Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next

Jeff Kirsher says:

====================
This series contains updates to e1000e only.

v2- updates patch 09/15 "e1000e: resolve checkpatch PREFER_PR_LEVEL warning"
    based on feedback from Joe Perches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/intel/e1000e/defines.h

@@ -241,9 +241,9 @@
 #define E1000_CTRL_VME      0x40000000  /* IEEE VLAN mode enable */
 #define E1000_CTRL_PHY_RST  0x80000000  /* PHY Reset */
 
-/* Bit definitions for the Management Data IO (MDIO) and Management Data
- * Clock (MDC) pins in the Device Control Register.
- */
+#define E1000_PCS_LCTL_FORCE_FCTRL	0x80
+
+#define E1000_PCS_LSTS_AN_COMPLETE	0x10000
 
 /* Device Status */
 #define E1000_STATUS_FD         0x00000001      /* Full duplex.0=half,1=full */
@@ -639,6 +639,10 @@
 /* NVM Word Offsets */
 #define NVM_COMPAT                 0x0003
 #define NVM_ID_LED_SETTINGS        0x0004
+#define NVM_FUTURE_INIT_WORD1      0x0019
+#define NVM_COMPAT_VALID_CSUM      0x0001
+#define NVM_FUTURE_INIT_WORD1_VALID_CSUM	0x0040
+
 #define NVM_INIT_CONTROL2_REG      0x000F
 #define NVM_INIT_CONTROL3_PORT_B   0x0014
 #define NVM_INIT_3GIO_3            0x001A

drivers/net/ethernet/intel/e1000e/e1000.h

@@ -447,7 +447,7 @@ struct e1000_info {
 #define FLAG_MSI_ENABLED                  (1 << 27)
 /* reserved (1 << 28) */
 #define FLAG_TSO_FORCE                    (1 << 29)
-#define FLAG_RX_RESTART_NOW               (1 << 30)
+#define FLAG_RESTART_NOW                  (1 << 30)
 #define FLAG_MSI_TEST_FAILED              (1 << 31)
 
 #define FLAG2_CRC_STRIPPING               (1 << 0)

drivers/net/ethernet/intel/e1000e/ethtool.c

@@ -98,7 +98,6 @@ static const struct e1000_stats e1000_gstrings_stats[] = {
 	E1000_STAT("rx_flow_control_xoff", stats.xoffrxc),
 	E1000_STAT("tx_flow_control_xon", stats.xontxc),
 	E1000_STAT("tx_flow_control_xoff", stats.xofftxc),
-	E1000_STAT("rx_long_byte_count", stats.gorc),
 	E1000_STAT("rx_csum_offload_good", hw_csum_good),
 	E1000_STAT("rx_csum_offload_errors", hw_csum_err),
 	E1000_STAT("rx_header_split", rx_hdr_split),

drivers/net/ethernet/intel/e1000e/hw.h

@@ -191,6 +191,10 @@ enum e1e_registers {
 	E1000_ICTXQMTC = 0x0411C, /* Irq Cause Tx Queue MinThreshold Count */
 	E1000_ICRXDMTC = 0x04120, /* Irq Cause Rx Desc MinThreshold Count */
 	E1000_ICRXOC   = 0x04124, /* Irq Cause Receiver Overrun Count */
+	E1000_PCS_LCTL = 0x04208, /* PCS Link Control - RW */
+	E1000_PCS_LSTAT = 0x0420C, /* PCS Link Status - RO */
+	E1000_PCS_ANADV = 0x04218, /* AN advertisement - RW */
+	E1000_PCS_LPAB = 0x0421C, /* Link Partner Ability - RW */
 	E1000_RXCSUM   = 0x05000, /* Rx Checksum Control - RW */
 	E1000_RFCTL    = 0x05008, /* Receive Filter Control */
 	E1000_MTA      = 0x05200, /* Multicast Table Array - RW Array */

drivers/net/ethernet/intel/e1000e/mac.c

@@ -1021,6 +1021,7 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 {
 	struct e1000_mac_info *mac = &hw->mac;
 	s32 ret_val = 0;
+	u32 pcs_status_reg, pcs_adv_reg, pcs_lp_ability_reg, pcs_ctrl_reg;
 	u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg;
 	u16 speed, duplex;
 
@@ -1185,6 +1186,130 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 		}
 	}
 
+	/* Check for the case where we have SerDes media and auto-neg is
+	 * enabled.  In this case, we need to check and see if Auto-Neg
+	 * has completed, and if so, how the PHY and link partner has
+	 * flow control configured.
+	 */
+	if ((hw->phy.media_type == e1000_media_type_internal_serdes) &&
+	    mac->autoneg) {
+		/* Read the PCS_LSTS and check to see if AutoNeg
+		 * has completed.
+		 */
+		pcs_status_reg = er32(PCS_LSTAT);
+
+		if (!(pcs_status_reg & E1000_PCS_LSTS_AN_COMPLETE)) {
+			e_dbg("PCS Auto Neg has not completed.\n");
+			return ret_val;
+		}
+
+		/* The AutoNeg process has completed, so we now need to
+		 * read both the Auto Negotiation Advertisement
+		 * Register (PCS_ANADV) and the Auto_Negotiation Base
+		 * Page Ability Register (PCS_LPAB) to determine how
+		 * flow control was negotiated.
+		 */
+		pcs_adv_reg = er32(PCS_ANADV);
+		pcs_lp_ability_reg = er32(PCS_LPAB);
+
+		/* Two bits in the Auto Negotiation Advertisement Register
+		 * (PCS_ANADV) and two bits in the Auto Negotiation Base
+		 * Page Ability Register (PCS_LPAB) determine flow control
+		 * for both the PHY and the link partner.  The following
+		 * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
+		 * 1999, describes these PAUSE resolution bits and how flow
+		 * control is determined based upon these settings.
+		 * NOTE:  DC = Don't Care
+		 *
+		 *   LOCAL DEVICE  |   LINK PARTNER
+		 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
+		 *-------|---------|-------|---------|--------------------
+		 *   0   |    0    |  DC   |   DC    | e1000_fc_none
+		 *   0   |    1    |   0   |   DC    | e1000_fc_none
+		 *   0   |    1    |   1   |    0    | e1000_fc_none
+		 *   0   |    1    |   1   |    1    | e1000_fc_tx_pause
+		 *   1   |    0    |   0   |   DC    | e1000_fc_none
+		 *   1   |   DC    |   1   |   DC    | e1000_fc_full
+		 *   1   |    1    |   0   |    0    | e1000_fc_none
+		 *   1   |    1    |   0   |    1    | e1000_fc_rx_pause
+		 *
+		 * Are both PAUSE bits set to 1?  If so, this implies
+		 * Symmetric Flow Control is enabled at both ends.  The
+		 * ASM_DIR bits are irrelevant per the spec.
+		 *
+		 * For Symmetric Flow Control:
+		 *
+		 *   LOCAL DEVICE  |   LINK PARTNER
+		 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+		 *-------|---------|-------|---------|--------------------
+		 *   1   |   DC    |   1   |   DC    | e1000_fc_full
+		 *
+		 */
+		if ((pcs_adv_reg & E1000_TXCW_PAUSE) &&
+		    (pcs_lp_ability_reg & E1000_TXCW_PAUSE)) {
+			/* Now we need to check if the user selected Rx ONLY
+			 * of pause frames.  In this case, we had to advertise
+			 * FULL flow control because we could not advertise Rx
+			 * ONLY. Hence, we must now check to see if we need to
+			 * turn OFF the TRANSMISSION of PAUSE frames.
+			 */
+			if (hw->fc.requested_mode == e1000_fc_full) {
+				hw->fc.current_mode = e1000_fc_full;
+				e_dbg("Flow Control = FULL.\n");
+			} else {
+				hw->fc.current_mode = e1000_fc_rx_pause;
+				e_dbg("Flow Control = Rx PAUSE frames only.\n");
+			}
+		}
+		/* For receiving PAUSE frames ONLY.
+		 *
+		 *   LOCAL DEVICE  |   LINK PARTNER
+		 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+		 *-------|---------|-------|---------|--------------------
+		 *   0   |    1    |   1   |    1    | e1000_fc_tx_pause
+		 */
+		else if (!(pcs_adv_reg & E1000_TXCW_PAUSE) &&
+			 (pcs_adv_reg & E1000_TXCW_ASM_DIR) &&
+			 (pcs_lp_ability_reg & E1000_TXCW_PAUSE) &&
+			 (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) {
+			hw->fc.current_mode = e1000_fc_tx_pause;
+			e_dbg("Flow Control = Tx PAUSE frames only.\n");
+		}
+		/* For transmitting PAUSE frames ONLY.
+		 *
+		 *   LOCAL DEVICE  |   LINK PARTNER
+		 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+		 *-------|---------|-------|---------|--------------------
+		 *   1   |    1    |   0   |    1    | e1000_fc_rx_pause
+		 */
+		else if ((pcs_adv_reg & E1000_TXCW_PAUSE) &&
+			 (pcs_adv_reg & E1000_TXCW_ASM_DIR) &&
+			 !(pcs_lp_ability_reg & E1000_TXCW_PAUSE) &&
+			 (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) {
+			hw->fc.current_mode = e1000_fc_rx_pause;
+			e_dbg("Flow Control = Rx PAUSE frames only.\n");
+		} else {
+			/* Per the IEEE spec, at this point flow control
+			 * should be disabled.
+			 */
+			hw->fc.current_mode = e1000_fc_none;
+			e_dbg("Flow Control = NONE.\n");
+		}
+
+		/* Now we call a subroutine to actually force the MAC
+		 * controller to use the correct flow control settings.
+		 */
+		pcs_ctrl_reg = er32(PCS_LCTL);
+		pcs_ctrl_reg |= E1000_PCS_LCTL_FORCE_FCTRL;
+		ew32(PCS_LCTL, pcs_ctrl_reg);
+
+		ret_val = e1000e_force_mac_fc(hw);
+		if (ret_val) {
+			e_dbg("Error forcing flow control settings\n");
+			return ret_val;
+		}
+	}
+
 	return 0;
 }
 

drivers/net/ethernet/intel/e1000e/netdev.c

@@ -765,7 +765,7 @@ static void e1000_alloc_jumbo_rx_buffers(struct e1000_ring *rx_ring,
 	struct e1000_buffer *buffer_info;
 	struct sk_buff *skb;
 	unsigned int i;
-	unsigned int bufsz = 256 - 16 /* for skb_reserve */;
+	unsigned int bufsz = 256 - 16;	/* for skb_reserve */
 
 	i = rx_ring->next_to_use;
 	buffer_info = &rx_ring->buffer_info[i];
@@ -1671,7 +1671,7 @@ static irqreturn_t e1000_intr_msi(int irq, void *data)
 			/* disable receives */
 			u32 rctl = er32(RCTL);
 			ew32(RCTL, rctl & ~E1000_RCTL_EN);
-			adapter->flags |= FLAG_RX_RESTART_NOW;
+			adapter->flags |= FLAG_RESTART_NOW;
 		}
 		/* guard against interrupt when we're going down */
 		if (!test_bit(__E1000_DOWN, &adapter->state))
@@ -1734,7 +1734,7 @@ static irqreturn_t e1000_intr(int irq, void *data)
 			/* disable receives */
 			rctl = er32(RCTL);
 			ew32(RCTL, rctl & ~E1000_RCTL_EN);
-			adapter->flags |= FLAG_RX_RESTART_NOW;
+			adapter->flags |= FLAG_RESTART_NOW;
 		}
 		/* guard against interrupt when we're going down */
 		if (!test_bit(__E1000_DOWN, &adapter->state))
@@ -2405,7 +2405,6 @@ static unsigned int e1000_update_itr(struct e1000_adapter *adapter,
 
 static void e1000_set_itr(struct e1000_adapter *adapter)
 {
-	struct e1000_hw *hw = &adapter->hw;
 	u16 current_itr;
 	u32 new_itr = adapter->itr;
 
@@ -2468,10 +2467,7 @@ static void e1000_set_itr(struct e1000_adapter *adapter)
 		if (adapter->msix_entries)
 			adapter->rx_ring->set_itr = 1;
 		else
-			if (new_itr)
-				ew32(ITR, 1000000000 / (new_itr * 256));
-			else
-				ew32(ITR, 0);
+			e1000e_write_itr(adapter, new_itr);
 	}
 }
 
@@ -3013,7 +3009,7 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
 
 	ew32(RCTL, rctl);
 	/* just started the receive unit, no need to restart */
-	adapter->flags &= ~FLAG_RX_RESTART_NOW;
+	adapter->flags &= ~FLAG_RESTART_NOW;
 }
 
 /**
@@ -4300,9 +4296,8 @@ static void e1000_print_link_info(struct e1000_adapter *adapter)
 	u32 ctrl = er32(CTRL);
 
 	/* Link status message must follow this format for user tools */
-	printk(KERN_INFO "e1000e: %s NIC Link is Up %d Mbps %s Duplex, Flow Control: %s\n",
-		adapter->netdev->name,
-		adapter->link_speed,
+	pr_info("%s NIC Link is Up %d Mbps %s Duplex, Flow Control: %s\n",
+		adapter->netdev->name, adapter->link_speed,
 		adapter->link_duplex == FULL_DUPLEX ? "Full" : "Half",
 		(ctrl & E1000_CTRL_TFCE) && (ctrl & E1000_CTRL_RFCE) ? "Rx/Tx" :
 		(ctrl & E1000_CTRL_RFCE) ? "Rx" :
@@ -4355,11 +4350,11 @@ static void e1000e_enable_receives(struct e1000_adapter *adapter)
 {
 	/* make sure the receive unit is started */
 	if ((adapter->flags & FLAG_RX_NEEDS_RESTART) &&
-	    (adapter->flags & FLAG_RX_RESTART_NOW)) {
+	    (adapter->flags & FLAG_RESTART_NOW)) {
 		struct e1000_hw *hw = &adapter->hw;
 		u32 rctl = er32(RCTL);
 		ew32(RCTL, rctl | E1000_RCTL_EN);
-		adapter->flags &= ~FLAG_RX_RESTART_NOW;
+		adapter->flags &= ~FLAG_RESTART_NOW;
 	}
 }
 
@@ -4521,15 +4516,22 @@ static void e1000_watchdog_task(struct work_struct *work)
 			adapter->link_speed = 0;
 			adapter->link_duplex = 0;
 			/* Link status message must follow this format */
-			printk(KERN_INFO "e1000e: %s NIC Link is Down\n",
-			       adapter->netdev->name);
+			pr_info("%s NIC Link is Down\n", adapter->netdev->name);
 			netif_carrier_off(netdev);
 			if (!test_bit(__E1000_DOWN, &adapter->state))
 				mod_timer(&adapter->phy_info_timer,
 					  round_jiffies(jiffies + 2 * HZ));
 
-			if (adapter->flags & FLAG_RX_NEEDS_RESTART)
-				schedule_work(&adapter->reset_task);
+			/* The link is lost so the controller stops DMA.
+			 * If there is queued Tx work that cannot be done
+			 * or if on an 8000ES2LAN which requires a Rx packet
+			 * buffer work-around on link down event, reset the
+			 * controller to flush the Tx/Rx packet buffers.
+			 * (Do the reset outside of interrupt context).
+			 */
+			if ((adapter->flags & FLAG_RX_NEEDS_RESTART) ||
+			    (e1000_desc_unused(tx_ring) + 1 < tx_ring->count))
+				adapter->flags |= FLAG_RESTART_NOW;
 			else
 				pm_schedule_suspend(netdev->dev.parent,
 							LINK_TIMEOUT);
@@ -4551,20 +4553,14 @@ static void e1000_watchdog_task(struct work_struct *work)
 	adapter->gotc_old = adapter->stats.gotc;
 	spin_unlock(&adapter->stats64_lock);
 
-	e1000e_update_adaptive(&adapter->hw);
-
-	if (!netif_carrier_ok(netdev) &&
-	    (e1000_desc_unused(tx_ring) + 1 < tx_ring->count)) {
-		/* We've lost link, so the controller stops DMA,
-		 * but we've got queued Tx work that's never going
-		 * to get done, so reset controller to flush Tx.
-		 * (Do the reset outside of interrupt context).
-		 */
+	if (adapter->flags & FLAG_RESTART_NOW) {
 		schedule_work(&adapter->reset_task);
 		/* return immediately since reset is imminent */
 		return;
 	}
 
+	e1000e_update_adaptive(&adapter->hw);
+
 	/* Simple mode for Interrupt Throttle Rate (ITR) */
 	if (adapter->itr_setting == 4) {
 		/* Symmetric Tx/Rx gets a reduced ITR=2000;
@@ -4918,12 +4914,11 @@ static int e1000_transfer_dhcp_info(struct e1000_adapter *adapter,
 	struct e1000_hw *hw =  &adapter->hw;
 	u16 length, offset;
 
-	if (vlan_tx_tag_present(skb)) {
-		if (!((vlan_tx_tag_get(skb) == adapter->hw.mng_cookie.vlan_id) &&
-		    (adapter->hw.mng_cookie.status &
-			E1000_MNG_DHCP_COOKIE_STATUS_VLAN)))
-			return 0;
-	}
+	if (vlan_tx_tag_present(skb) &&
+	    !((vlan_tx_tag_get(skb) == adapter->hw.mng_cookie.vlan_id) &&
+	      (adapter->hw.mng_cookie.status &
+	       E1000_MNG_DHCP_COOKIE_STATUS_VLAN)))
+		return 0;
 
 	if (skb->len <= MINIMUM_DHCP_PACKET_SIZE)
 		return 0;
@@ -5134,10 +5129,9 @@ static void e1000_reset_task(struct work_struct *work)
 	if (test_bit(__E1000_DOWN, &adapter->state))
 		return;
 
-	if (!((adapter->flags & FLAG_RX_NEEDS_RESTART) &&
-	      (adapter->flags & FLAG_RX_RESTART_NOW))) {
+	if (!(adapter->flags & FLAG_RESTART_NOW)) {
 		e1000e_dump(adapter);
-		e_err("Reset adapter\n");
+		e_err("Reset adapter unexpectedly\n");
 	}
 	e1000e_reinit_locked(adapter);
 }

drivers/net/ethernet/intel/e1000e/nvm.c

@@ -359,7 +359,7 @@ s32 e1000e_read_nvm_eerd(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
 s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
 {
 	struct e1000_nvm_info *nvm = &hw->nvm;
-	s32 ret_val;
+	s32 ret_val = -E1000_ERR_NVM;
 	u16 widx = 0;
 
 	/* A check for invalid values:  offset too large, too many words,
@@ -371,16 +371,18 @@ s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
 		return -E1000_ERR_NVM;
 	}
 
-	ret_val = nvm->ops.acquire(hw);
-	if (ret_val)
-		return ret_val;
-
 	while (widx < words) {
 		u8 write_opcode = NVM_WRITE_OPCODE_SPI;
 
-		ret_val = e1000_ready_nvm_eeprom(hw);
+		ret_val = nvm->ops.acquire(hw);
 		if (ret_val)
-			goto release;
+			return ret_val;
+
+		ret_val = e1000_ready_nvm_eeprom(hw);
+		if (ret_val) {
+			nvm->ops.release(hw);
+			return ret_val;
+		}
 
 		e1000_standby_nvm(hw);
 
@@ -413,12 +415,10 @@ s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
 				break;
 			}
 		}
+		usleep_range(10000, 20000);
+		nvm->ops.release(hw);
 	}
 
-	usleep_range(10000, 20000);
-release:
-	nvm->ops.release(hw);
-
 	return ret_val;
 }
 
@@ -464,8 +464,8 @@ s32 e1000_read_pba_string_generic(struct e1000_hw *hw, u8 *pba_num,
 	if (nvm_data != NVM_PBA_PTR_GUARD) {
 		e_dbg("NVM PBA number is not stored as string\n");
 
-		/* we will need 11 characters to store the PBA */
-		if (pba_num_size < 11) {
+		/* make sure callers buffer is big enough to store the PBA */
+		if (pba_num_size < E1000_PBANUM_LENGTH) {
 			e_dbg("PBA string buffer too small\n");
 			return E1000_ERR_NO_SPACE;
 		}

drivers/net/ethernet/intel/e1000e/param.c

@@ -447,8 +447,7 @@ void e1000e_check_options(struct e1000_adapter *adapter)
 		if (num_SmartPowerDownEnable > bd) {
 			unsigned int spd = SmartPowerDownEnable[bd];
 			e1000_validate_option(&spd, &opt, adapter);
-			if ((adapter->flags & FLAG_HAS_SMART_POWER_DOWN)
-			    && spd)
+			if ((adapter->flags & FLAG_HAS_SMART_POWER_DOWN) && spd)
 				adapter->flags |= FLAG_SMART_POWER_DOWN;
 		}
 	}