defxx: Correct DEFEA's ESIC port I/O accesses

Reverse the order of arguments to `outb', data to write comes first.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/fddi/defxx.c

@@ -719,28 +719,28 @@ static void dfx_bus_init(struct net_device *dev)
 
 		/* Set the decode range of the board.  */
 		val = ((bp->base.port >> 12) << PI_IO_CMP_V_SLOT);
-		outb(base_addr + PI_ESIC_K_IO_ADD_CMP_0_1, val);
-		outb(base_addr + PI_ESIC_K_IO_ADD_CMP_0_0, 0);
-		outb(base_addr + PI_ESIC_K_IO_ADD_CMP_1_1, val);
-		outb(base_addr + PI_ESIC_K_IO_ADD_CMP_1_0, 0);
+		outb(val, base_addr + PI_ESIC_K_IO_ADD_CMP_0_1);
+		outb(0, base_addr + PI_ESIC_K_IO_ADD_CMP_0_0);
+		outb(val, base_addr + PI_ESIC_K_IO_ADD_CMP_1_1);
+		outb(0, base_addr + PI_ESIC_K_IO_ADD_CMP_1_0);
 		val = PI_ESIC_K_CSR_IO_LEN - 1;
-		outb(base_addr + PI_ESIC_K_IO_ADD_MASK_0_1, (val >> 8) & 0xff);
-		outb(base_addr + PI_ESIC_K_IO_ADD_MASK_0_0, val & 0xff);
-		outb(base_addr + PI_ESIC_K_IO_ADD_MASK_1_1, (val >> 8) & 0xff);
-		outb(base_addr + PI_ESIC_K_IO_ADD_MASK_1_0, val & 0xff);
+		outb(val, base_addr + PI_ESIC_K_IO_ADD_MASK_0_1);
+		outb(0, base_addr + PI_ESIC_K_IO_ADD_MASK_0_0);
+		outb(val, base_addr + PI_ESIC_K_IO_ADD_MASK_1_1);
+		outb(0, base_addr + PI_ESIC_K_IO_ADD_MASK_1_0);
 
 		/* Enable the decoders.  */
 		val = PI_FUNCTION_CNTRL_M_IOCS1 | PI_FUNCTION_CNTRL_M_IOCS0;
 		if (dfx_use_mmio)
 			val |= PI_FUNCTION_CNTRL_M_MEMCS0;
-		outb(base_addr + PI_ESIC_K_FUNCTION_CNTRL, val);
+		outb(val, base_addr + PI_ESIC_K_FUNCTION_CNTRL);
 
 		/*
 		 * Enable access to the rest of the module
 		 * (including PDQ and packet memory).
 		 */
 		val = PI_SLOT_CNTRL_M_ENB;
-		outb(base_addr + PI_ESIC_K_SLOT_CNTRL, val);
+		outb(val, base_addr + PI_ESIC_K_SLOT_CNTRL);
 
 		/*
 		 * Map PDQ registers into memory or port space.  This is
@@ -751,12 +751,12 @@ static void dfx_bus_init(struct net_device *dev)
 			val |= PI_BURST_HOLDOFF_V_MEM_MAP;
 		else
 			val &= ~PI_BURST_HOLDOFF_V_MEM_MAP;
-		outb(base_addr + PI_DEFEA_K_BURST_HOLDOFF, val);
+		outb(val, base_addr + PI_DEFEA_K_BURST_HOLDOFF);
 
 		/* Enable interrupts at EISA bus interface chip (ESIC) */
 		val = inb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0);
 		val |= PI_CONFIG_STAT_0_M_INT_ENB;
-		outb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0, val);
+		outb(val, base_addr + PI_ESIC_K_IO_CONFIG_STAT_0);
 	}
 	if (dfx_bus_pci) {
 		struct pci_dev *pdev = to_pci_dev(bdev);
@@ -825,7 +825,7 @@ static void dfx_bus_uninit(struct net_device *dev)
 		/* Disable interrupts at EISA bus interface chip (ESIC) */
 		val = inb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0);
 		val &= ~PI_CONFIG_STAT_0_M_INT_ENB;
-		outb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0, val);
+		outb(val, base_addr + PI_ESIC_K_IO_CONFIG_STAT_0);
 	}
 	if (dfx_bus_pci) {
 		/* Disable interrupts at PCI bus interface chip (PFI) */
@@ -1917,7 +1917,7 @@ static irqreturn_t dfx_interrupt(int irq, void *dev_id)
 
 		/* Disable interrupts at the ESIC */
 		status &= ~PI_CONFIG_STAT_0_M_INT_ENB;
-		outb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0, status);
+		outb(status, base_addr + PI_ESIC_K_IO_CONFIG_STAT_0);
 
 		/* Call interrupt service routine for this adapter */
 		dfx_int_common(dev);
@@ -1925,7 +1925,7 @@ static irqreturn_t dfx_interrupt(int irq, void *dev_id)
 		/* Reenable interrupts at the ESIC */
 		status = inb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0);
 		status |= PI_CONFIG_STAT_0_M_INT_ENB;
-		outb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0, status);
+		outb(status, base_addr + PI_ESIC_K_IO_CONFIG_STAT_0);
 
 		spin_unlock(&bp->lock);
 	}