ARM: mxs: dt: Add Crystalfontz CFA-10058 device tree

The CFA-10058 is a breakout board for the CFA-10036 that has Ethernet, USB and a
5" LCD screen on it.
Signed-off-by: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

arch/arm/boot/dts/Makefile

@@ -145,6 +145,7 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
 	imx28-cfa10055.dtb \
 	imx28-cfa10056.dtb \
 	imx28-cfa10057.dtb \
+	imx28-cfa10058.dtb \
 	imx28-evk.dtb \
 	imx28-m28evk.dtb \
 	imx28-sps1.dtb \

arch/arm/boot/dts/imx28-cfa10058.dts

+/*
+ * Copyright 2013 Crystalfontz America, Inc.
+ * Copyright 2013 Free Electrons
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/*
+ * The CFA-10058 is an expansion board for the CFA-10036 module, thus we
+ * need to include the CFA-10036 DTS.
+ */
+/include/ "imx28-cfa10036.dts"
+
+/ {
+	model = "Crystalfontz CFA-10058 Board";
+	compatible = "crystalfontz,cfa10058", "crystalfontz,cfa10036", "fsl,imx28";
+
+	apb@80000000 {
+		apbh@80000000 {
+			pinctrl@80018000 {
+				usb_pins_cfa10058: usb-10058@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				lcdif_pins_cfa10058: lcdif-10058@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
+						0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
+						0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
+						0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+			};
+
+			lcdif@80030000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&lcdif_24bit_pins_a
+						 &lcdif_pins_cfa10058>;
+				display = <&display>;
+				status = "okay";
+
+				display: display {
+					bits-per-pixel = <32>;
+					bus-width = <24>;
+
+					display-timings {
+						native-mode = <&timing0>;
+						timing0: timing0 {
+							clock-frequency = <30000000>;
+							hactive = <800>;
+							vactive = <480>;
+							hback-porch = <40>;
+							hfront-porch = <40>;
+							vback-porch = <13>;
+							vfront-porch = <29>;
+							hsync-len = <8>;
+							vsync-len = <8>;
+							hsync-active = <0>;
+							vsync-active = <0>;
+							de-active = <1>;
+							pixelclk-active = <1>;
+						};
+					};
+				};
+			};
+		};
+
+		apbx@80040000 {
+			lradc@80050000 {
+				fsl,lradc-touchscreen-wires = <4>;
+				status = "okay";
+			};
+
+			pwm: pwm@80064000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pwm3_pins_b>;
+				status = "okay";
+			};
+
+			usbphy1: usbphy@8007e000 {
+				status = "okay";
+			};
+		};
+	};
+
+	ahb@80080000 {
+		usb1: usb@80090000 {
+			vbus-supply = <&reg_usb1_vbus>;
+			pinctrl-0 = <&usbphy1_pins_a>;
+			pinctrl-names = "default";
+			status = "okay";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		reg_usb1_vbus: usb1_vbus {
+			pinctrl-names = "default";
+			pinctrl-0 = <&usb_pins_cfa10058>;
+			compatible = "regulator-fixed";
+			regulator-name = "usb1_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio0 7 1>;
+		};
+	};
+
+	ahb@80080000 {
+		mac0: ethernet@800f0000 {
+			phy-mode = "rmii";
+			pinctrl-names = "default";
+			pinctrl-0 = <&mac0_pins_a>;
+			phy-reset-gpios = <&gpio2 21 0>;
+			phy-reset-duration = <100>;
+			status = "okay";
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 3 5000000>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+};