Commit 8bdc8939 authored by Jacek Anaszewski's avatar Jacek Anaszewski Committed by Bryan Wu

DT: aat1290: Document handling external strobe sources

This patch adds documentation for a pinctrl-names property.
The property, when present, is used for switching the source
of the strobe signal for the device.
Signed-off-by: default avatarJacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: default avatarKyungmin Park <kyungmin.park@samsung.com>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: devicetree@vger.kernel.org
Acked-by: default avatarSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: default avatarBryan Wu <cooloney@gmail.com>
parent 0b380186
...@@ -2,7 +2,9 @@ ...@@ -2,7 +2,9 @@
The device is controlled through two pins: FL_EN and EN_SET. The pins when, The device is controlled through two pins: FL_EN and EN_SET. The pins when,
asserted high, enable flash strobe and movie mode (max 1/2 of flash current) asserted high, enable flash strobe and movie mode (max 1/2 of flash current)
respectively. respectively. In order to add a capability of selecting the strobe signal source
(e.g. CPU or camera sensor) there is an additional switch required, independent
of the flash chip. The switch is controlled with pin control.
Required properties: Required properties:
...@@ -10,6 +12,13 @@ Required properties: ...@@ -10,6 +12,13 @@ Required properties:
- flen-gpios : Must be device tree identifier of the flash device FL_EN pin. - flen-gpios : Must be device tree identifier of the flash device FL_EN pin.
- enset-gpios : Must be device tree identifier of the flash device EN_SET pin. - enset-gpios : Must be device tree identifier of the flash device EN_SET pin.
Optional properties:
- pinctrl-names : Must contain entries: "default", "host", "isp". Entries
"default" and "host" must refer to the same pin configuration
node, which sets the host as a strobe signal provider. Entry
"isp" must refer to the pin configuration node, which sets the
ISP as a strobe signal provider.
A discrete LED element connected to the device must be represented by a child A discrete LED element connected to the device must be represented by a child
node - see Documentation/devicetree/bindings/leds/common.txt. node - see Documentation/devicetree/bindings/leds/common.txt.
...@@ -25,13 +34,22 @@ Required properties of the LED child node: ...@@ -25,13 +34,22 @@ Required properties of the LED child node:
Optional properties of the LED child node: Optional properties of the LED child node:
- label : see Documentation/devicetree/bindings/leds/common.txt - label : see Documentation/devicetree/bindings/leds/common.txt
Example (by Ct = 220nF, Rset = 160kohm): Example (by Ct = 220nF, Rset = 160kohm and exynos4412-trats2 board with
a switch that allows for routing strobe signal either from the host or from
the camera sensor):
#include "exynos4412.dtsi"
aat1290 { aat1290 {
compatible = "skyworks,aat1290"; compatible = "skyworks,aat1290";
flen-gpios = <&gpj1 1 GPIO_ACTIVE_HIGH>; flen-gpios = <&gpj1 1 GPIO_ACTIVE_HIGH>;
enset-gpios = <&gpj1 2 GPIO_ACTIVE_HIGH>; enset-gpios = <&gpj1 2 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default", "host", "isp";
pinctrl-0 = <&camera_flash_host>;
pinctrl-1 = <&camera_flash_host>;
pinctrl-2 = <&camera_flash_isp>;
camera_flash: flash-led { camera_flash: flash-led {
label = "aat1290-flash"; label = "aat1290-flash";
led-max-microamp = <520833>; led-max-microamp = <520833>;
...@@ -39,3 +57,17 @@ aat1290 { ...@@ -39,3 +57,17 @@ aat1290 {
flash-timeout-us = <1940000>; flash-timeout-us = <1940000>;
}; };
}; };
&pinctrl_0 {
camera_flash_host: camera-flash-host {
samsung,pins = "gpj1-0";
samsung,pin-function = <1>;
samsung,pin-val = <0>;
};
camera_flash_isp: camera-flash-isp {
samsung,pins = "gpj1-0";
samsung,pin-function = <1>;
samsung,pin-val = <1>;
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment