pinctrl: Adds slew-rate, input-enable/disable

This commit adds slew-rate and input-enable/disable support for pinconf
-generic.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt

@@ -151,6 +151,8 @@ drive-push-pull		- drive actively high and low
 drive-open-drain	- drive with open drain
 drive-open-source	- drive with open source
 drive-strength		- sink or source at most X mA
+input-enable		- enable input on pin (no effect on output)
+input-disable		- disable input on pin (no effect on output)
 input-schmitt-enable	- enable schmitt-trigger mode
 input-schmitt-disable	- disable schmitt-trigger mode
 input-debounce		- debounce mode with debound time X
@@ -158,6 +160,7 @@ low-power-enable	- enable low power mode
 low-power-disable	- disable low power mode
 output-low		- set the pin to output mode with low level
 output-high		- set the pin to output mode with high level
+slew-rate		- set the slew rate
 
 Some of the generic properties take arguments. For those that do, the
 arguments are described below.

drivers/pinctrl/pinconf-generic.c

@@ -48,6 +48,7 @@ static struct pin_config_item conf_items[] = {
 	PCONFDUMP(PIN_CONFIG_DRIVE_OPEN_DRAIN, "output drive open drain", NULL),
 	PCONFDUMP(PIN_CONFIG_DRIVE_OPEN_SOURCE, "output drive open source", NULL),
 	PCONFDUMP(PIN_CONFIG_DRIVE_STRENGTH, "output drive strength", "mA"),
+	PCONFDUMP(PIN_CONFIG_INPUT_ENABLE, "input enabled", NULL),
 	PCONFDUMP(PIN_CONFIG_INPUT_SCHMITT_ENABLE, "input schmitt enabled", NULL),
 	PCONFDUMP(PIN_CONFIG_INPUT_SCHMITT, "input schmitt trigger", NULL),
 	PCONFDUMP(PIN_CONFIG_INPUT_DEBOUNCE, "input debounce", "usec"),
@@ -160,6 +161,8 @@ static struct pinconf_generic_dt_params dt_params[] = {
 	{ "drive-open-drain", PIN_CONFIG_DRIVE_OPEN_DRAIN, 0 },
 	{ "drive-open-source", PIN_CONFIG_DRIVE_OPEN_SOURCE, 0 },
 	{ "drive-strength", PIN_CONFIG_DRIVE_STRENGTH, 0 },
+	{ "input-enable", PIN_CONFIG_INPUT_ENABLE, 1 },
+	{ "input-disable", PIN_CONFIG_INPUT_ENABLE, 0 },
 	{ "input-schmitt-enable", PIN_CONFIG_INPUT_SCHMITT_ENABLE, 1 },
 	{ "input-schmitt-disable", PIN_CONFIG_INPUT_SCHMITT_ENABLE, 0 },
 	{ "input-debounce", PIN_CONFIG_INPUT_DEBOUNCE, 0 },
@@ -167,6 +170,7 @@ static struct pinconf_generic_dt_params dt_params[] = {
 	{ "low-power-disable", PIN_CONFIG_LOW_POWER_MODE, 0 },
 	{ "output-low", PIN_CONFIG_OUTPUT, 0, },
 	{ "output-high", PIN_CONFIG_OUTPUT, 1, },
+	{ "slew-rate", PIN_CONFIG_SLEW_RATE, 0},
 };
 
 /**

include/linux/pinctrl/pinconf-generic.h

@@ -61,6 +61,9 @@
  *	argument is ignored.
  * @PIN_CONFIG_DRIVE_STRENGTH: the pin will sink or source at most the current
  *	passed as argument. The argument is in mA.
+ * @PIN_CONFIG_INPUT_ENABLE: enable the pin's input.  Note that this does not
+ *	affect the pin's ability to drive output.  1 enables input, 0 disables
+ *	input.
  * @PIN_CONFIG_INPUT_SCHMITT_ENABLE: control schmitt-trigger mode on the pin.
  *      If the argument != 0, schmitt-trigger mode is enabled. If it's 0,
  *      schmitt-trigger mode is disabled.
@@ -101,6 +104,7 @@ enum pin_config_param {
 	PIN_CONFIG_DRIVE_OPEN_DRAIN,
 	PIN_CONFIG_DRIVE_OPEN_SOURCE,
 	PIN_CONFIG_DRIVE_STRENGTH,
+	PIN_CONFIG_INPUT_ENABLE,
 	PIN_CONFIG_INPUT_SCHMITT_ENABLE,
 	PIN_CONFIG_INPUT_SCHMITT,
 	PIN_CONFIG_INPUT_DEBOUNCE,