Commit 8abd16a6 authored by Mark Brown's avatar Mark Brown

ASoC: Add WM8903 interrupt support

Currently used to detect completion of the write sequencer.
Signed-off-by: default avatarMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: default avatarLiam Girdwood <lrg@slimlogic.co.uk>
parent 37f88e84
......@@ -232,6 +232,8 @@
#define WM8903_GP5_DB_WIDTH 1 /* GP5_DB */
struct wm8903_platform_data {
bool irq_active_low; /* Set if IRQ active low, default high */
/* Default register value for R6 (Mic bias), used to configure
* microphone detection. In conjunction with gpio_cfg this
* can be used to route the microphone status signals out onto
......
......@@ -12,12 +12,12 @@
* TODO:
* - TDM mode configuration.
* - Digital microphone support.
* - Interrupt support (mic detect and sequencer).
*/
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/init.h>
#include <linux/completion.h>
#include <linux/delay.h>
#include <linux/pm.h>
#include <linux/i2c.h>
......@@ -29,6 +29,7 @@
#include <sound/soc.h>
#include <sound/soc-dapm.h>
#include <sound/initval.h>
#include <sound/wm8903.h>
#include "wm8903.h"
......@@ -220,6 +221,8 @@ struct wm8903_priv {
int playback_active;
int capture_active;
struct completion wseq;
struct snd_pcm_substream *master_substream;
struct snd_pcm_substream *slave_substream;
};
......@@ -242,6 +245,7 @@ static int wm8903_run_sequence(struct snd_soc_codec *codec, unsigned int start)
{
u16 reg[5];
struct i2c_client *i2c = codec->control_data;
struct wm8903_priv *wm8903 = codec->private_data;
BUG_ON(start > 48);
......@@ -256,11 +260,11 @@ static int wm8903_run_sequence(struct snd_soc_codec *codec, unsigned int start)
start | WM8903_WSEQ_START);
/* Wait for it to complete. If we have the interrupt wired up then
* we could block waiting for an interrupt, though polling may still
* be desirable for diagnostic purposes.
* that will break us out of the poll early.
*/
do {
msleep(10);
wait_for_completion_timeout(&wm8903->wseq,
msecs_to_jiffies(10));
reg[4] = snd_soc_read(codec, WM8903_WRITE_SEQUENCER_4);
} while (reg[4] & WM8903_WSEQ_BUSY);
......@@ -1433,6 +1437,22 @@ static int wm8903_hw_params(struct snd_pcm_substream *substream,
return 0;
}
static irqreturn_t wm8903_irq(int irq, void *data)
{
struct wm8903_priv *wm8903 = data;
struct snd_soc_codec *codec = &wm8903->codec;
int reg;
reg = snd_soc_read(codec, WM8903_INTERRUPT_STATUS_1);
if (reg & WM8903_WSEQ_BUSY_EINT) {
dev_dbg(codec->dev, "Write sequencer done\n");
complete(&wm8903->wseq);
}
return IRQ_HANDLED;
}
#define WM8903_PLAYBACK_RATES (SNDRV_PCM_RATE_8000 |\
SNDRV_PCM_RATE_11025 | \
SNDRV_PCM_RATE_16000 | \
......@@ -1527,9 +1547,11 @@ static struct snd_soc_codec *wm8903_codec;
static __devinit int wm8903_i2c_probe(struct i2c_client *i2c,
const struct i2c_device_id *id)
{
struct wm8903_platform_data *pdata = dev_get_platdata(&i2c->dev);
struct wm8903_priv *wm8903;
struct snd_soc_codec *codec;
int ret, i;
int trigger, irq_pol;
u16 val;
wm8903 = kzalloc(sizeof(struct wm8903_priv), GFP_KERNEL);
......@@ -1553,6 +1575,7 @@ static __devinit int wm8903_i2c_probe(struct i2c_client *i2c,
codec->reg_cache = &wm8903->reg_cache[0];
codec->private_data = wm8903;
codec->volatile_register = wm8903_volatile_register;
init_completion(&wm8903->wseq);
i2c_set_clientdata(i2c, codec);
codec->control_data = i2c;
......@@ -1596,6 +1619,32 @@ static __devinit int wm8903_i2c_probe(struct i2c_client *i2c,
wm8903->mic_delay = pdata->micdet_delay;
}
if (i2c->irq) {
if (pdata && pdata->irq_active_low) {
trigger = IRQF_TRIGGER_LOW;
irq_pol = WM8903_IRQ_POL;
} else {
trigger = IRQF_TRIGGER_HIGH;
irq_pol = 0;
}
snd_soc_update_bits(codec, WM8903_INTERRUPT_CONTROL,
WM8903_IRQ_POL, irq_pol);
ret = request_threaded_irq(i2c->irq, NULL, wm8903_irq,
trigger | IRQF_ONESHOT,
"wm8903", wm8903);
if (ret != 0) {
dev_err(&i2c->dev, "Failed to request IRQ: %d\n",
ret);
goto err;
}
/* Enable write sequencer interrupts */
snd_soc_update_bits(codec, WM8903_INTERRUPT_STATUS_1_MASK,
WM8903_IM_WSEQ_BUSY_EINT, 0);
}
/* power on device */
wm8903_set_bias_level(codec, SND_SOC_BIAS_STANDBY);
......@@ -1637,7 +1686,7 @@ static __devinit int wm8903_i2c_probe(struct i2c_client *i2c,
ret = snd_soc_register_codec(codec);
if (ret != 0) {
dev_err(&i2c->dev, "Failed to register codec: %d\n", ret);
goto err;
goto err_irq;
}
ret = snd_soc_register_dai(&wm8903_dai);
......@@ -1650,6 +1699,9 @@ static __devinit int wm8903_i2c_probe(struct i2c_client *i2c,
err_codec:
snd_soc_unregister_codec(codec);
err_irq:
if (i2c->irq)
free_irq(i2c->irq, wm8903);
err:
wm8903_codec = NULL;
kfree(wm8903);
......@@ -1659,12 +1711,16 @@ static __devinit int wm8903_i2c_probe(struct i2c_client *i2c,
static __devexit int wm8903_i2c_remove(struct i2c_client *client)
{
struct snd_soc_codec *codec = i2c_get_clientdata(client);
struct wm8903_priv *priv = codec->private_data;
snd_soc_unregister_dai(&wm8903_dai);
snd_soc_unregister_codec(codec);
wm8903_set_bias_level(codec, SND_SOC_BIAS_OFF);
if (client->irq)
free_irq(client->irq, priv);
kfree(codec->private_data);
wm8903_codec = NULL;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment