Commit 8b834bff authored by Ming Lei's avatar Ming Lei Committed by Martin K. Petersen

scsi: hpsa: fix selection of reply queue

Since commit 84676c1f ("genirq/affinity: assign vectors to all
possible CPUs") we could end up with an MSI-X vector that did not have
any online CPUs mapped. This would lead to I/O hangs since there was no
CPU to receive the completion.

Retrieve IRQ affinity information using pci_irq_get_affinity() and use
this mapping to choose a reply queue.

[mkp: tweaked commit desc]

Cc: Hannes Reinecke <hare@suse.de>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>,
Cc: James Bottomley <james.bottomley@hansenpartnership.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: Don Brace <don.brace@microsemi.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Meelis Roos <mroos@linux.ee>
Cc: Artem Bityutskiy <artem.bityutskiy@intel.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Fixes: 84676c1f ("genirq/affinity: assign vectors to all possible CPUs")
Signed-off-by: default avatarMing Lei <ming.lei@redhat.com>
Tested-by: default avatarLaurence Oberman <loberman@redhat.com>
Tested-by: default avatarDon Brace <don.brace@microsemi.com>
Tested-by: default avatarArtem Bityutskiy <artem.bityutskiy@intel.com>
Acked-by: default avatarDon Brace <don.brace@microsemi.com>
Reviewed-by: default avatarChristoph Hellwig <hch@lst.de>
Signed-off-by: default avatarMartin K. Petersen <martin.petersen@oracle.com>
parent 14bc1dff
......@@ -1045,11 +1045,7 @@ static void set_performant_mode(struct ctlr_info *h, struct CommandList *c,
c->busaddr |= 1 | (h->blockFetchTable[c->Header.SGList] << 1);
if (unlikely(!h->msix_vectors))
return;
if (likely(reply_queue == DEFAULT_REPLY_QUEUE))
c->Header.ReplyQueue =
raw_smp_processor_id() % h->nreply_queues;
else
c->Header.ReplyQueue = reply_queue % h->nreply_queues;
c->Header.ReplyQueue = reply_queue;
}
}
......@@ -1063,10 +1059,7 @@ static void set_ioaccel1_performant_mode(struct ctlr_info *h,
* Tell the controller to post the reply to the queue for this
* processor. This seems to give the best I/O throughput.
*/
if (likely(reply_queue == DEFAULT_REPLY_QUEUE))
cp->ReplyQueue = smp_processor_id() % h->nreply_queues;
else
cp->ReplyQueue = reply_queue % h->nreply_queues;
cp->ReplyQueue = reply_queue;
/*
* Set the bits in the address sent down to include:
* - performant mode bit (bit 0)
......@@ -1087,10 +1080,7 @@ static void set_ioaccel2_tmf_performant_mode(struct ctlr_info *h,
/* Tell the controller to post the reply to the queue for this
* processor. This seems to give the best I/O throughput.
*/
if (likely(reply_queue == DEFAULT_REPLY_QUEUE))
cp->reply_queue = smp_processor_id() % h->nreply_queues;
else
cp->reply_queue = reply_queue % h->nreply_queues;
cp->reply_queue = reply_queue;
/* Set the bits in the address sent down to include:
* - performant mode bit not used in ioaccel mode 2
* - pull count (bits 0-3)
......@@ -1109,10 +1099,7 @@ static void set_ioaccel2_performant_mode(struct ctlr_info *h,
* Tell the controller to post the reply to the queue for this
* processor. This seems to give the best I/O throughput.
*/
if (likely(reply_queue == DEFAULT_REPLY_QUEUE))
cp->reply_queue = smp_processor_id() % h->nreply_queues;
else
cp->reply_queue = reply_queue % h->nreply_queues;
cp->reply_queue = reply_queue;
/*
* Set the bits in the address sent down to include:
* - performant mode bit not used in ioaccel mode 2
......@@ -1157,6 +1144,8 @@ static void __enqueue_cmd_and_start_io(struct ctlr_info *h,
{
dial_down_lockup_detection_during_fw_flash(h, c);
atomic_inc(&h->commands_outstanding);
reply_queue = h->reply_map[raw_smp_processor_id()];
switch (c->cmd_type) {
case CMD_IOACCEL1:
set_ioaccel1_performant_mode(h, c, reply_queue);
......@@ -7376,6 +7365,26 @@ static void hpsa_disable_interrupt_mode(struct ctlr_info *h)
h->msix_vectors = 0;
}
static void hpsa_setup_reply_map(struct ctlr_info *h)
{
const struct cpumask *mask;
unsigned int queue, cpu;
for (queue = 0; queue < h->msix_vectors; queue++) {
mask = pci_irq_get_affinity(h->pdev, queue);
if (!mask)
goto fallback;
for_each_cpu(cpu, mask)
h->reply_map[cpu] = queue;
}
return;
fallback:
for_each_possible_cpu(cpu)
h->reply_map[cpu] = 0;
}
/* If MSI/MSI-X is supported by the kernel we will try to enable it on
* controllers that are capable. If not, we use legacy INTx mode.
*/
......@@ -7771,6 +7780,10 @@ static int hpsa_pci_init(struct ctlr_info *h)
err = hpsa_interrupt_mode(h);
if (err)
goto clean1;
/* setup mapping between CPU and reply queue */
hpsa_setup_reply_map(h);
err = hpsa_pci_find_memory_BAR(h->pdev, &h->paddr);
if (err)
goto clean2; /* intmode+region, pci */
......@@ -8480,6 +8493,28 @@ static struct workqueue_struct *hpsa_create_controller_wq(struct ctlr_info *h,
return wq;
}
static void hpda_free_ctlr_info(struct ctlr_info *h)
{
kfree(h->reply_map);
kfree(h);
}
static struct ctlr_info *hpda_alloc_ctlr_info(void)
{
struct ctlr_info *h;
h = kzalloc(sizeof(*h), GFP_KERNEL);
if (!h)
return NULL;
h->reply_map = kzalloc(sizeof(*h->reply_map) * nr_cpu_ids, GFP_KERNEL);
if (!h->reply_map) {
kfree(h);
return NULL;
}
return h;
}
static int hpsa_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
{
int dac, rc;
......@@ -8517,7 +8552,7 @@ static int hpsa_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
* the driver. See comments in hpsa.h for more info.
*/
BUILD_BUG_ON(sizeof(struct CommandList) % COMMANDLIST_ALIGNMENT);
h = kzalloc(sizeof(*h), GFP_KERNEL);
h = hpda_alloc_ctlr_info();
if (!h) {
dev_err(&pdev->dev, "Failed to allocate controller head\n");
return -ENOMEM;
......@@ -8916,7 +8951,7 @@ static void hpsa_remove_one(struct pci_dev *pdev)
h->lockup_detected = NULL; /* init_one 2 */
/* (void) pci_disable_pcie_error_reporting(pdev); */ /* init_one 1 */
kfree(h); /* init_one 1 */
hpda_free_ctlr_info(h); /* init_one 1 */
}
static int hpsa_suspend(__attribute__((unused)) struct pci_dev *pdev,
......
......@@ -158,6 +158,7 @@ struct bmic_controller_parameters {
#pragma pack()
struct ctlr_info {
unsigned int *reply_map;
int ctlr;
char devname[8];
char *product_name;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment