Merge branch 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6

* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: clkfwk: Fix up checkpatch warnings.
  sh: make some needlessly global sh7724 clocks static
  sh: add clk_round_parent() to optimize parent clock rate
  sh: Simplify phys_addr_mask()/PTE_PHYS_MASK for 29/32-bit.
  sh: nommu: Support building without an uncached mapping.
  sh: nommu: use 32-bit phys mode.
  sh: mach-se: Fix up SE7206 no ioport build.
  sh: intc: Update for single IRQ reservation helper.
  sh: clkfwk: Fix up rate rounding error handling.
  sh: mach-se: Rip out superfluous 7751 PIO routines.
  sh: mach-se: Rip out superfluous 770x PIO routines.
  sh: mach-edosk7705: Kill off machtype, consolidate board def.
  sh: mach-edosk7705: update for this century, kill off PIO trapping.
  sh: mach-se: Rip out superfluous 7206 PIO routines.
  sh: mach-systemh: Kill off dead board.
  sh: mach-snapgear: Kill off machtype, consolidate board def.
  sh: mach-snapgear: Rip out superfluous PIO routines.
  sh: mach-microdev: SuperIO-relative ioport mapping.

arch/sh/Kconfig

@@ -193,6 +193,7 @@ config CPU_SH2
 config CPU_SH2A
 	bool
 	select CPU_SH2
+	select UNCACHED_MAPPING
 
 config CPU_SH3
 	bool

arch/sh/Makefile

@@ -133,10 +133,7 @@ machdir-$(CONFIG_SOLUTION_ENGINE)		+= mach-se
 machdir-$(CONFIG_SH_HP6XX)			+= mach-hp6xx
 machdir-$(CONFIG_SH_DREAMCAST)			+= mach-dreamcast
 machdir-$(CONFIG_SH_SH03)			+= mach-sh03
-machdir-$(CONFIG_SH_SECUREEDGE5410)		+= mach-snapgear
 machdir-$(CONFIG_SH_RTS7751R2D)			+= mach-r2d
-machdir-$(CONFIG_SH_7751_SYSTEMH)		+= mach-systemh
-machdir-$(CONFIG_SH_EDOSK7705)			+= mach-edosk7705
 machdir-$(CONFIG_SH_HIGHLANDER)			+= mach-highlander
 machdir-$(CONFIG_SH_MIGOR)			+= mach-migor
 machdir-$(CONFIG_SH_AP325RXA)			+= mach-ap325rxa

arch/sh/boards/Kconfig

@@ -81,13 +81,6 @@ config SH_7343_SOLUTION_ENGINE
 	  Select 7343 SolutionEngine if configuring for a Hitachi
 	  SH7343 (SH-Mobile 3AS) evaluation board.
 
-config SH_7751_SYSTEMH
-	bool "SystemH7751R"
-	depends on CPU_SUBTYPE_SH7751R
-	help
-	  Select SystemH if you are configuring for a Renesas SystemH
-	  7751R evaluation board.
-
 config SH_HP6XX
 	bool "HP6XX"
 	select SYS_SUPPORTS_APM_EMULATION

arch/sh/boards/Makefile

@@ -2,10 +2,12 @@
 # Specific board support, not covered by a mach group.
 #
 obj-$(CONFIG_SH_MAGIC_PANEL_R2)	+= board-magicpanelr2.o
+obj-$(CONFIG_SH_SECUREEDGE5410)	+= board-secureedge5410.o
 obj-$(CONFIG_SH_SH2007)		+= board-sh2007.o
 obj-$(CONFIG_SH_SH7785LCR)	+= board-sh7785lcr.o
 obj-$(CONFIG_SH_URQUELL)	+= board-urquell.o
 obj-$(CONFIG_SH_SHMIN)		+= board-shmin.o
+obj-$(CONFIG_SH_EDOSK7705)	+= board-edosk7705.o
 obj-$(CONFIG_SH_EDOSK7760)	+= board-edosk7760.o
 obj-$(CONFIG_SH_ESPT)		+= board-espt.o
 obj-$(CONFIG_SH_POLARIS)	+= board-polaris.o

arch/sh/boards/mach-edosk7705/setup.c → arch/sh/boards/board-edosk7705.c

@@ -10,27 +10,69 @@
  */
 #include <linux/init.h>
 #include <linux/irq.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/smc91x.h>
 #include <asm/machvec.h>
-#include <mach/edosk7705.h>
+#include <asm/sizes.h>
+
+#define SMC_IOBASE	0xA2000000
+#define SMC_IO_OFFSET	0x300
+#define SMC_IOADDR	(SMC_IOBASE + SMC_IO_OFFSET)
+
+#define ETHERNET_IRQ	0x09
 
 static void __init sh_edosk7705_init_irq(void)
 {
-	/* This is the Ethernet interrupt */
-	make_imask_irq(0x09);
+	make_imask_irq(ETHERNET_IRQ);
 }
 
+/* eth initialization functions */
+static struct smc91x_platdata smc91x_info = {
+	.flags = SMC91X_USE_16BIT | SMC91X_IO_SHIFT_1 | IORESOURCE_IRQ_LOWLEVEL,
+};
+
+static struct resource smc91x_res[] = {
+	[0] = {
+		.start	= SMC_IOADDR,
+		.end	= SMC_IOADDR + SZ_32 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= ETHERNET_IRQ,
+		.end	= ETHERNET_IRQ,
+		.flags	= IORESOURCE_IRQ ,
+	}
+};
+
+static struct platform_device smc91x_dev = {
+	.name		= "smc91x",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(smc91x_res),
+	.resource	= smc91x_res,
+
+	.dev	= {
+		.platform_data	= &smc91x_info,
+	},
+};
+
+/* platform init code */
+static struct platform_device *edosk7705_devices[] __initdata = {
+	&smc91x_dev,
+};
+
+static int __init init_edosk7705_devices(void)
+{
+	return platform_add_devices(edosk7705_devices,
+				    ARRAY_SIZE(edosk7705_devices));
+}
+__initcall(init_edosk7705_devices);
+
 /*
  * The Machine Vector
  */
 static struct sh_machine_vector mv_edosk7705 __initmv = {
 	.mv_name		= "EDOSK7705",
 	.mv_nr_irqs		= 80,
-
-	.mv_inb			= sh_edosk7705_inb,
-	.mv_outb		= sh_edosk7705_outb,
-
-	.mv_insb		= sh_edosk7705_insb,
-	.mv_outsb		= sh_edosk7705_outsb,
-
 	.mv_init_irq		= sh_edosk7705_init_irq,
 };

arch/sh/boards/mach-snapgear/setup.c → arch/sh/boards/board-secureedge5410.c

 /*
- * linux/arch/sh/boards/snapgear/setup.c
- *
  * Copyright (C) 2002  David McCullough <davidm@snapgear.com>
  * Copyright (C) 2003  Paul Mundt <lethal@linux-sh.org>
  *
@@ -19,18 +17,19 @@
 #include <linux/module.h>
 #include <linux/sched.h>
 #include <asm/machvec.h>
-#include <mach/snapgear.h>
+#include <mach/secureedge5410.h>
 #include <asm/irq.h>
 #include <asm/io.h>
 #include <cpu/timer.h>
 
+unsigned short secureedge5410_ioport;
+
 /*
  * EraseConfig handling functions
  */
-
 static irqreturn_t eraseconfig_interrupt(int irq, void *dev_id)
 {
-	(void)__raw_readb(0xb8000000);	/* dummy read */
+	ctrl_delay();	/* dummy read */
 
 	printk("SnapGear: erase switch interrupt!\n");
 
@@ -39,21 +38,22 @@ static irqreturn_t eraseconfig_interrupt(int irq, void *dev_id)
 
 static int __init eraseconfig_init(void)
 {
+	unsigned int irq = evt2irq(0x240);
+
 	printk("SnapGear: EraseConfig init\n");
+
 	/* Setup "EraseConfig" switch on external IRQ 0 */
-	if (request_irq(IRL0_IRQ, eraseconfig_interrupt, IRQF_DISABLED,
+	if (request_irq(irq, eraseconfig_interrupt, IRQF_DISABLED,
 				"Erase Config", NULL))
 		printk("SnapGear: failed to register IRQ%d for Reset witch\n",
-				IRL0_IRQ);
+				irq);
 	else
 		printk("SnapGear: registered EraseConfig switch on IRQ%d\n",
-				IRL0_IRQ);
-	return(0);
+				irq);
+	return 0;
 }
-
 module_init(eraseconfig_init);
 
-/****************************************************************************/
 /*
  * Initialize IRQ setting
  *
@@ -62,7 +62,6 @@ module_init(eraseconfig_init);
  * IRL2 = eth1
  * IRL3 = crypto
  */
-
 static void __init init_snapgear_IRQ(void)
 {
 	printk("Setup SnapGear IRQ/IPR ...\n");
@@ -76,20 +75,5 @@ static void __init init_snapgear_IRQ(void)
 static struct sh_machine_vector mv_snapgear __initmv = {
 	.mv_name		= "SnapGear SecureEdge5410",
 	.mv_nr_irqs		= 72,
-
-	.mv_inb			= snapgear_inb,
-	.mv_inw			= snapgear_inw,
-	.mv_inl			= snapgear_inl,
-	.mv_outb		= snapgear_outb,
-	.mv_outw		= snapgear_outw,
-	.mv_outl		= snapgear_outl,
-
-	.mv_inb_p		= snapgear_inb_p,
-	.mv_inw_p		= snapgear_inw,
-	.mv_inl_p		= snapgear_inl,
-	.mv_outb_p		= snapgear_outb_p,
-	.mv_outw_p		= snapgear_outw,
-	.mv_outl_p		= snapgear_outl,
-
 	.mv_init_irq		= init_snapgear_IRQ,
 };

arch/sh/boards/mach-edosk7705/Makefile

-#
-# Makefile for the EDOSK7705 specific parts of the kernel
-#
-
-obj-y	 := setup.o io.o

arch/sh/boards/mach-edosk7705/io.c

-/*
- * arch/sh/boards/renesas/edosk7705/io.c
- *
- * Copyright (C) 2001  Ian da Silva, Jeremy Siegel
- * Based largely on io_se.c.
- *
- * I/O routines for Hitachi EDOSK7705 board.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/io.h>
-#include <mach/edosk7705.h>
-#include <asm/addrspace.h>
-
-#define SMC_IOADDR	0xA2000000
-
-/* Map the Ethernet addresses as if it is at 0x300 - 0x320 */
-static unsigned long sh_edosk7705_isa_port2addr(unsigned long port)
-{
-	/*
-	 * SMC91C96 registers are 4 byte aligned rather than the
-	 * usual 2 byte!
-	 */
-	if (port >= 0x300 && port < 0x320)
-		return SMC_IOADDR + ((port - 0x300) * 2);
-
-	maybebadio(port);
-	return port;
-}
-
-/* Trying to read / write bytes on odd-byte boundaries to the Ethernet
- * registers causes problems. So we bit-shift the value and read / write
- * in 2 byte chunks. Setting the low byte to 0 does not cause problems
- * now as odd byte writes are only made on the bit mask / interrupt
- * register. This may not be the case in future Mar-2003 SJD
- */
-unsigned char sh_edosk7705_inb(unsigned long port)
-{
-	if (port >= 0x300 && port < 0x320 && port & 0x01)
-		return __raw_readw(port - 1) >> 8;
-
-	return __raw_readb(sh_edosk7705_isa_port2addr(port));
-}
-
-void sh_edosk7705_outb(unsigned char value, unsigned long port)
-{
-	if (port >= 0x300 && port < 0x320 && port & 0x01) {
-		__raw_writew(((unsigned short)value << 8), port - 1);
-		return;
-	}
-
-	__raw_writeb(value, sh_edosk7705_isa_port2addr(port));
-}
-
-void sh_edosk7705_insb(unsigned long port, void *addr, unsigned long count)
-{
-	unsigned char *p = addr;
-
-	while (count--)
-		*p++ = sh_edosk7705_inb(port);
-}
-
-void sh_edosk7705_outsb(unsigned long port, const void *addr, unsigned long count)
-{
-	unsigned char *p = (unsigned char *)addr;
-
-	while (count--)
-		sh_edosk7705_outb(*p++, port);
-}

arch/sh/boards/mach-microdev/io.c

@@ -54,7 +54,7 @@
 /*
  * map I/O ports to memory-mapped addresses
  */
-static unsigned long microdev_isa_port2addr(unsigned long offset)
+void __iomem *microdev_ioport_map(unsigned long offset, unsigned int len)
 {
 	unsigned long result;
 
@@ -72,16 +72,6 @@ static unsigned long microdev_isa_port2addr(unsigned long offset)
 			 *	Configuration Registers
 			 */
 		result = IO_SUPERIO_PHYS + (offset << 1);
-#if 0
-	} else if (offset == KBD_DATA_REG || offset == KBD_CNTL_REG ||
-		   offset == KBD_STATUS_REG) {
-			/*
-			 *	SMSC FDC37C93xAPM SuperIO chip
-			 *
-			 *	PS/2 Keyboard + Mouse (ports 0x60 and 0x64).
-			 */
-	        result = IO_SUPERIO_PHYS + (offset << 1);
-#endif
 	} else if (((offset >= IO_IDE1_BASE) &&
 		    (offset <  IO_IDE1_BASE + IO_IDE_EXTENT)) ||
 		    (offset == IO_IDE1_MISC)) {
@@ -131,237 +121,5 @@ static unsigned long microdev_isa_port2addr(unsigned long offset)
 		result = PVR;
 	}
 
-	return result;
-}
-
-#define PORT2ADDR(x) (microdev_isa_port2addr(x))
-
-static inline void delay(void)
-{
-#if defined(CONFIG_PCI)
-	/* System board present, just make a dummy SRAM access.  (CS0 will be
-	   mapped to PCI memory, probably good to avoid it.) */
-	__raw_readw(0xa6800000);
-#else
-	/* CS0 will be mapped to flash, ROM etc so safe to access it. */
-	__raw_readw(0xa0000000);
-#endif
-}
-
-unsigned char microdev_inb(unsigned long port)
-{
-#ifdef CONFIG_PCI
-	if (port >= PCIBIOS_MIN_IO)
-		return microdev_pci_inb(port);
-#endif
-	return *(volatile unsigned char*)PORT2ADDR(port);
-}
-
-unsigned short microdev_inw(unsigned long port)
-{
-#ifdef CONFIG_PCI
-	if (port >= PCIBIOS_MIN_IO)
-		return microdev_pci_inw(port);
-#endif
-	return *(volatile unsigned short*)PORT2ADDR(port);
-}
-
-unsigned int microdev_inl(unsigned long port)
-{
-#ifdef CONFIG_PCI
-	if (port >= PCIBIOS_MIN_IO)
-		return microdev_pci_inl(port);
-#endif
-	return *(volatile unsigned int*)PORT2ADDR(port);
-}
-
-void microdev_outw(unsigned short b, unsigned long port)
-{
-#ifdef CONFIG_PCI
-	if (port >= PCIBIOS_MIN_IO) {
-		microdev_pci_outw(b, port);
-		return;
-	}
-#endif
-	*(volatile unsigned short*)PORT2ADDR(port) = b;
-}
-
-void microdev_outb(unsigned char b, unsigned long port)
-{
-#ifdef CONFIG_PCI
-	if (port >= PCIBIOS_MIN_IO) {
-		microdev_pci_outb(b, port);
-		return;
-	}
-#endif
-
-	/*
-	 *	There is a board feature with the current SH4-202 MicroDev in
-	 *	that the 2 byte enables (nBE0 and nBE1) are tied together (and
-	 *	to the Chip Select Line (Ethernet_CS)). Due to this connectivity,
-	 *	it is not possible to safely perform 8-bit writes to the
-	 *	Ethernet registers, as 16-bits will be consumed from the Data
-	 *	lines (corrupting the other byte).  Hence, this function is
-	 *	written to implement 16-bit read/modify/write for all byte-wide
-	 *	accesses.
-	 *
-	 *	Note: there is no problem with byte READS (even or odd).
-	 *
-	 *			Sean McGoogan - 16th June 2003.
-	 */
-	if ((port >= IO_LAN91C111_BASE) &&
-	    (port <  IO_LAN91C111_BASE + IO_LAN91C111_EXTENT)) {
-			/*
-			 * Then are trying to perform a byte-write to the
-			 * LAN91C111.  This needs special care.
-			 */
-		if (port % 2 == 1) {	/* is the port odd ? */
-			/* unset bit-0, i.e. make even */
-			const unsigned long evenPort = port-1;
-			unsigned short word;
-
-			/*
-			 * do a 16-bit read/write to write to 'port',
-			 * preserving even byte.
-			 *
-			 *	Even addresses are bits 0-7
-			 *	Odd  addresses are bits 8-15
-			 */
-			word = microdev_inw(evenPort);
-			word = (word & 0xffu) | (b << 8);
-			microdev_outw(word, evenPort);
-		} else {
-			/* else, we are trying to do an even byte write */
-			unsigned short word;
-
-			/*
-			 * do a 16-bit read/write to write to 'port',
-			 * preserving odd byte.
-			 *
-			 *	Even addresses are bits 0-7
-			 *	Odd  addresses are bits 8-15
-			 */
-			word = microdev_inw(port);
-			word = (word & 0xff00u) | (b);
-			microdev_outw(word, port);
-		}
-	} else {
-		*(volatile unsigned char*)PORT2ADDR(port) = b;
-	}
-}
-
-void microdev_outl(unsigned int b, unsigned long port)
-{
-#ifdef CONFIG_PCI
-	if (port >= PCIBIOS_MIN_IO) {
-		microdev_pci_outl(b, port);
-		return;
-	}
-#endif
-	*(volatile unsigned int*)PORT2ADDR(port) = b;
-}
-
-unsigned char microdev_inb_p(unsigned long port)
-{
-	unsigned char v = microdev_inb(port);
-	delay();
-	return v;
-}
-
-unsigned short microdev_inw_p(unsigned long port)
-{
-	unsigned short v = microdev_inw(port);
-	delay();
-	return v;
-}
-
-unsigned int microdev_inl_p(unsigned long port)
-{
-	unsigned int v = microdev_inl(port);
-	delay();
-	return v;
-}
-
-void microdev_outb_p(unsigned char b, unsigned long port)
-{
-	microdev_outb(b, port);
-	delay();
-}
-
-void microdev_outw_p(unsigned short b, unsigned long port)
-{
-	microdev_outw(b, port);
-	delay();
-}
-
-void microdev_outl_p(unsigned int b, unsigned long port)
-{
-	microdev_outl(b, port);
-	delay();
-}
-
-void microdev_insb(unsigned long port, void *buffer, unsigned long count)
-{
-	volatile unsigned char *port_addr;
-	unsigned char *buf = buffer;
-
-	port_addr = (volatile unsigned char *)PORT2ADDR(port);
-
-	while (count--)
-		*buf++ = *port_addr;
-}
-
-void microdev_insw(unsigned long port, void *buffer, unsigned long count)
-{
-	volatile unsigned short *port_addr;
-	unsigned short *buf = buffer;
-
-	port_addr = (volatile unsigned short *)PORT2ADDR(port);
-
-	while (count--)
-		*buf++ = *port_addr;
-}
-
-void microdev_insl(unsigned long port, void *buffer, unsigned long count)
-{
-	volatile unsigned long *port_addr;
-	unsigned int *buf = buffer;
-
-	port_addr = (volatile unsigned long *)PORT2ADDR(port);
-
-	while (count--)
-		*buf++ = *port_addr;
-}
-
-void microdev_outsb(unsigned long port, const void *buffer, unsigned long count)
-{
-	volatile unsigned char *port_addr;
-	const unsigned char *buf = buffer;
-
-	port_addr = (volatile unsigned char *)PORT2ADDR(port);
-
-	while (count--)
-		*port_addr = *buf++;
-}
-
-void microdev_outsw(unsigned long port, const void *buffer, unsigned long count)
-{
-	volatile unsigned short *port_addr;
-	const unsigned short *buf = buffer;
-
-	port_addr = (volatile unsigned short *)PORT2ADDR(port);
-
-	while (count--)
-		*port_addr = *buf++;
-}
-
-void microdev_outsl(unsigned long port, const void *buffer, unsigned long count)
-{
-	volatile unsigned long *port_addr;
-	const unsigned int *buf = buffer;
-
-	port_addr = (volatile unsigned long *)PORT2ADDR(port);
-
-	while (count--)
-		*port_addr = *buf++;
+	return (void __iomem *)result;
 }

arch/sh/boards/mach-microdev/setup.c

@@ -195,27 +195,6 @@ device_initcall(microdev_devices_setup);
 static struct sh_machine_vector mv_sh4202_microdev __initmv = {
 	.mv_name		= "SH4-202 MicroDev",
 	.mv_nr_irqs		= 72,
-
-	.mv_inb			= microdev_inb,
-	.mv_inw			= microdev_inw,
-	.mv_inl			= microdev_inl,
-	.mv_outb		= microdev_outb,
-	.mv_outw		= microdev_outw,
-	.mv_outl		= microdev_outl,
-
-	.mv_inb_p		= microdev_inb_p,
-	.mv_inw_p		= microdev_inw_p,
-	.mv_inl_p		= microdev_inl_p,
-	.mv_outb_p		= microdev_outb_p,
-	.mv_outw_p		= microdev_outw_p,
-	.mv_outl_p		= microdev_outl_p,
-
-	.mv_insb		= microdev_insb,
-	.mv_insw		= microdev_insw,
-	.mv_insl		= microdev_insl,
-	.mv_outsb		= microdev_outsb,
-	.mv_outsw		= microdev_outsw,
-	.mv_outsl		= microdev_outsl,
-
+	.mv_ioport_map		= microdev_ioport_map,
 	.mv_init_irq		= init_microdev_irq,
 };

arch/sh/boards/mach-se/7206/Makefile

@@ -2,4 +2,4 @@
 # Makefile for the 7206 SolutionEngine specific parts of the kernel
 #
 
-obj-y	 := setup.o io.o irq.o
+obj-y	 := setup.o irq.o

arch/sh/boards/mach-se/7206/io.c

-/* $Id: io.c,v 1.5 2004/02/22 23:08:43 kkojima Exp $
- *
- * linux/arch/sh/boards/se/7206/io.c
- *
- * Copyright (C) 2006 Yoshinori Sato
- *
- * I/O routine for Hitachi 7206 SolutionEngine.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <asm/io.h>
-#include <mach-se/mach/se7206.h>
-
-
-static inline void delay(void)
-{
-	__raw_readw(0x20000000);  /* P2 ROM Area */
-}
-
-/* MS7750 requires special versions of in*, out* routines, since
-   PC-like io ports are located at upper half byte of 16-bit word which
-   can be accessed only with 16-bit wide.  */
-
-static inline volatile __u16 *
-port2adr(unsigned int port)
-{
-	if (port >= 0x2000 && port < 0x2020)
-		return (volatile __u16 *) (PA_MRSHPC + (port - 0x2000));
-	else if (port >= 0x300 && port < 0x310)
-		return (volatile __u16 *) (PA_SMSC + (port - 0x300));
-
-	return (volatile __u16 *)port;
-}
-
-unsigned char se7206_inb(unsigned long port)
-{
-	return (*port2adr(port)) & 0xff;
-}
-
-unsigned char se7206_inb_p(unsigned long port)
-{
-	unsigned long v;
-
-	v = (*port2adr(port)) & 0xff;
-	delay();
-	return v;
-}
-
-unsigned short se7206_inw(unsigned long port)
-{
-	return *port2adr(port);
-}
-
-void se7206_outb(unsigned char value, unsigned long port)
-{
-	*(port2adr(port)) = value;
-}
-
-void se7206_outb_p(unsigned char value, unsigned long port)
-{
-	*(port2adr(port)) = value;
-	delay();
-}
-
-void se7206_outw(unsigned short value, unsigned long port)
-{
-	*port2adr(port) = value;
-}
-
-void se7206_insb(unsigned long port, void *addr, unsigned long count)
-{
-	volatile __u16 *p = port2adr(port);
-	__u8 *ap = addr;
-
-	while (count--)
-		*ap++ = *p;
-}
-
-void se7206_insw(unsigned long port, void *addr, unsigned long count)
-{
-	volatile __u16 *p = port2adr(port);
-	__u16 *ap = addr;
-	while (count--)
-		*ap++ = *p;
-}
-
-void se7206_outsb(unsigned long port, const void *addr, unsigned long count)
-{
-	volatile __u16 *p = port2adr(port);
-	const __u8 *ap = addr;
-
-	while (count--)
-		*p = *ap++;
-}
-
-void se7206_outsw(unsigned long port, const void *addr, unsigned long count)
-{
-	volatile __u16 *p = port2adr(port);
-	const __u16 *ap = addr;
-	while (count--)
-		*p = *ap++;
-}

arch/sh/boards/mach-se/7206/irq.c

@@ -139,11 +139,13 @@ void __init init_se7206_IRQ(void)
 	make_se7206_irq(IRQ0_IRQ); /* SMC91C111 */
 	make_se7206_irq(IRQ1_IRQ); /* ATA */
 	make_se7206_irq(IRQ3_IRQ); /* SLOT / PCM */
-	__raw_writew(inw(INTC_ICR1) | 0x000b ,INTC_ICR1 ) ; /* ICR1 */
+
+	__raw_writew(__raw_readw(INTC_ICR1) | 0x000b, INTC_ICR); /* ICR1 */
 
 	/* FPGA System register setup*/
 	__raw_writew(0x0000,INTSTS0); /* Clear INTSTS0 */
 	__raw_writew(0x0000,INTSTS1); /* Clear INTSTS1 */
+
 	/* IRQ0=LAN, IRQ1=ATA, IRQ3=SLT,PCM */
 	__raw_writew(0x0001,INTSEL);
 }

arch/sh/boards/mach-se/7206/setup.c

@@ -86,20 +86,5 @@ __initcall(se7206_devices_setup);
 static struct sh_machine_vector mv_se __initmv = {
 	.mv_name		= "SolutionEngine",
 	.mv_nr_irqs		= 256,
-	.mv_inb			= se7206_inb,
-	.mv_inw			= se7206_inw,
-	.mv_outb		= se7206_outb,
-	.mv_outw		= se7206_outw,
-
-	.mv_inb_p		= se7206_inb_p,
-	.mv_inw_p		= se7206_inw,
-	.mv_outb_p		= se7206_outb_p,
-	.mv_outw_p		= se7206_outw,
-
-	.mv_insb		= se7206_insb,
-	.mv_insw		= se7206_insw,
-	.mv_outsb		= se7206_outsb,
-	.mv_outsw		= se7206_outsw,
-
 	.mv_init_irq		= init_se7206_IRQ,
 };

arch/sh/boards/mach-se/770x/Makefile

@@ -2,4 +2,4 @@
 # Makefile for the 770x SolutionEngine specific parts of the kernel
 #
 
-obj-y	 := setup.o io.o irq.o
+obj-y	 := setup.o irq.o

arch/sh/boards/mach-se/770x/io.c

-/*
- * Copyright (C) 2000  Kazumoto Kojima
- *
- * I/O routine for Hitachi SolutionEngine.
- */
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <asm/io.h>
-#include <mach-se/mach/se.h>
-
-/* MS7750 requires special versions of in*, out* routines, since
-   PC-like io ports are located at upper half byte of 16-bit word which
-   can be accessed only with 16-bit wide.  */
-
-static inline volatile __u16 *
-port2adr(unsigned int port)
-{
-	if (port & 0xff000000)
-		return ( volatile __u16 *) port;
-	if (port >= 0x2000)
-		return (volatile __u16 *) (PA_MRSHPC + (port - 0x2000));
-	else if (port >= 0x1000)
-		return (volatile __u16 *) (PA_83902 + (port << 1));
-	else
-		return (volatile __u16 *) (PA_SUPERIO + (port << 1));
-}
-
-static inline int
-shifted_port(unsigned long port)
-{
-	/* For IDE registers, value is not shifted */
-	if ((0x1f0 <= port && port < 0x1f8) || port == 0x3f6)
-		return 0;
-	else
-		return 1;
-}
-
-unsigned char se_inb(unsigned long port)
-{
-	if (shifted_port(port))
-		return (*port2adr(port) >> 8);
-	else
-		return (*port2adr(port))&0xff;
-}
-
-unsigned char se_inb_p(unsigned long port)
-{
-	unsigned long v;
-
-	if (shifted_port(port))
-		v = (*port2adr(port) >> 8);
-	else
-		v = (*port2adr(port))&0xff;
-	ctrl_delay();
-	return v;
-}
-
-unsigned short se_inw(unsigned long port)
-{
-	if (port >= 0x2000)
-		return *port2adr(port);
-	else
-		maybebadio(port);
-	return 0;
-}
-
-unsigned int se_inl(unsigned long port)
-{
-	maybebadio(port);
-	return 0;
-}
-
-void se_outb(unsigned char value, unsigned long port)
-{
-	if (shifted_port(port))
-		*(port2adr(port)) = value << 8;
-	else
-		*(port2adr(port)) = value;
-}
-
-void se_outb_p(unsigned char value, unsigned long port)
-{
-	if (shifted_port(port))
-		*(port2adr(port)) = value << 8;
-	else
-		*(port2adr(port)) = value;
-	ctrl_delay();
-}
-
-void se_outw(unsigned short value, unsigned long port)
-{
-	if (port >= 0x2000)
-		*port2adr(port) = value;
-	else
-		maybebadio(port);
-}
-
-void se_outl(unsigned int value, unsigned long port)
-{
-	maybebadio(port);
-}
-
-void se_insb(unsigned long port, void *addr, unsigned long count)
-{
-	volatile __u16 *p = port2adr(port);
-	__u8 *ap = addr;
-
-	if (shifted_port(port)) {
-		while (count--)
-			*ap++ = *p >> 8;
-	} else {
-		while (count--)
-			*ap++ = *p;
-	}
-}
-
-void se_insw(unsigned long port, void *addr, unsigned long count)
-{
-	volatile __u16 *p = port2adr(port);
-	__u16 *ap = addr;
-	while (count--)
-		*ap++ = *p;
-}
-
-void se_insl(unsigned long port, void *addr, unsigned long count)
-{
-	maybebadio(port);
-}
-
-void se_outsb(unsigned long port, const void *addr, unsigned long count)
-{
-	volatile __u16 *p = port2adr(port);
-	const __u8 *ap = addr;
-
-	if (shifted_port(port)) {
-		while (count--)
-			*p = *ap++ << 8;
-	} else {
-		while (count--)
-			*p = *ap++;
-	}
-}
-
-void se_outsw(unsigned long port, const void *addr, unsigned long count)
-{
-	volatile __u16 *p = port2adr(port);
-	const __u16 *ap = addr;
-
-	while (count--)
-		*p = *ap++;
-}
-
-void se_outsl(unsigned long port, const void *addr, unsigned long count)
-{
-	maybebadio(port);
-}

arch/sh/boards/mach-se/770x/setup.c

@@ -195,27 +195,5 @@ static struct sh_machine_vector mv_se __initmv = {
 #elif defined(CONFIG_CPU_SUBTYPE_SH7710) || defined(CONFIG_CPU_SUBTYPE_SH7712)
 	.mv_nr_irqs             = 104,
 #endif
-
-	.mv_inb			= se_inb,
-	.mv_inw			= se_inw,
-	.mv_inl			= se_inl,
-	.mv_outb		= se_outb,
-	.mv_outw		= se_outw,
-	.mv_outl		= se_outl,
-
-	.mv_inb_p		= se_inb_p,
-	.mv_inw_p		= se_inw,
-	.mv_inl_p		= se_inl,
-	.mv_outb_p		= se_outb_p,
-	.mv_outw_p		= se_outw,
-	.mv_outl_p		= se_outl,
-
-	.mv_insb		= se_insb,
-	.mv_insw		= se_insw,
-	.mv_insl		= se_insl,
-	.mv_outsb		= se_outsb,
-	.mv_outsw		= se_outsw,
-	.mv_outsl		= se_outsl,
-
 	.mv_init_irq		= init_se_IRQ,
 };

arch/sh/boards/mach-se/7751/Makefile

@@ -2,4 +2,4 @@
 # Makefile for the 7751 SolutionEngine specific parts of the kernel
 #
 
-obj-y	 := setup.o io.o irq.o
+obj-y	 := setup.o irq.o

arch/sh/boards/mach-se/7751/io.c

-/*
- * Copyright (C) 2001  Ian da Silva, Jeremy Siegel
- * Based largely on io_se.c.
- *
- * I/O routine for Hitachi 7751 SolutionEngine.
- *
- * Initial version only to support LAN access; some
- * placeholder code from io_se.c left in with the
- * expectation of later SuperIO and PCMCIA access.
- */
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <asm/io.h>
-#include <mach-se/mach/se7751.h>
-#include <asm/addrspace.h>
-
-static inline volatile u16 *port2adr(unsigned int port)
-{
-	if (port >= 0x2000)
-		return (volatile __u16 *) (PA_MRSHPC + (port - 0x2000));
-	maybebadio((unsigned long)port);
-	return (volatile __u16*)port;
-}
-
-/*
- * General outline: remap really low stuff [eventually] to SuperIO,
- * stuff in PCI IO space (at or above window at pci.h:PCIBIOS_MIN_IO)
- * is mapped through the PCI IO window.  Stuff with high bits (PXSEG)
- * should be way beyond the window, and is used  w/o translation for
- * compatibility.
- */
-unsigned char sh7751se_inb(unsigned long port)
-{
-	if (PXSEG(port))
-		return *(volatile unsigned char *)port;
-	else
-		return (*port2adr(port)) & 0xff;
-}
-
-unsigned char sh7751se_inb_p(unsigned long port)
-{
-	unsigned char v;
-
-        if (PXSEG(port))
-                v = *(volatile unsigned char *)port;
-	else
-		v = (*port2adr(port)) & 0xff;
-	ctrl_delay();
-	return v;
-}
-
-unsigned short sh7751se_inw(unsigned long port)
-{
-        if (PXSEG(port))
-                return *(volatile unsigned short *)port;
-	else if (port >= 0x2000)
-		return *port2adr(port);
-	else
-		maybebadio(port);
-	return 0;
-}
-
-unsigned int sh7751se_inl(unsigned long port)
-{
-        if (PXSEG(port))
-                return *(volatile unsigned long *)port;
-	else if (port >= 0x2000)
-		return *port2adr(port);
-	else
-		maybebadio(port);
-	return 0;
-}
-
-void sh7751se_outb(unsigned char value, unsigned long port)
-{
-
-        if (PXSEG(port))
-                *(volatile unsigned char *)port = value;
-	else
-		*(port2adr(port)) = value;
-}
-
-void sh7751se_outb_p(unsigned char value, unsigned long port)
-{
-        if (PXSEG(port))
-                *(volatile unsigned char *)port = value;
-	else
-		*(port2adr(port)) = value;
-	ctrl_delay();
-}
-
-void sh7751se_outw(unsigned short value, unsigned long port)
-{
-        if (PXSEG(port))
-                *(volatile unsigned short *)port = value;
-	else if (port >= 0x2000)
-		*port2adr(port) = value;
-	else
-		maybebadio(port);
-}
-
-void sh7751se_outl(unsigned int value, unsigned long port)
-{
-        if (PXSEG(port))
-                *(volatile unsigned long *)port = value;
-	else
-		maybebadio(port);
-}
-
-void sh7751se_insl(unsigned long port, void *addr, unsigned long count)
-{
-	maybebadio(port);
-}
-
-void sh7751se_outsl(unsigned long port, const void *addr, unsigned long count)
-{
-	maybebadio(port);
-}

arch/sh/boards/mach-se/7751/setup.c

@@ -56,23 +56,5 @@ __initcall(se7751_devices_setup);
 static struct sh_machine_vector mv_7751se __initmv = {
 	.mv_name		= "7751 SolutionEngine",
 	.mv_nr_irqs		= 72,
-
-	.mv_inb			= sh7751se_inb,
-	.mv_inw			= sh7751se_inw,
-	.mv_inl			= sh7751se_inl,
-	.mv_outb		= sh7751se_outb,
-	.mv_outw		= sh7751se_outw,
-	.mv_outl		= sh7751se_outl,
-
-	.mv_inb_p		= sh7751se_inb_p,
-	.mv_inw_p		= sh7751se_inw,
-	.mv_inl_p		= sh7751se_inl,
-	.mv_outb_p		= sh7751se_outb_p,
-	.mv_outw_p		= sh7751se_outw,
-	.mv_outl_p		= sh7751se_outl,
-
-	.mv_insl		= sh7751se_insl,
-	.mv_outsl		= sh7751se_outsl,
-
 	.mv_init_irq		= init_7751se_IRQ,
 };

arch/sh/boards/mach-snapgear/Makefile

-#
-# Makefile for the SnapGear specific parts of the kernel
-#
-
-obj-y	 := setup.o io.o

arch/sh/boards/mach-snapgear/io.c

-/*
- * Copyright (C) 2002  David McCullough <davidm@snapgear.com>
- * Copyright (C) 2001  Ian da Silva, Jeremy Siegel
- * Based largely on io_se.c.
- *
- * I/O routine for Hitachi 7751 SolutionEngine.
- *
- * Initial version only to support LAN access; some
- * placeholder code from io_se.c left in with the
- * expectation of later SuperIO and PCMCIA access.
- */
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <asm/io.h>
-#include <asm/addrspace.h>
-
-#ifdef CONFIG_SH_SECUREEDGE5410
-unsigned short secureedge5410_ioport;
-#endif
-
-static inline volatile __u16 *port2adr(unsigned int port)
-{
-	maybebadio((unsigned long)port);
-	return (volatile __u16*)port;
-}
-
-/*
- * General outline: remap really low stuff [eventually] to SuperIO,
- * stuff in PCI IO space (at or above window at pci.h:PCIBIOS_MIN_IO)
- * is mapped through the PCI IO window.  Stuff with high bits (PXSEG)
- * should be way beyond the window, and is used  w/o translation for
- * compatibility.
- */
-unsigned char snapgear_inb(unsigned long port)
-{
-	if (PXSEG(port))
-		return *(volatile unsigned char *)port;
-	else
-		return (*port2adr(port)) & 0xff;
-}
-
-unsigned char snapgear_inb_p(unsigned long port)
-{
-	unsigned char v;
-
-	if (PXSEG(port))
-		v = *(volatile unsigned char *)port;
-	else
-		v = (*port2adr(port))&0xff;
-	ctrl_delay();
-	return v;
-}
-
-unsigned short snapgear_inw(unsigned long port)
-{
-	if (PXSEG(port))
-		return *(volatile unsigned short *)port;
-	else if (port >= 0x2000)
-		return *port2adr(port);
-	else
-		maybebadio(port);
-	return 0;
-}
-
-unsigned int snapgear_inl(unsigned long port)
-{
-	if (PXSEG(port))
-		return *(volatile unsigned long *)port;
-	else if (port >= 0x2000)
-		return *port2adr(port);
-	else
-		maybebadio(port);
-	return 0;
-}
-
-void snapgear_outb(unsigned char value, unsigned long port)
-{
-
-	if (PXSEG(port))
-		*(volatile unsigned char *)port = value;
-	else
-		*(port2adr(port)) = value;
-}
-
-void snapgear_outb_p(unsigned char value, unsigned long port)
-{
-	if (PXSEG(port))
-		*(volatile unsigned char *)port = value;
-	else
-		*(port2adr(port)) = value;
-	ctrl_delay();
-}
-
-void snapgear_outw(unsigned short value, unsigned long port)
-{
-	if (PXSEG(port))
-		*(volatile unsigned short *)port = value;
-	else if (port >= 0x2000)
-		*port2adr(port) = value;
-	else
-		maybebadio(port);
-}
-
-void snapgear_outl(unsigned int value, unsigned long port)
-{
-	if (PXSEG(port))
-		*(volatile unsigned long *)port = value;
-	else
-		maybebadio(port);
-}
-
-void snapgear_insl(unsigned long port, void *addr, unsigned long count)
-{
-	maybebadio(port);
-}
-
-void snapgear_outsl(unsigned long port, const void *addr, unsigned long count)
-{
-	maybebadio(port);
-}

arch/sh/boards/mach-systemh/Makefile

-#
-# Makefile for the SystemH specific parts of the kernel
-#
-
-obj-y	 := setup.o irq.o io.o
-
-# XXX: This wants to be consolidated in arch/sh/drivers/pci, and more
-# importantly, with the generic sh7751_pcic_init() code. For now, we'll
-# just abuse the hell out of kbuild, because we can..
-
-obj-$(CONFIG_PCI) += pci.o
-pci-y := ../../se/7751/pci.o
-

arch/sh/boards/mach-systemh/io.c

-/*
- * linux/arch/sh/boards/renesas/systemh/io.c
- *
- * Copyright (C) 2001  Ian da Silva, Jeremy Siegel
- * Based largely on io_se.c.
- *
- * I/O routine for Hitachi 7751 Systemh.
- */
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <mach/systemh7751.h>
-#include <asm/addrspace.h>
-#include <asm/io.h>
-
-#define ETHER_IOMAP(adr) (0xB3000000 + (adr)) /*map to 16bits access area
-                                                of smc lan chip*/
-static inline volatile __u16 *
-port2adr(unsigned int port)
-{
-	if (port >= 0x2000)
-		return (volatile __u16 *) (PA_MRSHPC + (port - 0x2000));
-	maybebadio((unsigned long)port);
-	return (volatile __u16*)port;
-}
-
-/*
- * General outline: remap really low stuff [eventually] to SuperIO,
- * stuff in PCI IO space (at or above window at pci.h:PCIBIOS_MIN_IO)
- * is mapped through the PCI IO window.  Stuff with high bits (PXSEG)
- * should be way beyond the window, and is used  w/o translation for
- * compatibility.
- */
-unsigned char sh7751systemh_inb(unsigned long port)
-{
-	if (PXSEG(port))
-		return *(volatile unsigned char *)port;
-	else if (port <= 0x3F1)
-		return *(volatile unsigned char *)ETHER_IOMAP(port);
-	else
-		return (*port2adr(port))&0xff;
-}
-
-unsigned char sh7751systemh_inb_p(unsigned long port)
-{
-	unsigned char v;
-
-        if (PXSEG(port))
-                v = *(volatile unsigned char *)port;
-	else if (port <= 0x3F1)
-		v = *(volatile unsigned char *)ETHER_IOMAP(port);
-	else
-		v = (*port2adr(port))&0xff;
-	ctrl_delay();
-	return v;
-}
-
-unsigned short sh7751systemh_inw(unsigned long port)
-{
-        if (PXSEG(port))
-                return *(volatile unsigned short *)port;
-	else if (port >= 0x2000)
-		return *port2adr(port);
-	else if (port <= 0x3F1)
-		return *(volatile unsigned int *)ETHER_IOMAP(port);
-	else
-		maybebadio(port);
-	return 0;
-}
-
-unsigned int sh7751systemh_inl(unsigned long port)
-{
-        if (PXSEG(port))
-                return *(volatile unsigned long *)port;
-	else if (port >= 0x2000)
-		return *port2adr(port);
-	else if (port <= 0x3F1)
-		return *(volatile unsigned int *)ETHER_IOMAP(port);
-	else
-		maybebadio(port);
-	return 0;
-}
-
-void sh7751systemh_outb(unsigned char value, unsigned long port)
-{
-
-        if (PXSEG(port))
-                *(volatile unsigned char *)port = value;
-	else if (port <= 0x3F1)
-		*(volatile unsigned char *)ETHER_IOMAP(port) = value;
-	else
-		*(port2adr(port)) = value;
-}
-
-void sh7751systemh_outb_p(unsigned char value, unsigned long port)
-{
-        if (PXSEG(port))
-                *(volatile unsigned char *)port = value;
-	else if (port <= 0x3F1)
-		*(volatile unsigned char *)ETHER_IOMAP(port) = value;
-	else
-		*(port2adr(port)) = value;
-	ctrl_delay();
-}
-
-void sh7751systemh_outw(unsigned short value, unsigned long port)
-{
-        if (PXSEG(port))
-                *(volatile unsigned short *)port = value;
-	else if (port >= 0x2000)
-		*port2adr(port) = value;
-	else if (port <= 0x3F1)
-		*(volatile unsigned short *)ETHER_IOMAP(port) = value;
-	else
-		maybebadio(port);
-}
-
-void sh7751systemh_outl(unsigned int value, unsigned long port)
-{
-        if (PXSEG(port))
-                *(volatile unsigned long *)port = value;
-	else
-		maybebadio(port);
-}
-
-void sh7751systemh_insb(unsigned long port, void *addr, unsigned long count)
-{
-	unsigned char *p = addr;
-	while (count--) *p++ = sh7751systemh_inb(port);
-}
-
-void sh7751systemh_insw(unsigned long port, void *addr, unsigned long count)
-{
-	unsigned short *p = addr;
-	while (count--) *p++ = sh7751systemh_inw(port);
-}
-
-void sh7751systemh_insl(unsigned long port, void *addr, unsigned long count)
-{
-	maybebadio(port);
-}
-
-void sh7751systemh_outsb(unsigned long port, const void *addr, unsigned long count)
-{
-	unsigned char *p = (unsigned char*)addr;
-	while (count--) sh7751systemh_outb(*p++, port);
-}
-
-void sh7751systemh_outsw(unsigned long port, const void *addr, unsigned long count)
-{
-	unsigned short *p = (unsigned short*)addr;
-	while (count--) sh7751systemh_outw(*p++, port);
-}
-
-void sh7751systemh_outsl(unsigned long port, const void *addr, unsigned long count)
-{
-	maybebadio(port);
-}

arch/sh/boards/mach-systemh/irq.c

-/*
- * linux/arch/sh/boards/renesas/systemh/irq.c
- *
- * Copyright (C) 2000  Kazumoto Kojima
- *
- * Hitachi SystemH Support.
- *
- * Modified for 7751 SystemH by
- * Jonathan Short.
- */
-
-#include <linux/init.h>
-#include <linux/irq.h>
-#include <linux/interrupt.h>
-#include <linux/io.h>
-
-#include <mach/systemh7751.h>
-#include <asm/smc37c93x.h>
-
-/* address of external interrupt mask register
- * address must be set prior to use these (maybe in init_XXX_irq())
- * XXX : is it better to use .config than specifying it in code? */
-static unsigned long *systemh_irq_mask_register = (unsigned long *)0xB3F10004;
-static unsigned long *systemh_irq_request_register = (unsigned long *)0xB3F10000;
-
-static void disable_systemh_irq(struct irq_data *data)
-{
-	unsigned long val, mask = 0x01 << 1;
-
-	/* Clear the "irq"th bit in the mask and set it in the request */
-	val = __raw_readl((unsigned long)systemh_irq_mask_register);
-	val &= ~mask;
-	__raw_writel(val, (unsigned long)systemh_irq_mask_register);
-
-	val = __raw_readl((unsigned long)systemh_irq_request_register);
-	val |= mask;
-	__raw_writel(val, (unsigned long)systemh_irq_request_register);
-}
-
-static void enable_systemh_irq(struct irq_data *data)
-{
-	unsigned long val, mask = 0x01 << 1;
-
-	/* Set "irq"th bit in the mask register */
-	val = __raw_readl((unsigned long)systemh_irq_mask_register);
-	val |= mask;
-	__raw_writel(val, (unsigned long)systemh_irq_mask_register);
-}
-
-static struct irq_chip systemh_irq_type = {
-	.name		= "SystemH Register",
-	.irq_unmask	= enable_systemh_irq,
-	.irq_mask	= disable_systemh_irq,
-};
-
-void make_systemh_irq(unsigned int irq)
-{
-	disable_irq_nosync(irq);
-	set_irq_chip_and_handler(irq, &systemh_irq_type, handle_level_irq);
-	disable_systemh_irq(irq_get_irq_data(irq));
-}

arch/sh/boards/mach-systemh/setup.c

-/*
- * linux/arch/sh/boards/renesas/systemh/setup.c
- *
- * Copyright (C) 2000  Kazumoto Kojima
- * Copyright (C) 2003  Paul Mundt
- *
- * Hitachi SystemH Support.
- *
- * Modified for 7751 SystemH by Jonathan Short.
- *
- * Rewritten for 2.6 by Paul Mundt.
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-#include <linux/init.h>
-#include <asm/machvec.h>
-#include <mach/systemh7751.h>
-
-extern void make_systemh_irq(unsigned int irq);
-
-/*
- * Initialize IRQ setting
- */
-static void __init sh7751systemh_init_irq(void)
-{
-	make_systemh_irq(0xb);	/* Ethernet interrupt */
-}
-
-static struct sh_machine_vector mv_7751systemh __initmv = {
-	.mv_name		= "7751 SystemH",
-	.mv_nr_irqs		= 72,
-
-	.mv_inb			= sh7751systemh_inb,
-	.mv_inw			= sh7751systemh_inw,
-	.mv_inl			= sh7751systemh_inl,
-	.mv_outb		= sh7751systemh_outb,
-	.mv_outw		= sh7751systemh_outw,
-	.mv_outl		= sh7751systemh_outl,
-
-	.mv_inb_p		= sh7751systemh_inb_p,
-	.mv_inw_p		= sh7751systemh_inw,
-	.mv_inl_p		= sh7751systemh_inl,
-	.mv_outb_p		= sh7751systemh_outb_p,
-	.mv_outw_p		= sh7751systemh_outw,
-	.mv_outl_p		= sh7751systemh_outl,
-
-	.mv_insb		= sh7751systemh_insb,
-	.mv_insw		= sh7751systemh_insw,
-	.mv_insl		= sh7751systemh_insl,
-	.mv_outsb		= sh7751systemh_outsb,
-	.mv_outsw		= sh7751systemh_outsw,
-	.mv_outsl		= sh7751systemh_outsl,
-
-	.mv_init_irq		= sh7751systemh_init_irq,
-};

arch/sh/configs/systemh_defconfig

-CONFIG_EXPERIMENTAL=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
-# CONFIG_SYSCTL_SYSCALL is not set
-# CONFIG_HOTPLUG is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_CPU_SUBTYPE_SH7751R=y
-CONFIG_MEMORY_START=0x0c000000
-CONFIG_MEMORY_SIZE=0x00400000
-CONFIG_FLATMEM_MANUAL=y
-CONFIG_SH_7751_SYSTEMH=y
-CONFIG_PREEMPT=y
-# CONFIG_STANDALONE is not set
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=1024
-# CONFIG_INPUT is not set
-# CONFIG_SERIO_SERPORT is not set
-# CONFIG_VT is not set
-CONFIG_HW_RANDOM=y
-CONFIG_PROC_KCORE=y
-CONFIG_TMPFS=y
-CONFIG_CRAMFS=y
-CONFIG_ROMFS_FS=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set

arch/sh/include/asm/addrspace.h

@@ -44,10 +44,10 @@
 /*
  * These will never work in 32-bit, don't even bother.
  */
-#define P1SEGADDR(a)	__futile_remapping_attempt
-#define P2SEGADDR(a)	__futile_remapping_attempt
-#define P3SEGADDR(a)	__futile_remapping_attempt
-#define P4SEGADDR(a)	__futile_remapping_attempt
+#define P1SEGADDR(a)	({ (void)(a); BUG(); NULL; })
+#define P2SEGADDR(a)	({ (void)(a); BUG(); NULL; })
+#define P3SEGADDR(a)	({ (void)(a); BUG(); NULL; })
+#define P4SEGADDR(a)	({ (void)(a); BUG(); NULL; })
 #endif
 #endif /* P1SEG */
 

arch/sh/include/asm/pgtable.h

@@ -66,7 +66,6 @@ static inline unsigned long long neff_sign_extend(unsigned long val)
 #define PHYS_ADDR_MASK29		0x1fffffff
 #define PHYS_ADDR_MASK32		0xffffffff
 
-#ifdef CONFIG_PMB
 static inline unsigned long phys_addr_mask(void)
 {
 	/* Is the MMU in 29bit mode? */
@@ -75,17 +74,6 @@ static inline unsigned long phys_addr_mask(void)
 
 	return PHYS_ADDR_MASK32;
 }
-#elif defined(CONFIG_32BIT)
-static inline unsigned long phys_addr_mask(void)
-{
-	return PHYS_ADDR_MASK32;
-}
-#else
-static inline unsigned long phys_addr_mask(void)
-{
-	return PHYS_ADDR_MASK29;
-}
-#endif
 
 #define PTE_PHYS_MASK		(phys_addr_mask() & PAGE_MASK)
 #define PTE_FLAGS_MASK		(~(PTE_PHYS_MASK) << PAGE_SHIFT)

arch/sh/include/asm/system.h

@@ -10,6 +10,7 @@
 #include <linux/compiler.h>
 #include <linux/linkage.h>
 #include <asm/types.h>
+#include <asm/uncached.h>
 
 #define AT_VECTOR_SIZE_ARCH 5 /* entries in ARCH_DLINFO */
 
@@ -137,9 +138,6 @@ extern unsigned int instruction_size(unsigned int insn);
 #define instruction_size(insn)	(4)
 #endif
 
-extern unsigned long cached_to_uncached;
-extern unsigned long uncached_size;
-
 void per_cpu_trap_init(void);
 void default_idle(void);
 void cpu_idle_wait(void);

arch/sh/include/asm/system_32.h

@@ -145,42 +145,6 @@ do {								\
 		__restore_dsp(prev);				\
 } while (0)
 
-/*
- * Jump to uncached area.
- * When handling TLB or caches, we need to do it from an uncached area.
- */
-#define jump_to_uncached()			\
-do {						\
-	unsigned long __dummy;			\
-						\
-	__asm__ __volatile__(			\
-		"mova	1f, %0\n\t"		\
-		"add	%1, %0\n\t"		\
-		"jmp	@%0\n\t"		\
-		" nop\n\t"			\
-		".balign 4\n"			\
-		"1:"				\
-		: "=&z" (__dummy)		\
-		: "r" (cached_to_uncached));	\
-} while (0)
-
-/*
- * Back to cached area.
- */
-#define back_to_cached()				\
-do {							\
-	unsigned long __dummy;				\
-	ctrl_barrier();					\
-	__asm__ __volatile__(				\
-		"mov.l	1f, %0\n\t"			\
-		"jmp	@%0\n\t"			\
-		" nop\n\t"				\
-		".balign 4\n"				\
-		"1:	.long 2f\n"			\
-		"2:"					\
-		: "=&r" (__dummy));			\
-} while (0)
-
 #ifdef CONFIG_CPU_HAS_SR_RB
 #define lookup_exception_vector()	\
 ({					\

arch/sh/include/asm/system_64.h

@@ -34,9 +34,6 @@ do {								\
 			      &next->thread);			\
 } while (0)
 
-#define jump_to_uncached()	do { } while (0)
-#define back_to_cached()	do { } while (0)
-
 #define __icbi(addr)	__asm__ __volatile__ ( "icbi %0, 0\n\t" : : "r" (addr))
 #define __ocbp(addr)	__asm__ __volatile__ ( "ocbp %0, 0\n\t" : : "r" (addr))
 #define __ocbi(addr)	__asm__ __volatile__ ( "ocbi %0, 0\n\t" : : "r" (addr))

arch/sh/include/asm/uncached.h

@@ -4,15 +4,55 @@
 #include <linux/bug.h>
 
 #ifdef CONFIG_UNCACHED_MAPPING
+extern unsigned long cached_to_uncached;
+extern unsigned long uncached_size;
 extern unsigned long uncached_start, uncached_end;
 
 extern int virt_addr_uncached(unsigned long kaddr);
 extern void uncached_init(void);
 extern void uncached_resize(unsigned long size);
+
+/*
+ * Jump to uncached area.
+ * When handling TLB or caches, we need to do it from an uncached area.
+ */
+#define jump_to_uncached()			\
+do {						\
+	unsigned long __dummy;			\
+						\
+	__asm__ __volatile__(			\
+		"mova	1f, %0\n\t"		\
+		"add	%1, %0\n\t"		\
+		"jmp	@%0\n\t"		\
+		" nop\n\t"			\
+		".balign 4\n"			\
+		"1:"				\
+		: "=&z" (__dummy)		\
+		: "r" (cached_to_uncached));	\
+} while (0)
+
+/*
+ * Back to cached area.
+ */
+#define back_to_cached()				\
+do {							\
+	unsigned long __dummy;				\
+	ctrl_barrier();					\
+	__asm__ __volatile__(				\
+		"mov.l	1f, %0\n\t"			\
+		"jmp	@%0\n\t"			\
+		" nop\n\t"				\
+		".balign 4\n"				\
+		"1:	.long 2f\n"			\
+		"2:"					\
+		: "=&r" (__dummy));			\
+} while (0)
 #else
 #define virt_addr_uncached(kaddr)	(0)
 #define uncached_init()			do { } while (0)
 #define uncached_resize(size)		BUG()
+#define jump_to_uncached()		do { } while (0)
+#define back_to_cached()		do { } while (0)
 #endif
 
 #endif /* __ASM_SH_UNCACHED_H */

arch/sh/include/mach-common/mach/edosk7705.h

-#ifndef __ASM_SH_EDOSK7705_H
-#define __ASM_SH_EDOSK7705_H
-
-#define __IO_PREFIX sh_edosk7705
-#include <asm/io_generic.h>
-
-#endif /* __ASM_SH_EDOSK7705_H */

arch/sh/include/mach-common/mach/microdev.h

@@ -68,13 +68,4 @@ extern void microdev_print_fpga_intc_status(void);
 #define __IO_PREFIX microdev
 #include <asm/io_generic.h>
 
-#if defined(CONFIG_PCI)
-unsigned char  microdev_pci_inb(unsigned long port);
-unsigned short microdev_pci_inw(unsigned long port);
-unsigned long  microdev_pci_inl(unsigned long port);
-void           microdev_pci_outb(unsigned char  data, unsigned long port);
-void           microdev_pci_outw(unsigned short data, unsigned long port);
-void           microdev_pci_outl(unsigned long  data, unsigned long port);
-#endif
-
 #endif /* __ASM_SH_MICRODEV_H */

arch/sh/include/mach-common/mach/snapgear.h → arch/sh/include/mach-common/mach/secureedge5410.h

@@ -12,30 +12,9 @@
 #ifndef _ASM_SH_IO_SNAPGEAR_H
 #define _ASM_SH_IO_SNAPGEAR_H
 
-#if defined(CONFIG_CPU_SH4)
-/*
- * The external interrupt lines, these take up ints 0 - 15 inclusive
- * depending on the priority for the interrupt.  In fact the priority
- * is the interrupt :-)
- */
-
-#define IRL0_IRQ	2
-#define IRL0_PRIORITY	13
-
-#define IRL1_IRQ	5
-#define IRL1_PRIORITY	10
-
-#define IRL2_IRQ	8
-#define IRL2_PRIORITY	7
-
-#define IRL3_IRQ	11
-#define IRL3_PRIORITY	4
-#endif
-
 #define __IO_PREFIX	snapgear
 #include <asm/io_generic.h>
 
-#ifdef CONFIG_SH_SECUREEDGE5410
 /*
  * We need to remember what was written to the ioport as some bits
  * are shared with other functions and you cannot read back what was
@@ -66,6 +45,5 @@ extern unsigned short secureedge5410_ioport;
 			((secureedge5410_ioport & ~(mask)) | ((val) & (mask)))))
 #define SECUREEDGE_READ_IOPORT() \
 	 ((*SECUREEDGE_IOPORT_ADDR&0x0817) | (secureedge5410_ioport&~0x0817))
-#endif
 
 #endif /* _ASM_SH_IO_SNAPGEAR_H */

arch/sh/include/mach-common/mach/systemh7751.h

-#ifndef __ASM_SH_SYSTEMH_7751SYSTEMH_H
-#define __ASM_SH_SYSTEMH_7751SYSTEMH_H
-
-/*
- * linux/include/asm-sh/systemh/7751systemh.h
- *
- * Copyright (C) 2000  Kazumoto Kojima
- *
- * Hitachi SystemH support
-
- * Modified for 7751 SystemH by
- * Jonathan Short, 2002.
- */
-
-/* Box specific addresses.  */
-
-#define PA_ROM		0x00000000	/* EPROM */
-#define PA_ROM_SIZE	0x00400000	/* EPROM size 4M byte */
-#define PA_FROM		0x01000000	/* EPROM */
-#define PA_FROM_SIZE	0x00400000	/* EPROM size 4M byte */
-#define PA_EXT1		0x04000000
-#define PA_EXT1_SIZE	0x04000000
-#define PA_EXT2		0x08000000
-#define PA_EXT2_SIZE	0x04000000
-#define PA_SDRAM	0x0c000000
-#define PA_SDRAM_SIZE	0x04000000
-
-#define PA_EXT4		0x12000000
-#define PA_EXT4_SIZE	0x02000000
-#define PA_EXT5		0x14000000
-#define PA_EXT5_SIZE	0x04000000
-#define PA_PCIC		0x18000000	/* MR-SHPC-01 PCMCIA */
-
-#define PA_DIPSW0	0xb9000000	/* Dip switch 5,6 */
-#define PA_DIPSW1	0xb9000002	/* Dip switch 7,8 */
-#define PA_LED		0xba000000	/* LED */
-#define	PA_BCR		0xbb000000	/* FPGA on the MS7751SE01 */
-
-#define PA_MRSHPC	0xb83fffe0	/* MR-SHPC-01 PCMCIA controller */
-#define PA_MRSHPC_MW1	0xb8400000	/* MR-SHPC-01 memory window base */
-#define PA_MRSHPC_MW2	0xb8500000	/* MR-SHPC-01 attribute window base */
-#define PA_MRSHPC_IO	0xb8600000	/* MR-SHPC-01 I/O window base */
-#define MRSHPC_MODE     (PA_MRSHPC + 4)
-#define MRSHPC_OPTION   (PA_MRSHPC + 6)
-#define MRSHPC_CSR      (PA_MRSHPC + 8)
-#define MRSHPC_ISR      (PA_MRSHPC + 10)
-#define MRSHPC_ICR      (PA_MRSHPC + 12)
-#define MRSHPC_CPWCR    (PA_MRSHPC + 14)
-#define MRSHPC_MW0CR1   (PA_MRSHPC + 16)
-#define MRSHPC_MW1CR1   (PA_MRSHPC + 18)
-#define MRSHPC_IOWCR1   (PA_MRSHPC + 20)
-#define MRSHPC_MW0CR2   (PA_MRSHPC + 22)
-#define MRSHPC_MW1CR2   (PA_MRSHPC + 24)
-#define MRSHPC_IOWCR2   (PA_MRSHPC + 26)
-#define MRSHPC_CDCR     (PA_MRSHPC + 28)
-#define MRSHPC_PCIC_INFO (PA_MRSHPC + 30)
-
-#define BCR_ILCRA	(PA_BCR + 0)
-#define BCR_ILCRB	(PA_BCR + 2)
-#define BCR_ILCRC	(PA_BCR + 4)
-#define BCR_ILCRD	(PA_BCR + 6)
-#define BCR_ILCRE	(PA_BCR + 8)
-#define BCR_ILCRF	(PA_BCR + 10)
-#define BCR_ILCRG	(PA_BCR + 12)
-
-#define IRQ_79C973	13
-
-#define __IO_PREFIX	sh7751systemh
-#include <asm/io_generic.h>
-
-#endif  /* __ASM_SH_SYSTEMH_7751SYSTEMH_H */

arch/sh/kernel/cpu/sh4a/clock-sh7724.c

@@ -48,7 +48,7 @@ static struct clk r_clk = {
  * Default rate for the root input clock, reset this with clk_set_rate()
  * from the platform code.
  */
-struct clk extal_clk = {
+static struct clk extal_clk = {
 	.rate		= 33333333,
 };
 
@@ -111,7 +111,7 @@ static struct clk div3_clk = {
 	.parent		= &pll_clk,
 };
 
-struct clk *main_clks[] = {
+static struct clk *main_clks[] = {
 	&r_clk,
 	&extal_clk,
 	&fll_clk,
@@ -156,7 +156,7 @@ struct clk div4_clks[DIV4_NR] = {
 
 enum { DIV6_V, DIV6_FA, DIV6_FB, DIV6_I, DIV6_S, DIV6_NR };
 
-struct clk div6_clks[DIV6_NR] = {
+static struct clk div6_clks[DIV6_NR] = {
 	[DIV6_V] = SH_CLK_DIV6(&div3_clk, VCLKCR, 0),
 	[DIV6_FA] = SH_CLK_DIV6(&div3_clk, FCLKACR, 0),
 	[DIV6_FB] = SH_CLK_DIV6(&div3_clk, FCLKBCR, 0),

arch/sh/mm/Kconfig

@@ -79,7 +79,7 @@ config 29BIT
 
 config 32BIT
 	bool
-	default y if CPU_SH5
+	default y if CPU_SH5 || !MMU
 
 config PMB
 	bool "Support 32-bit physical addressing through PMB"

arch/sh/mm/consistent.c

@@ -79,21 +79,20 @@ void dma_generic_free_coherent(struct device *dev, size_t size,
 void dma_cache_sync(struct device *dev, void *vaddr, size_t size,
 		    enum dma_data_direction direction)
 {
-#if defined(CONFIG_CPU_SH5) || defined(CONFIG_PMB)
-	void *p1addr = vaddr;
-#else
-	void *p1addr = (void*) P1SEGADDR((unsigned long)vaddr);
-#endif
+	void *addr;
+
+	addr = __in_29bit_mode() ?
+	       (void *)P1SEGADDR((unsigned long)vaddr) : vaddr;
 
 	switch (direction) {
 	case DMA_FROM_DEVICE:		/* invalidate only */
-		__flush_invalidate_region(p1addr, size);
+		__flush_invalidate_region(addr, size);
 		break;
 	case DMA_TO_DEVICE:		/* writeback only */
-		__flush_wback_region(p1addr, size);
+		__flush_wback_region(addr, size);
 		break;
 	case DMA_BIDIRECTIONAL:		/* writeback and invalidate */
-		__flush_purge_region(p1addr, size);
+		__flush_purge_region(addr, size);
 		break;
 	default:
 		BUG();

arch/sh/mm/uncached.c

@@ -28,7 +28,7 @@ EXPORT_SYMBOL(virt_addr_uncached);
 
 void __init uncached_init(void)
 {
-#ifdef CONFIG_29BIT
+#if defined(CONFIG_29BIT) || !defined(CONFIG_MMU)
 	uncached_start = P2SEG;
 #else
 	uncached_start = memory_end;

arch/sh/tools/mach-types

@@ -26,7 +26,6 @@ HD64461			HD64461
 7724SE			SH_7724_SOLUTION_ENGINE
 7751SE			SH_7751_SOLUTION_ENGINE
 7780SE			SH_7780_SOLUTION_ENGINE
-7751SYSTEMH		SH_7751_SYSTEMH
 HP6XX			SH_HP6XX
 DREAMCAST		SH_DREAMCAST
 SNAPGEAR		SH_SECUREEDGE5410

drivers/rtc/rtc-ds1302.c

@@ -35,7 +35,7 @@
 
 #ifdef CONFIG_SH_SECUREEDGE5410
 #include <asm/rtc.h>
-#include <mach/snapgear.h>
+#include <mach/secureedge5410.h>
 
 #define	RTC_RESET	0x1000
 #define	RTC_IODATA	0x0800

drivers/sh/clk/core.c

@@ -90,8 +90,8 @@ struct clk_rate_round_data {
 static long clk_rate_round_helper(struct clk_rate_round_data *rounder)
 {
 	unsigned long rate_error, rate_error_prev = ~0UL;
-	unsigned long rate_best_fit = rounder->rate;
 	unsigned long highest, lowest, freq;
+	long rate_best_fit = -ENOENT;
 	int i;
 
 	highest = 0;
@@ -146,7 +146,7 @@ long clk_rate_table_round(struct clk *clk,
 	};
 
 	if (clk->nr_freqs < 1)
-		return 0;
+		return -ENOSYS;
 
 	return clk_rate_round_helper(&table_round);
 }
@@ -541,6 +541,98 @@ long clk_round_rate(struct clk *clk, unsigned long rate)
 }
 EXPORT_SYMBOL_GPL(clk_round_rate);
 
+long clk_round_parent(struct clk *clk, unsigned long target,
+		      unsigned long *best_freq, unsigned long *parent_freq,
+		      unsigned int div_min, unsigned int div_max)
+{
+	struct cpufreq_frequency_table *freq, *best = NULL;
+	unsigned long error = ULONG_MAX, freq_high, freq_low, div;
+	struct clk *parent = clk_get_parent(clk);
+
+	if (!parent) {
+		*parent_freq = 0;
+		*best_freq = clk_round_rate(clk, target);
+		return abs(target - *best_freq);
+	}
+
+	for (freq = parent->freq_table; freq->frequency != CPUFREQ_TABLE_END;
+	     freq++) {
+		if (freq->frequency == CPUFREQ_ENTRY_INVALID)
+			continue;
+
+		if (unlikely(freq->frequency / target <= div_min - 1)) {
+			unsigned long freq_max;
+
+			freq_max = (freq->frequency + div_min / 2) / div_min;
+			if (error > target - freq_max) {
+				error = target - freq_max;
+				best = freq;
+				if (best_freq)
+					*best_freq = freq_max;
+			}
+
+			pr_debug("too low freq %lu, error %lu\n", freq->frequency,
+				 target - freq_max);
+
+			if (!error)
+				break;
+
+			continue;
+		}
+
+		if (unlikely(freq->frequency / target >= div_max)) {
+			unsigned long freq_min;
+
+			freq_min = (freq->frequency + div_max / 2) / div_max;
+			if (error > freq_min - target) {
+				error = freq_min - target;
+				best = freq;
+				if (best_freq)
+					*best_freq = freq_min;
+			}
+
+			pr_debug("too high freq %lu, error %lu\n", freq->frequency,
+				 freq_min - target);
+
+			if (!error)
+				break;
+
+			continue;
+		}
+
+		div = freq->frequency / target;
+		freq_high = freq->frequency / div;
+		freq_low = freq->frequency / (div + 1);
+
+		if (freq_high - target < error) {
+			error = freq_high - target;
+			best = freq;
+			if (best_freq)
+				*best_freq = freq_high;
+		}
+
+		if (target - freq_low < error) {
+			error = target - freq_low;
+			best = freq;
+			if (best_freq)
+				*best_freq = freq_low;
+		}
+
+		pr_debug("%u / %lu = %lu, / %lu = %lu, best %lu, parent %u\n",
+			 freq->frequency, div, freq_high, div + 1, freq_low,
+			 *best_freq, best->frequency);
+
+		if (!error)
+			break;
+	}
+
+	if (parent_freq)
+		*parent_freq = best->frequency;
+
+	return error;
+}
+EXPORT_SYMBOL_GPL(clk_round_parent);
+
 #ifdef CONFIG_PM
 static int clks_sysdev_suspend(struct sys_device *dev, pm_message_t state)
 {

drivers/sh/intc/core.c

@@ -79,7 +79,7 @@ static void __init intc_register_irq(struct intc_desc *desc,
 	 * Register the IRQ position with the global IRQ map, then insert
 	 * it in to the radix tree.
 	 */
-	irq_reserve_irqs(irq, 1);
+	irq_reserve_irq(irq);
 
 	raw_spin_lock_irqsave(&intc_big_lock, flags);
 	radix_tree_insert(&d->tree, enum_id, intc_irq_xlate_get(irq));

drivers/sh/intc/dynamic.c

@@ -60,5 +60,5 @@ void reserve_intc_vectors(struct intc_vect *vectors, unsigned int nr_vecs)
 	int i;
 
 	for (i = 0; i < nr_vecs; i++)
-		irq_reserve_irqs(evt2irq(vectors[i].vect), 1);
+		irq_reserve_irq(evt2irq(vectors[i].vect));
 }

include/linux/sh_clk.h

@@ -122,6 +122,10 @@ int clk_rate_table_find(struct clk *clk,
 long clk_rate_div_range_round(struct clk *clk, unsigned int div_min,
 			      unsigned int div_max, unsigned long rate);
 
+long clk_round_parent(struct clk *clk, unsigned long target,
+		      unsigned long *best_freq, unsigned long *parent_freq,
+		      unsigned int div_min, unsigned int div_max);
+
 #define SH_CLK_MSTP32(_parent, _enable_reg, _enable_bit, _flags)	\
 {									\
 	.parent		= _parent,					\