Merge tag 'imx-dt64-5.16' of...

Merge tag 'imx-dt64-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt

i.MX arm64 device tree changes for 5.16:

- New board support: LX2160A based BlueBox3, S32G2 EVB and RDB2 boards.
- Quite some updates on imx8mq-librem5 board: delay the startup of the
  SDIO, add power sequencing for M.2 cards, add wifi regulator, add
  panel reset GPIO, fix led_r and led_g pinctrl, etc.
- Fix the SPI chipselect polarity for a couple of i.MX8MM boards.
- Add GPU nodes for i.MX8MM 2D and 3D core.
- Add VPU and DISP blk-ctrl devices for i.MX8MM.
- A series from Michael Walle to LS1028A device trees and add GPU
  support.
- Random and small updates on various boards.

* tag 'imx-dt64-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (37 commits)
  arm64: dts: imx8mm-kontron: Add support for ultra high speed modes on SD card
  arm64: dts: imx8mm-venice-gw7901.dts: disable pgc_gpumix
  arm64: dts: imx8mq-librem5: set debounce interval of volume buttons to 50ms
  arm64: dts: imx8mq-librem5: Limit the max sdio frequency
  arm64: dts: imx8mq-librem5: add power sequencing for M.2 cards
  arm64: dts: imx8mq-librem5: delay the startup of the SDIO
  arm64: dts: imx8mq-librem5: wire up the wifi regulator
  arm64: dts: imx8mq-librem5: Fix led_r and led_g pinctrl assignments
  arm64: dts: imx8mq-librem5: add reset gpio to mantix panel description
  arm64: dts: imx8mm-kontron: Fix reset delays for ethernet PHY
  arm64: dts: imx8mm: add DISP blk-ctrl
  arm64: dts: imx8mm: add VPU blk-ctrl
  arm64: dts: imx8mm: Add GPU nodes for 2D and 3D core
  arm64: dts: imx8mm: put USB controllers into power-domains
  arm64: dts: imx8mm: add GPC node
  arm64: dts: ls1028a: mark internal links between Felix and ENETC as capable of flow control
  arm64: dts: freescale: Fix 'interrupt-map' parent address cells
  arm64: dts: ls1028a: use phy-mode instead of phy-connection-type
  arm64: dts: ls1028a: move PHY nodes to MDIO controller
  arm64: dts: ls1028a: disable usb controller by default
  ...

Link: https://lore.kernel.org/r/20211016140138.1603-4-shawnguo@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

arch/arm64/boot/dts/freescale/Makefile

@@ -25,6 +25,8 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3-rev-a.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-clearfog-cx.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-honeycomb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
@@ -70,4 +72,6 @@ dtb-$(CONFIG_ARCH_MXC) += imx8qxp-ai_ml.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qxp-colibri-eval-v3.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
 
+dtb-$(CONFIG_ARCH_S32) += s32g274a-evb.dtb
+dtb-$(CONFIG_ARCH_S32) += s32g274a-rdb2.dtb
 dtb-$(CONFIG_ARCH_S32) += s32v234-evb.dtb

arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts

@@ -15,6 +15,7 @@ / {
 	compatible = "fsl,ls1012a-rdb", "fsl,ls1012a";
 
 	aliases {
+		serial0 = &duart0;
 		mmc0 = &esdhc0;
 		mmc1 = &esdhc1;
 	};

arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var1.dts

@@ -8,7 +8,7 @@
  * None of the  four SerDes lanes are used by the module, instead they are
  * all led out to the carrier for customer use.
  *
- * Copyright (C) 2020 Michael Walle <michael@walle.cc>
+ * Copyright (C) 2021 Michael Walle <michael@walle.cc>
  *
  */
 
@@ -21,43 +21,39 @@ / {
 	compatible = "kontron,sl28-var1", "kontron,sl28", "fsl,ls1028a";
 };
 
+&enetc_mdio_pf3 {
+	/* Delete unused phy node */
+	/delete-node/ ethernet-phy@5;
+
+	phy0: ethernet-phy@4 {
+		reg = <0x4>;
+		eee-broken-1000t;
+		eee-broken-100tx;
+		qca,clk-out-frequency = <125000000>;
+		qca,clk-out-strength = <AR803X_STRENGTH_FULL>;
+		qca,keep-pll-enabled;
+		vddio-supply = <&vddio>;
+
+		vddio: vddio-regulator {
+			regulator-name = "VDDIO";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vddh: vddh-regulator {
+			regulator-name = "VDDH";
+		};
+	};
+};
+
 &enetc_port0 {
 	status = "disabled";
-	/*
-	 * Delete both the phy-handle to the old phy0 label as well as
-	 * the mdio node with the old phy node with the old phy0 label.
-	 */
+	/* Delete the phy-handle to the old phy0 label */
 	/delete-property/ phy-handle;
-	/delete-node/ mdio;
 };
 
 &enetc_port1 {
 	phy-handle = <&phy0>;
-	phy-connection-type = "rgmii-id";
+	phy-mode = "rgmii-id";
 	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		phy0: ethernet-phy@4 {
-			reg = <0x4>;
-			eee-broken-1000t;
-			eee-broken-100tx;
-			qca,clk-out-frequency = <125000000>;
-			qca,clk-out-strength = <AR803X_STRENGTH_FULL>;
-			qca,keep-pll-enabled;
-			vddio-supply = <&vddio>;
-
-			vddio: vddio-regulator {
-				regulator-name = "VDDIO";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-			};
-
-			vddh: vddh-regulator {
-				regulator-name = "VDDH";
-			};
-		};
-	};
 };

arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var2.dts

@@ -5,7 +5,7 @@
  * This is for the network variant 2 which has two ethernet ports. These
  * ports are connected to the internal switch.
  *
- * Copyright (C) 2020 Michael Walle <michael@walle.cc>
+ * Copyright (C) 2021 Michael Walle <michael@walle.cc>
  *
  */
 
@@ -18,12 +18,6 @@ / {
 };
 
 &enetc_mdio_pf3 {
-	phy0: ethernet-phy@5 {
-		reg = <0x5>;
-		eee-broken-1000t;
-		eee-broken-100tx;
-	};
-
 	phy1: ethernet-phy@4 {
 		reg = <0x4>;
 		eee-broken-1000t;
@@ -34,14 +28,11 @@ phy1: ethernet-phy@4 {
 &enetc_port0 {
 	status = "disabled";
 	/*
-	 * In the base device tree the PHY was registered in the mdio
-	 * subnode as it is PHY for this port. On this module this PHY
-	 * is connected to a switch port instead and registered above.
-	 * Therefore, delete the mdio subnode as well as the phy-handle
-	 * property here.
+	 * In the base device tree the PHY at address 5 was assigned for
+	 * this port. On this module this PHY is connected to a switch
+	 * port instead. Therefore, delete the phy-handle property here.
 	 */
 	/delete-property/ phy-handle;
-	/delete-node/ mdio;
 };
 
 &enetc_port2 {

arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var4.dts

@@ -5,7 +5,7 @@
  * This is for the network variant 4 which has two ethernet ports. It
  * extends the base and provides one more port connected via RGMII.
  *
- * Copyright (C) 2019 Michael Walle <michael@walle.cc>
+ * Copyright (C) 2021 Michael Walle <michael@walle.cc>
  *
  */
 
@@ -18,33 +18,30 @@ / {
 	compatible = "kontron,sl28-var4", "kontron,sl28", "fsl,ls1028a";
 };
 
-&enetc_port1 {
-	phy-handle = <&phy1>;
-	phy-connection-type = "rgmii-id";
-	status = "okay";
+&enetc_mdio_pf3 {
+	phy1: ethernet-phy@4 {
+		reg = <0x4>;
+		eee-broken-1000t;
+		eee-broken-100tx;
+		qca,clk-out-frequency = <125000000>;
+		qca,clk-out-strength = <AR803X_STRENGTH_FULL>;
+		qca,keep-pll-enabled;
+		vddio-supply = <&vddio>;
 
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		phy1: ethernet-phy@4 {
-			reg = <0x4>;
-			eee-broken-1000t;
-			eee-broken-100tx;
-			qca,clk-out-frequency = <125000000>;
-			qca,clk-out-strength = <AR803X_STRENGTH_FULL>;
-			qca,keep-pll-enabled;
-			vddio-supply = <&vddio>;
-
-			vddio: vddio-regulator {
-				regulator-name = "VDDIO";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-			};
+		vddio: vddio-regulator {
+			regulator-name = "VDDIO";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
 
-			vddh: vddh-regulator {
-				regulator-name = "VDDH";
-			};
+		vddh: vddh-regulator {
+			regulator-name = "VDDH";
 		};
 	};
 };
+
+&enetc_port1 {
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+};

arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts

@@ -2,7 +2,7 @@
 /*
  * Device Tree file for the Kontron SMARC-sAL28 board.
  *
- * Copyright (C) 2019 Michael Walle <michael@walle.cc>
+ * Copyright (C) 2021 Michael Walle <michael@walle.cc>
  *
  */
 
@@ -80,22 +80,19 @@ &duart1 {
 	status = "okay";
 };
 
+&enetc_mdio_pf3 {
+	phy0: ethernet-phy@5 {
+		reg = <0x5>;
+		eee-broken-1000t;
+		eee-broken-100tx;
+	};
+};
+
 &enetc_port0 {
 	phy-handle = <&phy0>;
-	phy-connection-type = "sgmii";
+	phy-mode = "sgmii";
 	managed = "in-band-status";
 	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		phy0: ethernet-phy@5 {
-			reg = <0x5>;
-			eee-broken-1000t;
-			eee-broken-100tx;
-		};
-	};
 };
 
 &esdhc {
@@ -309,3 +306,11 @@ eeprom@50 {
 &lpuart1 {
 	status = "okay";
 };
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};

arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts

@@ -320,7 +320,7 @@ mux: mux-controller {
 
 &enetc_port1 {
 	phy-handle = <&qds_phy1>;
-	phy-connection-type = "rgmii-id";
+	phy-mode = "rgmii-id";
 	status = "okay";
 };
 
@@ -335,3 +335,11 @@ &sai1 {
 &sata {
 	status = "okay";
 };
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};

arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts

@@ -197,6 +197,10 @@ &duart1 {
 };
 
 &enetc_mdio_pf3 {
+	sgmii_phy0: ethernet-phy@2 {
+		reg = <0x2>;
+	};
+
 	/* VSC8514 QSGMII quad PHY */
 	qsgmii_phy0: ethernet-phy@10 {
 		reg = <0x10>;
@@ -217,17 +221,9 @@ qsgmii_phy3: ethernet-phy@13 {
 
 &enetc_port0 {
 	phy-handle = <&sgmii_phy0>;
-	phy-connection-type = "sgmii";
+	phy-mode = "sgmii";
 	managed = "in-band-status";
 	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		sgmii_phy0: ethernet-phy@2 {
-			reg = <0x2>;
-		};
-	};
 };
 
 &enetc_port2 {
@@ -287,6 +283,11 @@ &sata {
 	status = "okay";
 };
 
+&usb0 {
+	status = "okay";
+};
+
 &usb1 {
 	dr_mode = "otg";
+	status = "okay";
 };

arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi

@@ -80,13 +80,6 @@ osc_27m: clock-osc-27m {
 		clock-output-names = "phy_27m";
 	};
 
-	dpclk: clock-controller@f1f0000 {
-		compatible = "fsl,ls1028a-plldig";
-		reg = <0x0 0xf1f0000 0x0 0xffff>;
-		#clock-cells = <0>;
-		clocks = <&osc_27m>;
-	};
-
 	firmware {
 		optee: optee  {
 			compatible = "linaro,optee-tz";
@@ -592,6 +585,7 @@ usb0: usb@3100000 {
 			snps,dis_rxdet_inp3_quirk;
 			snps,quirk-frame-length-adjustment = <0x20>;
 			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+			status = "disabled";
 		};
 
 		usb1: usb@3110000 {
@@ -602,6 +596,7 @@ usb1: usb@3110000 {
 			snps,dis_rxdet_inp3_quirk;
 			snps,quirk-frame-length-adjustment = <0x20>;
 			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+			status = "disabled";
 		};
 
 		sata: sata@3200000 {
@@ -800,6 +795,38 @@ QORIQ_CLK_PLL_DIV(16)>,
 			clock-names = "wdog_clk", "apb_pclk";
 		};
 
+		malidp0: display@f080000 {
+			compatible = "arm,mali-dp500";
+			reg = <0x0 0xf080000 0x0 0x10000>;
+			interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>,
+				     <0 223 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "DE", "SE";
+			clocks = <&dpclk>,
+				 <&clockgen QORIQ_CLK_HWACCEL 2>,
+				 <&clockgen QORIQ_CLK_HWACCEL 2>,
+				 <&clockgen QORIQ_CLK_HWACCEL 2>;
+			clock-names = "pxlclk", "mclk", "aclk", "pclk";
+			arm,malidp-output-port-lines = /bits/ 8 <8 8 8>;
+			arm,malidp-arqos-value = <0xd000d000>;
+
+			port {
+				dpi0_out: endpoint {
+
+				};
+			};
+		};
+
+		gpu: gpu@f0c0000 {
+			compatible = "vivante,gc";
+			reg = <0x0 0xf0c0000 0x0 0x10000>;
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen QORIQ_CLK_HWACCEL 2>,
+				 <&clockgen QORIQ_CLK_HWACCEL 2>,
+				 <&clockgen QORIQ_CLK_HWACCEL 2>;
+			clock-names = "core", "shader", "bus";
+			#cooling-cells = <2>;
+		};
+
 		sai1: audio-controller@f100000 {
 			#sound-dai-cells = <0>;
 			compatible = "fsl,vf610-sai";
@@ -926,6 +953,13 @@ QORIQ_CLK_PLL_DIV(2)>,
 			status = "disabled";
 		};
 
+		dpclk: clock-controller@f1f0000 {
+			compatible = "fsl,ls1028a-plldig";
+			reg = <0x0 0xf1f0000 0x0 0x10000>;
+			#clock-cells = <0>;
+			clocks = <&osc_27m>;
+		};
+
 		tmu: tmu@1f80000 {
 			compatible = "fsl,qoriq-tmu";
 			reg = <0x0 0x1f80000 0x0 0x10000>;
@@ -1025,6 +1059,7 @@ enetc_port2: ethernet@0,2 {
 				fixed-link {
 					speed = <2500>;
 					full-duplex;
+					pause;
 				};
 			};
 
@@ -1083,6 +1118,7 @@ mscc_felix_port4: port@4 {
 						fixed-link {
 							speed = <2500>;
 							full-duplex;
+							pause;
 						};
 					};
 
@@ -1094,6 +1130,7 @@ mscc_felix_port5: port@5 {
 						fixed-link {
 							speed = <1000>;
 							full-duplex;
+							pause;
 						};
 					};
 				};
@@ -1108,6 +1145,7 @@ enetc_port3: ethernet@0,6 {
 				fixed-link {
 					speed = <1000>;
 					full-duplex;
+					pause;
 				};
 			};
 
@@ -1139,24 +1177,4 @@ ftm_alarm0: timer@2800000 {
 		};
 	};
 
-	malidp0: display@f080000 {
-		compatible = "arm,mali-dp500";
-		reg = <0x0 0xf080000 0x0 0x10000>;
-		interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>,
-			     <0 223 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "DE", "SE";
-		clocks = <&dpclk>,
-			 <&clockgen QORIQ_CLK_HWACCEL 2>,
-			 <&clockgen QORIQ_CLK_HWACCEL 2>,
-			 <&clockgen QORIQ_CLK_HWACCEL 2>;
-		clock-names = "pxlclk", "mclk", "aclk", "pclk";
-		arm,malidp-output-port-lines = /bits/ 8 <8 8 8>;
-		arm,malidp-arqos-value = <0xd000d000>;
-
-		port {
-			dp0_out: endpoint {
-
-			};
-		};
-	};
 };

arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi

@@ -241,18 +241,18 @@ extirq: interrupt-controller@14 {
 				interrupt-controller;
 				reg = <0x14 4>;
 				interrupt-map =
-					<0 0 &gic GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
-					<1 0 &gic GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
-					<2 0 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
-					<3 0 &gic GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
-					<4 0 &gic GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
-					<5 0 &gic GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
-					<6 0 &gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
-					<7 0 &gic GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
-					<8 0 &gic GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
-					<9 0 &gic GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
-					<10 0 &gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
-					<11 0 &gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+					<0 0 &gic 0 0 GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+					<1 0 &gic 0 0 GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+					<2 0 &gic 0 0 GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+					<3 0 &gic 0 0 GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+					<4 0 &gic 0 0 GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+					<5 0 &gic 0 0 GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+					<6 0 &gic 0 0 GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+					<7 0 &gic 0 0 GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+					<8 0 &gic 0 0 GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					<9 0 &gic 0 0 GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+					<10 0 &gic 0 0 GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+					<11 0 &gic 0 0 GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-map-mask = <0xffffffff 0x0>;
 			};
 		};
@@ -847,7 +847,7 @@ pcs7_3: ethernet-phy@3 {
 		};
 
 		cluster1_core0_watchdog: wdt@c000000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc000000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -857,7 +857,7 @@ QORIQ_CLK_PLL_DIV(16)>,
 		};
 
 		cluster1_core1_watchdog: wdt@c010000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc010000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -867,7 +867,7 @@ QORIQ_CLK_PLL_DIV(16)>,
 		};
 
 		cluster1_core2_watchdog: wdt@c020000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc020000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -877,7 +877,7 @@ QORIQ_CLK_PLL_DIV(16)>,
 		};
 
 		cluster1_core3_watchdog: wdt@c030000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc030000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -887,7 +887,7 @@ QORIQ_CLK_PLL_DIV(16)>,
 		};
 
 		cluster2_core0_watchdog: wdt@c100000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc100000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -897,7 +897,7 @@ QORIQ_CLK_PLL_DIV(16)>,
 		};
 
 		cluster2_core1_watchdog: wdt@c110000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc110000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -907,7 +907,7 @@ QORIQ_CLK_PLL_DIV(16)>,
 		};
 
 		cluster2_core2_watchdog: wdt@c120000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc120000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -917,7 +917,7 @@ QORIQ_CLK_PLL_DIV(16)>,
 		};
 
 		cluster2_core3_watchdog: wdt@c130000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc130000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,

arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi

@@ -293,18 +293,18 @@ extirq: interrupt-controller@14 {
 				interrupt-controller;
 				reg = <0x14 4>;
 				interrupt-map =
-					<0 0 &gic GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
-					<1 0 &gic GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
-					<2 0 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
-					<3 0 &gic GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
-					<4 0 &gic GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
-					<5 0 &gic GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
-					<6 0 &gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
-					<7 0 &gic GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
-					<8 0 &gic GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
-					<9 0 &gic GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
-					<10 0 &gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
-					<11 0 &gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+					<0 0 &gic 0 0 GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+					<1 0 &gic 0 0 GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+					<2 0 &gic 0 0 GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+					<3 0 &gic 0 0 GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+					<4 0 &gic 0 0 GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+					<5 0 &gic 0 0 GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+					<6 0 &gic 0 0 GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+					<7 0 &gic 0 0 GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+					<8 0 &gic 0 0 GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					<9 0 &gic 0 0 GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+					<10 0 &gic 0 0 GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+					<11 0 &gic 0 0 GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-map-mask = <0xffffffff 0x0>;
 			};
 		};
@@ -387,7 +387,7 @@ serial3: serial@21d0600 {
 		};
 
 		cluster1_core0_watchdog: wdt@c000000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc000000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -397,7 +397,7 @@ QORIQ_CLK_PLL_DIV(4)>,
 		};
 
 		cluster1_core1_watchdog: wdt@c010000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc010000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -407,7 +407,7 @@ QORIQ_CLK_PLL_DIV(4)>,
 		};
 
 		cluster2_core0_watchdog: wdt@c100000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc100000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -417,7 +417,7 @@ QORIQ_CLK_PLL_DIV(4)>,
 		};
 
 		cluster2_core1_watchdog: wdt@c110000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc110000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -427,7 +427,7 @@ QORIQ_CLK_PLL_DIV(4)>,
 		};
 
 		cluster3_core0_watchdog: wdt@c200000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc200000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -437,7 +437,7 @@ QORIQ_CLK_PLL_DIV(4)>,
 		};
 
 		cluster3_core1_watchdog: wdt@c210000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc210000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -447,7 +447,7 @@ QORIQ_CLK_PLL_DIV(4)>,
 		};
 
 		cluster4_core0_watchdog: wdt@c300000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc300000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -457,7 +457,7 @@ QORIQ_CLK_PLL_DIV(4)>,
 		};
 
 		cluster4_core1_watchdog: wdt@c310000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc310000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,

arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts

+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Device Tree file for LX2160A BLUEBOX3
+//
+// Copyright 2020-2021 NXP
+
+/dts-v1/;
+
+#include "fsl-lx2160a-bluebox3.dts"
+
+/ {
+	compatible = "fsl,lx2160a-bluebox3-rev-a", "fsl,lx2160a";
+};
+
+/* The RGMII PHYs have a different MDIO address */
+&emdio1 {
+	/delete-node/ ethernet-phy@5;
+
+	sw1_mii3_phy: ethernet-phy@1 {
+		/* AR8035 */
+		compatible = "ethernet-phy-id004d.d072";
+		reg = <0x1>;
+		interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	/delete-node/ ethernet-phy@6;
+
+	sw2_mii3_phy: ethernet-phy@2 {
+		/* AR8035 */
+		compatible = "ethernet-phy-id004d.d072";
+		reg = <0x2>;
+		interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>;
+	};
+};

arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts

+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Device Tree file for LX2160A BLUEBOX3
+//
+// Copyright 2020-2021 NXP
+
+/dts-v1/;
+
+#include "fsl-lx2160a.dtsi"
+
+/ {
+	model = "NXP Layerscape LX2160ABLUEBOX3";
+	compatible = "fsl,lx2160a-bluebox3", "fsl,lx2160a";
+
+	aliases {
+		crypto = &crypto;
+		mmc0 = &esdhc0;
+		mmc1 = &esdhc1;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	sb_3v3: regulator-sb3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "MC34717-3.3VSB";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
+
+&can0 {
+	status = "okay";
+
+	can-transceiver {
+		max-bitrate = <5000000>;
+	};
+};
+
+&can1 {
+	status = "okay";
+
+	can-transceiver {
+		max-bitrate = <5000000>;
+	};
+};
+
+&crypto {
+	status = "okay";
+};
+
+&dpmac5 {
+	phy-handle = <&aqr113c_phy1>;
+	phy-mode = "usxgmii";
+	managed = "in-band-status";
+};
+
+&dpmac6 {
+	phy-handle = <&aqr113c_phy2>;
+	phy-mode = "usxgmii";
+	managed = "in-band-status";
+};
+
+&dpmac9 {
+	phy-handle = <&aqr113c_phy3>;
+	phy-mode = "usxgmii";
+	managed = "in-band-status";
+};
+
+&dpmac10 {
+	phy-handle = <&aqr113c_phy4>;
+	phy-mode = "usxgmii";
+	managed = "in-band-status";
+};
+
+&dpmac17 {
+	phy-mode = "rgmii";
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&dpmac18 {
+	phy-mode = "rgmii";
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&emdio1 {
+	status = "okay";
+
+	aqr113c_phy2: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <0x0>;
+		/* IRQ_10G_PHY2 */
+		interrupts-extended = <&extirq 3 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	aqr113c_phy1: ethernet-phy@8 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <0x8>;
+		/* IRQ_10G_PHY1 */
+		interrupts-extended = <&extirq 2 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	sw1_mii3_phy: ethernet-phy@5 {
+		/* AR8035 */
+		compatible = "ethernet-phy-id004d.d072";
+		reg = <0x5>;
+		interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	sw2_mii3_phy: ethernet-phy@6 {
+		/* AR8035 */
+		compatible = "ethernet-phy-id004d.d072";
+		reg = <0x6>;
+		interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&emdio2 {
+	status = "okay";
+
+	aqr113c_phy4: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <0x0>;
+		/* IRQ_10G_PHY4 */
+		interrupts-extended = <&extirq 5 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	aqr113c_phy3: ethernet-phy@8 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <0x8>;
+		/* IRQ_10G_PHY3 */
+		interrupts-extended = <&extirq 4 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&esdhc0 {
+	sd-uhs-sdr104;
+	sd-uhs-sdr50;
+	sd-uhs-sdr25;
+	sd-uhs-sdr12;
+	status = "okay";
+};
+
+&esdhc1 {
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	bus-width = <8>;
+	status = "okay";
+};
+
+&fspi {
+	status = "okay";
+
+	mt35xu512aba0: flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		m25p,fast-read;
+		spi-max-frequency = <50000000>;
+		spi-rx-bus-width = <8>;
+		spi-tx-bus-width = <8>;
+	};
+
+	mt35xu512aba1: flash@1 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <1>;
+		m25p,fast-read;
+		spi-max-frequency = <50000000>;
+		spi-rx-bus-width = <8>;
+		spi-tx-bus-width = <8>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	i2c-mux@77 {
+		compatible = "nxp,pca9547";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+
+			power-monitor@40 {
+				compatible = "ti,ina220";
+				reg = <0x40>;
+				shunt-resistor = <500>;
+			};
+		};
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+
+			temp2: temperature-sensor@48 {
+				compatible = "nxp,sa56004";
+				reg = <0x48>;
+				vcc-supply = <&sb_3v3>;
+				#thermal-sensor-cells = <1>;
+			};
+
+			temp1: temperature-sensor@4c {
+				compatible = "nxp,sa56004";
+				reg = <0x4c>;
+				vcc-supply = <&sb_3v3>;
+				#thermal-sensor-cells = <1>;
+			};
+		};
+
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+
+			rtc@51 {
+				compatible = "nxp,pcf2129";
+				reg = <0x51>;
+				interrupts-extended = <&extirq 11 IRQ_TYPE_LEVEL_LOW>;
+			};
+		};
+
+		i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x7>;
+
+			i2c-mux@75 {
+				compatible = "nxp,pca9547";
+				reg = <0x75>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x0>;
+
+					spi_bridge: spi@28 {
+						compatible = "nxp,sc18is602b";
+						reg = <0x28>;
+						#address-cells = <1>;
+						#size-cells = <0>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	i2c-mux@77 {
+		compatible = "nxp,pca9846";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+
+			/* The I2C multiplexer and temperature sensors are on
+			 * the T6 riser card.
+			 */
+			i2c-mux@70 {
+				compatible = "nxp,pca9548";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x6>;
+
+					q12: temperature-sensor@4c {
+						compatible = "nxp,sa56004";
+						reg = <0x4c>;
+						vcc-supply = <&sb_3v3>;
+						#thermal-sensor-cells = <1>;
+					};
+				};
+
+				i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x7>;
+
+					q11: temperature-sensor@4c {
+						compatible = "nxp,sa56004";
+						reg = <0x4c>;
+						vcc-supply = <&sb_3v3>;
+						#thermal-sensor-cells = <1>;
+					};
+
+					q13: temperature-sensor@48 {
+						compatible = "nxp,sa56004";
+						reg = <0x48>;
+						vcc-supply = <&sb_3v3>;
+						#thermal-sensor-cells = <1>;
+					};
+
+					q14: temperature-sensor@4a {
+						compatible = "nxp,sa56004";
+						reg = <0x4a>;
+						vcc-supply = <&sb_3v3>;
+						#thermal-sensor-cells = <1>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&pcs_mdio5 {
+	status = "okay";
+};
+
+&pcs_mdio6 {
+	status = "okay";
+};
+
+&pcs_mdio9 {
+	status = "okay";
+};
+
+&pcs_mdio10 {
+	status = "okay";
+};
+
+&spi_bridge {
+	sw1: ethernet-switch@0 {
+		compatible = "nxp,sja1110a";
+		reg = <0>;
+		spi-max-frequency = <4000000>;
+		spi-cpol;
+		dsa,member = <0 0>;
+
+		ethernet-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* Microcontroller port */
+			port@0 {
+				reg = <0>;
+				status = "disabled";
+			};
+
+			/* SW1_P1 */
+			port@1 {
+				reg = <1>;
+				label = "con_2x20";
+				phy-mode = "sgmii";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				ethernet = <&dpmac17>;
+				phy-mode = "rgmii-id";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "1ge_p1";
+				phy-mode = "rgmii-id";
+				phy-handle = <&sw1_mii3_phy>;
+			};
+
+			sw1p4: port@4 {
+				reg = <4>;
+				link = <&sw2p1>;
+				phy-mode = "sgmii";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "trx1";
+				phy-mode = "internal";
+				phy-handle = <&sw1_port5_base_t1_phy>;
+			};
+
+			port@6 {
+				reg = <6>;
+				label = "trx2";
+				phy-mode = "internal";
+				phy-handle = <&sw1_port6_base_t1_phy>;
+			};
+
+			port@7 {
+				reg = <7>;
+				label = "trx3";
+				phy-mode = "internal";
+				phy-handle = <&sw1_port7_base_t1_phy>;
+			};
+
+			port@8 {
+				reg = <8>;
+				label = "trx4";
+				phy-mode = "internal";
+				phy-handle = <&sw1_port8_base_t1_phy>;
+			};
+
+			port@9 {
+				reg = <9>;
+				label = "trx5";
+				phy-mode = "internal";
+				phy-handle = <&sw1_port9_base_t1_phy>;
+			};
+
+			port@a {
+				reg = <10>;
+				label = "trx6";
+				phy-mode = "internal";
+				phy-handle = <&sw1_port10_base_t1_phy>;
+			};
+		};
+
+		mdios {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			mdio@0 {
+				compatible = "nxp,sja1110-base-t1-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+
+				sw1_port5_base_t1_phy: ethernet-phy@1 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x1>;
+				};
+
+				sw1_port6_base_t1_phy: ethernet-phy@2 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x2>;
+				};
+
+				sw1_port7_base_t1_phy: ethernet-phy@3 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x3>;
+				};
+
+				sw1_port8_base_t1_phy: ethernet-phy@4 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x4>;
+				};
+
+				sw1_port9_base_t1_phy: ethernet-phy@5 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x5>;
+				};
+
+				sw1_port10_base_t1_phy: ethernet-phy@6 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x6>;
+				};
+			};
+		};
+	};
+
+	sw2: ethernet-switch@2 {
+		compatible = "nxp,sja1110a";
+		reg = <2>;
+		spi-max-frequency = <4000000>;
+		spi-cpol;
+		dsa,member = <0 1>;
+
+		ethernet-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* Microcontroller port */
+			port@0 {
+				reg = <0>;
+				status = "disabled";
+			};
+
+			sw2p1: port@1 {
+				reg = <1>;
+				link = <&sw1p4>;
+				phy-mode = "sgmii";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				ethernet = <&dpmac18>;
+				phy-mode = "rgmii-id";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "1ge_p2";
+				phy-mode = "rgmii-id";
+				phy-handle = <&sw2_mii3_phy>;
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "to_sw3";
+				phy-mode = "2500base-x";
+
+				fixed-link {
+					speed = <2500>;
+					full-duplex;
+				};
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "trx7";
+				phy-mode = "internal";
+				phy-handle = <&sw2_port5_base_t1_phy>;
+			};
+
+			port@6 {
+				reg = <6>;
+				label = "trx8";
+				phy-mode = "internal";
+				phy-handle = <&sw2_port6_base_t1_phy>;
+			};
+
+			port@7 {
+				reg = <7>;
+				label = "trx9";
+				phy-mode = "internal";
+				phy-handle = <&sw2_port7_base_t1_phy>;
+			};
+
+			port@8 {
+				reg = <8>;
+				label = "trx10";
+				phy-mode = "internal";
+				phy-handle = <&sw2_port8_base_t1_phy>;
+			};
+
+			port@9 {
+				reg = <9>;
+				label = "trx11";
+				phy-mode = "internal";
+				phy-handle = <&sw2_port9_base_t1_phy>;
+			};
+
+			port@a {
+				reg = <10>;
+				label = "trx12";
+				phy-mode = "internal";
+				phy-handle = <&sw2_port10_base_t1_phy>;
+			};
+		};
+
+		mdios {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			mdio@0 {
+				compatible = "nxp,sja1110-base-t1-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+
+				sw2_port5_base_t1_phy: ethernet-phy@1 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x1>;
+				};
+
+				sw2_port6_base_t1_phy: ethernet-phy@2 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x2>;
+				};
+
+				sw2_port7_base_t1_phy: ethernet-phy@3 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x3>;
+				};
+
+				sw2_port8_base_t1_phy: ethernet-phy@4 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x4>;
+				};
+
+				sw2_port9_base_t1_phy: ethernet-phy@5 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x5>;
+				};
+
+				sw2_port10_base_t1_phy: ethernet-phy@6 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x6>;
+				};
+			};
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};

arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi

@@ -680,18 +680,18 @@ extirq: interrupt-controller@14 {
 				interrupt-controller;
 				reg = <0x14 4>;
 				interrupt-map =
-					<0 0 &gic GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
-					<1 0 &gic GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
-					<2 0 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
-					<3 0 &gic GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
-					<4 0 &gic GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
-					<5 0 &gic GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
-					<6 0 &gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
-					<7 0 &gic GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
-					<8 0 &gic GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
-					<9 0 &gic GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
-					<10 0 &gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
-					<11 0 &gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+					<0 0 &gic 0 0 GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+					<1 0 &gic 0 0 GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+					<2 0 &gic 0 0 GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+					<3 0 &gic 0 0 GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+					<4 0 &gic 0 0 GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+					<5 0 &gic 0 0 GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+					<6 0 &gic 0 0 GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+					<7 0 &gic 0 0 GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+					<8 0 &gic 0 0 GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					<9 0 &gic 0 0 GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+					<10 0 &gic 0 0 GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+					<11 0 &gic 0 0 GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-map-mask = <0xffffffff 0x0>;
 			};
 		};

arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts

@@ -121,8 +121,8 @@ mdio {
 
 		ethphy: ethernet-phy@0 {
 			reg = <0>;
-			reset-assert-us = <100>;
-			reset-deassert-us = <100>;
+			reset-assert-us = <1>;
+			reset-deassert-us = <15000>;
 			reset-gpios = <&gpio4 27 GPIO_ACTIVE_LOW>;
 		};
 	};
@@ -189,8 +189,10 @@ usbnet: usbether@1 {
 };
 
 &usdhc2 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
 	vmmc-supply = <&reg_vdd_3v3>;
 	vqmmc-supply = <&reg_nvcc_sd>;
 	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
@@ -319,4 +321,28 @@ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
 			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
 		>;
 	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x194
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x196
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+		>;
+	};
 };

arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi

@@ -63,7 +63,7 @@ opp-750M {
 &ecspi1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
-	cs-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	spi-flash@0 {
@@ -86,6 +86,7 @@ pca9450: pmic@25 {
 		pinctrl-0 = <&pinctrl_pmic>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
 
 		regulators {
 			reg_vdd_soc: BUCK1 {
@@ -225,6 +226,7 @@ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
 	pinctrl_pmic: pmicgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x141
+			MX8MM_IOMUXC_GPIO1_IO04_GPIO1_IO4		0x141
 		>;
 	};
 

arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi

@@ -57,7 +57,7 @@ reg_usb_otg1_vbus: regulator-usb-otg1 {
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_spi2>;
-	cs-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 

arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi

@@ -76,7 +76,7 @@ reg_usb_otg2_vbus: regulator-usb-otg2 {
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_spi2>;
-	cs-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 

arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi

@@ -96,7 +96,7 @@ reg_wifi_en: regulator-wifi-en {
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_spi2>;
-	cs-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 

arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts

@@ -255,6 +255,10 @@ opp-750M {
 	};
 };
 
+&disp_blk_ctrl {
+	status = "disabled";
+};
+
 &ecspi1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_spi1>;
@@ -282,6 +286,14 @@ fixed-link {
 	};
 };
 
+&gpu_2d {
+	status = "disabled";
+};
+
+&gpu_3d {
+	status = "disabled";
+};
+
 &i2c1 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default";
@@ -632,6 +644,18 @@ &i2c4 {
 	status = "okay";
 };
 
+&pgc_gpu {
+	status = "disabled";
+};
+
+&pgc_gpumix {
+	status = "disabled";
+};
+
+&pgc_mipi {
+	status = "disabled";
+};
+
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>, <&pinctrl_uart1_gpio>;

arch/arm64/boot/dts/freescale/imx8mm.dtsi

@@ -7,6 +7,8 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/imx8mm-power.h>
+#include <dt-bindings/reset/imx8mq-reset.h>
 #include <dt-bindings/thermal/thermal.h>
 
 #include "imx8mm-pinfunc.h"
@@ -610,6 +612,111 @@ src: reset-controller@30390000 {
 				interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 				#reset-cells = <1>;
 			};
+
+			gpc: gpc@303a0000 {
+				compatible = "fsl,imx8mm-gpc";
+				reg = <0x303a0000 0x10000>;
+				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&gic>;
+				interrupt-controller;
+				#interrupt-cells = <3>;
+
+				pgc {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					pgc_hsiomix: power-domain@0 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_HSIOMIX>;
+						clocks = <&clk IMX8MM_CLK_USB_BUS>;
+						assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>;
+						assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>;
+					};
+
+					pgc_pcie: power-domain@1 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_PCIE>;
+						power-domains = <&pgc_hsiomix>;
+						clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>;
+					};
+
+					pgc_otg1: power-domain@2 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_OTG1>;
+						power-domains = <&pgc_hsiomix>;
+					};
+
+					pgc_otg2: power-domain@3 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_OTG2>;
+						power-domains = <&pgc_hsiomix>;
+					};
+
+					pgc_gpumix: power-domain@4 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_GPUMIX>;
+						clocks = <&clk IMX8MM_CLK_GPU_BUS_ROOT>,
+							 <&clk IMX8MM_CLK_GPU_AHB>;
+						assigned-clocks = <&clk IMX8MM_CLK_GPU_AXI>,
+								  <&clk IMX8MM_CLK_GPU_AHB>;
+						assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_800M>,
+									 <&clk IMX8MM_SYS_PLL1_800M>;
+						assigned-clock-rates = <800000000>, <400000000>;
+					};
+
+					pgc_gpu: power-domain@5 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_GPU>;
+						clocks = <&clk IMX8MM_CLK_GPU_AHB>,
+							 <&clk IMX8MM_CLK_GPU_BUS_ROOT>,
+							 <&clk IMX8MM_CLK_GPU2D_ROOT>,
+							 <&clk IMX8MM_CLK_GPU3D_ROOT>;
+						resets = <&src IMX8MQ_RESET_GPU_RESET>;
+						power-domains = <&pgc_gpumix>;
+					};
+
+					pgc_vpumix: power-domain@6 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_VPUMIX>;
+						clocks = <&clk IMX8MM_CLK_VPU_DEC_ROOT>;
+						assigned-clocks = <&clk IMX8MM_CLK_VPU_BUS>;
+						assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_800M>;
+						resets = <&src IMX8MQ_RESET_VPU_RESET>;
+					};
+
+					pgc_vpu_g1: power-domain@7 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_VPUG1>;
+					};
+
+					pgc_vpu_g2: power-domain@8 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_VPUG2>;
+					};
+
+					pgc_vpu_h1: power-domain@9 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_VPUH1>;
+					};
+
+					pgc_dispmix: power-domain@10 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_DISPMIX>;
+						clocks = <&clk IMX8MM_CLK_DISP_APB_ROOT>,
+							 <&clk IMX8MM_CLK_DISP_AXI_ROOT>;
+						assigned-clocks = <&clk IMX8MM_CLK_DISP_AXI>,
+								  <&clk IMX8MM_CLK_DISP_APB>;
+						assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_1000M>,
+									 <&clk IMX8MM_SYS_PLL1_800M>;
+						assigned-clock-rates = <500000000>, <200000000>;
+					};
+
+					pgc_mipi: power-domain@11 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_MIPI>;
+					};
+				};
+			};
 		};
 
 		aips2: bus@30400000 {
@@ -961,6 +1068,33 @@ aips4: bus@32c00000 {
 			#size-cells = <1>;
 			ranges = <0x32c00000 0x32c00000 0x400000>;
 
+			disp_blk_ctrl: blk-ctrl@32e28000 {
+				compatible = "fsl,imx8mm-disp-blk-ctrl", "syscon";
+				reg = <0x32e28000 0x100>;
+				power-domains = <&pgc_dispmix>, <&pgc_dispmix>,
+						<&pgc_dispmix>, <&pgc_mipi>,
+						<&pgc_mipi>;
+				power-domain-names = "bus", "csi-bridge",
+						     "lcdif", "mipi-dsi",
+						     "mipi-csi";
+				clocks = <&clk IMX8MM_CLK_DISP_AXI_ROOT>,
+					 <&clk IMX8MM_CLK_DISP_APB_ROOT>,
+					 <&clk IMX8MM_CLK_CSI1_ROOT>,
+					 <&clk IMX8MM_CLK_DISP_AXI_ROOT>,
+					 <&clk IMX8MM_CLK_DISP_APB_ROOT>,
+					 <&clk IMX8MM_CLK_DISP_ROOT>,
+					 <&clk IMX8MM_CLK_DSI_CORE>,
+					 <&clk IMX8MM_CLK_DSI_PHY_REF>,
+					 <&clk IMX8MM_CLK_CSI1_CORE>,
+					 <&clk IMX8MM_CLK_CSI1_PHY_REF>;
+				clock-names = "csi-bridge-axi","csi-bridge-apb",
+					      "csi-bridge-core", "lcdif-axi",
+					      "lcdif-apb", "lcdif-pix",
+					      "dsi-pclk", "dsi-ref",
+					      "csi-aclk", "csi-pclk";
+				#power-domain-cells = <1>;
+			};
+
 			usbotg1: usb@32e40000 {
 				compatible = "fsl,imx8mm-usb", "fsl,imx7d-usb";
 				reg = <0x32e40000 0x200>;
@@ -971,6 +1105,7 @@ usbotg1: usb@32e40000 {
 				assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>;
 				phys = <&usbphynop1>;
 				fsl,usbmisc = <&usbmisc1 0>;
+				power-domains = <&pgc_otg1>;
 				status = "disabled";
 			};
 
@@ -990,6 +1125,7 @@ usbotg2: usb@32e50000 {
 				assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>;
 				phys = <&usbphynop2>;
 				fsl,usbmisc = <&usbmisc2 0>;
+				power-domains = <&pgc_otg2>;
 				status = "disabled";
 			};
 
@@ -1030,6 +1166,50 @@ gpmi: nand-controller@33002000{
 			status = "disabled";
 		};
 
+		gpu_3d: gpu@38000000 {
+			compatible = "vivante,gc";
+			reg = <0x38000000 0x8000>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk IMX8MM_CLK_GPU_AHB>,
+				 <&clk IMX8MM_CLK_GPU_BUS_ROOT>,
+				 <&clk IMX8MM_CLK_GPU3D_ROOT>,
+				 <&clk IMX8MM_CLK_GPU3D_ROOT>;
+			clock-names = "reg", "bus", "core", "shader";
+			assigned-clocks = <&clk IMX8MM_CLK_GPU3D_CORE>,
+					  <&clk IMX8MM_GPU_PLL_OUT>;
+			assigned-clock-parents = <&clk IMX8MM_GPU_PLL_OUT>;
+			assigned-clock-rates = <0>, <1000000000>;
+			power-domains = <&pgc_gpu>;
+		};
+
+		gpu_2d: gpu@38008000 {
+			compatible = "vivante,gc";
+			reg = <0x38008000 0x8000>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk IMX8MM_CLK_GPU_AHB>,
+				 <&clk IMX8MM_CLK_GPU_BUS_ROOT>,
+				 <&clk IMX8MM_CLK_GPU2D_ROOT>;
+			clock-names = "reg", "bus", "core";
+			assigned-clocks = <&clk IMX8MM_CLK_GPU2D_CORE>,
+					  <&clk IMX8MM_GPU_PLL_OUT>;
+			assigned-clock-parents = <&clk IMX8MM_GPU_PLL_OUT>;
+			assigned-clock-rates = <0>, <1000000000>;
+			power-domains = <&pgc_gpu>;
+		};
+
+		vpu_blk_ctrl: blk-ctrl@38330000 {
+			compatible = "fsl,imx8mm-vpu-blk-ctrl", "syscon";
+			reg = <0x38330000 0x100>;
+			power-domains = <&pgc_vpumix>, <&pgc_vpu_g1>,
+					<&pgc_vpu_g2>, <&pgc_vpu_h1>;
+			power-domain-names = "bus", "g1", "g2", "h1";
+			clocks = <&clk IMX8MM_CLK_VPU_G1_ROOT>,
+				 <&clk IMX8MM_CLK_VPU_G2_ROOT>,
+				 <&clk IMX8MM_CLK_VPU_H1_ROOT>;
+			clock-names = "g1", "g2", "h1";
+			#power-domain-cells = <1>;
+		};
+
 		gic: interrupt-controller@38800000 {
 			compatible = "arm,gic-v3";
 			reg = <0x38800000 0x10000>, /* GIC Dist */

arch/arm64/boot/dts/freescale/imx8mp.dtsi

@@ -785,7 +785,7 @@ flexspi: spi@30bb0000 {
 				interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clk IMX8MP_CLK_QSPI_ROOT>,
 					 <&clk IMX8MP_CLK_QSPI_ROOT>;
-				clock-names = "fspi", "fspi_en";
+				clock-names = "fspi_en", "fspi";
 				assigned-clock-rates = <80000000>;
 				assigned-clocks = <&clk IMX8MP_CLK_QSPI>;
 				#address-cells = <1>;

arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi

@@ -40,12 +40,14 @@ vol-down {
 			label = "VOL_DOWN";
 			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <50>;
 		};
 
 		vol-up {
 			label = "VOL_UP";
 			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <50>;
 		};
 	};
 
@@ -138,9 +140,14 @@ reg_vsys_3v4: regulator-vsys-3v4 {
 
 	reg_wifi_3v3: regulator-wifi-3v3 {
 		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_pwr>;
 		regulator-name = "3V3_WIFI";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 10 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&reg_vdd_3v3>;
 	};
 
 	sound {
@@ -193,6 +200,14 @@ simple-audio-card,codec {
 		};
 	};
 
+	usdhc2_pwrseq: pwrseq {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_bt>, <&pinctrl_wifi_disable>;
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>,
+			      <&gpio4 29 GPIO_ACTIVE_HIGH>;
+	};
+
 	bm818_codec: sound-wwan-codec {
 		compatible = "broadmobi,bm818", "option,gtm601";
 		#sound-dai-cells = <0>;
@@ -225,7 +240,7 @@ &A53_3 {
 &ddrc {
 	operating-points-v2 = <&ddrc_opp_table>;
 
-	ddrc_opp_table: ddrc-opp-table {
+	ddrc_opp_table: opp-table {
 		compatible = "operating-points-v2";
 
 		opp-25M {
@@ -307,6 +322,13 @@ MX8MQ_IOMUXC_NAND_DQS_GPIO3_IO14	0x83
 		>;
 	};
 
+	pinctrl_bt: btgrp {
+		fsl,pins = <
+			/* BT_REG_ON */
+			MX8MQ_IOMUXC_SAI5_MCLK_GPIO3_IO25	0x83
+		>;
+	};
+
 	pinctrl_charger_in: chargeringrp {
 		fsl,pins = <
 			/* CHRG_INT */
@@ -638,6 +660,20 @@ MX8MQ_IOMUXC_SD2_RESET_B_USDHC2_RESET_B 0xc1
 		>;
 	};
 
+	pinctrl_wifi_disable: wifidisablegrp {
+		fsl,pins = <
+			/* WIFI_REG_ON */
+			MX8MQ_IOMUXC_SAI3_RXC_GPIO4_IO29	0x83
+		>;
+	};
+
+	pinctrl_wifi_pwr: wifipwrgrp {
+		fsl,pins = <
+			/* WIFI3V3_EN */
+			MX8MQ_IOMUXC_NAND_DATA04_GPIO3_IO10	0x83
+		>;
+	};
+
 	pinctrl_wdog: wdoggrp {
 		fsl,pins = <
 			/* nWDOG */
@@ -1010,6 +1046,7 @@ lcd_panel: panel@0 {
 		vddi-supply = <&reg_lcd_1v8>;
 		backlight = <&backlight_dsi>;
 		reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
+		mantix,tp-rstn-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
 
 		port {
 			panel_in: endpoint {
@@ -1055,13 +1092,13 @@ &pwm2 {
 
 &pwm3 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_led_g>;
+	pinctrl-0 = <&pinctrl_led_r>;
 	status = "okay";
 };
 
 &pwm4 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_led_r>;
+	pinctrl-0 = <&pinctrl_led_g>;
 	status = "okay";
 };
 
@@ -1199,7 +1236,10 @@ &usdhc2 {
 	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
 	bus-width = <4>;
 	vmmc-supply = <&reg_wifi_3v3>;
+	mmc-pwrseq = <&usdhc2_pwrseq>;
+	post-power-on-delay-ms = <1000>;
 	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	max-frequency = <50000000>;
 	disable-wp;
 	cap-sdio-irq;
 	keep-power-in-suspend;

arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts

@@ -202,6 +202,7 @@ MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX		0x45
 
 	pinctrl_usdhc2: usdhc2grp {
 		fsl,pins = <
+			MX8MQ_IOMUXC_SD2_CD_B_USDHC2_CD_B		0x0
 			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x83
 			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xc3
 			MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xc3

arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi

@@ -555,6 +555,7 @@ &pcie0 {
 	         <&clk IMX8MQ_CLK_PCIE1_PHY>,
 	         <&pcie0_refclk>;
 	clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
+	vph-supply = <&vgen5_reg>;
 	status = "okay";
 };
 
@@ -567,6 +568,7 @@ &pcie1 {
 	         <&clk IMX8MQ_CLK_PCIE2_PHY>,
 	         <&pcie1_refclk>;
 	clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
+	vph-supply = <&vgen5_reg>;
 	status = "okay";
 };
 

arch/arm64/boot/dts/freescale/imx8mq.dtsi

@@ -1467,10 +1467,9 @@ pcie0: pcie@33800000 {
 			#size-cells = <2>;
 			device_type = "pci";
 			bus-range = <0x00 0xff>;
-			ranges = <0x81000000 0 0x00000000 0x1ff80000 0 0x00010000 /* downstream I/O 64KB */
-			          0x82000000 0 0x18000000 0x18000000 0 0x07f00000>; /* non-prefetchable memory */
+			ranges = <0x81000000 0 0x00000000 0x1ff80000 0 0x00010000>, /* downstream I/O 64KB */
+				 <0x82000000 0 0x18000000 0x18000000 0 0x07f00000>; /* non-prefetchable memory */
 			num-lanes = <1>;
-			num-viewport = <4>;
 			interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
@@ -1505,10 +1504,9 @@ pcie1: pcie@33c00000 {
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
-			ranges =  <0x81000000 0 0x00000000 0x27f80000 0 0x00010000 /* downstream I/O 64KB */
-				   0x82000000 0 0x20000000 0x20000000 0 0x07f00000>; /* non-prefetchable memory */
+			ranges =  <0x81000000 0 0x00000000 0x27f80000 0 0x00010000>, /* downstream I/O 64KB */
+				  <0x82000000 0 0x20000000 0x20000000 0 0x07f00000>; /* non-prefetchable memory */
 			num-lanes = <1>;
-			num-viewport = <4>;
 			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;

arch/arm64/boot/dts/freescale/s32g2.dtsi

+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * NXP S32G2 SoC family
+ *
+ * Copyright (c) 2021 SUSE LLC
+ * Copyright (c) 2017-2021 NXP
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "nxp,s32g2";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0>;
+			enable-method = "psci";
+			next-level-cache = <&cluster0_l2>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x1>;
+			enable-method = "psci";
+			next-level-cache = <&cluster0_l2>;
+		};
+
+		cpu2: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x100>;
+			enable-method = "psci";
+			next-level-cache = <&cluster1_l2>;
+		};
+
+		cpu3: cpu@101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x101>;
+			enable-method = "psci";
+			next-level-cache = <&cluster1_l2>;
+		};
+
+		cluster0_l2: l2-cache0 {
+			compatible = "cache";
+		};
+
+		cluster1_l2: l2-cache1 {
+			compatible = "cache";
+		};
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	firmware {
+		psci {
+			compatible = "arm,psci-1.0";
+			method = "smc";
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 0 0x80000000>;
+
+		uart0: serial@401c8000 {
+			compatible = "nxp,s32g2-linflexuart",
+				     "fsl,s32v234-linflexuart";
+			reg = <0x401c8000 0x3000>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_EDGE_RISING>;
+			status = "disabled";
+		};
+
+		uart1: serial@401cc000 {
+			compatible = "nxp,s32g2-linflexuart",
+				     "fsl,s32v234-linflexuart";
+			reg = <0x401cc000 0x3000>;
+			interrupts = <GIC_SPI 83 IRQ_TYPE_EDGE_RISING>;
+			status = "disabled";
+		};
+
+		uart2: serial@402bc000 {
+			compatible = "nxp,s32g2-linflexuart",
+				     "fsl,s32v234-linflexuart";
+			reg = <0x402bc000 0x3000>;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_EDGE_RISING>;
+			status = "disabled";
+		};
+
+		gic: interrupt-controller@50800000 {
+			compatible = "arm,gic-v3";
+			reg = <0x50800000 0x10000>,
+			      <0x50880000 0x80000>,
+			      <0x50400000 0x2000>,
+			      <0x50410000 0x2000>,
+			      <0x50420000 0x2000>;
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+		};
+	};
+};

arch/arm64/boot/dts/freescale/s32g274a-evb.dts

+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2021 SUSE LLC
+ * Copyright (c) 2019-2021 NXP
+ */
+
+/dts-v1/;
+
+#include "s32g2.dtsi"
+
+/ {
+	model = "NXP S32G2 Evaluation Board (S32G-VNP-EVB)";
+	compatible = "nxp,s32g274a-evb", "nxp,s32g2";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* 4GiB RAM */
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0 0x80000000>,
+		      <0x8 0x80000000 0 0x80000000>;
+	};
+};
+
+/* UART (J58) to Micro USB port */
+&uart0 {
+	status = "okay";
+};

arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts

+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2021 SUSE LLC
+ * Copyright (c) 2019-2021 NXP
+ */
+
+/dts-v1/;
+
+#include "s32g2.dtsi"
+
+/ {
+	model = "NXP S32G2 Reference Design Board 2 (S32G-VNP-RDB2)";
+	compatible = "nxp,s32g274a-rdb2", "nxp,s32g2";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* 4GiB RAM */
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0 0x80000000>,
+		      <0x8 0x80000000 0 0x80000000>;
+	};
+};
+
+/* UART (J2) to Micro USB port */
+&uart0 {
+	status = "okay";
+};
+
+/* UART (J1) to Micro USB port */
+&uart1 {
+	status = "okay";
+};