Commit 93b2dd12 authored by Dmitry Torokhov's avatar Dmitry Torokhov Committed by Jeff Garzik

[PATCH] prism54: whitespace cleanup

NET: prism54 - whitespace cleanup
Signed-off-by: default avatarDmitry Torokhov <dtor@mail.ru>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
parent d18e0c4a
/*
*
* Copyright (C) 2002 Intersil Americas Inc.
* Copyright (C) 2003-2004 Luis R. Rodriguez <mcgrof@ruslug.rutgers.edu>_
*
......@@ -38,7 +37,7 @@
* isl38xx_disable_interrupts - disable all interrupts
* @device: pci memory base address
*
* Instructs the device to disable all interrupt reporting by asserting
* Instructs the device to disable all interrupt reporting by asserting
* the IRQ line. New events may still show up in the interrupt identification
* register located at offset %ISL38XX_INT_IDENT_REG.
*/
......@@ -204,17 +203,19 @@ isl38xx_interface_reset(void __iomem *device_base, dma_addr_t host_address)
/* enable the interrupt for detecting initialization */
/* Note: Do not enable other interrupts here. We want the
* device to have come up first 100% before allowing any other
* device to have come up first 100% before allowing any other
* interrupts. */
isl38xx_w32_flush(device_base, ISL38XX_INT_IDENT_INIT, ISL38XX_INT_EN_REG);
udelay(ISL38XX_WRITEIO_DELAY); /* allow complete full reset */
}
void
isl38xx_enable_common_interrupts(void __iomem *device_base) {
isl38xx_enable_common_interrupts(void __iomem *device_base)
{
u32 reg;
reg = ( ISL38XX_INT_IDENT_UPDATE |
ISL38XX_INT_IDENT_SLEEP | ISL38XX_INT_IDENT_WAKEUP);
reg = ISL38XX_INT_IDENT_UPDATE | ISL38XX_INT_IDENT_SLEEP |
ISL38XX_INT_IDENT_WAKEUP;
isl38xx_w32_flush(device_base, reg, ISL38XX_INT_EN_REG);
udelay(ISL38XX_WRITEIO_DELAY);
}
......@@ -234,23 +235,21 @@ isl38xx_in_queue(isl38xx_control_block *cb, int queue)
/* send queues */
case ISL38XX_CB_TX_MGMTQ:
BUG_ON(delta > ISL38XX_CB_MGMT_QSIZE);
case ISL38XX_CB_TX_DATA_LQ:
case ISL38XX_CB_TX_DATA_HQ:
BUG_ON(delta > ISL38XX_CB_TX_QSIZE);
return delta;
break;
/* receive queues */
case ISL38XX_CB_RX_MGMTQ:
BUG_ON(delta > ISL38XX_CB_MGMT_QSIZE);
return ISL38XX_CB_MGMT_QSIZE - delta;
break;
case ISL38XX_CB_RX_DATA_LQ:
case ISL38XX_CB_RX_DATA_HQ:
BUG_ON(delta > ISL38XX_CB_RX_QSIZE);
return ISL38XX_CB_RX_QSIZE - delta;
break;
}
BUG();
return 0;
......
/*
*
* Copyright (C) 2002 Intersil Americas Inc.
*
* This program is free software; you can redistribute it and/or modify
......@@ -67,10 +66,10 @@
* @base: (host) memory base address of the device
* @val: 32bit value (host order) to write
* @offset: byte offset into @base to write value to
*
*
* This helper takes care of writing a 32bit datum to the
* specified offset into the device's pci memory space, and making sure
* the pci memory buffers get flushed by performing one harmless read
* specified offset into the device's pci memory space, and making sure
* the pci memory buffers get flushed by performing one harmless read
* from the %ISL38XX_PCI_POSTING_FLUSH offset.
*/
static inline void
......
/*
*
* Copyright (C) 2002 Intersil Americas Inc.
* (C) 2003,2004 Aurelien Alleaume <slts@free.fr>
* (C) 2003 Herbert Valerio Riedel <hvr@gnu.org>
......@@ -55,12 +54,12 @@ static const unsigned char scan_rate_list[] = { 2, 4, 11, 22,
* prism54_mib_mode_helper - MIB change mode helper function
* @mib: the &struct islpci_mib object to modify
* @iw_mode: new mode (%IW_MODE_*)
*
*
* This is a helper function, hence it does not lock. Make sure
* caller deals with locking *if* necessary. This function sets the
* mode-dependent mib values and does the mapping of the Linux
* Wireless API modes to Device firmware modes. It also checks for
* correct valid Linux wireless modes.
* caller deals with locking *if* necessary. This function sets the
* mode-dependent mib values and does the mapping of the Linux
* Wireless API modes to Device firmware modes. It also checks for
* correct valid Linux wireless modes.
*/
static int
prism54_mib_mode_helper(islpci_private *priv, u32 iw_mode)
......@@ -118,7 +117,7 @@ prism54_mib_mode_helper(islpci_private *priv, u32 iw_mode)
*
* this function initializes the struct given as @mib with defaults,
* of which many are retrieved from the global module parameter
* variables.
* variables.
*/
void
......@@ -134,7 +133,7 @@ prism54_mib_init(islpci_private *priv)
authen = CARD_DEFAULT_AUTHEN;
wep = CARD_DEFAULT_WEP;
filter = CARD_DEFAULT_FILTER; /* (0) Do not filter un-encrypted data */
dot1x = CARD_DEFAULT_DOT1X;
dot1x = CARD_DEFAULT_DOT1X;
mlme = CARD_DEFAULT_MLME_MODE;
conformance = CARD_DEFAULT_CONFORMANCE;
power = 127;
......@@ -228,7 +227,7 @@ prism54_get_wireless_stats(struct net_device *ndev)
} else
priv->iwstatistics.qual.updated = 0;
/* Update our wireless stats, but do not schedule to often
/* Update our wireless stats, but do not schedule to often
* (max 1 HZ) */
if ((priv->stats_timestamp == 0) ||
time_after(jiffies, priv->stats_timestamp + 1 * HZ)) {
......@@ -705,7 +704,7 @@ prism54_get_scan(struct net_device *ndev, struct iw_request_info *info,
* Starting with WE-17, the buffer can be as big as needed.
* But the device won't repport anything if you change the value
* of IWMAX_BSS=24. */
rvalue |= mgt_get_request(priv, DOT11_OID_BSSLIST, 0, NULL, &r);
bsslist = r.ptr;
......@@ -785,7 +784,7 @@ prism54_get_essid(struct net_device *ndev, struct iw_request_info *info,
return rvalue;
}
/* Provides no functionality, just completes the ioctl. In essence this is a
/* Provides no functionality, just completes the ioctl. In essence this is a
* just a cosmetic ioctl.
*/
static int
......@@ -1104,7 +1103,7 @@ prism54_set_encode(struct net_device *ndev, struct iw_request_info *info,
&key);
}
/*
* If a valid key is set, encryption should be enabled
* If a valid key is set, encryption should be enabled
* (user may turn it off later).
* This is also how "iwconfig ethX key on" works
*/
......@@ -1126,7 +1125,7 @@ prism54_set_encode(struct net_device *ndev, struct iw_request_info *info,
}
/* now read the flags */
if (dwrq->flags & IW_ENCODE_DISABLED) {
/* Encoding disabled,
/* Encoding disabled,
* authen = DOT11_AUTH_OS;
* invoke = 0;
* exunencrypt = 0; */
......@@ -1214,7 +1213,7 @@ prism54_get_txpower(struct net_device *ndev, struct iw_request_info *info,
vwrq->value = (s32) r.u / 4;
vwrq->fixed = 1;
/* radio is not turned of
* btw: how is possible to turn off only the radio
* btw: how is possible to turn off only the radio
*/
vwrq->disabled = 0;
......@@ -2354,17 +2353,17 @@ prism54_process_trap_helper(islpci_private *priv, enum oid_num_t oid,
handle_request(priv, mlme, oid);
send_formatted_event(priv, "Authenticate request (ex)", mlme, 1);
if (priv->iw_mode != IW_MODE_MASTER
if (priv->iw_mode != IW_MODE_MASTER
&& mlmeex->state != DOT11_STATE_AUTHING)
break;
confirm = kmalloc(sizeof(struct obj_mlmeex) + 6, GFP_ATOMIC);
if (!confirm)
if (!confirm)
break;
memcpy(&confirm->address, mlmeex->address, ETH_ALEN);
printk(KERN_DEBUG "Authenticate from: address:\t%02x:%02x:%02x:%02x:%02x:%02x\n",
printk(KERN_DEBUG "Authenticate from: address:\t%02x:%02x:%02x:%02x:%02x:%02x\n",
mlmeex->address[0],
mlmeex->address[1],
mlmeex->address[2],
......@@ -2398,10 +2397,10 @@ prism54_process_trap_helper(islpci_private *priv, enum oid_num_t oid,
handle_request(priv, mlme, oid);
send_formatted_event(priv, "Associate request (ex)", mlme, 1);
if (priv->iw_mode != IW_MODE_MASTER
if (priv->iw_mode != IW_MODE_MASTER
&& mlmeex->state != DOT11_STATE_ASSOCING)
break;
confirm = kmalloc(sizeof(struct obj_mlmeex), GFP_ATOMIC);
if (!confirm)
......@@ -2417,7 +2416,7 @@ prism54_process_trap_helper(islpci_private *priv, enum oid_num_t oid,
if (!wpa_ie_len) {
printk(KERN_DEBUG "No WPA IE found from "
"address:\t%02x:%02x:%02x:%02x:%02x:%02x\n",
"address:\t%02x:%02x:%02x:%02x:%02x:%02x\n",
mlmeex->address[0],
mlmeex->address[1],
mlmeex->address[2],
......@@ -2435,14 +2434,14 @@ prism54_process_trap_helper(islpci_private *priv, enum oid_num_t oid,
mgt_set_varlen(priv, oid, confirm, wpa_ie_len);
kfree(confirm);
break;
case DOT11_OID_REASSOCIATEEX:
handle_request(priv, mlme, oid);
send_formatted_event(priv, "Reassociate request (ex)", mlme, 1);
if (priv->iw_mode != IW_MODE_MASTER
if (priv->iw_mode != IW_MODE_MASTER
&& mlmeex->state != DOT11_STATE_ASSOCING)
break;
......@@ -2461,7 +2460,7 @@ prism54_process_trap_helper(islpci_private *priv, enum oid_num_t oid,
if (!wpa_ie_len) {
printk(KERN_DEBUG "No WPA IE found from "
"address:\t%02x:%02x:%02x:%02x:%02x:%02x\n",
"address:\t%02x:%02x:%02x:%02x:%02x:%02x\n",
mlmeex->address[0],
mlmeex->address[1],
mlmeex->address[2],
......@@ -2473,13 +2472,13 @@ prism54_process_trap_helper(islpci_private *priv, enum oid_num_t oid,
break;
}
confirm->size = wpa_ie_len;
confirm->size = wpa_ie_len;
memcpy(&confirm->data, wpa_ie, wpa_ie_len);
mgt_set_varlen(priv, oid, confirm, wpa_ie_len);
kfree(confirm);
break;
default:
......@@ -2545,10 +2544,10 @@ enum {
#define PRISM2_HOSTAPD_GENERIC_ELEMENT_HDR_LEN \
((int) (&((struct prism2_hostapd_param *) 0)->u.generic_elem.data))
/* Maximum length for algorithm names (-1 for nul termination)
/* Maximum length for algorithm names (-1 for nul termination)
* used in ioctl() */
#define HOSTAP_CRYPT_ALG_NAME_LEN 16
struct prism2_hostapd_param {
u32 cmd;
u8 sta_addr[ETH_ALEN];
......@@ -2621,7 +2620,7 @@ prism2_ioctl_set_encryption(struct net_device *dev,
&key);
}
/*
* If a valid key is set, encryption should be enabled
* If a valid key is set, encryption should be enabled
* (user may turn it off later).
* This is also how "iwconfig ethX key on" works
*/
......@@ -2643,7 +2642,7 @@ prism2_ioctl_set_encryption(struct net_device *dev,
}
/* now read the flags */
if (param->u.crypt.flags & IW_ENCODE_DISABLED) {
/* Encoding disabled,
/* Encoding disabled,
* authen = DOT11_AUTH_OS;
* invoke = 0;
* exunencrypt = 0; */
......@@ -2710,7 +2709,7 @@ prism2_ioctl_set_generic_element(struct net_device *ndev,
ret = mgt_set_varlen(priv, DOT11_OID_ATTACHMENT, attach, len);
if (ret == 0)
if (ret == 0)
printk(KERN_DEBUG "%s: WPA IE Attachment was set\n",
ndev->name);
}
......@@ -2870,7 +2869,7 @@ prism54_set_wpa(struct net_device *ndev, struct iw_request_info *info,
mlme = DOT11_MLME_AUTO;
printk("%s: Disabling WPA\n", ndev->name);
break;
case 2:
case 2:
case 1: /* WPA */
printk("%s: Enabling WPA\n", ndev->name);
break;
......
/*
*
* Copyright (C) 2002 Intersil Americas Inc.
* (C) 2003 Aurelien Alleaume <slts@free.fr>
* (C) 2003 Luis R. Rodriguez <mcgrof@ruslug.rutgers.edu>
......
/*
*
*
* Copyright (C) 2003 Herbert Valerio Riedel <hvr@gnu.org>
* Copyright (C) 2004 Luis R. Rodriguez <mcgrof@ruslug.rutgers.edu>
* Copyright (C) 2004 Aurelien Alleaume <slts@free.fr>
......@@ -23,7 +21,7 @@
#if !defined(_ISL_OID_H)
#define _ISL_OID_H
/*
/*
* MIB related constant and structure definitions for communicating
* with the device firmware
*/
......@@ -99,7 +97,7 @@ struct obj_attachment {
char data[0];
} __attribute__((packed));
/*
/*
* in case everything's ok, the inlined function below will be
* optimized away by the compiler...
*/
......@@ -154,13 +152,13 @@ enum dot11_priv_t {
/* Prism "Nitro" / Frameburst / "Packet Frame Grouping"
* Value is in microseconds. Represents the # microseconds
* the firmware will take to group frames before sending out then out
* the firmware will take to group frames before sending out then out
* together with a CSMA contention. Without this all frames are
* sent with a CSMA contention.
* Bibliography:
* sent with a CSMA contention.
* Bibliography:
* http://www.hpl.hp.com/personal/Jean_Tourrilhes/Papers/Packet.Frame.Grouping.html
*/
enum dot11_maxframeburst_t {
enum dot11_maxframeburst_t {
/* Values for DOT11_OID_MAXFRAMEBURST */
DOT11_MAXFRAMEBURST_OFF = 0, /* Card firmware default */
DOT11_MAXFRAMEBURST_MIXED_SAFE = 650, /* 802.11 a,b,g safe */
......@@ -176,9 +174,9 @@ enum dot11_maxframeburst_t {
/* Support for 802.11 long and short frame preambles.
* Long preamble uses 128-bit sync field, 8-bit CRC
* Short preamble uses 56-bit sync field, 16-bit CRC
*
*
* 802.11a -- not sure, both optionally ?
* 802.11b supports long and optionally short
* 802.11b supports long and optionally short
* 802.11g supports both */
enum dot11_preamblesettings_t {
DOT11_PREAMBLESETTING_LONG = 0,
......@@ -194,7 +192,7 @@ enum dot11_preamblesettings_t {
* Long uses 802.11a slot timing (9 usec ?)
* Short uses 802.11b slot timing (20 use ?) */
enum dot11_slotsettings_t {
DOT11_SLOTSETTINGS_LONG = 0,
DOT11_SLOTSETTINGS_LONG = 0,
/* Allows *only* long 802.11b slot timing */
DOT11_SLOTSETTINGS_SHORT = 1,
/* Allows *only* long 802.11a slot timing */
......@@ -203,7 +201,7 @@ enum dot11_slotsettings_t {
};
/* All you need to know, ERP is "Extended Rate PHY".
* An Extended Rate PHY (ERP) STA or AP shall support three different
* An Extended Rate PHY (ERP) STA or AP shall support three different
* preamble and header formats:
* Long preamble (refer to above)
* Short preamble (refer to above)
......@@ -221,7 +219,7 @@ enum do11_nonerpstatus_t {
/* (ERP is "Extended Rate PHY") Way to read NONERP is NON-ERP-*
* The key here is DOT11 NON ERP NEVER protects against
* NON ERP STA's. You *don't* want this unless
* you know what you are doing. It means you will only
* you know what you are doing. It means you will only
* get Extended Rate capabilities */
enum dot11_nonerpprotection_t {
DOT11_NONERP_NEVER = 0,
......@@ -229,13 +227,13 @@ enum dot11_nonerpprotection_t {
DOT11_NONERP_DYNAMIC = 2
};
/* Preset OID configuration for 802.11 modes
* Note: DOT11_OID_CW[MIN|MAX] hold the values of the
/* Preset OID configuration for 802.11 modes
* Note: DOT11_OID_CW[MIN|MAX] hold the values of the
* DCS MIN|MAX backoff used */
enum dot11_profile_t { /* And set/allowed values */
/* Allowed values for DOT11_OID_PROFILES */
DOT11_PROFILE_B_ONLY = 0,
/* DOT11_OID_RATES: 1, 2, 5.5, 11Mbps
/* DOT11_OID_RATES: 1, 2, 5.5, 11Mbps
* DOT11_OID_PREAMBLESETTINGS: DOT11_PREAMBLESETTING_DYNAMIC
* DOT11_OID_CWMIN: 31
* DOT11_OID_NONEPROTECTION: DOT11_NOERP_DYNAMIC
......@@ -275,7 +273,7 @@ enum oid_inl_conformance_t {
OID_INL_CONFORMANCE_NONE = 0, /* Perform active scanning */
OID_INL_CONFORMANCE_STRICT = 1, /* Strictly adhere to 802.11d */
OID_INL_CONFORMANCE_FLEXIBLE = 2, /* Use passed 802.11d info to
* determine channel AND/OR just make assumption that active
* determine channel AND/OR just make assumption that active
* channels are valid channels */
};
......
/*
*
* Copyright (C) 2002 Intersil Americas Inc.
* Copyright (C) 2003 Herbert Valerio Riedel <hvr@gnu.org>
* Copyright (C) 2003 Luis R. Rodriguez <mcgrof@ruslug.rutgers.edu>
......@@ -413,7 +412,7 @@ prism54_bring_down(islpci_private *priv)
islpci_set_state(priv, PRV_STATE_PREBOOT);
/* disable all device interrupts in case they weren't */
isl38xx_disable_interrupts(priv->device_base);
isl38xx_disable_interrupts(priv->device_base);
/* For safety reasons, we may want to ensure that no DMA transfer is
* currently in progress by emptying the TX and RX queues. */
......@@ -480,7 +479,7 @@ islpci_reset_if(islpci_private *priv)
DEFINE_WAIT(wait);
prepare_to_wait(&priv->reset_done, &wait, TASK_UNINTERRUPTIBLE);
/* now the last step is to reset the interface */
isl38xx_interface_reset(priv->device_base, priv->device_host_address);
islpci_set_state(priv, PRV_STATE_PREINIT);
......@@ -488,7 +487,7 @@ islpci_reset_if(islpci_private *priv)
for(count = 0; count < 2 && result; count++) {
/* The software reset acknowledge needs about 220 msec here.
* Be conservative and wait for up to one second. */
remaining = schedule_timeout_uninterruptible(HZ);
if(remaining > 0) {
......@@ -496,7 +495,7 @@ islpci_reset_if(islpci_private *priv)
break;
}
/* If we're here it's because our IRQ hasn't yet gone through.
/* If we're here it's because our IRQ hasn't yet gone through.
* Retry a bit more...
*/
printk(KERN_ERR "%s: no 'reset complete' IRQ seen - retrying\n",
......@@ -514,7 +513,7 @@ islpci_reset_if(islpci_private *priv)
/* Now that the device is 100% up, let's allow
* for the other interrupts --
* NOTE: this is not *yet* true since we've only allowed the
* NOTE: this is not *yet* true since we've only allowed the
* INIT interrupt on the IRQ line. We can perhaps poll
* the IRQ line until we know for sure the reset went through */
isl38xx_enable_common_interrupts(priv->device_base);
......@@ -716,7 +715,7 @@ islpci_alloc_memory(islpci_private *priv)
prism54_acl_init(&priv->acl);
prism54_wpa_bss_ie_init(priv);
if (mgt_init(priv))
if (mgt_init(priv))
goto out_free;
return 0;
......
/*
*
* Copyright (C) 2002 Intersil Americas Inc.
* Copyright (C) 2002 Intersil Americas Inc.
* Copyright (C) 2003 Herbert Valerio Riedel <hvr@gnu.org>
* Copyright (C) 2003 Luis R. Rodriguez <mcgrof@ruslug.rutgers.edu>
* Copyright (C) 2003 Aurelien Alleaume <slts@free.fr>
......@@ -72,12 +71,12 @@ struct islpci_bss_wpa_ie {
u8 bssid[ETH_ALEN];
u8 wpa_ie[MAX_WPA_IE_LEN];
size_t wpa_ie_len;
};
typedef struct {
spinlock_t slock; /* generic spinlock; */
u32 priv_oid;
/* our mib cache */
......@@ -85,7 +84,7 @@ typedef struct {
struct rw_semaphore mib_sem;
void **mib;
char nickname[IW_ESSID_MAX_SIZE+1];
/* Take care of the wireless stats */
struct work_struct stats_work;
struct semaphore stats_sem;
......@@ -120,7 +119,7 @@ typedef struct {
struct net_device *ndev;
/* device queue interface members */
struct isl38xx_cb *control_block; /* device control block
struct isl38xx_cb *control_block; /* device control block
(== driver_mem_address!) */
/* Each queue has three indexes:
......
/*
*
* Copyright (C) 2002 Intersil Americas Inc.
* Copyright (C) 2004 Aurelien Alleaume <slts@free.fr>
* This program is free software; you can redistribute it and/or modify
......@@ -48,7 +47,7 @@ islpci_eth_cleanup_transmit(islpci_private *priv,
/* read the index of the first fragment to be freed */
index = priv->free_data_tx % ISL38XX_CB_TX_QSIZE;
/* check for holes in the arrays caused by multi fragment frames
/* check for holes in the arrays caused by multi fragment frames
* searching for the last fragment of a frame */
if (priv->pci_map_tx_address[index] != (dma_addr_t) NULL) {
/* entry is the last fragment of a frame
......@@ -285,7 +284,7 @@ islpci_monitor_rx(islpci_private *priv, struct sk_buff **skb)
(struct avs_80211_1_header *) skb_push(*skb,
sizeof (struct
avs_80211_1_header));
avs->version = cpu_to_be32(P80211CAPTURE_VERSION);
avs->length = cpu_to_be32(sizeof (struct avs_80211_1_header));
avs->mactime = cpu_to_be64(le64_to_cpu(clock));
......@@ -391,7 +390,7 @@ islpci_eth_receive(islpci_private *priv)
struct rx_annex_header *annex =
(struct rx_annex_header *) skb->data;
wstats.level = annex->rfmon.rssi;
/* The noise value can be a bit outdated if nobody's
/* The noise value can be a bit outdated if nobody's
* reading wireless stats... */
wstats.noise = priv->local_iwstatistics.qual.noise;
wstats.qual = wstats.level - wstats.noise;
......
/*
*
* Copyright (C) 2002 Intersil Americas Inc.
*
* This program is free software; you can redistribute it and/or modify
......
/*
*
* Copyright (C) 2002 Intersil Americas Inc.
* Copyright (C) 2003 Herbert Valerio Riedel <hvr@gnu.org>
*
......@@ -40,8 +39,8 @@ static int init_pcitm = 0;
module_param(init_pcitm, int, 0);
/* In this order: vendor, device, subvendor, subdevice, class, class_mask,
* driver_data
* If you have an update for this please contact prism54-devel@prism54.org
* driver_data
* If you have an update for this please contact prism54-devel@prism54.org
* The latest list can be found at http://prism54.org/supported_cards.php */
static const struct pci_device_id prism54_id_tbl[] = {
/* Intersil PRISM Duette/Prism GT Wireless LAN adapter */
......@@ -132,15 +131,15 @@ prism54_probe(struct pci_dev *pdev, const struct pci_device_id *id)
/* 0x40 is the programmable timer to configure the response timeout (TRDY_TIMEOUT)
* 0x41 is the programmable timer to configure the retry timeout (RETRY_TIMEOUT)
* The RETRY_TIMEOUT is used to set the number of retries that the core, as a
* Master, will perform before abandoning a cycle. The default value for
* RETRY_TIMEOUT is 0x80, which far exceeds the PCI 2.1 requirement for new
* devices. A write of zero to the RETRY_TIMEOUT register disables this
* function to allow use with any non-compliant legacy devices that may
* execute more retries.
* The RETRY_TIMEOUT is used to set the number of retries that the core, as a
* Master, will perform before abandoning a cycle. The default value for
* RETRY_TIMEOUT is 0x80, which far exceeds the PCI 2.1 requirement for new
* devices. A write of zero to the RETRY_TIMEOUT register disables this
* function to allow use with any non-compliant legacy devices that may
* execute more retries.
*
* Writing zero to both these two registers will disable both timeouts and
* *can* solve problems caused by devices that are slow to respond.
* Writing zero to both these two registers will disable both timeouts and
* *can* solve problems caused by devices that are slow to respond.
* Make this configurable - MSW
*/
if ( init_pcitm >= 0 ) {
......@@ -241,7 +240,7 @@ prism54_remove(struct pci_dev *pdev)
isl38xx_disable_interrupts(priv->device_base);
islpci_set_state(priv, PRV_STATE_OFF);
/* This bellow causes a lockup at rmmod time. It might be
* because some interrupts still linger after rmmod time,
* because some interrupts still linger after rmmod time,
* see bug #17 */
/* pci_set_power_state(pdev, 3);*/ /* try to power-off */
}
......
/*
*
* Copyright (C) 2002 Intersil Americas Inc.
* Copyright 2004 Jens Maurer <Jens.Maurer@gmx.net>
*
......@@ -502,7 +501,7 @@ islpci_mgt_transaction(struct net_device *ndev,
printk(KERN_WARNING "%s: timeout waiting for mgmt response\n",
ndev->name);
/* TODO: we should reset the device here */
/* TODO: we should reset the device here */
out:
finish_wait(&priv->mgmt_wqueue, &wait);
up(&priv->mgmt_sem);
......
/*
*
* Copyright (C) 2002 Intersil Americas Inc.
* Copyright (C) 2003 Luis R. Rodriguez <mcgrof@ruslug.rutgers.edu>
*
......@@ -36,8 +35,8 @@ extern int pc_debug;
/* General driver definitions */
#define PCIDEVICE_LATENCY_TIMER_MIN 0x40
#define PCIDEVICE_LATENCY_TIMER_VAL 0x50
#define PCIDEVICE_LATENCY_TIMER_MIN 0x40
#define PCIDEVICE_LATENCY_TIMER_VAL 0x50
/* Debugging verbose definitions */
#define SHOW_NOTHING 0x00 /* overrules everything */
......
/*
/*
* Copyright (C) 2003,2004 Aurelien Alleaume <slts@free.fr>
*
* This program is free software; you can redistribute it and/or modify
......@@ -503,7 +503,7 @@ mgt_set_varlen(islpci_private *priv, enum oid_num_t n, void *data, int extra_len
}
if (ret || response_op == PIMFOR_OP_ERROR)
ret = -EIO;
} else
} else
ret = -EIO;
/* re-set given data to what it was */
......@@ -727,7 +727,7 @@ mgt_commit(islpci_private *priv)
* MEDIUMLIMIT,BEACONPERIOD,DTIMPERIOD,ATIMWINDOW,LISTENINTERVAL
* FREQUENCY,EXTENDEDRATES.
*
* The way to do this is to set ESSID. Note though that they may get
* The way to do this is to set ESSID. Note though that they may get
* unlatch before though by setting another OID. */
#if 0
void
......
/*
/*
* (C) 2004 Margit Schubert-While <margitsw@t-online.de>
*
* This program is free software; you can redistribute it and/or modify
......@@ -16,7 +16,7 @@
*
*/
/*
/*
* Compatibility header file to aid support of different kernel versions
*/
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment