Commit 8a6be2bd authored by Xie Xiaobo's avatar Xie Xiaobo Committed by Scott Wood

powerpc/85xx: Add TWR-P1025 board support

TWR-P1025 Overview
 -----------------
 512Mbyte DDR3 (on board DDR)
 64MB Nor Flash
 eTSEC1: Connected to RGMII PHY AR8035
 eTSEC3: Connected to RGMII PHY AR8035
 Two USB2.0 Type A
 One microSD Card slot
 One mini-PCIe slot
 One mini-USB TypeB dual UART
Signed-off-by: default avatarMichael Johnston <michael.johnston@freescale.com>
Signed-off-by: default avatarXie Xiaobo <X.Xie@freescale.com>
[scottwood@freescale.com: use pr_info rather than KERN_INFO]
Signed-off-by: default avatarScott Wood <scottwood@freescale.com>
parent 72c916ae
* Solomon SSD1289 Framebuffer Driver
Required properties:
- compatible: Should be "solomon,ssd1289fb". The only supported bus for
now is lbc.
- reg: Should contain address of the controller on the LBC bus. The detail
was described in Documentation/devicetree/bindings/powerpc/fsl/lbc.txt
Examples:
display@2,0 {
compatible = "solomon,ssd1289fb";
reg = <0x2 0x0000 0x0004>;
};
/*
* P1025 TWR Device Tree Source (32-bit address map)
*
* Copyright 2013 Freescale Semiconductor Inc.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* * Neither the name of Freescale Semiconductor nor the
* names of its contributors may be used to endorse or promote products
* derived from this software without specific prior written permission.
*
*
* ALTERNATIVELY, this software may be distributed under the terms of the
* GNU General Public License ("GPL") as published by the Free Software
* Foundation, either version 2 of that License or (at your option) any
* later version.
*
* THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
/include/ "fsl/p1021si-pre.dtsi"
/ {
model = "fsl,P1025";
compatible = "fsl,TWR-P1025";
memory {
device_type = "memory";
};
lbc: localbus@ffe05000 {
reg = <0 0xffe05000 0 0x1000>;
/* NOR Flash and SSD1289 */
ranges = <0x0 0x0 0x0 0xec000000 0x04000000
0x2 0x0 0x0 0xe0000000 0x00020000>;
};
soc: soc@ffe00000 {
ranges = <0x0 0x0 0xffe00000 0x100000>;
};
pci0: pcie@ffe09000 {
ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
reg = <0 0xffe09000 0 0x1000>;
pcie@0 {
ranges = <0x2000000 0x0 0xa0000000
0x2000000 0x0 0xa0000000
0x0 0x20000000
0x1000000 0x0 0x0
0x1000000 0x0 0x0
0x0 0x100000>;
};
};
pci1: pcie@ffe0a000 {
reg = <0 0xffe0a000 0 0x1000>;
ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
pcie@0 {
ranges = <0x2000000 0x0 0x80000000
0x2000000 0x0 0x80000000
0x0 0x20000000
0x1000000 0x0 0x0
0x1000000 0x0 0x0
0x0 0x100000>;
};
};
qe: qe@ffe80000 {
ranges = <0x0 0x0 0xffe80000 0x40000>;
reg = <0 0xffe80000 0 0x480>;
brg-frequency = <0>;
bus-frequency = <0>;
};
};
/include/ "p1025twr.dtsi"
/include/ "fsl/p1021si-post.dtsi"
/*
* P1025 TWR Device Tree Source stub (no addresses or top-level ranges)
*
* Copyright 2013 Freescale Semiconductor Inc.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* * Neither the name of Freescale Semiconductor nor the
* names of its contributors may be used to endorse or promote products
* derived from this software without specific prior written permission.
*
*
* ALTERNATIVELY, this software may be distributed under the terms of the
* GNU General Public License ("GPL") as published by the Free Software
* Foundation, either version 2 of that License or (at your option) any
* later version.
*
* THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
/{
aliases {
ethernet3 = &enet3;
ethernet4 = &enet4;
};
};
&lbc {
nor@0,0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "cfi-flash";
reg = <0x0 0x0 0x4000000>;
bank-width = <2>;
device-width = <1>;
partition@0 {
/* This location must not be altered */
/* 256KB for Vitesse 7385 Switch firmware */
reg = <0x0 0x00040000>;
label = "NOR Vitesse-7385 Firmware";
read-only;
};
partition@40000 {
/* 256KB for DTB Image */
reg = <0x00040000 0x00040000>;
label = "NOR DTB Image";
};
partition@80000 {
/* 5.5 MB for Linux Kernel Image */
reg = <0x00080000 0x00580000>;
label = "NOR Linux Kernel Image";
};
partition@400000 {
/* 56.75MB for Root file System */
reg = <0x00600000 0x038c0000>;
label = "NOR Root File System";
};
partition@ec0000 {
/* This location must not be altered */
/* 256KB for QE ucode firmware*/
reg = <0x03ec0000 0x00040000>;
label = "NOR QE microcode firmware";
read-only;
};
partition@f00000 {
/* This location must not be altered */
/* 512KB for u-boot Bootloader Image */
/* 512KB for u-boot Environment Variables */
reg = <0x03f00000 0x00100000>;
label = "NOR U-Boot Image";
read-only;
};
};
/* CS2 for Display */
display@2,0 {
compatible = "solomon,ssd1289fb";
reg = <0x2 0x0000 0x0004>;
};
};
&soc {
usb@22000 {
phy_type = "ulpi";
};
mdio@24000 {
phy0: ethernet-phy@2 {
interrupt-parent = <&mpic>;
interrupts = <1 1 0 0>;
reg = <0x2>;
};
phy1: ethernet-phy@1 {
interrupt-parent = <&mpic>;
interrupts = <2 1 0 0>;
reg = <0x1>;
};
tbi0: tbi-phy@11 {
reg = <0x11>;
device_type = "tbi-phy";
};
};
mdio@25000 {
tbi1: tbi-phy@11 {
reg = <0x11>;
device_type = "tbi-phy";
};
};
mdio@26000 {
tbi2: tbi-phy@11 {
reg = <0x11>;
device_type = "tbi-phy";
};
};
enet0: ethernet@b0000 {
phy-handle = <&phy0>;
phy-connection-type = "rgmii-id";
};
enet1: ethernet@b1000 {
status = "disabled";
};
enet2: ethernet@b2000 {
phy-handle = <&phy1>;
phy-connection-type = "rgmii-id";
};
par_io@e0100 {
#address-cells = <1>;
#size-cells = <1>;
reg = <0xe0100 0x60>;
ranges = <0x0 0xe0100 0x60>;
device_type = "par_io";
num-ports = <3>;
pio1: ucc_pin@01 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */
0x0 0x17 0x2 0x0 0x2 0x0 /* CLK12 */
0x0 0x18 0x2 0x0 0x1 0x0 /* CLK9 */
0x0 0x7 0x1 0x0 0x2 0x0 /* ENET1_TXD0_SER1_TXD0 */
0x0 0x9 0x1 0x0 0x2 0x0 /* ENET1_TXD1_SER1_TXD1 */
0x0 0xb 0x1 0x0 0x2 0x0 /* ENET1_TXD2_SER1_TXD2 */
0x0 0xc 0x1 0x0 0x2 0x0 /* ENET1_TXD3_SER1_TXD3 */
0x0 0x6 0x2 0x0 0x2 0x0 /* ENET1_RXD0_SER1_RXD0 */
0x0 0xa 0x2 0x0 0x2 0x0 /* ENET1_RXD1_SER1_RXD1 */
0x0 0xe 0x2 0x0 0x2 0x0 /* ENET1_RXD2_SER1_RXD2 */
0x0 0xf 0x2 0x0 0x2 0x0 /* ENET1_RXD3_SER1_RXD3 */
0x0 0x5 0x1 0x0 0x2 0x0 /* ENET1_TX_EN_SER1_RTS_B */
0x0 0xd 0x1 0x0 0x2 0x0 /* ENET1_TX_ER */
0x0 0x4 0x2 0x0 0x2 0x0 /* ENET1_RX_DV_SER1_CTS_B */
0x0 0x8 0x2 0x0 0x2 0x0 /* ENET1_RX_ER_SER1_CD_B */
0x0 0x11 0x2 0x0 0x2 0x0 /* ENET1_CRS */
0x0 0x10 0x2 0x0 0x2 0x0>; /* ENET1_COL */
};
pio2: ucc_pin@02 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */
0x1 0xb 0x2 0x0 0x1 0x0 /* CLK13 */
0x1 0x7 0x1 0x0 0x2 0x0 /* ENET5_TXD0_SER5_TXD0 */
0x1 0xa 0x1 0x0 0x2 0x0 /* ENET5_TXD1_SER5_TXD1 */
0x1 0x6 0x2 0x0 0x2 0x0 /* ENET5_RXD0_SER5_RXD0 */
0x1 0x9 0x2 0x0 0x2 0x0 /* ENET5_RXD1_SER5_RXD1 */
0x1 0x5 0x1 0x0 0x2 0x0 /* ENET5_TX_EN_SER5_RTS_B */
0x1 0x4 0x2 0x0 0x2 0x0 /* ENET5_RX_DV_SER5_CTS_B */
0x1 0x8 0x2 0x0 0x2 0x0>; /* ENET5_RX_ER_SER5_CD_B */
};
pio3: ucc_pin@03 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x0 0x16 0x2 0x0 0x2 0x0 /* SER7_CD_B*/
0x0 0x12 0x2 0x0 0x2 0x0 /* SER7_CTS_B*/
0x0 0x13 0x1 0x0 0x2 0x0 /* SER7_RTS_B*/
0x0 0x14 0x2 0x0 0x2 0x0 /* SER7_RXD0*/
0x0 0x15 0x1 0x0 0x2 0x0>; /* SER7_TXD0*/
};
pio4: ucc_pin@04 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x1 0x0 0x2 0x0 0x2 0x0 /* SER3_CD_B*/
0x0 0x1c 0x2 0x0 0x2 0x0 /* SER3_CTS_B*/
0x0 0x1d 0x1 0x0 0x2 0x0 /* SER3_RTS_B*/
0x0 0x1e 0x2 0x0 0x2 0x0 /* SER3_RXD0*/
0x0 0x1f 0x1 0x0 0x2 0x0>; /* SER3_TXD0*/
};
};
};
&qe {
enet3: ucc@2000 {
device_type = "network";
compatible = "ucc_geth";
rx-clock-name = "clk12";
tx-clock-name = "clk9";
pio-handle = <&pio1>;
phy-handle = <&qe_phy0>;
phy-connection-type = "mii";
};
mdio@2120 {
qe_phy0: ethernet-phy@18 {
interrupt-parent = <&mpic>;
interrupts = <4 1 0 0>;
reg = <0x18>;
device_type = "ethernet-phy";
};
qe_phy1: ethernet-phy@19 {
interrupt-parent = <&mpic>;
interrupts = <5 1 0 0>;
reg = <0x19>;
device_type = "ethernet-phy";
};
tbi-phy@11 {
reg = <0x11>;
device_type = "tbi-phy";
};
};
enet4: ucc@2400 {
device_type = "network";
compatible = "ucc_geth";
rx-clock-name = "none";
tx-clock-name = "clk13";
pio-handle = <&pio2>;
phy-handle = <&qe_phy1>;
phy-connection-type = "rmii";
};
serial2: ucc@2600 {
device_type = "serial";
compatible = "ucc_uart";
port-number = <0>;
rx-clock-name = "brg6";
tx-clock-name = "brg6";
pio-handle = <&pio3>;
};
serial3: ucc@2200 {
device_type = "serial";
compatible = "ucc_uart";
port-number = <1>;
rx-clock-name = "brg2";
tx-clock-name = "brg2";
pio-handle = <&pio4>;
};
};
......@@ -123,6 +123,12 @@ config P1023_RDS
help
This option enables support for the P1023 RDS and RDB boards
config TWR_P102x
bool "Freescale TWR-P102x"
select DEFAULT_UIMAGE
help
This option enables support for the TWR-P1025 board.
config SOCRATES
bool "Socrates"
select DEFAULT_UIMAGE
......
......@@ -18,6 +18,7 @@ obj-$(CONFIG_P1010_RDB) += p1010rdb.o
obj-$(CONFIG_P1022_DS) += p1022_ds.o
obj-$(CONFIG_P1022_RDK) += p1022_rdk.o
obj-$(CONFIG_P1023_RDS) += p1023_rds.o
obj-$(CONFIG_TWR_P102x) += twr_p102x.o
obj-$(CONFIG_CORENET_GENERIC) += corenet_generic.o
obj-$(CONFIG_STX_GP3) += stx_gp3.o
obj-$(CONFIG_TQM85xx) += tqm85xx.o
......
/*
* Copyright 2010-2011, 2013 Freescale Semiconductor, Inc.
*
* Author: Michael Johnston <michael.johnston@freescale.com>
*
* Description:
* TWR-P102x Board Setup
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/errno.h>
#include <linux/pci.h>
#include <linux/of_platform.h>
#include <asm/pci-bridge.h>
#include <asm/udbg.h>
#include <asm/mpic.h>
#include <asm/qe.h>
#include <asm/qe_ic.h>
#include <asm/fsl_guts.h>
#include <sysdev/fsl_soc.h>
#include <sysdev/fsl_pci.h>
#include "smp.h"
#include "mpc85xx.h"
static void __init twr_p1025_pic_init(void)
{
struct mpic *mpic;
#ifdef CONFIG_QUICC_ENGINE
struct device_node *np;
#endif
mpic = mpic_alloc(NULL, 0, MPIC_BIG_ENDIAN |
MPIC_SINGLE_DEST_CPU,
0, 256, " OpenPIC ");
BUG_ON(mpic == NULL);
mpic_init(mpic);
#ifdef CONFIG_QUICC_ENGINE
np = of_find_compatible_node(NULL, NULL, "fsl,qe-ic");
if (np) {
qe_ic_init(np, 0, qe_ic_cascade_low_mpic,
qe_ic_cascade_high_mpic);
of_node_put(np);
} else
pr_err("Could not find qe-ic node\n");
#endif
}
/* ************************************************************************
*
* Setup the architecture
*
*/
static void __init twr_p1025_setup_arch(void)
{
#ifdef CONFIG_QUICC_ENGINE
struct device_node *np;
#endif
if (ppc_md.progress)
ppc_md.progress("twr_p1025_setup_arch()", 0);
mpc85xx_smp_init();
fsl_pci_assign_primary();
#ifdef CONFIG_QUICC_ENGINE
mpc85xx_qe_init();
#if defined(CONFIG_UCC_GETH) || defined(CONFIG_SERIAL_QE)
if (machine_is(twr_p1025)) {
struct ccsr_guts __iomem *guts;
np = of_find_compatible_node(NULL, NULL, "fsl,p1021-guts");
if (np) {
guts = of_iomap(np, 0);
if (!guts)
pr_err("twr_p1025: could not map global utilities register\n");
else {
/* P1025 has pins muxed for QE and other functions. To
* enable QE UEC mode, we need to set bit QE0 for UCC1
* in Eth mode, QE0 and QE3 for UCC5 in Eth mode, QE9
* and QE12 for QE MII management signals in PMUXCR
* register.
* Set QE mux bits in PMUXCR */
setbits32(&guts->pmuxcr, MPC85xx_PMUXCR_QE(0) |
MPC85xx_PMUXCR_QE(3) |
MPC85xx_PMUXCR_QE(9) |
MPC85xx_PMUXCR_QE(12));
iounmap(guts);
#if defined(CONFIG_SERIAL_QE)
/* On P1025TWR board, the UCC7 acted as UART port.
* However, The UCC7's CTS pin is low level in default,
* it will impact the transmission in full duplex
* communication. So disable the Flow control pin PA18.
* The UCC7 UART just can use RXD and TXD pins.
*/
par_io_config_pin(0, 18, 0, 0, 0, 0);
#endif
/* Drive PB29 to CPLD low - CPLD will then change
* muxing from LBC to QE */
par_io_config_pin(1, 29, 1, 0, 0, 0);
par_io_data_set(1, 29, 0);
}
of_node_put(np);
}
}
#endif
#endif /* CONFIG_QUICC_ENGINE */
pr_info("TWR-P1025 board from Freescale Semiconductor\n");
}
machine_arch_initcall(twr_p1025, mpc85xx_common_publish_devices);
static int __init twr_p1025_probe(void)
{
unsigned long root = of_get_flat_dt_root();
return of_flat_dt_is_compatible(root, "fsl,TWR-P1025");
}
define_machine(twr_p1025) {
.name = "TWR-P1025",
.probe = twr_p1025_probe,
.setup_arch = twr_p1025_setup_arch,
.init_IRQ = twr_p1025_pic_init,
#ifdef CONFIG_PCI
.pcibios_fixup_bus = fsl_pcibios_fixup_bus,
#endif
.get_irq = mpic_get_irq,
.restart = fsl_rstcr_restart,
.calibrate_decr = generic_calibrate_decr,
.progress = udbg_progress,
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment