drm/msm/dsi: Add phy configuration for MSM8953

Add phy configuration for 14nm dsi phy found on MSM8953 SoC. Only
difference from existing configurations are io_start addresses.
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sireesh Kodali <sireeshkodali1@gmail.com>
Link: https://lore.kernel.org/r/20210928131929.18567-3-sireeshkodali1@gmail.comSigned-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

drivers/gpu/drm/msm/dsi/phy/dsi_phy.c

@@ -627,6 +627,8 @@ static const struct of_device_id dsi_phy_dt_match[] = {
 	  .data = &dsi_phy_14nm_cfgs },
 	{ .compatible = "qcom,dsi-phy-14nm-660",
 	  .data = &dsi_phy_14nm_660_cfgs },
+	{ .compatible = "qcom,dsi-phy-14nm-8953",
+	  .data = &dsi_phy_14nm_8953_cfgs },
 #endif
 #ifdef CONFIG_DRM_MSM_DSI_10NM_PHY
 	{ .compatible = "qcom,dsi-phy-10nm",

drivers/gpu/drm/msm/dsi/phy/dsi_phy.h

@@ -48,6 +48,7 @@ extern const struct msm_dsi_phy_cfg dsi_phy_20nm_cfgs;
 extern const struct msm_dsi_phy_cfg dsi_phy_28nm_8960_cfgs;
 extern const struct msm_dsi_phy_cfg dsi_phy_14nm_cfgs;
 extern const struct msm_dsi_phy_cfg dsi_phy_14nm_660_cfgs;
+extern const struct msm_dsi_phy_cfg dsi_phy_14nm_8953_cfgs;
 extern const struct msm_dsi_phy_cfg dsi_phy_10nm_cfgs;
 extern const struct msm_dsi_phy_cfg dsi_phy_10nm_8998_cfgs;
 extern const struct msm_dsi_phy_cfg dsi_phy_7nm_cfgs;

drivers/gpu/drm/msm/dsi/phy/dsi_phy_14nm.c

@@ -1063,3 +1063,24 @@ const struct msm_dsi_phy_cfg dsi_phy_14nm_660_cfgs = {
 	.io_start = { 0xc994400, 0xc996000 },
 	.num_dsi_phy = 2,
 };
+
+const struct msm_dsi_phy_cfg dsi_phy_14nm_8953_cfgs = {
+	.has_phy_lane = true,
+	.reg_cfg = {
+		.num = 1,
+		.regs = {
+			{"vcca", 17000, 32},
+		},
+	},
+	.ops = {
+		.enable = dsi_14nm_phy_enable,
+		.disable = dsi_14nm_phy_disable,
+		.pll_init = dsi_pll_14nm_init,
+		.save_pll_state = dsi_14nm_pll_save_state,
+		.restore_pll_state = dsi_14nm_pll_restore_state,
+	},
+	.min_pll_rate = VCO_MIN_RATE,
+	.max_pll_rate = VCO_MAX_RATE,
+	.io_start = { 0x1a94400, 0x1a96400 },
+	.num_dsi_phy = 2,
+};