
+	DEVICE_DESC_PARAM_PRDCT_NAME		= 0x15,
+	DEVICE_DESC_PARAM_SN			= 0x16,
+	DEVICE_DESC_PARAM_OEM_ID		= 0x17,
+	DEVICE_DESC_PARAM_MANF_ID		= 0x18,
+	DEVICE_DESC_PARAM_UD_OFFSET		= 0x1A,
+	DEVICE_DESC_PARAM_UD_LEN		= 0x1B,
+	DEVICE_DESC_PARAM_RTT_CAP		= 0x1C,
+	DEVICE_DESC_PARAM_FRQ_RTC		= 0x1D,
+};
+
 /*
  * Logical Unit Write Protect
  * 00h: LU not write protected
@@ -469,6 +501,7 @@ struct ufs_vreg {
 	struct regulator *reg;
 	const char *name;
 	bool enabled;
+	bool unused;
 	int min_uV;
 	int max_uV;
 	int min_uA;

drivers/scsi/ufs/ufs_quirks.h

+/*
+ * Copyright (c) 2014-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef _UFS_QUIRKS_H_
+#define _UFS_QUIRKS_H_
+
+/* return true if s1 is a prefix of s2 */
+#define STR_PRFX_EQUAL(s1, s2) !strncmp(s1, s2, strlen(s1))
+
+#define UFS_ANY_VENDOR 0xFFFF
+#define UFS_ANY_MODEL  "ANY_MODEL"
+
+#define MAX_MODEL_LEN 16
+
+#define UFS_VENDOR_TOSHIBA     0x198
+#define UFS_VENDOR_SAMSUNG     0x1CE
+
+/**
+ * ufs_device_info - ufs device details
+ * @wmanufacturerid: card details
+ * @model: card model
+ */
+struct ufs_device_info {
+	u16 wmanufacturerid;
+	char model[MAX_MODEL_LEN + 1];
+};
+
+/**
+ * ufs_dev_fix - ufs device quirk info
+ * @card: ufs card details
+ * @quirk: device quirk
+ */
+struct ufs_dev_fix {
+	struct ufs_device_info card;
+	unsigned int quirk;
+};
+
+#define END_FIX { { 0 }, 0 }
+
+/* add specific device quirk */
+#define UFS_FIX(_vendor, _model, _quirk) \
+		{					  \
+			.card.wmanufacturerid = (_vendor),\
+			.card.model = (_model),		  \
+			.quirk = (_quirk),		  \
+		}
+
+/*
+ * If UFS device is having issue in processing LCC (Line Control
+ * Command) coming from UFS host controller then enable this quirk.
+ * When this quirk is enabled, host controller driver should disable
+ * the LCC transmission on UFS host controller (by clearing
+ * TX_LCC_ENABLE attribute of host to 0).
+ */
+#define UFS_DEVICE_QUIRK_BROKEN_LCC (1 << 0)
+
+/*
+ * Some UFS devices don't need VCCQ rail for device operations. Enabling this
+ * quirk for such devices will make sure that VCCQ rail is not voted.
+ */
+#define UFS_DEVICE_NO_VCCQ (1 << 1)
+
+/*
+ * Some vendor's UFS device sends back to back NACs for the DL data frames
+ * causing the host controller to raise the DFES error status. Sometimes
+ * such UFS devices send back to back NAC without waiting for new
+ * retransmitted DL frame from the host and in such cases it might be possible
+ * the Host UniPro goes into bad state without raising the DFES error
+ * interrupt. If this happens then all the pending commands would timeout
+ * only after respective SW command (which is generally too large).
+ *
+ * We can workaround such device behaviour like this:
+ * - As soon as SW sees the DL NAC error, it should schedule the error handler
+ * - Error handler would sleep for 50ms to see if there are any fatal errors
+ *   raised by UFS controller.
+ *    - If there are fatal errors then SW does normal error recovery.
+ *    - If there are no fatal errors then SW sends the NOP command to device
+ *      to check if link is alive.
+ *        - If NOP command times out, SW does normal error recovery
+ *        - If NOP command succeed, skip the error handling.
+ *
+ * If DL NAC error is seen multiple times with some vendor's UFS devices then
+ * enable this quirk to initiate quick error recovery and also silence related
+ * error logs to reduce spamming of kernel logs.
+ */
+#define UFS_DEVICE_QUIRK_RECOVERY_FROM_DL_NAC_ERRORS (1 << 2)
+
+/*
+ * Some UFS devices may not work properly after resume if the link was kept
+ * in off state during suspend. Enabling this quirk will not allow the
+ * link to be kept in off state during suspend.
+ */
+#define UFS_DEVICE_QUIRK_NO_LINK_OFF	(1 << 3)
+
+/*
+ * Few Toshiba UFS device models advertise RX_MIN_ACTIVATETIME_CAPABILITY as
+ * 600us which may not be enough for reliable hibern8 exit hardware sequence
+ * from UFS device.
+ * To workaround this issue, host should set its PA_TACTIVATE time to 1ms even
+ * if device advertises RX_MIN_ACTIVATETIME_CAPABILITY less than 1ms.
+ */
+#define UFS_DEVICE_QUIRK_PA_TACTIVATE	(1 << 4)
+
+/*
+ * Some UFS memory devices may have really low read/write throughput in
+ * FAST AUTO mode, enable this quirk to make sure that FAST AUTO mode is
+ * never enabled for such devices.
+ */
+#define UFS_DEVICE_NO_FASTAUTO		(1 << 5)
+
+/*
+ * It seems some UFS devices may keep drawing more than sleep current
+ * (atleast for 500us) from UFS rails (especially from VCCQ rail).
+ * To avoid this situation, add 2ms delay before putting these UFS
+ * rails in LPM mode.
+ */
+#define UFS_DEVICE_QUIRK_DELAY_BEFORE_LPM	(1 << 6)
+
+struct ufs_hba;
+void ufs_advertise_fixup_device(struct ufs_hba *hba);
+
+static struct ufs_dev_fix ufs_fixups[] = {
+	/* UFS cards deviations table */
+	UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL,
+		UFS_DEVICE_QUIRK_DELAY_BEFORE_LPM),
+	UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL, UFS_DEVICE_NO_VCCQ),
+	UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL,
+		UFS_DEVICE_QUIRK_RECOVERY_FROM_DL_NAC_ERRORS),
+	UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL,
+		UFS_DEVICE_NO_FASTAUTO),
+	UFS_FIX(UFS_VENDOR_TOSHIBA, UFS_ANY_MODEL,
+		UFS_DEVICE_QUIRK_DELAY_BEFORE_LPM),
+	UFS_FIX(UFS_VENDOR_TOSHIBA, "THGLF2G9C8KBADG",
+		UFS_DEVICE_QUIRK_PA_TACTIVATE),
+	UFS_FIX(UFS_VENDOR_TOSHIBA, "THGLF2G9D8KBADG",
+		UFS_DEVICE_QUIRK_PA_TACTIVATE),
+
+	END_FIX
+};
+#endif /* UFS_QUIRKS_H_ */

drivers/scsi/ufs/ufshcd-pltfrm.c

@@ -40,6 +40,8 @@
 #include "ufshcd.h"
 #include "ufshcd-pltfrm.h"
 
+#define UFSHCD_DEFAULT_LANES_PER_DIRECTION		2
+
 static int ufshcd_parse_clock_info(struct ufs_hba *hba)
 {
 	int ret = 0;
@@ -277,6 +279,21 @@ void ufshcd_pltfrm_shutdown(struct platform_device *pdev)
 }
 EXPORT_SYMBOL_GPL(ufshcd_pltfrm_shutdown);
 
+static void ufshcd_init_lanes_per_dir(struct ufs_hba *hba)
+{
+	struct device *dev = hba->dev;
+	int ret;
+
+	ret = of_property_read_u32(dev->of_node, "lanes-per-direction",
+		&hba->lanes_per_direction);
+	if (ret) {
+		dev_dbg(hba->dev,
+			"%s: failed to read lanes-per-direction, ret=%d\n",
+			__func__, ret);
+		hba->lanes_per_direction = UFSHCD_DEFAULT_LANES_PER_DIRECTION;
+	}
+}
+
 /**
  * ufshcd_pltfrm_init - probe routine of the driver
  * @pdev: pointer to Platform device handle
@@ -331,6 +348,8 @@ int ufshcd_pltfrm_init(struct platform_device *pdev,
 	pm_runtime_set_active(&pdev->dev);
 	pm_runtime_enable(&pdev->dev);
 
+	ufshcd_init_lanes_per_dir(hba);
+
 	err = ufshcd_init(hba, mmio_base, irq);
 	if (err) {
 		dev_err(dev, "Initialization failed\n");

drivers/scsi/ufs/ufshcd.h

@@ -54,6 +54,7 @@
 #include <linux/clk.h>
 #include <linux/completion.h>
 #include <linux/regulator/consumer.h>
+#include "unipro.h"
 
 #include <asm/irq.h>
 #include <asm/byteorder.h>
@@ -383,6 +384,9 @@ struct ufs_init_prefetch {
  * @clk_list_head: UFS host controller clocks list node head
  * @pwr_info: holds current power mode
  * @max_pwr_info: keeps the device max valid pwm
+ * @urgent_bkops_lvl: keeps track of urgent bkops level for device
+ * @is_urgent_bkops_lvl_checked: keeps track if the urgent bkops level for
+ *  device is known or not.
  */
 struct ufs_hba {
 	void __iomem *mmio_base;
@@ -470,6 +474,9 @@ struct ufs_hba {
 
 	unsigned int quirks;	/* Deviations from standard UFSHCI spec. */
 
+	/* Device deviations from standard UFS device spec. */
+	unsigned int dev_quirks;
+
 	wait_queue_head_t tm_wq;
 	wait_queue_head_t tm_tag_wq;
 	unsigned long tm_condition;
@@ -509,6 +516,8 @@ struct ufs_hba {
 
 	bool wlun_dev_clr_ua;
 
+	/* Number of lanes available (1 or 2) for Rx/Tx */
+	u32 lanes_per_direction;
 	struct ufs_pa_layer_attr pwr_info;
 	struct ufs_pwr_mode_info max_pwr_info;
 
@@ -533,6 +542,9 @@ struct ufs_hba {
 	struct devfreq *devfreq;
 	struct ufs_clk_scaling clk_scaling;
 	bool is_sys_suspended;
+
+	enum bkops_status urgent_bkops_lvl;
+	bool is_urgent_bkops_lvl_checked;
 };
 
 /* Returns true if clocks can be gated. Otherwise false */
@@ -588,15 +600,9 @@ int ufshcd_alloc_host(struct device *, struct ufs_hba **);
 void ufshcd_dealloc_host(struct ufs_hba *);
 int ufshcd_init(struct ufs_hba * , void __iomem * , unsigned int);
 void ufshcd_remove(struct ufs_hba *);
-
-/**
- * ufshcd_hba_stop - Send controller to reset state
- * @hba: per adapter instance
- */
-static inline void ufshcd_hba_stop(struct ufs_hba *hba)
-{
-	ufshcd_writel(hba, CONTROLLER_DISABLE,  REG_CONTROLLER_ENABLE);
-}
+int ufshcd_wait_for_register(struct ufs_hba *hba, u32 reg, u32 mask,
+				u32 val, unsigned long interval_us,
+				unsigned long timeout_ms, bool can_sleep);
 
 static inline void check_upiu_size(void)
 {
@@ -682,11 +688,27 @@ static inline int ufshcd_dme_peer_get(struct ufs_hba *hba,
 	return ufshcd_dme_get_attr(hba, attr_sel, mib_val, DME_PEER);
 }
 
+int ufshcd_read_device_desc(struct ufs_hba *hba, u8 *buf, u32 size);
+
+static inline bool ufshcd_is_hs_mode(struct ufs_pa_layer_attr *pwr_info)
+{
+	return (pwr_info->pwr_rx == FAST_MODE ||
+		pwr_info->pwr_rx == FASTAUTO_MODE) &&
+		(pwr_info->pwr_tx == FAST_MODE ||
+		pwr_info->pwr_tx == FASTAUTO_MODE);
+}
+
+#define ASCII_STD true
+
+int ufshcd_read_string_desc(struct ufs_hba *hba, int desc_index, u8 *buf,
+				u32 size, bool ascii);
+
 /* Expose Query-Request API */
 int ufshcd_query_flag(struct ufs_hba *hba, enum query_opcode opcode,
 	enum flag_idn idn, bool *flag_res);
 int ufshcd_hold(struct ufs_hba *hba, bool async);
 void ufshcd_release(struct ufs_hba *hba);
+u32 ufshcd_get_local_unipro_ver(struct ufs_hba *hba);
 
 /* Wrapper functions for safely calling variant operations */
 static inline const char *ufshcd_get_var_name(struct ufs_hba *hba)

drivers/scsi/ufs/ufshci.h

@@ -92,6 +92,7 @@ enum {
 	UFSHCI_VERSION_10 = 0x00010000, /* 1.0 */
 	UFSHCI_VERSION_11 = 0x00010100, /* 1.1 */
 	UFSHCI_VERSION_20 = 0x00000200, /* 2.0 */
+	UFSHCI_VERSION_21 = 0x00000210, /* 2.1 */
 };
 
 /*
@@ -170,6 +171,8 @@ enum {
 #define UIC_DATA_LINK_LAYER_ERROR		UFS_BIT(31)
 #define UIC_DATA_LINK_LAYER_ERROR_CODE_MASK	0x7FFF
 #define UIC_DATA_LINK_LAYER_ERROR_PA_INIT	0x2000
+#define UIC_DATA_LINK_LAYER_ERROR_NAC_RECEIVED	0x0001
+#define UIC_DATA_LINK_LAYER_ERROR_TCx_REPLAY_TIMEOUT 0x0002
 
 /* UECN - Host UIC Error Code Network Layer 40h */
 #define UIC_NETWORK_LAYER_ERROR			UFS_BIT(31)
@@ -209,6 +212,7 @@ enum {
 
 /* GenSelectorIndex calculation macros for M-PHY attributes */
 #define UIC_ARG_MPHY_TX_GEN_SEL_INDEX(lane) (lane)
+#define UIC_ARG_MPHY_RX_GEN_SEL_INDEX(lane) (PA_MAXDATALANES + (lane))
 
 #define UIC_ARG_MIB_SEL(attr, sel)	((((attr) & 0xFFFF) << 16) |\
 					 ((sel) & 0xFFFF))

drivers/scsi/ufs/unipro.h

@@ -15,6 +15,7 @@
 /*
  * M-TX Configuration Attributes
  */
+#define TX_HIBERN8TIME_CAPABILITY		0x000F
 #define TX_MODE					0x0021
 #define TX_HSRATE_SERIES			0x0022
 #define TX_HSGEAR				0x0023
@@ -48,8 +49,12 @@
 #define RX_ENTER_HIBERN8			0x00A7
 #define RX_BYPASS_8B10B_ENABLE			0x00A8
 #define RX_TERMINATION_FORCE_ENABLE		0x0089
+#define RX_MIN_ACTIVATETIME_CAPABILITY		0x008F
+#define RX_HIBERN8TIME_CAPABILITY		0x0092
 
 #define is_mphy_tx_attr(attr)			(attr < RX_MODE)
+#define RX_MIN_ACTIVATETIME_UNIT_US		100
+#define HIBERN8TIME_UNIT_US			100
 /*
  * PHY Adpater attributes
  */
@@ -70,6 +75,7 @@
 #define PA_MAXRXSPEEDFAST	0x1541
 #define PA_MAXRXSPEEDSLOW	0x1542
 #define PA_TXLINKSTARTUPHS	0x1544
+#define PA_LOCAL_TX_LCC_ENABLE	0x155E
 #define PA_TXSPEEDFAST		0x1565
 #define PA_TXSPEEDSLOW		0x1566
 #define PA_REMOTEVERINFO	0x15A0
@@ -110,6 +116,12 @@
 #define PA_STALLNOCONFIGTIME	0x15A3
 #define PA_SAVECONFIGTIME	0x15A4
 
+#define PA_TACTIVATE_TIME_UNIT_US	10
+#define PA_HIBERN8_TIME_UNIT_US		100
+
+/* PHY Adapter Protocol Constants */
+#define PA_MAXDATALANES	4
+
 /* PA power modes */
 enum {
 	FAST_MODE	= 1,
@@ -143,6 +155,16 @@ enum ufs_hs_gear_tag {
 	UFS_HS_G3,		/* HS Gear 3 */
 };
 
+enum ufs_unipro_ver {
+	UFS_UNIPRO_VER_RESERVED = 0,
+	UFS_UNIPRO_VER_1_40 = 1, /* UniPro version 1.40 */
+	UFS_UNIPRO_VER_1_41 = 2, /* UniPro version 1.41 */
+	UFS_UNIPRO_VER_1_6 = 3,  /* UniPro version 1.6 */
+	UFS_UNIPRO_VER_MAX = 4,  /* UniPro unsupported version */
+	/* UniPro version field mask in PA_LOCALVERINFO */
+	UFS_UNIPRO_VER_MASK = 0xF,
+};
+
 /*
  * Data Link Layer Attributes
  */

include/scsi/scsi_transport_fc.h

@@ -28,6 +28,7 @@
 #define SCSI_TRANSPORT_FC_H
 
 #include <linux/sched.h>
+#include <asm/unaligned.h>
 #include <scsi/scsi.h>
 #include <scsi/scsi_netlink.h>
 
@@ -797,22 +798,12 @@ fc_remote_port_chkready(struct fc_rport *rport)
 
 static inline u64 wwn_to_u64(u8 *wwn)
 {
-	return (u64)wwn[0] << 56 | (u64)wwn[1] << 48 |
-	    (u64)wwn[2] << 40 | (u64)wwn[3] << 32 |
-	    (u64)wwn[4] << 24 | (u64)wwn[5] << 16 |
-	    (u64)wwn[6] <<  8 | (u64)wwn[7];
+	return get_unaligned_be64(wwn);
 }
 
 static inline void u64_to_wwn(u64 inm, u8 *wwn)
 {
-	wwn[0] = (inm >> 56) & 0xff;
-	wwn[1] = (inm >> 48) & 0xff;
-	wwn[2] = (inm >> 40) & 0xff;
-	wwn[3] = (inm >> 32) & 0xff;
-	wwn[4] = (inm >> 24) & 0xff;
-	wwn[5] = (inm >> 16) & 0xff;
-	wwn[6] = (inm >> 8) & 0xff;
-	wwn[7] = inm & 0xff;
+	put_unaligned_be64(inm, wwn);
 }
 
 /**