Commit 8b9dc8dd authored by Steve Hodgson's avatar Steve Hodgson Committed by David S. Miller

sfc: SFT9001: Fix speed reporting in 1G PHY loopback

Instead of disabling AN in loopback, just prevent restarting AN and
override the speed in sft9001_get_settings().
Signed-off-by: default avatarBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 2d18835d
......@@ -15,6 +15,7 @@
#include "net_driver.h"
#include "mdio_10g.h"
#include "boards.h"
#include "workarounds.h"
int mdio_clause45_reset_mmd(struct efx_nic *port, int mmd,
int spins, int spintime)
......@@ -517,6 +518,9 @@ int mdio_clause45_set_settings(struct efx_nic *efx,
reg |= BMCR_ANENABLE | BMCR_ANRESTART;
else
reg &= ~BMCR_ANENABLE;
if (EFX_WORKAROUND_15195(efx)
&& LOOPBACK_MASK(efx) & efx->phy_op->loopbacks)
reg &= ~BMCR_ANRESTART;
if (xnp)
reg |= 1 << MDIO_AN_CTRL_XNP_LBN;
else
......
......@@ -511,7 +511,7 @@ static void tenxpress_phy_reconfigure(struct efx_nic *efx)
{
struct tenxpress_phy_data *phy_data = efx->phy_data;
struct ethtool_cmd ecmd;
bool phy_mode_change, loop_reset, loop_toggle, loopback;
bool phy_mode_change, loop_reset;
if (efx->phy_mode & (PHY_MODE_OFF | PHY_MODE_SPECIAL)) {
phy_data->phy_mode = efx->phy_mode;
......@@ -522,12 +522,10 @@ static void tenxpress_phy_reconfigure(struct efx_nic *efx)
phy_mode_change = (efx->phy_mode == PHY_MODE_NORMAL &&
phy_data->phy_mode != PHY_MODE_NORMAL);
loopback = LOOPBACK_MASK(efx) & efx->phy_op->loopbacks;
loop_toggle = LOOPBACK_CHANGED(phy_data, efx, efx->phy_op->loopbacks);
loop_reset = (LOOPBACK_OUT_OF(phy_data, efx, efx->phy_op->loopbacks) ||
LOOPBACK_CHANGED(phy_data, efx, 1 << LOOPBACK_GPHY));
if (loop_reset || loop_toggle || loopback || phy_mode_change) {
if (loop_reset || phy_mode_change) {
int rc;
efx->phy_op->get_settings(efx, &ecmd);
......@@ -542,20 +540,6 @@ static void tenxpress_phy_reconfigure(struct efx_nic *efx)
falcon_reset_xaui(efx);
}
if (efx->phy_type != PHY_TYPE_SFX7101) {
/* Only change autoneg once, on coming out or
* going into loopback */
if (loop_toggle)
ecmd.autoneg = !loopback;
if (loopback) {
ecmd.duplex = DUPLEX_FULL;
if (efx->loopback_mode == LOOPBACK_GPHY)
ecmd.speed = SPEED_1000;
else
ecmd.speed = SPEED_10000;
}
}
rc = efx->phy_op->set_settings(efx, &ecmd);
WARN_ON(rc);
}
......@@ -813,6 +797,13 @@ static void sft9001_get_settings(struct efx_nic *efx, struct ethtool_cmd *ecmd)
ecmd->duplex = (reg & (1 << GPHY_DUPLEX_LBN) ?
DUPLEX_FULL : DUPLEX_HALF);
}
/* In loopback, the PHY automatically brings up the correct interface,
* but doesn't advertise the correct speed. So override it */
if (efx->loopback_mode == LOOPBACK_GPHY)
ecmd->speed = SPEED_1000;
else if (LOOPBACK_MASK(efx) & SFT9001_LOOPBACKS)
ecmd->speed = SPEED_10000;
}
static int sft9001_set_settings(struct efx_nic *efx, struct ethtool_cmd *ecmd)
......
......@@ -19,6 +19,8 @@
#define EFX_WORKAROUND_FALCON_A(efx) (falcon_rev(efx) <= FALCON_REV_A1)
#define EFX_WORKAROUND_10G(efx) EFX_IS10G(efx)
#define EFX_WORKAROUND_SFT9001A(efx) ((efx)->phy_type == PHY_TYPE_SFT9001A)
#define EFX_WORKAROUND_SFT9001(efx) ((efx)->phy_type == PHY_TYPE_SFT9001A || \
(efx)->phy_type == PHY_TYPE_SFT9001B)
/* XAUI resets if link not detected */
#define EFX_WORKAROUND_5147 EFX_WORKAROUND_ALWAYS
......@@ -56,4 +58,7 @@
/* Need to keep AN enabled */
#define EFX_WORKAROUND_13963 EFX_WORKAROUND_SFT9001A
/* Don't restart AN in near-side loopback */
#define EFX_WORKAROUND_15195 EFX_WORKAROUND_SFT9001
#endif /* EFX_WORKAROUNDS_H */
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment